Page 1
pakedgedevice&software inc
SE-8P
8 Port Gigabit Unmanaged Switch with 8 ports PoE or
4 ports PoE+
User Manual - Version 1.0
Page 2
FCC Certifications
This Equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to the EMC
Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC, and the
RoHS Directive 2011/65/EU.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written
consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2015, All Rights Reserved.
Page 3
1
Unpacking Information
Thank you for purchasing the Pakedge Device & Software SE-8P gigabit switch.
Before installation, please verify that your package contains the following items.
1. One 8-Port Gigabit Ethernet Switch with 8-port PoE+
2. One AC power cord
3. Rack-mount brackets and screws (included, optional use)
4. User Manual
Introduction
General Description
The SE-8P provides 8*10/100/1000Mbps Gigabit ports with 8-port PoE+, making
it an excellent choice for a fast, cost effective and reliable networking
infrastructure. The store-and-forward architecture filters errors and forwards
packets in a non-blocking environment. Flow control ensures the accuracy of the
data transmitted. The PoE+ on the SE-8P supplies power for connected devices
that need it. Over current protection and circuit shorting protection are also
supported.
The switch was designed for easy installation and maintenance. It supports the
Nway auto-negotiation protocol that detects networking speed (10/100/1000
Mbps) and duplex modes (Full/Half) automatically. Auto-MDI/MDI-X function
alleviates the need for crossover cables. Also, rich diagnostic LEDs are provided
for real-time connection status information.
Key Features
Complies with 10BASE-T specifications of the IEEE802.3 standard
Complies with 100BASE-TX specifications of the IEEE802.3u standard
Complies with 1000BASE-T specifications of the IEEE802.3ab standard
Complies with IEEE 802.3af/at PoE standard
Supports 31.5W maximum per PoE port
Supports over current protection and circuit shorting protection
8* 10/100/1000Mbps RJ-45 Nway ports
Supports NWay protocol for speed (10/100/1000Mbps) and duplex mode
(Half/Full) auto-detection
Supports MDI/MDI-X auto crossover
Supports full and half duplex operation on all ports
Wire-speed packet filtering and forwarding rate
Store-and-forward architecture filters fragment & CRC error packets
Supports 8K MAC address entries in who le system
Page 4
2
128K bytes buffer memory
LED
Status
Operation
Steady Blue
The switch is powered on
Off
The switch is powered off
Blinking Red
There is a loop
LED
Status
Operation
Steady Blue
Valid port connection.
Valid port connection and there is data
transmitting/ receiving
Port disconnected or the port is connected at 10
Mbps or 100 Mbps
A PoE compliant devices is connected to the
port
No PoE complaint device is connected to the
port
Supports automatic loop detection and isolation
Supports 9K bytes Jumbo Frames
Supports extensive LED indicators for network diagnostics
Internal power adapter
FCC, CE and LVD
The Front Panel
The front panel consists of LED indicators. For detailed LED definition, please
refer to the next paragraph.
LEDs Definition
System LED
PWR
LOOP
Port LEDs
LINK/ACT
PoE
Off
Blinking Blue
Off
Steady Blue
Off
There is no loop
Page 5
3
Power Receptacle
To be compatible with the varying electric service standards around the world, the
switch comes with a power supply which can operate from 100 to 240VAC,
50/60Hz. Please make sure that your outlet standard is within this range.
To power on the switch, plug the female end of the power cord firmly into the
receptacle of the switch and the other end i nto an el ec tric ser vice o utl et. Af ter th e
power cord installation, toggle the ON/OFF switch into the ON position and please
check if the power LED is illuminated to ensure normal operations.
Rear Panel
Installation
This switch can be pl aced on your desktop directly, or mounted in a rack. The
installation is simple. Users can utilize all the features of the switch just by
attaching the appropriate cables and turning the power on.
Before installing the switch, we strongly recommend:
1. The switch is placed in a w ell ventilated environment. A minimum of 25mm
(1 inch) space around the unit is recommended.
2. The switch and the relevant components are away from electrical noise
sources such as radios, transmitters and broadband amplifiers
3. The switch is not placed in a high humidity or moist environment.
Desktop Installation
1. Attach the provided rubber feet to the bottom of the switch to keep the
switch from slipping. The recommend position is square-marked.
2. Install the switch on a level surface that can s upport the weight of the unit
and the relevant components.
3. Plug the switch with the female end of the pr ovided power cord and plug
the male end into the power outlet.
Page 6
4
Media
Speed
Wiring
10/100/1000Mbps copper
10Mbps
Category 3,4,5 UTP/STP
100Mbps
Category 5 UTP/STP
1000Mbps
Category 5,5e UTP/STP
Media
Speed
Duplex Mode
10/100/1000Mbps(copper)
10Mbps
Full Duplex
Half Duplex
100Mbps
Full Duplex
Half Duplex
1000Mbps
Full Duplex
Rack-mount Installation
Rack mounting facilitates an orderly installation when a series of networking
devices are installed. The switch is supplied with rack mounting brackets and
screws
Procedures to Rack-Mount the Switch:
1. Disconnect all the cables from the switch before continuing.
2. Place the unit on a hard, flat surface with the front facing you.
3. Place a mounti ng br ac ket over the mounting holes on one s i de of the
unit.
4. Insert the screws and fully tighten with a suitable screwdriver.
5. Repeat the two previous steps for the other side of the unit.
6. Insert the unit into the rack and secure with suitable screws.
7. Reconnect all the cables.
Network Cables Installation
1. Crossover or straight-through cable: All the ports on the switch support
Auto-MDI/MDI-X functionality. Both straight-through or crossover cables
can be used to connec t the switch wit h PCs as well as other devices like
switches, hubs or router.
Category 3, 4, 5 or 5e UTP/STP cable: To make a valid connection and
2.
obtain the optimal performance use th e appropriate cabl es correspond ing
to different transmitting/receiving speed. To choose a suitable cable,
please refer to the following table.
Port Operation
The auto-negotiatio n feature allows ports running at one of the following
operation modes:
1000Mbps Fiber (Mini GBIC required)
Page 7
5
IEEE802.3 10BASE-T
IEEE 802.3af/at PoE standard (DTE power via MDI)
8*10/100/1000 Mbps auto MDI/MDI-X RJ-45 switching ports
15.4W(af) x 8 Ports
Cable
RJ-45 (10BASE-T): Category 3,4,5 UTP/STP
RJ-45 (1000BASE-T): Category 5,5e or enhanced UTP/STP
Transmission
1 * power LED
1 * loop LED
8K MAC entries
128K bytes Buffer Memory
Emission
Safety
Operating
Operating
Internal power supply
100-240V/47-63 Hz universal input
Dimensions &
Product Specifications
Standard
Interface
Connections
Mode
LED indications
Memory
Temperature
IEEE802.3u 100BASE-TX
IEEE802.3x full-duplex flow control
IEEE802.3ab 1000BASE-T
Supports 136W Max;
Full load:
31.5W(at) x 4 Ports
RJ-45 (100BASE-TX): Category 5 UTP/STP
10/100Mbps Full-duplex, Half-duplex
1000Mbps Full-duplex
8 * Link/ACT LEDS
8 * PoE LEDS
9216 bytes jumbo packet length
FCC & CE
LVD
00 ~ 400C (320 ~ 1040F)
Humidity
Power Supply
Weight
10% - 90%(non-condensing)
12.68 x 7.31 x 1.75
4.3 lbs.
Page 8
6
Technical Support
Please visit our website for up-to-date support information:
Website: www.pakedge.com
Email: support@pakedge.com
CONTACT INFORMATION:
Pakedge Device & Software Inc.
3847 Breakwater Avenue
Hayward, CA 94545-3606
USA
877-274-6100
© Pakedge Device & Software Inc. 2015 – All Rights Reserved
Loading...