ALL WEATHER WICKER PATIO DOUBEL-SEATING CHAIR WITH COFFEE TABLE
ASSEMBLY INSTRUCTION
WARNING : This ch air is not a toy. The proper us e of the chair
!
is for two- perso n seating max. Fur ther, t he chair is not to be us ed
for stand ing pur poses and it will no t funct ion as a stool or step ladder. B eside s, please use this c hair on e ven surfaces onl y. The
single se ating t ested for use at a max w eight o f 350 lb. Improper
use of this p roduc t or failure to use as d irect ed may result in
injury. T his cha ir is not intended f or comm ercial use.
IMPORTANT:
Please re ad all th e instructions a nd warn ings before asse mblin g. In order to make th e
whole pro duct ad just to the best, pl ease in stall all the scre ws on the p roduct and
tighten a ll the sc rews after adjus ting th e product which ca n stand o n the floor even.
WARNING:
·Please kee p all children and pets awa y from the assembly area. I n addition, childr en and
pets shoul d be su pervised when they a re in the area of product con struction.
·Please mak e sure to keep the assembly a rea at least 6 feet from any obstr uction such as
a fence, gar age, house, overha nging branches, la undry line or electr ica l wires.
·Some parts m ay co ntain sharp edges. Ther efo re, when assemb ling and using this
product, b asic safety precau tions should alway s be fo llowed to reduce the r isk of personal
injury and d amage to the product. Ple ase read all instruc tions before assem bly and use.
·Please che ck all bolts for tightnes s before use. IMPORTANT-check and tigh ten bolts
often to kee p the m secure!
·The chair is not to b e use d for standing purpo ses and will not function a s a sto ol or
stepladd er.
Again, thi s chair is used on even surfa ces only.
·The single s eating tested for use at a max wei ght of 350 lb. Improper use o f thi s product or
failure to u se as
directed m ay result in injury. Not intended fo r com mercial use.
CARE & MAINTENANCE
SPILLS
Please immed iatel y wipe up the spill usi ng a whit e damp cloth. Repea t proce ss if necessary
until stain is g one.
FABRIC CARE
Please use col d water a nd hand wash, use non -chlo rine bleach when ne eded, l ay flat to dry.
Cool iron if nec essar y. Do no t dry clean.
RESIN WICKER P RODUC T CAR E
Before using , pleas e clean the product c omple tely with a soft dry to wel. Mo reover, when the
chair not in use , you sho uld wipe off a ny dirt or los e objec ts, was h with a mild solutio n of
soap and water, r inse th oroughly and dry co mplet ely. Please d o not use strong dete rgent o r
abrasive cle aners . Since nuts and bolt s can loo sen over time, so ple ase che ck nuts and
bolts on all cha irs and t ables, re-tight en if nec essary.
Parts List:
NO.
1
3
7 8
9
11
21
A
Part
Left arm
Chair back
Chair back
(With Foot)
Glass
Table Top
Lower Shelf
Back
Cushion
Screw
(6x40mm)
Screw
D
(6x15mm)
1
Qty
1
1
1
1
1
2
4
12
Image
NO.
Right arm
2
Seat Panel
4
Seat Panel
(With Foot)
10
20
Table leg
Seat
Cushion
Screw
C
(6x20mm)
L
Allen wrench
Part
Qty
1
1
1
4
2
12
1
Image
2
L
L
C
C
L
L
D
D
11
3
10
9
Step1: Secur e 4 table l egs (10) to glass tab le top wi th 8 screws (D) by usin g allen w rench
(L). Do not tigh ten all s crews now.
D
L
L
D
11
10
9
Step2:Secu re lowe r shelf (11) to middle of the t able le gs with 4 s crews(D) b y using a llen
wrench (L). Do n ot full y tighten now.
4
L
C
Step 1: Insert seat panel (4) into the t wo holes on chair back (3), then secure
them with 2 screws (C) by using allen wr ench (L). Do not tighten all screws
now.
1
L
C
3
4
1
L
A
Step3: Verify t he alig nment and adjust, f ully ti ghten all the screw s now. The coffee ta ble is
assembled.
L
C
4
A
L
Step 2: Secure left arm (1) to assembl ed chair back (3) with 2 screws (C) by
using allen wrench(L). Do not tigh ten all screws now. Then, secur e seat panel
(4) to assembled left arm (1) with 2 scr ews (A) by using allen wrench (L). Do
3
not fully tighten now.
4
C
L
3
7
4
8
L
L
L
C
C
7
C
8
1
C
L
3
L
4
C
8
7
C
L
2
Inside of chair back
Step 3: Insert seat panel (8) into the t wo holes on chair back (7), then secure
them with 2 screws (C) by using allen wr ench (L). Do not tighten all screws
now.
2
7
C
L
8
2
L
A
C
L
L
Step 4: Secure right arm (2) to assemb led chair back (7) with 2 screws (C) by
using allen wrench (L). Then, secure seat panel (8) to assembled r ight arm
(2) with 2 screws (A) by using allen wre nch (L). Do not fully tighten now.
8
A
Step 5: Connect and secure both half c hair together with 4 screws (C) by
using allen wrench (L), two at the cha ir back and two at the front seat panel.
21
20
STEP 6: Please veri fy the al ignment and adjus t, full y tight en all the scr ews now. Then p ut
seat cushion ( 20) and b ack cushion (21) on t he chai r, your chair is assem bled.
5
20
21
6
6
Loading...