Wirepath Home Systems C4-KC120277 Installation Manual

™

Warnings and considerations

Configurable Keypad

Installation Guide

Supported model

• C4-KC120277 Wireless Configurable Keypad

Introduction

The Control4® Configurable Keypad is intended for use in a Control4 system. It
installs in a standard wallbox using typical wiring standards and communicates to
the Control4 system using a wireless connection.

Box contents

• Configurable Keypad

• Keycap Button Kit

• Wire nuts

• Warranty card

• Configurable Keypad Installation Guide (this document)

• Keypad Button Installation Guide

Specifications

The specifications are described below.

WARNING! Turn OFF electrical power before installing or servicing this

product. Improper use or installation can cause SERIOUS INJURY, DEATH
or LOSS/DAMAGE OF PROPERTY.

ATTENTION! Coupez l’alimentation électrique avant d’installer ou de

réparer ce produit. Une mauvaise installation ou utilisation peut entraîner
des blessures graves, décès ou perte / dommages à la propriété.

WARNING! This device must be protected by a circuit breaker (20A max).
ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)

WARNING! Ground this device in accordance with the National Electric

Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s
contact with a metal wallbox for adequate grounding. Use the device’s
ground wire to make a secure connection to the safety ground of the
electrical system.

ATTENTION! Cet appareil doit être en conformité avec le Code national de

l’électricité (NEC). Ne comptez pas uniquement au contact de la plaque
avant avec un boîtier mural métallique pour la mise à la terre adéquate.
Utilisez cet appareil à la terre de l’appareil pour établir une connexion
sécurisée au système électrique.

IMPORTANT! This device must be installed by a licensed electrician in

accordance with all national and local electrical codes.

IMPORTANT! If you are unsure about any part of these instructions,

consult a qualified electrician.

IMPORTANT! Use this device only with copper or copper-clad wire. Do

not use aluminum wiring. This product has not been approved for use with
aluminum wiring.

IMPORTANT! Using this product in a manner other than outlined in this

document voids your warranty. Further, Control4 is NOT liable for any
damage incurred with the misuse of this product. See “Troubleshooting.”

Model number C4-KC120277-xx

Power requirements 120-277V AC +/-10% 50/60 Hz

36-48V DC
This device requires a neutral AC connection.

Power consumption 120V: 350mW

277V: 540mW
36V DC: 430mW

Environmental

Operational temperature 0 to 40 ˚C (32 to 104 ˚F)

Humidity 5% to 95% non-condensing

Storage -20 to 70 ˚C (-4 to 158 ˚F)

Miscellaneous

Control communications Zigbee, IEEE 802.15.4, 2.4 GHz, 15-channel

Wallbox volume 4.75 cubic inches

Weight 0.05 kg (0.12 lb.)

Shipping weight 0.08 kg (0.18 lb.)

Copyright ©2021, Wirepath Home Systems, LLC. All rights reserved. Control4 and SnapAV and
their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC,
dba “Control4” and/or dba “SnapAV” in the United States and/or other countries. 4Store, 4Sight,
Control4 My Home, Snap AV, Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma,
Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong Vers­abox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE
are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and
brands may be claimed as the property of their respective owners. All specifications subject to
change without notice.

spread spectrum radio

200-00309-G 20210409MS

IMPORTANT! Do NOT use a power screwdriver to install this device. If you

do, you may overtighten the screws and strip them. Also, overtightening
the screws may interfere with proper button operation.

IMPORTANT! This is an electronic device with intricate components.

Handle and install with care!

IMPORTANT! When used in conjunction with an Auxiliary Keypad

(C4-KA-xx), the wire connecting the Auxiliary Keypad to the Configurable
Keypad must not exceed 45 m (150 ft.) at 120V AC, and 30 m (100 ft.) at
277VAC.

Installation instructions

1 Ensure that the location and intended use meet the following criteria:

• When replacing a traditional 3-way switch, refer to the “Two-Location”
sample wiring configurations provided in the appropriate load control
device installation guide.

• Install in accordance with all national and local electrical codes.

• The range and performance of the wireless control system is highly
dependent on the following: (1) distance between devices; (2) layout
of the home; (3) walls separating devices; and (4) electrical equipment
located near devices.

2 Turn o the local electrical power by either switching o the circuit breaker or

removing the fuse from the fuse box. To ensure the wires do NOT have power
running to them, use an inductive voltage detector.

NOTE: The wallbox wiring shown in this document is an example. Your

wire colors and functions may dier. If you are not sure which wires are
the Line In/Hot, Neutral, and Earth Ground wires, have a trained electrician
do the installation.

3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch

from the wire end (see Figure 1).

Strip wire insulation

Figure 1.

IMPORTANT!

“Warnings and Considerations,” may result in an installation less immune
to damage caused by electrical disturbances, such as ESD or lightning,
and may void the warranty.

Not grounding this product, as described in the section,

6 Align the keypad to the wallbox (the model # label should be at the bottom)

and fasten it with screws. Tighten the screws until the back side of the yoke
plate is even with the wall surface, but no further. Overtightening can warp
the configurable keypad and cause mechanical malfunction.

7 Install the Top Actuator Bar, Bottom Sensor Bar, and buttons following the

instructions in the “Button Installation” section below.

8 Install the Control4 Faceplate following the instructions in the Faceplate

Installation Guide or attach a standard Decora-style faceplate.

9 Turn on power at the circuit breaker or replace the fuse from

the fuse box.

Button installation

For information about how to install or remove the buttons on the configurable
keypad, see the Keypad Buttons Installation Guide.

Operation and configuration

On initial power up, all status LEDs on the keypad will illuminate green indicating
that the device has power. Until the keypad has been configured into a Control4
system, it will not control any loads. To set up this keypad for use with a Control4
system, refer to the Composer Pro User Guide.

4 Identify and connect the keypad wires to the wallbox wires using the wire

nuts as shown in Figure 2 below.

Figure 2. Keypad wiring

TIP:

If you are using a Control4 push-on (screwless) faceplate in a multi­gang installation, attach the black faceplate sub-plate to all of the devices
that will be installed into the wallbox prior to attaching the devices to the
wallbox. This will help ensure that all the devices are properly aligned and
on the same plane after installation.

5 Fit the wires back into the wallbox. Bend the wires in a zigzag pattern so that

they easily fold into the wallbox (Figure 3).

Figure 3.

Bend the wires

Button tap sequences

The button tap sequences are defined in the table below. Button tap sequences
that require a single (1) button should use the top-most button installed on the
keypad. Button tap sequences requiring two (2) buttons should use the top-most
and bottom-most buttons installed on the keypad.

Function Button sequence

Identify 4

Zigbee channel 7

Reboot 15

Factory reset 9-4-9

Leave mesh and reset 13-4-13

Troubleshooting

If the LEDs do not light up indicating that the keypad is receiving power::

• Ensure circuit breaker is not turned OFF or tripped.

• Check for proper wiring (see Step 2 in “Installation Instructions”).

Care and cleaning

• Do NOT paint the keypad or its wall plate.

• Do NOT use any chemical cleaners to clean the keypad.

• Clean surface of the keypad with a soft damp cloth as needed.

Warranty and legal notices

Find details of the product’s Limited Warranty at snapav.com/warranty or request
a paper copy from Customer Service at 866.424.4489. Find other legal resources,
such as regulatory notices and patent information, at snapav.com/legal.