Winston Porter MCRR6522 Assembly Instruction

BAR STOOL

CAUTION: You must read this before you proceed.

CAUTION : This Barstool is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Barstool and to prevent damage to the Barstool, two
adults may be needed to execute this action.

Page 1 of 7

DescriptionPictureNo. Qty

B

1

Backrest Panel

A1

A2

Left Leg Panel

Right Leg Panel

1

1

C

D

① 11

②

Seat Panel

Leg Connector

Bolt (M6x45mm)

Allen Key

1

2

QtyPicture DescriptionNo.

1

Page 2 of 7

Read instructions, cover to cover.

Before Beginning Assembly:

Have 2 adults on hand for assembly.

Do not assemble on flooring or carpet.

Assemble on a clean non-marring surface (packing foam).

Save all packaging until finished.

OVERVIEW

Left Leg Panel
(A1)

Leg Connector
(D)

Backrest Panel (B)

Seat Panel (C)

Right Leg Panel
(A2)

Leg Connector (D)

This Bar Stool has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Bar Stool parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise youself with the parts and steps before
assembly.

Page 3 of 7

Step 1

Unpack and place all parts on a clean, non-marring surface.

Step 2

Step 3

Iron dowel

Step 2.1

Iron dowel

Step 3.1

3.1) Insert 2 prefixed iron dowels of Seat Panel (C) into housings of Right Leg Panel (A2).

3.2) Secure Seat Panel (C) to Right Leg Panel (A2) by using 2 Bolts (①) with Allen Key(②).
Do not fully tigthen Bolts.

Page 4 of 7

Step 4

Attached Left Leg Panel (A1) to frame in step 4 then secure Left Leg Panel (A1) to Backrest

A2

2

4.1) Insert prefixed iron dowel of Leg Connector (D) into housing of Right Leg Panel (A2).

4.2) Secure Leg Connector (D) to Right Leg Panel (A2) by using Bolt (①)

Do not fully tigthen Bolt.

Repeat the same process with the other Leg Connector (D)

with Allen Key(②).

Step 5

With the assistance of an adult helper, turn the Barstool 90 degree.

Panel (B) by using long Bolt (②), Seat Panel (C ) and Leg Connectores (D) by using Short Bolts
(①) and Allen Key (③)

Do not fully tighten Bolts

Page 5 of 7

Step 6

This Drop Test will help to ensure that all the Bolts and gaps reach full alignment status.

If wobble

Test again

30cm­50cm

Place the Barstool right side up on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Barstool some 30cm to 50cm height from the ground.
Keep your feet and toes well away from the drop zone.

Drop the Barstool freely and vertically with all four legs, hitting the ground at the same time.
This Drop Test will help to ensure that all the Bolts and gaps reach full alignment status.

Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, proceed to tighten all the Bolts.

When tightening these bolts, tighten sequentially.
Do not tighten any Bolt fully and then move towards the next one.
This could cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute the same drop tests.
If the Barstool is not stable it could lead to damage to the product.

Step 7

Inspect the Barstool and make sure all parts are connected.
Your Barstool is ready for use.

This Barstool can only be used on a flat, level surface.

Page 6 of 7