Winning Home WH100028 Installation Guide

TRIAD INSTALLATION GUIDE - TRIAD ONE, SINGLE ZONE HIGH-RESOLUTION STREAMING AMPLIFIER

INTRODUCTION

The Triad One is a single-zone, high-resolution streaming amplifier and the
easy way to add music into any room of a Control4-enabled home without
the need to pull wire back to a central location. The Triad One supports
high-resolution audio playback, up to 192 kHz / 24 bit, with a built-in
amplifier boasting an impressive 105 dB signal-to-noise ratio and 100 watts
per channel—enabling incredible sound in any room. Also included is a
built-in 10-band parametric EQ delivering exceptional sound output and
room optimization.

The Triad One is also a great alternative to an AVR in a bedroom, kitchen,
or other location when surround sound is not a requirement. Not only
does the Triad One have digital and analog audio inputs to take the audio
output from a TV to power a soundbar, it has two IR outputs to control the
TV and another local source, if needed.

A line-level subwoofer output rounds out the system for deep bass when
connected to a powered subwoofer. The Triad One is available in white and
black, can be placed horizontally or vertically, and can be installed on a
bookshelf, in a rack, or mounted behind a TV.

WARNINGS

WARNING! To reduce the risk of electrical shock, do not expose
this apparatus to rain or moisture.

AVERTISSEMENT ! Pour réduire le risque de choc électrique,
n’exposez pas cet appareil à la pluie ou à l’humidité.

WARNING! Do not expose the apparatus to dripping or splashing.
Do not place objects filled with liquids near the apparatus.

AVERTISSEMENT ! N’exposez pas l’appareil aux éclaboussures et
éloignez de toutes substances liquides. Ne placez pas les objets
contenant du liquides près de l’appareil.

IMPORTANT! Using this product in a manner other than outlined
in this document voids your warranty. Further, Control4 is not
liable for any damage incurred with the misuse of this product. See
“Warranty.”

IMPORTANT ! Employer ce produit en quelque sorte autre que
décrit dans ce document vide votre garantie. De plus, Control4
n’est pas responsable d’aucun dommage encouru avec l’abus de ce
produit. Voyez que « Warranty. »

FEATURES

• Add a high-resolution, amplified audio zone to any Control4 system

• Built-in streaming music services synchronized with EA controllers

• Network control of audio and volume over a wired or WiFi connection

• Analog and digital audio inputs support audio resolutions up to
192 kHz / 24 bit

• Volume, bass, treble, 10-band parametric EQ, balance, loudness, and
mono summing

• Input gain for analog source input

• Audio sensing supports programmable events based on the presence
of audio

• Built-in EQ presets for Triad speakers

• Supports native Control4 streaming services including Pandora,
Spotify, TIDAL, Napster, Sirius XM, Deezer, and iHeartradio

• Supports built-in Control4 digital media playback including My Music,
ShairBridge, and DLNA

SUPPORTED MODELS

• TS-SAMP-100-BL Triad One, Single Zone, High-Resolution Streaming
Amplifier in Black

• TS-SAMP-100-WH Triad One, Single Zone, High-Resolution Streaming
Amplifier in White

BOX CONTENTS

• Triad One

• AC power cord

• Phoenix connector for speaker wires

• Rear cover

FRONT AND REAR PANEL DESCRIPTION

REAR PANEL

E

A

B

A

A ETHERNET—RJ-45 port for network connection. Used for device control,

device configuration, and digital audio streaming.

B

B USB—USB 2.0 port. Used for local media file storage.

C

C ID—Button used to identify the device in a Control4 system.

D

D FACTORY RESTORE—Button used to reset the amplifier to factory

settings.

E

E IR—Two 3.5 mm IR ports. Used to control devices such as a TV or local

AVR in a Control4 system.

F

F AUDIO IN—Two audio inputs. One RCA stereo input, one

S/PDIF or digital coax input. Digital inputs accept stereo PCM audio
only.

G

G AUDIO OUT— Line-level audio output. One stereo RCA connection and

one mono RCA connection for subwoofer out.

H

H SPEAKER OUT—Phoenix-style connector for speakers.

I

I Power plug port—AC power connection 100V – 240V,

50 - 60 Hz.

C

D

F G

FRONT PANEL

J

J Status LED—Logo LED shows power, boot, and device

status.

H I

IMPORTANT! To avoid generating excessive heat, do not stack

amplifiers on top of each other or other equipment.

IMPORTANT ! Pour éviter de produire de la chaleur excessive, ne
pas disposer les amplificateurs, ou tout autre équipement, les uns
sur les autres.

www.control4.com | 1-888-400-4072 | DOC-00287-A 2017-08-28 DH

J

TRIAD INSTALLATION GUIDE - TRIAD ONE, SINGLE ZONE HIGH-RESOLUTION STREAMING AMPLIFIER

INSTALLING THE TRIAD ONE

MOUNTING OPTIONS

The Triad One can be mounted in a rack for structured, distributed audio,
or in the wall for a minimal look when mounting behind a TV. Mounting kits
are sold separately to accomodate these installations.

• Triad One Rack-Mount Kit (TS-AMP1RM-BL)

• Multi-Purpose In-Wall Box (C4-MPIWB-BL)

The Triad One Rack-Mount Kit Installation Guide (triadspkrs.co/one-rmk)
and the Control4 Multi-Purpose In-Wall Box Installation Guide
(ctrl4.co/inwallbox-ig) describe how to use each mounting kit.

Caution! For optimal heat dissipation, the
Triad One must not be placed upside down. The
correct position when installed vertically has the
Triad logo triangle on the bottom pointing up.

CONNECTING USB STORAGE AND IR CABLES

You can connect USB storage to your Triad One to have access to stored
music files for playback within your Control4 system. Playback of AAC,
AIFF, ALAC, FLAC, M4A, MP2, MP3, MP4/M4A, Ogg Vorbis, PCM, WAV, and
WMA files are supported. See the Composer Pro User Guide
(ctrl4.co/cpro-ug) for help on adding digital media files to your system.

1 Connect a USB flash drive or externally-powered USB hard drive to the

USB port.

2 Set up digital media in the Control4 project using Composer Pro.

The Triad One has two IR emitter ports to control local devices, such as a
TV or media player.

1 Connect an IR emitter (sold separately) into an IR port on the amp.

2 Remove the adhesive backing from the emitter (round) end of the IR

emitter and ax it to the device to be controlled over the IR receiver
on the device.

3 Make connections in Composer Pro from the Triad One to the drivers

for the connected devices. See the Composer Pro User Guide
(ctrl4.co/cpro-ug) for more help.

TRIAD ONE

CONNECTING A SINGLE ZONE IN A CONTROL4 SYSTEM

As part of a Control4 home automation system, the Triad One can control
the local devices in a room and can deliver streaming, amplified audio to
the room. The system must have a Control4 controller, such as an EA-5, in
the project.

1 Connect audio sources (outputs from a TV or other audio source) to

the AUDIO IN.

2 Connect the speakers to the wiring connector and connect to the

SPEAKER OUT output.

3 (Optional) Connect an active (self-powered) subwoofer to the SUB/

MONO OUT.

4 (Optional) Connect IR emitters to the IR outputs to control local

devices.

IMPORTANT! The speaker outputs of the Triad One must not be
connected together or to any other common signal. In particular,
the L - and R - terminals should not be joined together. Doing so
will result in a fault condition and the Triad One may shut down or
not work as designed.

External audio source

REAR COVER

The Triad One comes with an optional Rear Cover to assist with cable
management, especially when the Triad One is installed on a bookshelf or
on a piece of furniture in the room.

To attach the rear cover, push the bottom
of the cover on first, then snap in the top.

To release the rear cover, press the tab
under the top of the cover and pull away
from the Triad One

2

1

CONNECTING THE TRIAD ONE TO ETHERNET AND POWER

1 Plug the Ethernet CAT5E/6 cable from a local network connection into

the ETHERNET port.

Ethernet

cable

USB

IR cables

Power

cable

CONNECTING AUDIO TO THE TRIAD ONE

Both physical audio connections and connections in software are required
to control, navigate, and use the Triad One as designed. Use Composer Pro
to add the driver to the desired room and set up the connections. See the
Composer Pro User Guide (ctrl4.co/cpro-ug) for details.

Connect the physical connections to your Triad One from your other
audio equipment using the examples below:

TRIAD ONE

IR to TV

Audio
out from
TV

Note: The Triad One can be configured for WiFi, but must be
connected to a wired connection first. See the Composer Pro User
Guide (ctrl4.co/cpro-ug) for more details.

2 Connect the provided power cable from the back of the Triad One to

the power outlet. When the power cable is connected, the amp should
power up and the Status LED on the front should light up.

www.control4.com | 1-888-400-4072 | DOC-00287-A 2017-08-28 DH

• Connecting a single zone in a Control4 system

• Adding a streaming audio zone with the Triad One

• Adding analog and streaming audio zones with the Triad One

• Adding an outdoor zone with the Triad One

Triad On-Wall LCR Soundbar + In-Room Omni Sub

AC POWER:

100-240 V~

60/50 Hz, 0.5 A

WIFI 1 WIFI 2

SERIAL 2

USB E-SATA

FACTORY

RESET

OUT

COMNCNO

COMNCNO

COMNCNO

COMNCNO

+12

SIG

GND

+12

SIG

GND

+12

SIG

GND

+12

SIG

GND

3 5 7

ZIGBEE

SERIAL 1

ID

4 6 8

IN 1 IN 2 OUT 1 OUT 2

1 2 3 4

1/ 3

IN 1 OUT 1

IN 2 OUT 2

DIGITAL AUDIO ANALOG AUDIO

GIGABIT SWITCH

ETHERNET IN

IR / SERIAL

2/ 4

ALL

LINK TO GLOBAL INPUT

POWER MODE

ON
12V
AUDIO

2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN

R

L

GLOBAL OUT

GLOBAL IN

L

R

CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP

AC POWER 100V-240V ~50-60Hz 105W

FUSE RATING T6.3A_H 250V

2 3 4 5 6 7 81

12V

TRIGGER

OUT

IN

LRL R L

R L R

L R L R L R L R

ZONE

OUTPUTS

1

5 63748

BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE

2

External audio sources

EA-5

24x24 AMS

Zones 1-8

8 pairs

Triad

In-Ceiling

speakers

Speaker wires

RCA connections to amplifier 1

Amplifier 1

RCA connections to amplifier 2

to amplier 2

ALL

LINK TO GLOBAL INPUT

POWER MODE

ON
12V
AUDIO

2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN

R

L

GLOBAL OUT

GLOBAL IN

L

R

CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP

AC POWER 100V-240V ~50-60Hz 105W

FUSE RATING T6.3A_H 250V

2 3 4 5 6 7 81

12V

TRIGGER

OUT

IN

LRL R L

R L R

L R L R L R L R

ZONE

OUTPUTS

1

5 63748

BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE

2

RCA connections to Triad One amps

8-ZONE
POWER AMP

AC POWER:

100-240 V~

60/50 Hz, 0.5 A

WIFI 1 WIFI 2

SERIAL 2

USB E-SATA

FACTORY

RESET

OUT

COMNCNO

COMNCNO

COMNCNO

COMNCNO

+12

SIG

GND

+12

SIG

GND

+12

SIG

GND

+12

SIG

GND

3 5 7

ZIGBEE

SERIAL 1

ID

4 6 8

IN 1 IN 2 OUT 1 OUT 2

1 2 3 4

1/ 3

IN 1 OUT 1

IN 2 OUT 2

DIGITAL AUDIO ANALOG AUDIO

GIGABIT SWITCH

ETHERNET IN

IR / SERIAL

2/ 4

ALL

LINK TO GLOBAL INPUT

POWER MODE

ON
12V
AUDIO

2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN

R

L

GLOBAL OUT

GLOBAL IN

L

R

CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP

AC POWER 100V-240V ~50-60Hz 105W

FUSE RATING T6.3A_H 250V

2 3 4 5 6 7 81

12V

TRIGGER

OUT

IN

LRL R L

R L R

L R L R L R L R

ZONE

OUTPUTS

1

5 63748

BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE

2

EA-5

24x24 AMS

Amplifier 1

TRIAD INSTALLATION GUIDE - TRIAD ONE, SINGLE ZONE HIGH-RESOLUTION STREAMING AMPLIFIER

ADDING A STREAMING AUDIO ZONE WITH THE TRIAD ONE

ADDING ANALOG AND STREAMING AUDIO ZONES WITH THE TRIAD ONE

An extra audio zone can be added to the Triad Audio Matrix Switch using
a Triad One. In this example, the Triad One streams all sources that are
connected to the input of a Control4 controller (or another Triad One)
and, also, the Triad One generates its own digital media streams (Control4
native streaming services like Pandora and TIDAL and other digital media
like My Music).

1 Connect external audio sources to the analog audio and digital audio

(coax) inputs of the controller.

2 Connect the rest of the audio system as described in the Triad

8x8/24x24 Audio Matrix Switch Installation Guide

(triadspkrs.co/ams-ig).

3 Connect the Triad One to power and network (can be configured WiFi)

as described in this guide.

4 Connect speakers to the SPEAKER OUT connection and connect a

subwoofer to the SUB/ MONO OUT connection (if desired).

5 (Optional) Audio sources (TV, media player, or other sources) may

also be connected to the Triad One that shared over the network and
listened to in any other zone in the system. Connect the audio out from
the source to the one of the AUDIO IN inputs.

External audio sources into controller

If an extra audio zone is needed, the Triad One can be used as a single-zone amplifier behind an audio matrix switch to provide another zone of audio with
access to the analog audio sources in the audio matrix switch, and an additional digital media audio stream for the new zone.

1 Connect external audio sources to the ANALOG AUDIO INPUT of the audio matrix switch.

2 Connect audio sources (outputs from a Control4 controller, audio streaming devices, tuners, etc.) to the ANALOG AUDIO INPUT and DIGITAL AUDIO

INPUT jacks of the audio matrix switch.

3 Connect the ANALOG AUDIO OUTPUT jacks and 12V trigger cables from the Triad 24x24 Audio Matrix Switch to Triad Power Amplifiers as described in

the Triad 8x8/24x24 Audio Matrix Switch Installation Guide (triadspkrs.co/ams-ig)

4 Connect the ANALOG AUDIO OUTPUT 17 and 18 to the AUDIO IN inputs of the Triad One amplifiers.

5 Connect the Triad One amplifiers to power and network (can be configured WiFi) as described in this guide.

6 Connect speakers to the SPEAKER OUT connections and connect a subwoofer to the SUB/MONO OUT connection (if desired).

7 (Optional) Audio sources (TV, media player, or other sources) may also be connected to the Triad One that shared over the network and listened to in

any other zone in the system. Connect the audio out from the source to the one of the AUDIO IN inputs.

Connections from matrix switch to amplifier 2

External audio sources

8-ZONE
POWER AMP

Amplifier 2

EA-5

8x8 AMS

TRIAD ONE

1 2 3 4

COMNCNO

COMNCNO

COMNCNO

COMNCNO

AC POWER:

WIFI 1 WIFI 2

100-240 V~

60/50 Hz, 0.5 A

+12

+12

+12

+12

SIG

SIG

SIG

SIG

GND

GND

GND

GND

GIGABIT SWITCH

ETHERNET IN

USB E-SATA

SERIAL 1

SERIAL 2

3 5 7

1/ 3

OUT

ID

FACTORY

RESET

2/ 4

4 6 8

IR / SERIAL

IN 1 OUT 1

IN 1 IN 2 OUT 1 OUT 2

IN 2 OUT 2

DIGITAL AUDIO ANALOG AUDIO

ZIGBEE

to amplier 2

8-ZONE

RCA connections to amplifier 2

RCA connections to amplifier 1

RCA connections to Triad One amps

Zones 9-16

Speaker wires

8 pairs

Triad

In-Ceiling

speakers

POWER AMP

RCA connections to amplifier

for zones 1-8

Zone 9 Triad
In-Room
Omni Sub +
1 pair speakers

Zones 1-8

8 pairs

Triad

In-Ceiling

speakers

Speaker wires

Connection from audio
matrix switch output 17

TRIAD ONE

TRIAD ONE

Connection from audio
matrix switch output 18

Zone 17

Triad In-Room

Omni Sub +

1 pair speakers

Zone 18

Triad In-Room

Omni Sub +

1 pair speakers

www.control4.com | 1-888-400-4072 | DOC-00287-A 2017-08-28 DH

TRIAD INSTALLATION GUIDE - TRIAD ONE, SINGLE ZONE HIGH-RESOLUTION STREAMING AMPLIFIER

TRIAD ONE

OD26 Outdoor

8x8 AMS

SERIAL NUMBERSERIAL NUMB

ER

BAR CODE

100-240

V

~

50/60Hz 350

W

1718 W

. MISHAWAKA RD.

ELKHAR

T IN 46517 US

A

W

ARNING

T

O REDUCE THE RISK

OF FIRE OF ELECTRICAL SHOCK, DO

NOT EXPOSE THIS EQUIPMENT T

O

R

AIN OR MOISTURE.

AVER

TISSEMENT

C

AHIER D’INSTRUCTIONS.

APPARATET MA

TILKOPLES JORDET

STIKKONTAKT

.

APPARA

TEN SKALL ANSLUTAS TILL

JORDA

T UTTAG.

LAITE ON LIITETTÄVÄ

SUOJAKOSKET

TIMILLA

V

ARUSTET

TUUN PISTORASIAAN.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVER

TISSEMENT:

RISQUE DE CHOC

CLASS 2 OUTPUT WIRING PERMITTED.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERA

TION IS SUBJECT TO

THE FOLLOWING CONDITIONS.

INTERFERENCE.

W

ARNING

OUTPUT

BLU linkINOU

T

CROWN CDi 2|600

AC POWER:

100-240 V~

60/50 Hz, 0.5 A

WIFI 1 WIFI 2

SERIAL 2

USB E-SATA

FACTORY

RESET

OUT

COMNCNO

COMNCNO

COMNCNO

COMNCNO

+12

SIG

GND

+12

SIG

GND

+12

SIG

GND

+12

SIG

GND

3 5 7

ZIGBEE

SERIAL 1

ID

4 6 8

IN 1 IN 2 OUT 1 OUT 2

1 2 3 4

1/ 3

IN 1 OUT 1

IN 2 OUT 2

DIGITAL AUDIO ANALOG AUDIO

GIGABIT SWITCH

ETHERNET IN

IR / SERIAL

2/ 4

EA-5

ADDING AN OUTDOOR ZONE WITH THE TRIAD ONE

An outdoor audio zone can be added to the system using the Triad One
and a high-power amp for the subwoofer or a garden array (if desired).

1 Connect external audio sources to the analog audio and digital audio

(coax) inputs of the controller (to be able to stream those sources to
the Triad One).

2 Connect the rest of the system as normal.

3 Connect the SUB/MONO OUT from the Triad One to the Crown

amplifier for the garden array.

4 Connect Triad OD26 outdoor speakers to the SPEAKER OUT of the

Triad One and connect a Triad Garden Array GA10 Outdoor Sub
and GA4 Sats to the Crown amp as shown in Triad Garden Array
documentation (triadspkrs.co/gardenarray).

OF THIS PLUG MUST BE MAINTAI NED

ATTENTION - POUR RÉDUIRE
ÉLECTRIQUE LA FICHE CENTR
BRANCHÉE POUR MAINTENIR

CAUTION - TO REDUCE THE RISK OF ELECTRIC

SHOCK, GROUNDING OF THE CENTER PIN

LE RISQUE DE CHOC
ALE LA PRISE DOIT ÊTRE

LA MISE À LA TERRE

External audio sources into controller

RCA connections to amplifier

for zones 1-8

Zone 9 Triad

speakers +
Garden Array

ETHERNET

100Mb

GPIO/AUX

7

45IN6

8

AMP STATUS

SLEEP

+3.3V

OUTPUT
WIRING

BRIDGE

DUALDUAL

2 1

ACT

3

OUT12IN

2 1

INPUT

TROUBLESHOOTING

RESETTING THE TRIAD ONE

• Network reset—Remove the power cord to power cycle the device.
Hold the ID button while you replace the power cord to power on the
Triad One. Hold the ID button until the Status LED turns solid orange.

• Factory restore—Press and hold the FACTORY RESTORE button for
five seconds to restore the Triad One to its previous firmware image
and restore factory-default settings. The Status LED will blink white
rapidly when the factore restore begins.

Caution! The factory restore process will restore the Triad One to
a factory state and replace the firmware image with the factory­default firmware.

LED TROUBLESHOOTING GUIDE

Status LED = solid = flashing (4 Hz)

= flashing (2 Hz)

Booting Amplifier fault

Booting complete, has IP address Over-temperature condition

Connected to Director Amplifier is clipping occasionally

Playing audio (white LED)

No IP address USB over-current condition

Firmware is updating Factory restore in progress (white

Firmware update error Factory restore error

= flashing (1/2 Hz)

Amplifer is clipping constantly

LED)

REGULATORY/SAFETY INFORMATION

To review regulatory information for your particular Triad products, see the
information located on the Triad website at: http://triadspkrs.co/reg.

WARRANTY

Limited 2-year Warranty. Go to http://triadspkrs.co/warranty for details.

Copyright ©2017, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Sight,
Control My Home, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United
States and/or other countries. All other names and brands may be claimed as the property of their respective
owners. All specifications subject to change without notice.

SPECIFICATIONS

Zone line inputs 2 inputs, 1 analog stereo and 1 digital, (S/PDIF coax or TOSLINK optical)

Audio outputs 1 stereo analog out, 1 sub/mono audio out

Zone speaker outputs 1 stereo, Phoenix-style connector

USB 1 USB 2.0 port—supports playback of media stored on USB

IR 2 IR ports—3.5 mm jack

Ethernet RJ45 jack for local network connection, 10/100/1000BaseT

WiFi 2 internal antennas, 2.4 Ghz and 5 Ghz, 802.11b/g/n

Front power LED 1 × RGB status LED

ID button Yes

Factory restore button Ye s

Dimensions (H x W x D) 3 × 8.5 × 10.25" (7.6 × 21.6 × 26 cm)

POWER AMPLIFIER

Rated wattage/channel 100W @ 4 ohms

Minimum load impedance Tolerates 3 ohm loads minimum

Frequency response +/- 0.5 dB ref 1kHz 20-20,000 Hz 4 or 8 ohms

Noise < -105 dB reference to rated power “A” weighted

THD < 0.01% 1 kHz at all output levels below clipping

Typical < 0.005% at 1-50 watts RMS @ 1kHz in a 20 kHz bandwidth

Maximum voltage gain +25.6 dB

ANALOG AUDIO INPUT

Maximum input level 2V RMS

Analog to digital conversion 2V RMS = 0 dBFS

Analog frequency response +/- 0.1 dB, 20 - 20,000 kHz ref, 1 kHz

Analog dynamic range > 114 dB “A” Weighted

THD In a 20 kHz bandwidth < 0.001% 20 - 20,000 Hz up to 2V RMS

DIGITAL AUDIO INPUTS

S/PDIF input Accepts IEC 60958 standard inputs in 16/24-bit PCM stereo only,

Accepted sample rates 30 - 200 kHz for direct input mode; 44.1k, 48k, 96k, 192k for streaming output

Optical input TOSLINK Standard TOSLINK levels

GENERAL AUDIO

DSP audio processing 24-bit audio processing double-precision filters

Dynamic range > 105 dB

Tone controls +/- 12 dB with 650 Hz turnover frequency in 0.5 dB steps.

10-band EQ Ten one-octave filters centered at 31.5 Hz, 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz,

Volume control Attenuates from 0 to -80 dB and o in 0.5 dB Steps.

Loudness control Continuously variable from 100% volume to o. Follows approximate

Subwoofer output Mono summing of stereo audio or crossover mode

Subwoofer crossover type 4th order (24 dB/octave) Linkwitz-Riley

Supported crossover frequencies 80 Hz, 90 Hz, 100 Hz, 110 Hz, 125 Hz, 140 Hz

Signal present detectors -30 dB low pass filtered

THERMAL

Operating temperature 32° F ~ 102° F (0° C ~ 40° C)

Humidity 5% to 95% non-condensing

Storage -4 °F ~ 158 °F (-20 °C ~ 70 °C)

Cooling method Internal fan

Thermal dissipation 40 BTU/hr (standby), 680 BTU/hr (max)

surround not supported

mode

2 kHz, 4 kHz, 8 kHz, and 16 kHz, in 0.5 dB Steps +/- 12 dB

Fletcher-Munson curves.

www.control4.com | 1-888-400-4072 | DOC-00287-A 2017-08-28 DH