Congratulations! We welcome you to the exciting world of motor home travel and camping. You will
find it convenient and enjoyable to have all the comforts of home and still enjoy the great outdoors wherever you choose to go.
Your Ultimate Advantage motor home has been carefully designed, engineered and manufactured to
provide dependability as well as safety. Before sliding into the driver’s seat, take a few minutes to become
familiar with operations and features. This manual was prepared to aid you in the proper care and operation
of the vehicle and equipment. We urge you to read it completely. In addition, spend some time with the
dealer when you take delivery, you will want to learn all you can about your new motor home.
Your new Ultimate Advantage motor home is covered by a factory warranty against defects in material
and workmanship. This warranty should be validated at once and returned to the factory by your dealer.
About Safety Messages Used in This Manual
Throughout this manual, certain items are labeled Note, Caution, Warning or Danger. These terms alert
you to precautions that may involved damage to your vehicle or a risk to your personal safety. Read and
follow them carefully.
This SAFETY ALERT SYMBOL is used to draw your attention to issues which could involved
potential personal injury. This symbol is used throughout this manual and/or on labels affixed
on or near various equipment in this motor home.
DANGER
DANGER indicates a directly hazardous situation which, if not avoided,
will result in death or serious personal
injury.
.
WARNING
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or serious personal injury.
132000-11-003October 2002
CAUTION
CAUTION indicates a potentially
hazardous situation which, if not
avoided, could result in damage
mainly to equipment or property, but
in some cases may also result in
minor or moderate personal injury.
NOTE: A ‘Note’ is not necessarily safety related
but indicates a recommendation or special point
of information that could assist in understanding
the use or care of a feature item.
LP Gas Tank..................................................................................31 gal. (39 gal. w.c.)
Fresh Water Tank ................................................................................................99 gal.
Water Heater .......................................................................................................10 gal.
Black Water Holding Tank (Toilet).....................................................................50 gal.
Grey Water Holding Tank (Galley, Shower & Lavatory) ...................................54 gal.
*LP Gas tank capacity shown is the usable “full” LP gas capacity, which is 80% of the tank
manufacturer’s listed water capacity (w.c. shown in parenthesis). An LP tank must have at least 20% of
tank volume free to allow for expansion and proper vaporization of the liquid fuel. The tank is also
equipped with mandatory safety shut-off equipment that prevents filling above this level.
TABLE OF CONTENTS
INTRODUCTION
About this Manual ........................................ 0- 1
Systems ................................................... 10- 4
Removal from Storage ................................ 10- 6
INTRODUCTION
Congratulations on the purchase of your new
Ultimate Advantage motor home, which has been
carefully designed, engineered and quality built
by Winnebago Industries, Inc.
ABOUT THIS MANUAL
Please read this operator’s manual completely to understand how everything in your coach
works before taking it on its “maiden voyage.”
This manual is a guide to safe operation of the
features, equipment and controls in this coach.
Some equipment, such as the vehicle chassis and
certain electronic systems or appliances, have
their own comprehensive, manufacturer supplied
manuals or information sheets which describe
operation of these products in great detail. This
manual will refer you to the manufacturer’s information included in your Owner I
whenever necessary.
SUBJECT ICONS - To make it easy for you
to find information you’re looking for, we have
placed convenient, pictorial symbols called
“icons” beside many of the subject headings in
this manual. The icons correspond to the subject
matter of the section. These icons were designed
similar to the familiar international symbols
which identify public facilities such as restrooms
and handicap access. There are several examples
of icons on this page.
PAGE ICONS - The icons at the upper corners of each page correspond to the primary content of each main section of the manual, such as
LP Gas, Electrical, Plumbing, etc. This means
you can flip through the manual either forward or
backward and know exactly which main section
you are looking for just by watching the icons at
the top of the page. This means less paging back
and forth.
We also urge you to read the complete
Chassis Operating Guide provided by the
chassis maker and all other operating information provided by our equipment suppliers
and manufacturers. This is contained in your
Owner I
NFOCASE.
NFOCASE
This manual should be kept in the vehicle at
all times for personal reference. The operator’s
manual, I
are to be considered permanent components of
this vehicle. They should remain in the vehicle
when sold to provide the next owner with important safety, operating and maintenance information.
NOTE: The descriptions, illustrations, and spec-
NFOCASE and chassis operating guide
ifications in this manual were correct at
the time of printing. We reserve the right
to change specifications or design without notice, and without incurring obligation to install the same on products
previously manufactured.
SPARTAN CHASSIS OPERATING
GUIDE
Throughout this manual, frequent reference
is made to the vehicle chassis operating guide.
The chassis guide is the operator’s manual provided by Spartan, the manufacturer of the chassis
on which this motor home is built. Consult the
chassis guide for operating safety and maintenance instructions pertaining to the chassis section of the motor home.
CUMMINS DIESEL ENGINE
MANUAL
The diesel engine in your coach is built by the
respected Cummins engine company. Consult
the Cummins Operation and Maintenance
Manual for information on all engine related
topics such as engine maintenance, fluid level
checks, capacities, and service parts, etc.
0-1
INTRODUCTION
OWNER’S INFOCASE
Your InfoCase contains information supplied
by manufacturers of individual appliances and
equipment installed in your motor home.
Consult this information regarding the operation and care of appliances, accessories and special equipment.
OPTIONS AND EQUIPMENT
Some equipment described in this manual
may not apply to your coach.
BEFORE DRIVING
Before sitting in the driver’s seat, always
check around your vehicle to be sure you have
proper clearance for maneuvering. If necessary,
have a passenger help guide you out of a difficult
parking space.
Although your coach features automotive
conveniences like power steering and power
brakes, driving a motor home is different from
driving a car. A motor home is larger and heavier
than an automobile, so it requires more stopping
and passing distance, and more parking and maneuvering space than a car does.
signs. Know the height of your coach so you can
observe posted clearance limits. Also, remember
that some bridges, old ones in particular, may not
support the weight of your motor home. Know
the weight of your unit and observe any posted
weight limits.
Remember: Always use your seat belt and be
sure your passengers do so as well. We also advise making frequent rest stops while traveling to
relieve stress on yourself, your passengers and
your vehicle.
SERVICE AND
ASSISTANCE
Your Ultimate Advantage dealer will be glad
to provide any additional information you need,
as well as answer any questions you might have
about operating the equipment in your motor
home. When it comes to service, remember that
your dealer knows your vehicle best and is interested in your satisfaction. Your dealer will provide quality maintenance and any other
assistance that you may require during your ownership of this vehicle.
If you need warranty repairs while traveling,
however, you may take your motor home to any
Winnebago or Itasca dealership and they will assist you.
Always be aware of the size of your motor
home. The added height of rooftop accessories or
luggage boxes may cause clearance problems
around some tunnels, canopies and hanging
0-2
WARRANTY
Your new Ultimate Advantage is covered by
a factory warranty against defects in material and
workmanship. This warranty should be validated
immediately and returned to the factory by your
dealer. For additional information, see your
“New Vehicle Limited Warranty” included with
this vehicle.
DRINKING AND DRIVING
Winnebago Industries supports the recommendations of the Presidential Commission on
Drunk Driving.
·Exercise your good judgment and encourage
others to do the same.
·Know the legal limits and do not exceed
them.
·Also know your personal limits, which may
be lower than the legal limits.
·Should you ever exceed your limits, find
alternative transportation; call a cab, ask a
friend to drive you home or call a family
member to come and get you.
The presence of alcohol in significant levels
in the blood increases the probability that the
driver will be involved in an accident.
INTRODUCTION
REPORTING SAFETY DEFECTS
If you believe that your vehicle has a defect
which could cause a crash or could cause injury
or death, you should immediately inform the
National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Winnebago
Industries, Inc.
If NHTSA receives similar complaints, it
may open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it may
order a recall and remedy campaign. However,
NHTSA cannot become involved in individual
problems between you, your dealer, or Winnebago Industries.
To contact NHTSA, you may either call the
Auto Safety Hotline toll-free at 1-800-424-9393
(or 366-0123 in Washington, D.C. area) or write
to: NHTSA, U.S. Department of Transportation,
Washington, D.C. 20590. You can also obtain
other information about motor vehicle safety
from the Hotline.
0-3
INTRODUCTION
VEHICLE CERTIFICATION LABEL
This label contains vehicle identification and
other important reference information. The vehicle certification label is located on the sidewall to
the left of the steering wheel. Never remove or
destroy this label.
THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY
STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.
SERIAL NO. _________________________ VIN______________________________
TYPE ____________________ MODEL ____________________ COLOR__________
5
10
12
SUITABLE TIRE AND RIM CHOICE COLD INFLATION
EXPLANATION OF DATA
1. Chassis manufacturer.
2. Chassis manufacture date.
3. Month and year of manufacture at Win-
nebago Industries.
4. Gross Vehicle Weight Rating: Total permis-
sible weight of the vehicle, including driver,
passengers, total cargo carried (including all
liquids) and equipped with all options.
5. Gross Axle Weight Rating: Total permissible
weight allowed for the front and rear axles
(listed in pounds and kilograms).
6. Suitable Tire Choice: Tires recommended to
meet handling and safety requirements.
When replacing any of the tires on your
vehicle, always replace with a tire that meets
these specifications.
7. Suitable Rim Choice: Wheel rims recom-
mended to meet handling and safety require-
ments. When replacing any of the rims on
INCOMPLETE VEHICLE MANUFACTURED
BY MOTOR CORP.
MONTH AND YEAR OF MANUFACTURE:________
GVWR_______LB _________KG
TIRE RIM PRESSURE
6
1
4
7
11
13
8
14
9. Rear Axle Wheel Configuration: Single or
Dual.
10. Serial Number: This is the serial number
assigned to the completed vehicle by Winnebago Industries.
11. Vehicle Identification Number (VIN): This
number identifies the chassis on which the
motor home is built. The 10th digit of the
VIN designates the chassis model year.
(2=2002, 3=2003) This information is useful
when ordering chassis repair parts.
12. Type: States the NHTSA designated usage
classification for your motor home. MPV
signifies a Multi-purpose Passenger Vehicle.
13. Model: Lists the Winnebago product model
number of your vehicle.
14. Color: Signifies the color code number of the
decor used throughout the vehicle. This
number is necessary for ordering replacement cushions, curtains, carpet, etc.
2
your vehicle, always replace with a rim that
meets these specifications.
8. Cold Inflation Pressure: Inflation pressures
recommended (while Cold) for the tires originally equipped on your vehicle. These pressure levels must be maintained to assure
proper handling, safety and fuel economy.
9
0-4
INTRODUCTION
EXTERIOR FEATURE IDENTIFICATION
Composite model shown for illustration purposes only.
Actual locations of features depends on coach model and options.
**Also contains optional freezer unit if equipped.
††Also contains Cable TV and Phone hookups and engine block heater plug-in.
!Be Careful! Exhaust outlet surface may become HOT while using furnace or water heater.
0-5
SECTION 1
SAFETY PRECAUTIONS
Read and understand all instructions and precautions in this manual before operating your
new motor home. Throughout this manual, certain items are labeled NOTE, CAUTION and
WARNING. These terms alert you to precautions
that can involve risk to your vehicle or to your
personal safety. Read and follow them carefully.
NOTE: Indicate special points of information.
CAUTION
Indicates that a failure to observe can
cause damage to vehicle or equipment
WARNING
This symbol is used to alert you to
precautions that involve your personal safety as well as vehicle damage. Read and follow them carefully.
Listed below are some safety precautions that
must be adhered to. These precautions as well as
others that involve damage to equipment are also
listed in the appropriate areas in this manual.
·Make sure all passengers have seat belts fastened in a low and snug position so the force
exerted by the belt in a collision will be
spread across the strong hip area. Pregnant
women should wear a lap-shoulder belt
whenever possible, with the lap belt portion
worn low and snug throughout the pregnancy.
·Before driving, secure dinette chairs with retainer strap provided as shown in Section 8.
·Never let passengers stand or kneel on seats
while the vehicle is moving.
·Sleeping facilities are not to be utilized while
vehicle is moving.
·Examine the escape window and be familiar
with its operation, but do not use except in an
emergency.
•Inspect the fire extinguisher monthly for
proper charge and operating condition. This
should also be done before beginning a vacation or any extended trip.
DRIVING
GENERAL WARNINGS
·Only seats equipped with seat belts are to be
occupied while the vehicle is moving.
·All seats which can be positioned, such as
swiveling, sliding, reclining, or footrest out,
must be placed in a fully upright and swivellocked position with footrests retracted while
the vehicle is moving. Some swivel lounge
chairs are designed to lock in a forward
facing position, while others lock in an aisle
facing position. Be certain these seats are
secure from swiveling before traveling.
·Do not attempt to adjust the driver’s seat
while the vehicle is moving.
·Do not adjust tilt steering in a moving vehicle.
·Do not operate the cruise control on icy or
extremely wet roads, winding roads, in heavy
traffic, or in any other traffic situation where
a constant speed cannot be maintained.
·Use care when accelerating or decelerating
on a slippery surface. Abrupt speed changes
can cause skidding and loss of control.
1-1
SECTION 1
IT IS NOT SAFE TO USE COOKING
APPLIANCES FOR COMFORT HEATING
COOKING APPLIANCES NEED FRESH AIR FOR SAFE OPERATION.
BEFORE OPERATION:
1. OPEN OVERHEAD VENT OR TURN ON EXHAUST FAN AND;
2. OPEN WINDOW.
SAFETY PRECAUTIONS
·Driving through water deep enough to wet
the brakes may affect stopping distance or
cause the vehicle to pull to one side. Check
brake operation in a safe area to be sure they
have not been affected. Never operate any
vehicle if a difference in braking efficiency is
noticeable.
·Adverse weather conditions and extremes in
terrain may affect handling and/or performance of your vehicle. Refer to your chassis
manual for related information.
FUEL & LP GAS
·All pilot lights must be extinguished and appliances turned off while refilling the fuel
tank or LP tank.
·Never smoke while refilling vehicle fuel tank
or LP gas tank.
·Avoid inhaling exhaust gases produced by
burned gasoline, diesel fuel or LP gas in
items such as the range, chassis engine, generator engine, refrigerator, furnace and water
heater. They contain carbon monoxide,
which is an odorless, colorless and poisonous
gas.
·Do not bring or store LP gas containers, gasoline or other flammable liquids inside the
vehicle because a fire or explosion may result. LP gas containers are equipped with
safety valves which relieve excessive pressure by discharging gas to the atmosphere.
·Do not alter the LP gas system at any time or
in any way.
·Do not fill LP gas container(s) above 80 percent of capacity. Overfilling the LP gas container can result in uncontrolled gas flow
which can cause fire or explosion. A properly
filled container will contain approximately
80 percent of its volume as liquid LP gas.
1-2
·Never use an open flame to test for LP gas
leaks. Replace all protective covers and caps
on LP system after filling. Make sure valve is
closed and door latched securely.
·Never connect natural gas to the LP gas system.
·When lighting range burners do not turn
burner controls to “On” and allow gas to escape before lighting match.
·Portable fuel-burning equipment, including
wood and charcoal grills and stoves, shall not
be used inside the recreational vehicle. The
use of this equipment inside the recreational
vehicle may cause fires or asphyxiation.
·LP gas regulators must always be installed
with the diaphragm vent facing downward.
Regulators are equipped with a protective
cover. Make sure that the regulator vent faces
downward and that the cover is kept in place
to minimize vent blockage which could result
in excessive gas pressure causing fire or explosion.
·The following warning label is located in the
cooking area to remind you to provide an adequate supply of fresh air for combustion.
WARNING
IT IS NOT SAFE TO USE COOKING
APPLIANCES FOR COMFORT HEATING
COOKING APPLIANCES NEED FRESH AIR FOR SAFE OPERATION.
BEFORE OPERATION:
1. OPEN OVERHEAD VENT OR TURN ON EXHAUST FAN AND;
2. OPEN WINDOW.
Unlike large homes, the oxygen supply inside
a recreational vehicle is limited due to its
size. To avoid danger of axphyxiation, provide proper ventilation when using the gas
rangetop or gas oven. It is especially important that the gas oven and range top not be
used for comfort heating. Danger of asphyxiation is greater when these appliances are
used for long periods of time.
LP GAS LEAKS
P
The following label is located in the vehicle
near the range area. If you smell gas within the
vehicle, quickly and carefully perform the procedures listed.
IF YOU SMELL GAS
1. Extinguish any open flames, pilot
lights and all smoking materials.
2. Do not touch electrical switches.
3. Shut off the gas supply at the tank
valve(s) or gas supply connection.
4. Open doors and other ventilating
openings.
5. Leave the area until odor clears.
6. Have the gas system checked and
leakage source corrected before
using again.
LP GAS ALARM
Your coach is equipped with an LP gas detector which sounds an alarm if an unsafe amount of
LP gas is present inside the coach. Because LP
gas is heavier than air, the detector is located on
a cabinet face near the floor of the coach.
SECTION 1
SAFETY PRECAUTIONS
ress to stop alarm
Green
(Active)
If The Alarm Sounds
If the alarm sounds, do not touch any electrical switches. Immediately turn off the main LP
tank valve and all LP appliances, open all windows and roof vents, and leave the coach until
the alarm stops sounding.
If the alarm keeps sounding at regular intervals, a leak may be present. Contact your dealer
or an LP gas service center to have the problem
corrected before using the LP system again.
If the coach batteries become extremely
drained, an amber light on the face of the alarm
will come on and in some cases the LP alarm may
begin to sound on its own. This condition typically occurs only during storage situations when
battery charge is not being restored by the inverter charger or solar charger.
Red
(Alarm)
Amber
(Low Batt.)
WARNING
Never use an open flame to test for
gas leaks. When testing for gas line
leaks with a soapy water solution, DO
NOT use a detergent containing
ammonia or chlorine. These substances may generate a chemical
reaction causing corrosion to gas
lines, resulting in dangerous leak conditions.
Power Connection
A green light on the face of the alarm shows
when the unit is active. The red button is used to
reset the alarm.
The gas alarm is powered by the coach batteries. If the battery cable is disconnected from the
batteries, auxiliary battery switch is shut off, or
the circuit breaker is tripped, the alarm will not
1-3
SECTION 1
SAFETY PRECAUTIONS
work. The LP gas alarm breaker is located on the
coach breaker fuse panel shown in Section 6.
Because the LP gas alarm is connected directly to the auxiliary battery, it is always drawing a
small amount of current. Even though this current
draw is slight, it could drain the coach battery
during storage periods of 30 days or longer. We
recommend turning the auxiliary battery switch
off or disconnecting the battery cables from the
auxiliary battery during extended storage periods
to avoid discharge.
Further Information
See the manufacturer’s information entitled
“Your LP Gas Detector” in the Owners InfoCase
for further instructions on nuisance alarms and
care and testing of the LP gas detector.
LOADING
·Store or secure all loose items inside the
motor home before traveling. Possible overlooked items such as canned goods or small
appliances on the countertop, cooking pans
on the range, or free-standing furniture items
can become dangerous projectiles during a
sudden stop.
·Be aware of GVWR, GAWR and individual
load limit on each tire or set of duals. (See
“Loading the Vehicle” in Section 4.)
·Never load the motor home in excess of the
gross vehicle weight rating or the gross axle
weight rating for either axle.
ELECTRICAL
·Careless handling of electrical components
can be fatal. Never touch or use electrical
components or appliances while feet are bare,
while hands are wet, or while standing in
water or on wet ground.
·Improper grounding of the vehicle can cause
personal injury. Do not plug the utility power
cord into an outlet which is not grounded and
do not adapt the plug to connect to a receptacle for which it is not designed.
·Do not attach an extension cord to the utility
power cord.
·Be sure that all electrical appliances to be
used contain 3-prong plugs for proper
grounding.
·Avoid overloading electrical circuits. Replace fuses or circuit breakers with those of
the same size and amperage rating only.
Never use a higher rated fuse or breaker.
·Use caution when handling or working near
electrical storage batteries. Always remove
jewelry and wear protective clothing and eye
covering. Avoid creating sparks.
NOTE: Your motor home’s load capacity is
designated by weight, not by volume, so
you cannot necessarily use all available
space when loading your motor home.
MAINTENANCE
·Do not remove the radiator cap while engine
and radiator are still hot. Always check coolant level visually at the see-through coolant
reservoir.
·Never get beneath a vehicle that is held up by
a jack.
·Do not mix different construction types of
tires on the vehicle such as radial, bias or belted tires, as vehicle handling may be affected.
Replace tires with exact size, type and load
range.
·Do not attempt to start the vehicle by hot wiring.
1-4
SECTION 1
SAFETY PRECAUTIONS
FORMALDEHYDE INFORMATION
WARNING
Some components in this vehicle contain formaldehyde based adhesives
which may release formaldehyde
fumes into the air for an unknown
period of time until total dissipation
occurs. Individuals who are allergic
to formaldehyde gas fumes may
experience irritation to eyes, ears,
nose and throat. Reaction in infants
may be more severe. Although long
range effects are not well understood,
testing to date has not revealed any
serious health effects in humans at the
level of emission from these
products.
IMPORTANT
To aid in dissipation, ventilate the vehicle by
opening all windows and circulating the air with
a fan.
CARBON MONOXIDE
WARNING
·Each time the vehicle is raised for an oil
change.
·Whenever a change in the sound of the exhaust system is noticed.
·Whenever the exhaust system, underbody or
rear of the vehicle is damaged.
To allow proper operation of the vehicle’s
ventilation system, keep front ventilation inlet
grill clear of snow, leaves or other obstructions at
all times. DO NOT OCCUPY A PARKED VEHICLE WITH ENGINE RUNNING FOR AN
EXTENDED PERIOD.
Do not run engine in confined areas, such as a
garage, except to move vehicle in or out of area.
When vehicle is stopped in an UNCONFINED
area with the engine running for any more than a
short period, adjust heating or cooling system to
force outside air into the vehicle as follows:
1. Set fan to medium or high speed and vent
control to air.
2. On vehicles equipped with air conditioning,
set fan to medium or high speed and set control to obtain maximum vent air.
Rear windows should be closed while driving
to avoid drawing dangerous exhaust gases into
the vehicle.
WARNING
Avoid inhaling exhaust gases, as they
contain carbon monoxide, which is a
colorless, odorless and poisonous gas.
If your suspect that exhaust fumes are entering
the passenger compartment, have the cause determined and corrected as soon as possible. If you
must drive under these conditions, drive only
with ALL WINDOWS FULLY OPENED.
The best protection against carbon monoxide
entry into the vehicle body is a properly maintained engine exhaust and ventilation system. It is
recommended that the exhaust system and body
be inspected by a qualified motor home service
center.
CARBON MONOXIDE
ALARM
Your coach is equipped with a carbon monoxide (CO) alarm, located on the ceiling in the bedroom area.
Red Light
(Press to Test Alarm)
Yellow Light
(Warning)
1-5
SECTION 1
SAFETY PRECAUTIONS
The CO alarm is powered by a 9-volt battery
and contains a sensor that is designed to detect
toxic carbon monoxide gas fumes resulting from
incomplete combustion of fuel. It will detect CO
gas from any combustion source such as the furnace, gas range/oven, water heater, refrigerator,
chassis engine, and electric generator engine.
·Patented biomimetic sensor mimics the
human response to Carbon Monoxide.
·Test/Reset provides for one time alarm
silence and multiple warning silence. Also
tests alarm circuitry, microprocessor, battery
and horn.
·Red light flashes once every thirty seconds in
normal operation.
·Continuous yellow light with a beep every
three seconds indicates an unhealthy CO
level.
·Continuous red light and pulsating alarm sig-
nal a dangerous CO condition.
·Battery operation provides protection 100%
of the time. Low battery signal alerts consumer of need to replace battery.
·85 decibel alarm assures waking during
sleeping hours.
EMERGENCY EXITS
Emergency Exit Windows
Your motor home is equipped with an emergency exit window on the left (driver’s) side of
the bedroom which functions as an escape exit in
an emergency situation.
WARNING
Use emergency window for emergency exit only. Do not test for proper
operation.
Use care when exiting emergency
window, as broken glass may be
present in the exit area.
The side mounted escape window is secured
by two safety latches and can be opened by first
releasing these two latches and then pushing outward on the lower part of the window. Identify
which type of emergency exit window is in your
vehicle.
Monthly Testing
Press the TEST button on the face of the alarm
periodically (at least monthly) to check the function of the alarm and condition of the battery. If
the alarm begins to beep every few seconds, the
battery may be weak and need replacement.
(Press the TEST button to be sure before replacing the battery. If the alarm sounds, the battery
may still be okay. If the alarm still beeps every
few seconds, check the smoke detector also. The
“low battery” warning beep is similar on many
alarm devices, so the origin of this electronic
sound can be deceiving.)
Further Information
Please read the information provided by the
manufacturer, which is included in your Owner’s
InfoCase. It includes information on precautions,
operational testing, and battery/sensor replacement.
Lift Both Handles Up
Push Out on Bottom of Window
Instructions for removal are also located on a
label on the glass for quick reference and for passengers who may not be familiar with the exit.
Never remove or destroy this label.
Using Slider Windows as Emergency Exits
Slider windows along the side of the motor
home can also be used as emergency exits,
1-6
should the need arise. To use the windows as
exits, slide the window open, then slide the
screen open.
SAFETY DEVICES
FIRE EXTINGUISHER
A dry chemical fire extinguisher is located
near the floor behind the passenger seat.
SECTION 1
SAFETY PRECAUTIONS
SMOKE ALARM
Your motor home is equipped with a smoke
alarm located on the ceiling in the galley and
lounge area. This alarm meets U.L. Standard 217
and NFPA Standard 74 for operation of smoke
detection devices.
We recommend that you become thoroughly
familiar with the operating instructions displayed
on the side of the fire extinguisher or in the information supplied in your Owner’s InfoCase.
We also recommend that you inspect the fire
extinguisher for proper charge at least once a
month in accordance with National Fire Protection Association (NFPA) recommendations as
stated on the label. If the charge is insufficient,
the fire extinguisher must be replaced.
WARNING
Do not test the fire extinguisher by
discharging it. Partial discharge can
cause leakage of pressure or contents
which would render the unit inoperative when needed. When using the
fire extinguisher, aim the spray at the
base of the fire.
1. The smoke alarm should be tested for correct
operation each time the vehicle is brought
out of storage, before each trip, and at least
once a week during motor home use. To test
the electronics, firmly depress the button. To
test that smoke reaches the sensor, blow
smoke in a careful, fire-safe manner into
your smoke alarm.
Press to Test
2. Your smoke alarm will not work without
power. Never remove the battery to quiet the
alarm. When your smoke alarm “beeps”
about once a minute the battery is weak.
1-7
SECTION 1
SAFETY PRECAUTIONS
Install a new battery immediately. Be sure to
use only batteries specified in manual or on
unit. Test unit after installing a new battery.
3. Clean and vacuum the openings on your
smoke alarm once a month.Do not open the
smoke alarm or try to repair it. For replacement information see warranty in Owner’s
Manual.
4. Smoke alarms have technical limitations and
may not respond in all situations. FIRE PREVENTION is your best safeguard.
See your Owner’s InfoCase for further infor-
mation.
1-8
DRIVING YOUR MOTORHOME
(See also Safety Precautions, Section 1 of this
manual.)
NOTE: See your Spartan chassis operator's
manual for information on starting the
engine, operating the transmission,
steering column controls descriptions of
instrument gauges and other chassis related information.
Some items described in this section may
be optional or unavailable on your
coach.
BEFORE ENTERING YOUR
VEHICLE
Before entering your vehicle, there are a few
recommended procedures that will aid in your
driving safety and equipment.
SECTION 2
WARNING
The engine should be shut off unless
specifically required for a certain procedure.
The transmission must be in N (Neutral) and park brake applied while
performing any checks or adjustments.
7. Unhook and store sewer and water supply
hoses.
8. Retract step.
9. Be sure that all of your cargo is secured in
event of a sudden stop or an accident.
10. Check around your vehicle in all directions
to assure that you have proper clearance.
11. Lower TV antenna and satellite dish.
12. Disconnect and store shoreline.
1. Be sure that the windows, mirrors and light
lenses are clean and unobstructed.
2. Make sure all exterior lights operate properly.
3. Check tires for proper cold inflation pressures and inspect for any unusual wear.
4. Check wheel lug nuts for tightness.
5. Look beneath the vehicle for noticeable fluid
leakage.
6. Check fluid levels and fill if necessary. This
includes engine oil, transmission fluid, coolant, brake fluid, power steering fluid and
windshield washer solvent.
WARNING
Before driving your vehicle, be sure
you have read the entire operator’s
manual and that you understand your
vehicle’s equipment completely and
how to use the equipment safely.
BEFORE DRIVING YOUR
VEHICLE
Before preparing to drive your vehicle, here
are a few recommended procedures that will add
to your driving safety and enjoyment.
1. Be sure that you adjust the interior and exte-
rior rear view mirrors to your driving preference.
2. Adjust the driver's seat for proper distance
from foot pedals and steering wheel to allow
2-1
SECTION 2
DRIVING YOUR MOTOR HOME
for safety and ease in controlling your vehicle.
3. Place front seats in the forward facing position.
4. Be sure to fasten all safety belts to fit you
comfortably, but tight enough to obtain the
full safety of the belts.
5. Make sure all doors are completely shut and
locked. When the doors are shut and locked,
there is less chance of the doors flying open
in event of an accident. It also prevents unintentional opening of doors and keeps intruders out of your vehicle.
6. Check to see that all gauges are operating
properly.
7. Check the fuel level in the vehicle.
8. Be certain that the fire extinguisher is fully
charged and secure in its mounting bracket.
CAUTION
Be sure hood and all compartment
doors are latched securely before
driving vehicle.
“KEY ONE” LOCK SYSTEM
Your coach is equipped with the new Key
TM
One
door lock in the entire motor home (except the security deadbolt lock on the entrance door). This
means you don’t have to sort through a handful of
keys to find the right one for the water fill door or
the luggage doors or the entrance door or the
driver’s door.
our factory database, so if you ever lose your
keys, any Winnebago Industries dealership can
easily order a new key for you. They are also
equipped with special master keys and can unlock your coach for you if needed.
lock system. A single key will open every
The key number for your coach is registered in
FUEL SELECTION
Refer to your Spartan chassis operating guide
for the manufacturer's recommendations on proper fuel selection.
Winter Fuel Waxing and Anti-Gel Additives
In sub-freezing temperatures, #2 diesel fuel
can form small wax crystals that become trapped
in the fuel filter and block the fuel flow to the
engine, causing it to stall out. At sub-zero temperatures, the fuel can congeal and turn
“slushy”. If this happens, the only remedy is to
have the vehicle towed into a heated facility to
allow the fuel to warm up and become fully
liquid again.
During winter time, most truck stops and
reputable filling stations have winter blend
diesel fuels available that are less susceptible to
waxing.
There are also commercially available products, typically called anti-gel additives, to add to
diesel fuel while filling the tank to inhibit wax
formation in freezing temperatures.
Consult your Spartan chassis guide or Cummins engine guide for more information on fuel
requirements and additives.
FILLING THE FUEL TANK
Diesel fuel, especially #2 grade, can foam up
while being pumped into the tank. Sometimes
this foam can cause the pump nozzle to shut off
before the tank is actually full. Allow the foam to
settle then resume filling at a slower flow rate
until the tank is full.
Diesel Fuel Tank Capacity .........100 gal. diesel
(single tank w/dual fills)
2-2
STARTING AND
STOPPING ENGINE
Refer to your Spartan chassis operating guide
for the manufacturer's recommendations on starting and stopping the engine.
See also “Engine Block Heater” elsewhere in
this section.
SECTION 2
DRIVING YOUR MOTOR HOME
Idling Diesel Engine
CAUTION
The Cummins diesel engine must be
set to 1000 rpm fast idle mode if
idling for more than 10 minutes or the
engine will be severely damaged.
To Increase Idle Speed: While idling, press the
Cruise Control ON button, then press the SET
button momentarily. This will automatically set
the engine idle speed to 1000 rpm. The engine
idle speed can be increased (or ‘ramped up’) by
holding the SET button and releasing at the
desired rpm speed - anywhere from 1000 rpm to
a maximum of 1700 rpm.
To Decrease Idle Speed: Press the Cruise Control RES button momentarily to ‘bump down’
rpm’s in preset increments, or press and hold to
‘ramp down’ to 1000 rpm..
To Cancel High Idle: Press the Brake pedal to
return to normal engine idle speed - especially
before shifting the transmission when you are
ready to drive off. You can also do this by pressing the cruise control On/Off or Cancel buttons.
Cold Weather Starting: Please note the following cold weather starting precautions. These
labels are also located in appropriate areas of the
coach. Failure to follow these precautions could
cause serious damage to your diesel engine.
ENGINE BLOCK HEATER
Your coach is equipped with an engine block
heater to assist starting in freezing temperatures.
The power cord is located in the rear cargo compartment on the driver side of the coach. When
plugged into the receptacle, the heater is connected to both the shoreline and the auxiliary generator, so a separate extension cord is not needed.
The power switch is a standard household light
switch located above the OnePlace panel.
Diesel Engine Heater Switch
To Use the Engine Heater
With the shoreline cord plugged into a shoreline hookup, turn on the engine heater power
switch on the forward bedroom wall on the driver’s side of the coach.
If a shoreline hookup is not available, just start
the auxiliary generator to provide power to the
engine heater.
REMEMBER! Turn the engine heater switch off
after starting the engine. The heater will keep
operating for as long as it is supplied with electricity. If the switch is left on, the engine heater
will come on each time you hook up the shoreline
cord or start the generator.
2-3
SECTION 2
DRIVING YOUR MOTOR HOME
PARKING BRAKES
The parking brakes are applied by pulling outward on the large yellow knob on the dash to the
left of the steering column. Push the knob in to
release the brakes.
Exhaust Brake Switch
Parking Brake Knob
Use the parking brakes whenever the vehicle
is parked. Never try to drive the vehicle with the
park brake applied. This can cause excessive
wear on the brakes and may damage the transmission.
NOTE: It is normal to hear an occasional burst
of air pressure from the rear of the vehicle. This is an automatic moisture purging feature of the air brake system. See
the Brakes section of your Spartan chassis manual for instructions on periodic
draining of brake air tank.
JACOBS® EXTARDER™ ENGINE
EXHAUST BRAKING SYSTEM
To Use the Exhaust Brake: The exhaust brake
activation switch is located on the lower left side
of the dash. Press and release the ON side of the
switch to activate the exhaust brake system. The
exhaust brake will operate whenever you let up
on the throttle pedal while the switch is ON.
Press and release the OFF side of the switch to
deactivate the exhaust brake system and return to
chassis brakes alone.
How It Works: The Jacobs
device that generates “braking” power by controlled restriction of the engine’s exhaust gas
flow.
When the exhaust brake is activated, a valve
closes off the engine’s exhaust causing the exhaust back pressure to increase, which causes the
vehicle to slow down.
The increased back pressure would normally
stop the engine except the forward momentum of
the vehicle keeps the drivetrain and the engine
turning.
This controlled back pressure helps to regulate
a vehicle’s downhill speed, such as on mountainous or hilly roads. It also provides “braking” on
level or near-level roads.
®
ExtarderTM is a
WARNING
Do not activate the engine exhaust
braking system while on icy or
extremely wet roads or in any other
situation where abrupt deceleration
could cause skidding or loss of vehicle control.
HAZARD WARNING
LIGHTS
The hazard warning flasher switch is located
on the underside of the steering column near the
2-4
SECTION 2
DRIVING YOUR MOTOR HOME
signal/cruise lever. Pull the switch button outward from the column to activate the flashers. To
cancel flashers, push the switch button inward toward the column. See also Section 3 for further
operating information.
Hazard Light Switch
Pull On/Push Off
HEADLIGHT BEAM CHANGE
AND TURN SIGNALS
Move multi-function lever upward for right
turn signal and downward for left turn signal.
Pull end of handle toward you to switch high
beam to low, or low beam to high.
STEERING COLUMN TILT/TELESCOPE
The tilt/telescoping adjustment lever is locat-
ed on the left side of the steering column.
To Adjust Tilt Wheel: Pull the lever toward you
and tilt the steering wheel to the desired angle,
then release the lever.
SIGNAL LEVER/
HEADLIGHT HI/LO BEAM
The signal lever controls the turn signals,
high/low beam changing.
Turn Signals/Hi-Lo Beams
Pull to Tilt
Push to Telescope
To Adjust Telescoping Column: Push the lever
toward the dash. Push or pull the steering wheel
to slide the steering column in or out to the
desired length. Release the lever to lock the column into position.
WARNING
Do not adjust the steering column or
tilt wheel while the vehicle is in
motion. This could cause a loss of
vehicle control.
2-5
SECTION 2
DRIVING YOUR MOTOR HOME
SMARTWHEELTM STEERING WHEEL
CONTROL SYSTEM
TM
The Smart Wheel
Control System offers
convenient and safe control of the horn, headlight
and marker light flash, cruise control, and wiper
functions all from switch panels mounted at your
fingertips on the steering wheel.
HORN BAR
•Normally sound chassis horn.
•Also sounds air horns if Air Horn switch on
dash is activated.
HEADLIGHT COURTESY FLASH
•Press and release to blink or flash the head-
lights.
•Night: If the headlights are already turned
on, pressing the switch will blink them off
briefly.
•Day: If the headlights are off, pressing the
switch will flash them on briefly.
(Truckers often use this signal to indicate to a
passing rig when it is clear to pull back into the
lane ahead of them.)
(Truckers often use this signal as a greeting or
an expression of thanks for assistance in passing,
etc.)
CRUISE CONTROL FUNCTIONS:
ON/OFF (Cruise System On/Off)
•Press to turn cruise control system on or off.
•This will also erase previously set speed.
SET (Set Speed/Coast)
•Press to maintain current desired driving
speed. Will not work below 40 mph.
•This button will also perform “Coast” fea-
ture. Press and hold until vehicle slows to
desired speed and release to establish new
‘set’ speed.
Cruise Control
Pad
Horn Bar
Wiper Control
Pad
MARKER LIGHT COURTESY FLASH
•Press and release to blink or flash the marker
(clearance) lights.
•Night: If the marker lights are already turned
on, pressing the switch will blink them off
briefly.
•Day: If the marker lights are off, pressing the
switch will flash them on briefly.
RES (Resume/Accel)
•Press to return to previous ‘set’ speed after
braking or reducing speed.
CANCEL
•Press to switch cruise function off without
losing current ‘set’ speed.
2-6
WARNING
Do not operate the cruise control on
icy or extremely wet roads, winding
roads, in heavy traffic, or in any other
traffic situation where a constant
speed cannot be maintained.
WIPER FUNCTIONS:
There are four wiper control buttons:
•ON/HI/LO
•DELAY
•WASH/WIPE
•OFF
WA S H/ W IP E
•Press switch to activate Lo wipers and spray
washer fluid onto the windshield for as long
as you hold the button.
•After you release the button, the wipers will
continue for three wipe cycles, then turn off.
•If wipers are already active, pressing the
switch will simply spray fluid onto the windshield without affecting wiper setting.
SECTION 2
DRIVING YOUR MOTOR HOME
Here’s how it works:
•During a light rain or mist, when your windshield needs a clearing wipe, press the button
once and the wiper will swipe back and forth
once a Lo speed. Let’s say 7 seconds later,
the windshield needs another wipe - press
the button again and the delay time will be
set to 7 seconds.
•If the mist gets heavier and you press the
button again 3 seconds after the last wipe,
the delay time will be reset to 3 seconds.
•The delay time can be set from approximately 1 to 30 seconds.
WIPER OFF
•Press to shut wipers off.
•Wipers will also switch off whent he ignition
is turned off.
NOTE: Many states now have laws that require
headlights to be on during precipitation
conditions. To assure compliance with
this law, the headlights will come on
whenever you press any of the wiper
function buttons - Hi/Lo, Wash or Delay.
You can manually reset the headlights by
the cycling the headlight switch (on the
dash) on and off. The headlights will also
turn off when the ignition switch is
turned off.
WIPER ON/HI/LO
•Press to turn wipers on at Lo speed
•then press again to switch wiper speed back
and forth from Lo to Hi speed.
•Press Off button to switch wipers off.
WIPER DELAY
This switch will set a Lo speed wiper delay time
based on the duration between any two presses
of the button.
IDLE SPEED CONTROL
The cruise control system can also be used to
increase or decrease engine idle speed (rpm)
while parked if desired. Press the ON/OFF button
to activate or deactivate the idle control circuit.
Press the Brake Pedal to cancel idle speed functions and return to normal idle.
SET BUTTON INCREASES IDLE RPM
FROM NORMAL IDLE SPEED:
•Press and release to increase engine speed
from normal idle to about 1000 rpm.
•Press and hold to ‘run up’ engine speed, then
release at desired rpm. Maximum idle speed
is about 1700 rpm.
•Press the On/Off or Cancel buttons or the
Brake Pedal to return the engine to normal
idle.
2-7
SECTION 2
DRIVING YOUR MOTOR HOME
RES BUTTON DECREASES HIGH IDLE
RPM:
•Press momentarily to ‘bump down’ engine
rpm in preset increments until it settles back
to 1000 rpm.
•Press and hold to ‘ramp down’ engine speed
until it settles back to 1000 rpm.
•Press the On/Off or Cancel buttons or the
Brake Pedal to return the engine to normal
idle.
To lock the door from inside, rotate the lock
levers as indicated. The deadbolt lock is for added security and should be used as a security night
lock.
Door Latch
Handle
Entrance Door Handle - Inside
Lubricate the locks periodically with graphite
to maintain good working condition.
Screen Door
Latch
ENTRANCE DOOR LOCK
AND HANDLE
The entrance door may be opened from outside the vehicle by pulling the door handle outward. To open the door from inside, pull outward
on the door handle. When the door is locked, neither the inside nor the outside door handle can be
operated. It can be locked and unlocked from the
outside of the vehicle by inserting the key into the
lock and turning, or by using the keyless remote
entry system.
CAUTION
When releasing security night lock,
be sure to retract bolt before opening
door latch to prevent drag on bolt pin.
Instruct all passengers in operation of
this door catch system as well as
emergency exit window.
POWER DOOR LOCK - with
Keyless Remote Entry System
The power door lock controls the side
entrance door.
2-8
Loading...
+ 120 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.