Winston Porter W004924961 Assembly Instructions

Label Picture Description QTY

A Seat Base 1

B Backrest 1

C Seat Cushion 2

Assembly Instructions

Caution: You must read this before you proceed

Loveseat

Part List

Page 1 OF 13

D Left Back Cushion 1

E Right Back Cushion 1

F Left Arm 1

G Right Arm 1

H Front Seat Board 1

I Back Seat Board 1

J

Wood Leg

(with Gasket)

4

Page 2 OF 13

K

Middle Leg

(with Gasket)

1

Label Picture Description QTY

① Gasket 3

② Allen Key 1

Before

Begining

Assembly:

Hardware

Assembly Preparation

Page 3 OF 13

Assembly Steps

This Loveseat has multiple parts and may require about 30 minutes to assemble. To give
you an overview of the Loveseat parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.

Overview

Wood Leg (J)

FRONT FACING

Backrest (B)

Seat Cushion (C)

Right Arm (G)

Right Back Cushion(E)

Left Back Cushion (D)

Left Arm (F)

Front Seat Board (H)

Page 4 OF 13

Step 2

Take the Seat Base(A), Backrest(B), Seat Cushions(C), Left Back Cushion(D), Right Back
Cushion(E), Left Arm(F), Right Arm(G), Front Seat Board(H), Back Seat Board(I) and
Small Bubble Package out of the carton and place them on a clean, non-marring surface.

Open the Small Bubble Package to take out the Wood Legs(J), Middle Leg Gasket(K),
Gaskets(①) and Allen Key(②).

Step 1

A

B

C

D

E

G

H

Small Bubble Package

J

①

Small Bubble Package

C

F

I

K

②

Page 5 OF 13

Turn the Left Arm(F) and Right Arm(G) facedown as pictured.
Install the Wood Legs(J) at the bottom of the Left Arm(F) and Right Arm(G).
Insert threaded stem into the mounting positions at the bottom of Left Arm(F) and Right
Arm(G). Tighten by turning the Leg clockwise.

Note:The use of Gaskets are OPTIONAL and are especially useful to help alleviate
slight wobbles. Some Legs may need more than one gasket whilst some Legs may
not need any.

Step 3

①

J

G

F

F

G

Page 6 OF 13

With assistance from your adult partner, postion the Left Arm(F) and Right Arm(G) as
pictured, align the Back Seat Board(I) between both Arms.
Then place the hooks on the ends of the Back Seat Board(I) onto the two raised Bolts on
the Left Arm(F) and Right Arm(G) and tighten with Allen Key(②).

Note: The Bolts on the arms shouldn't be removed but may need to be loosened to
fit the hooks.

Step 4

F

G

I

I

I

②

F

F

Page 7 OF 13

Repeat the same process from Step 3, to assemble the Front Seat Board(H).

Step 4

F

G

I

H

H

H

②

G

G

Page 8 OF 13

Install the Middle Leg(K) at the bottom of the Seat Base(A).
Insert threaded stem into the mounting position at the bottom of the Seat Base(A), tighten
by turning the Leg clockwise.

Note: The use of Gaskets are OPTIONAL and are especially useful to help alleviate
slight wobbles. Some Legs may need more than one gasket whilst some Legs may
not need any.

Step 5

K

K

①

A

Page 9 OF 13

With assistance from your adult partner, hold up the Seat Base(A) and align it to the
Loveseat Base.
Intersect the Mounting Brackets on the Seat Base(A) with those on the Left Arm(F) and
Right Arm(G), then push firmly down on the Seat Base(A) until it locks into position.

Step 6

A

F

G

H

I

Page 10 OF 13

Step 7

With assistance from your adult partner, hold up the Backrest(B), while standing behind
the Loveseat Base.
Align the mounting brackets on both sides of the Backrest(B) with those on the Left
Arm(F) and Right Arm(G).
Then slide Backrest(B) downward to make sure it locks into place as pictured.

Put the two Seat Cushions(C) on the Seat Base(A).

Step 8

B

F

G

C

A

B

B

F

G

H

H

G

Page 11 OF 13

Place Left Back Cushion(D) and Right Back Cushion(E) on Backrest(B).
Your Loveseat is ready for use.

This Loveseat can only be used on a flat, level surface.

Step 9

B

D

E

Page 12 OF 13

Page 13 OF 13