Wintal A-1200D Instruction Manual

In-Wall Audio/Video CAT5 Extender with Infrared Manual

SPECIFICATIONS:
Interface:

Video: 1x RCA jack
Audio: 2x RCA jacks for Left and Right Audio
UTP: 110-type rear punchdown or RJ-45

Impedance:

Video: 75 ohm unbalanced
Audio: 600 ohm unbalanced
UTP: 100ohm balanced

Bandwidth:

Video: DC~12 MHz
Audio: 50 Hz~15 KHz

Distance:

Audio/Color Video: Category 5e UTP cable up to 300

meters

IMPORTANT

Do not route audio/video cables through the same‧
cable holes as the AC power cables.
For safety, all audio/video cables should be separated‧
from parallel AC power lines by at least 15cm
whenever possible.
Avoid kinking the cable.‧
Do not attach cable ti‧ e-downs too tightly. The cable

fastening hardware should not compress the cable
sheath.

‧Do not bend the cable sharply. Be especially

careful to dress the cables properly after passing
them through a hole as the edges of the hole can
compress or even damage the cable sheath.
Follow all warnings on the products.‧
For your safety, do not use this or any electrical‧
product near water (unless specifically designed for
wet areas).
Do not install wiring during thunder and lightning‧
storms.

Use caution when han‧ dling or installing any

computer, telephone, video, or electrical devices.

INSTALLATION
For RJ45

1. Connect the Extender using Cat5 UTP cable
(Purchased separately). The Cat5 UTP cable, if
purchased in bulk, will be wired using 568A or 568B wiring
standard as shown in the table blow.

2. Fasten insert and wallplate to electrical box using

supplied screws.

For 110-type IDC

1. Strip off approximately 5cm of the Category 5e

cable jacket, using the appropriate cable
stripping tool.

2. Separate the pairs according to color (Brown/

Brown-White, Green / Green - White, and Orange
/Orange-White).

3. To terminate, place each wire into the insulation

displacement contacts (IDC) b y matc hing t he wire c ol or
with the applicable colors on the punchdown block
(see the figure below).

TIP: We recommend untwisting the pairs no more than 3cm

4. If using a 110-type punchdown tool, place the tool over each

wire with the cutting blade facing outside of the IDC and
punch down firmly.

5. Repeat this process with each pair.

6. Install included termination caps firmly onto the IDC.

7. Fasten insert and wallplate to electrical box using supplied

screws

from termination point.

Dual Band Surface Mount Mini IR Receiver

Features

1. CFL friendly–allows installations in areas with
compact fluorescent lighting. Works in most
lighting environments.

2. Blue IR confirmation LED.

3. Wide band IR receives IR from many types of
remotes.

4. Self-adhesive tape for quick and easy fixing on any
flat surface.

5. 3 meters cable with 3.5mm stereo mini-plug.

Specifications
Receive Frequency Range….……. 34 kHz to 60 kHz

Transmit Frequencies………....……38 KHz & 56 kHz

Range……………….………............... 40ft. @ 38 KHz

…….……….……………………25ft. @ 56 KHz
Power………….…………………..12VDC, 31mA max.
Dimensions………………..……45L x 14W x 13H mm
Cord Length…………..……………………….10ft (3m)

Connector T ype………....1/8” (3.5mm) TRS mini plug

Weight……………...……..…………………………28 g

 Dual IR Emitter

B. Attach emitter at inside of shelf

1. Attach emitter on above or below of the IR sensor.

2. Less reliable activated.

A. Standard installation

1. IR emitter attached directly to IR
sensor window.

2. More reliable activated

C. Cabinet with door installation

1. Attach emitter on door, round shape facing the IR
sensor.

2. Less reliable activated.