Winning Home WH100022 Quick Guide
DIN-Rail 8-Channel Relay Switch
Wiring Guide
Supported model
• C4-DIN-8RELSW-E DIN-Rail 8-Channel Relay Switch
Diagrams color code*:
Black Line
Red Load
Grey Neutral
Green Earth ground
Blue Ethernet
*Important! The wire colors shown in Figures 1 and 2 and in the
“Diagrams color code” table are examples only. Actual wire colors dier
by country and/or voltage.
Wiring diagrams
Use these Control4 DIN-Rail 8-Channel Relay Switch wiring diagrams along with
the DIN-Rail 8-Channel Relay Switch Installation Guide (
install DIN-Rail 8-Channel Relay Switches.
ctrl4.co/8chrelay-ig
) to
Figure 1. Wiring in Control4 panel
Distribution
Override switch
(breaker)
panel
Load 1
Load 2
Line 1
Load 3
Load 4
Line 2
Load 5
Load 6
Line 3
Load 7
Load 8
Line 4
Aux Override In
Aux Override Out
Neutral Out 1
Neutral Out 2
Neutral In 1
Neutral Out 3
Neutral Out 4
Neutral In 2
Neutral Out 5
Neutral Out 6
Neutral In 3
Neutral Out 7
Neutral Out 8
Neutral In 4
Ground
Important: Remove the four bypass
jumpers that connect each black
terminal to two red terminals by
unscrewing all three screws in each
bypass jumper until the entire bypass
jumper can be pulled out.
Load 1
Load 2
Neutral 1
Line 1
Load 3
Load 4
Neutral 2
Line 2
Load 5
Load 6
Neutral 3
Line 3
Load 7
Load 8
Neutral 4
Line 4
Aux in
Aux out
C4-DIN-8RELSW-E
8-Channel Relay Switch
Made in China/Fabriqué en Chine/中国制造
ATTENTION: Risque de choc électriqueNe pas ouvrir
undesired operation.
CAN ICES-3 (B)/NMB-3(B)
16A Max per Channel
1 HP Max per Channel @ 120V
2 HP Max per Channel @240V
Refer to documentation
for load ratings
Patent Pending
Prototype not for resale
To Ethernet switch
This device complies with part 15 of the FCC rules and ISED’s
license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
100-277V ,50/60 Hz
240V ,50 Hz
64A Max Total
16A Max per Circuit
Only Load 1 shown in detail
All modules sharing an auxiliary override
switch must be on the same electrical
voltage and phase.
Terminal block
Figure 2. Wiring in standard DIN rail panel
To Ethernet switch
Made in China/Fabriqué en Chine/中国制造
Load 1
Load 2
Neutral 1
Line 1
Load 3
Load 4
Prototype not for resale
Neutral 2
Line 2
ATTENTION: Risque de choc électriqueNe pas ouvrir
Load 5
Load 6
Neutral 3
This device complies with part 15 of the FCC rules and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
CAN ICES-3 (B)/NMB-3(B)
Load 7
Line 3
Load 8
Neutral 4
Line 4
100-277V ,50/60 Hz
240V ,50 Hz
64A Max Total
16A Max per Circuit
16A Max per Channel
1 HP Max per Channel @ 120V
2 HP Max per Channel @240V
Refer to documentation
for load ratings
Patent Pending
C4-DIN-8RELSW-E
8-Channel Relay Switch
Aux in
Aux out
Distribution
(breaker)
panel
control4.com | 888.400.4070
Copyright ©2019, Control4 Corporation. All rights reserved. Control4, the Control4
logo, the 4-ball logo, Control4 My Home, and Mockupancy are registered trademarks
or trademarks of Control4 Corporation or its subsidiaries in the United States and/or
other countries. All other names and brands may be claimed as the property of their
respective owners. All specifications subject to change without notice.
200-00595-A.3
A
2019-01-15 LW
Loading...