Wintal A-1028 Instruction Manual

3-T erminal Audio/V ideo Wall Plate Instruction Manual

CHOOSING A MOUNTING LOCATION

Choose a location for the wall plate where:
 Either wiring exists, or you can easily run wire through the partition(s) /wall(s)

to the location.

 The location does not interfere with electrical wiring or framing members

behind the wall.

INSTALLATION

You can mount your Audio/Video Wall Connector with the standard electrical
box, or mount it with the supplied mounting bracket.

Mounting with the standard electrical box

1. Connect the VCR’s, or camcorder’s, or video signal cable to the yellow jack’s
+ and – terminals on the back of the wall plate.

Note: When connecting wires to the + and – terminals, be sure not to let any
strayed wire of the positive and negative wires touch each other to avoid
any possible damage to the audio/video equipment.

2. Insert the audio source L channel output + and – wires into the white jack’s +
and – terminals on the back of the wall plate, then tighten the screws.

3. Insert the audio source R channel output + and – wires into the red jack’s +
and – terminals on the back of the wall plate, then tighten the screws.

4. Insert the supplied two screws in the screw holes on the wall plate and screw
holes on the electrical box’s mounting bracket.

5. Tighten the screws to mount the wall plate to the electrical box.

6. Connect the stereo TV’s video input wire to the yellow jack on the front of the
wall plate.

7. Connect the stereo TV’s or stereo amplifier/receiver’s audio L channel input
wire to the white jack.

8. Connect the stereo TV’s or stereo amplifier/receiver’s audio R channel input
wire to the red jack.

3-T e rminal Audio/Video Wall Plate Instruction Manual

CHOOSING A MOUNTING LOCATION

Choose a location for the wall plate where:
 Either wiring exists, or you can easily run wire through the partition(s) /wall(s)

to the location.

 The location does not interfere with electrical wiring or framing members

behind the wall.

INSTALLATION

You can mount your Audio/Video Wall Connector with the standard electrical
box, or mount it with the supplied mounting bracket.

Mounting with the standard electrical box

1. Connect the VCR’s, or camcorder’s, or video signal cable to the yellow jack’s
+ and – terminals on the back of the wall plate.

Note: When connecting wires to the + and – terminals, be sure not to let any
strayed wire of the positive and negative wires touch each other to avoid
any possible damage to the audio/video equipment.

2. Insert the audio source L channel output + and – wires into the white jack’s +
and – terminals on the back of the wall plate, then tighten the screws.

3. Insert the audio source R channel output + and – wires into the red jack’s +
and – terminals on the back of the wall plate, then tighten the screws.

4. Insert the supplied two screws in the screw holes on the wall plate and screw
holes on the electrical box’s mounting bracket.

5. Tighten the screws to mount the wall plate to the electrical box.

6. Connect the stereo TV’s video input wire to the yellow jack on the front of the
wall plate.

7. Connect the stereo TV’s or stereo amplifier/receiver’s audio L channel input
wire to the white jack.

8. Connect the stereo TV’s or stereo amplifier/receiver’s audio R channel input
wire to the red jack.

Mounting the wall connector on a partition

1. Mark a 13/4 inch × 4 inch (4.4cm×10.2cm) outline on the wall.

2. Drill a

3

/8 inch (1 cm) hole in one corner of the outline.

Mounting the wall connector on a partition

1. Mark a 13/4 inch × 4 inch (4.4cm×10.2cm) outline on the wall.

2. Drill a

3

/8 inch (1 cm) hole in one corner of the outline.

3. Use a saber or keyhole saw to cut along the

4.4

Cut Ou

4.4

Cut Ou

outline, then remove the cut-out portion.

4. Run wiring from the source through the partition(s)
and stretch it out through the cut opening.

cm

(1-3/4")

1cm (3/8" )
Hole

.

5. Insert the VCR’s or camcorder’s video signal cable
in the yellow jack’s + and – terminals on the back
of the wall plate.

6. Insert the audio source L channel output + and –

10.2cm(4")

wires into the white jack’s + and – terminals on
the back of the wall plate, then tighten the screws.

7. Insert the audio source R channel output + and –

Flat Strip

wires into the red jack’s + and – terminals on the
back of the wall plate, then tighten the screws.

8. Assemble the two mounting brackets (formed

Formed Strip

and flat strips) using the four supplied medium
screws. Then place the assembled brackets in the
opening and twist them to fit the opening. Tighten
the four screws to secure the assembly.

Tighten
Medium
Screws

9. Insert the two supplied short screws into the
screw holes on the w al l p la te a nd ce nte r holes on

t in Wall

the molded brackets, then tighten the screws.

10. Connect the stereo TV’s video input wire to the yellow jack on the front of
the wall plate.

11. Connect the stereo TV’s or stereo amplifier/receiver’s audio L channel input
wire to the white jack.

12. Connect the stereo TV’s or stereo amplifier/receiver’s audio R channel input
wire to the red jack.

3. Use a saber or keyhole saw to cut along the
outline, then remove the cut-out portion.

4. Run wiring from the source through the partition(s)

and stretch it out through the cut opening.

cm

(1-3/4")

1cm (3/8" )
Hole

.

5. Insert the VCR’s or camcorder’s video signal cable

in the yellow jack’s + and – terminals on the back
of the wall plate.

6. Insert the audio source L channel output + and –

10.2cm(4")

wires into the white jack’s + and – terminals on
the back of the wall plate, then tighten the screws.

7. Insert the audio source R channel output + and –

Flat Strip

wires into the red jack’s + and – terminals on the
back of the wall plate, then tighten the screws.

8. Assemble the two mounting brackets (formed

Formed Strip

and flat strips) using the four supplied medium
screws. Then place the assembled brackets in the
opening and twist them to fit the opening. Tighten
the four screws to secure the assembly.

Tighten
Medium
Screws

9. Insert the two supplied short screws into the

screw holes on the w al l p la te a nd ce nte r holes on

t in Wall

the molded brackets, then tighten the screws.

10. Connect the stereo TV’s video input wire to the yellow jack on the front of

the wall plate.

11. Connect the stereo TV’s or stereo amplifier/receiver’s audio L channel input

wire to the white jack.

12. Connect the stereo TV’s or stereo amplifier/receiver’s audio R channel input

wire to the red jack.