Winners Sun Plastic and Electronic WS 19004 User Manual

FCC ID:UR9WS-19004

Single Axis Pan-tilt Tripod

Quick Start Guide

Product description

5

6

7

8

9

1

2

3 4

1

Pan-tilt switch key

2

Balcony indicator

3

Rotate locking knob

4

Micro USB Charging interface

Rotary lock

5

6

Aluminum pull rod

7

Remote Controller Indicator

8

Photo key

9

Tripod

1

Bluetooth connection

Indicator lamp

Photograph key

If you use an Android phone, before taking photos,ensure

1

that the volume button of your phone is set to the shutter
button in camera settings.

Open Bluetooth of mobile phone to enter search state and

2

click “Dispho” in equipment searched; after connection is
nished,Green light long on。

2

Dispho

Usage method

1

Mount your phone onto the sele stick

2

Extend the monopod

3

3

Usage mode of pan-tilt holder

After clamping the mobile phone
and keeping the phone in natural
balance, then long press the power
button for 3 seconds to turn on the
mobile phone.

After starting up, it will enter the
stable mode, move the holder,
and the mobile phone will always
maintain a constant direction.

90°

Clicking the power button of the
pan-tilt holder, and it will rotate
90 degrees counterclockwise.

4

4

Non- pan-tilt mode

When the pan-tilt is shut down or out of power, the rotation
will screw tight to the locking direction, the rotation function
of the pan-tilt disappears, and it will become an ordinary
tripod sele stick. (When the rotation is reset to the holder
end, the pan-tilt mode will be restored.)

Yuntai Rotary Locking Key

5

Press the ll light button (optional)

Open the bottom tripod, uplift the pull rod and put tripod on
horizontal plane.

5

Charging

1

Holder charging mode

Connect the Micro USB interface of the pan-tilt holder for
charging, and the red light will be on for a long time during
the process of charging.；the redlamp will be off automatically
after charging is nished。

Micro USB interface

2

Battery replace of the remote control

Take the remote control out, turn the remote control to the
reverse side, and remove its back cover according to the
arrow direction,then the battery can be replaced.

Button
battery

6

Powering off

Remote controller: Long press photograph key for 3 s,green lamp
will icker for 3 times and then be off, which means machine is
shut down.
Pan-tilt holder: Long press the "on" button for 3 seconds, and the
green light will be off, indicating it is power off.

Tips

1.When the equipment clamps the platform bracket, try to keep
the equipment in the center, if not in the center, it is recommended
to use the vertical screen mode.

2.Sele stick will enter sleep mode automatically if it is idled for

10 min after Bluetooth connection; press photograph key to

recover connection.

3.The sele stick will be shut down automatically if it is idled for
30 min after entering sleep mode.

4.When using the Remote control , when the battery is low, the
Remote control will have a ashing red light for reminder. Please
replace the battery in time.

5.If the battery is running low, the indicator on the sele stick
will ash red. Charge the sele stick promptly

Winners' Sun Plastic & Electronics (Shenzhen)Co., Ltd.
Building E, Yingtai Industrial Zone, Longhua New District,
Shenzhen,China

Federal Communication Commission (FCC) Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirement, The device
can be used in portable exposure condition without restriction Federal
Communication Commission (FCC) Radiation Exposure Statement Power is so low
that no RF exposure calculation is needed.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, a

nd (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications or changes to this equipment. Such modifications or
changes could void the user’s authority to operate the equipment.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.