Page 1
Caution : You must read this before you proceed
DINING CHAIR
CAUTION: This Chair is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Chair and to prevent damage to the Chair, two adults
are needed to execute this action.
Page 1 of 7
Page 2
Label Picture Description QTY
Allen Key 2
4
A Left Leg 1
B Right Leg 1
C Backrest 1
D Seat Panel 1
E Seat Cushion 1
Label Picture Description QTY
1
2
Screw (M6x45mm) 7
Bolt (M6x40mm) 3
3
Sleeve Nut (M6x13mm) 3
Page 2 of 7
Page 3
Before Beginning Assembly:
Seat Cushion
(E)
(B)
Seat Panel
(D)
Backres
t (C)
To give you an overview of the Chair parts, the above picture is to help you put the
OVERVIEW
Left Leg
Right Leg
(A)
FRONT FACING
This Chair has multiple parts and may require up to some 30 minutes to assemble.
various parts into perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
Page 3 of 7
Page 4
Step 1
①
③
④
B
D
4
③ ④
Unpack and place all parts on a clean, non-marring surface.
Step 2
Step 2.2
3
4
4
2
Step 2.1
1
2.1) Position Right Leg(B) and Seat Panel(D) as shown in picture
above. Secure Right Leg(B) and Seat Panel(D) using Screw(
Allen Key(④).
2.2) Secure Right Leg(B) and Seat Panel(D) using Bolt(②), and
Sleeve Nut(
Only loosely tighten the Screws and Bolts.
) with Allen Key(
).
) with
Page 4 of 7
Page 5
Step 3
Repeat the same process from the previous step to attach the Left Leg(A).
C
enable the Backrest(C) to be slotted into position.
4
A
4
1
2
3
4
With the help of your partner, turn the Chair over and rest on Right Leg(B).
Only loosely tighten the Screws and Bolts.
Step 4
1
4
Place Backrest(C) into the housing of Left Leg(A) and Right Leg(B)
You may need to apply a little pressure to the Legs, pushing outwards, to
Secure Backrest(C) and Legs using Screws(①) with Allen Key(④)
Only loosely tighten the Screws.
Page 5 of 7
Page 6
Step 5
Test again for evenness on a LEVEL SURFACE.
Place Seat Cushion(C) on to the seat of the Chair using the velcro straps as shown
If wobble
Test again
30CM~50CM
Place the Chair right side up on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Chair to some 30cm to 50cm height from the ground.
Keep your feet and toes well away from the drop zone.
Drop the Chair freely and vertically with the four legs, hitting the ground, at the same time.
This Drop Test will help to ensure that all the Bolts, Screws and gaps all reach full
alignment status.
If no wobbles are found, proceed to tighten all the Screws, and Bolts.
CAUTION: When tightening the Screws, and Bolts tighten sequentially. DO NOT
tighten any Bolt, or Screw fully and then move towards the next one. This could
cause the frame to warp.
If there are still wobbles, loosen the Screws and Bolts and execute this same drop tests.
If the Chair is not stable, it could lead to damage to the product.
Step 6
Inspect the Chair and make sure all parts are adequately connected.
above.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Page 6 of 7
Page 7
Page 7 of 7
Loading...