Winny OD15061, HJ1009B Instruction Manual

Important Precautions

1. This model mainly applies to swimming pool with flat floor

2. Make sure that your local voltage is compatible with the device.

3. In order to prevent severe damage to the cleaner, never power on the unit when it is

outside of the swimming pool.

4. Make sure the electrical outlet is grounded. It is strongly advised to protect the electrical

line on which the robot is connected by a differential of 30 milliamperes of type AC.

5. Do not operate the cleaner when people are in the pool.

6. Before power on, make sure the cable is fully released to avoid any winding, which could

affect the cleaner’s performance or cause damage.

7. The filter bags should be cleaned every time you use the unit. This will prevent the dirty

filter bags affecting the normal operation of the cleaner.

8. The cleaner should be stored in a cool and ventilated place, away from direct sunlight,

when not in use.

9. The power supply unit should be placed in a shaded area. In order to avoid overheating

and the potential damage of components, never cover the power supply unit.

10. Only authorized after sales service personnel should open the cleaner’s motor assembly

and power supply unit, otherwise the warranty will be invalidated.

11. Do not uncover the protective film which is sticked on the operating panel.

12. Do not use the cleaner beyond the working environment/conditions stated in this manual.

13. Close the filtering system of your pool when use this cleaner.

14. The file must be disconnected from the wall outlet before cleaning or repair.

15. If the power cable is damaged, it must be replaced by the manufacturer, its service agent

or similar qualified person in order to avoid a hazard.

16. This appliance can be used by children aged from 8 years and above and person with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

1

17. CAUTION – The control box of the appliance must be fixed to the ground or the wall

securely. Never operate the unit without fixing the control box first.

18. CAUTION – The control box must be fixed at a minimum distance of 3.5m from the edge

of the swimming pool.

19. The cleaner is only to be used with the power supply unit provided with the appliance

20. The unit should be operated only under low safety voltage corresponding to the marking

of the appliance.

Note

1. Putting into or lifting out from pool with the cleaner bottom toward the wall to avoid any

possible scratch to the pool surface.

2. Please store the cleaner in flat place, the cleaner body should not touch any hard

article to avoid possible damage.

3. Do not press into or lift out the filter cartridge when install or take off it to avoid any damage to

the chassis.

Do not lift both sides of the filter cartridge Do not lift both sides of the cartridge

at the same time at the same time.

2

Contents

Ⅰ. Introduction…………………………………………………………………………………..·P. 4

Ⅱ. Safety…………………………………………………………………………………………..P. 4

Ⅲ. Specifications…………………………………………………………………………………P. 4

Ⅳ. Cleaner Structure……………………………………………………………………………..P. 5

Ⅴ. Operation Instructions……………………………………………………………………….P. 6

Ⅵ. Trouble Shooting……………………………………………………………………………...P. 15

Ⅶ. Packing List…………………………………………………………………………………….P. 16

Ⅷ Warranty…………………………………………………………………………………………P. 16

3

Ⅰ. Introduction:

The automatic swimming pool floor cleaner OD15061/HJ1009B is a new type of highly efficient

swimming pool cleaning equipment. Through its advanced computer controlled program, it can

clean the pool floor automatically without draining pool water. At the same time, it filters the pool

water and gets rid of suspended particles and sediments.

For safe operation, the cleaner works on 24V direct current.

Please read this instruction manual carefully before use.

. Safety:Ⅱ

1, Position requirement of power supply unit：Refer to item 9 and 11 in “Important Precautions”.

2, Requirement of power: Refer to item 3 in “Important Precautions”.

Before connecting the cleaner to power, please check that the local voltage and

frequency (hertz) correspond to that of the power supply unit.

Ⅲ. Specifications:

1. Rated input voltage and frequency: 230V/50Hz

2. Output Voltage: DC24V

3. Rated input and output power: 150W/120W

4. Working cycle: 1h/1.5h/2h/2.5h

5. Cable length: 13m

6. Maximum cleaning area: 150m²

7. Filtering capacity: 15m³/h

8. Filtering capability: 150µm

9. Water temperature of use: 10°C - 35°C

10. Creeping speed: 15-18m/min

11. IP Grade：Cleaner-IPX8 Power supply unit-IPX4

12. Working temperature: 10°C - 40°C

4

13. Pool depth: 2.5m

Optional

. Cleaner Structure

3

1

4

2

Fig.4-1

Assembly the cleaner according to above structure

5

. Operation Instruction

5.1 Cable connection

5.1.1 Plug the cable line into the socket on the power supply unit (note: make sure to plug it

in the correct direction and position), and fasten the nuts on both sides of the plug.

Match point

Fig. 5-1

5.1.2 Connect the plug with power

Turn round this part for

locking or loosen

Fig.5-2

6