Winnebago Trend (2014), Trend 23B (2014), Trend 23L (2014) User Manual

Download

Rev. 1412150520 Part No. 161500-14-010

5 - DASH / AUTO

TABLE OF CONTENTS

1 – INTRODUCTION

About this Manual ............................................................................................................................ 1-1

Safety Messages Used in this Manual .............................................................................................. 1-1

Pre-Delivery Inspection ....................................................................................................................1-2

Front Axle Tire Alignment ............................................................................................................... 1-2

Service and Assistance ...................................................................................................................... 1-2

Reporting Safety Defects .................................................................................................................. 1-2

Occupant and Cargo Carrying Capacity Labels ............................................................................... 1-3

Vehicle Certification Label ............................................................................................................... 1-4

Specifications and Capacities ........................................................................................................... 1-5

Owner and Vehicle Information ....................................................................................................... 1-6

2 – SAFETY AND PRECAUTIONS

General Warnings ............................................................................................................................. 2-1

Driving Safety ................................................................................................................................... 2-1

Fuel and Propane Gas ....................................................................................................................... 2-2

Propane Gas Leaks ............................................................................................................................ 2-3

Propane Gas Leak Detector .............................................................................................................. 2-3

Carbon Monoxide Warning .............................................................................................................. 2-4

Carbon Monoxide Alarm .................................................................................................................. 2-4

Smoke Alarm .................................................................................................................................... 2-5

Fire Extinguisher ............................................................................................................................... 2-5

Electrical ........................................................................................................................................... 2-6

Loading ............................................................................................................................................. 2-6

Maintenance ...................................................................................................................................... 2-6

Emergency Exits ............................................................................................................................... 2-6

Formaldehyde Information ............................................................................................................... 2-7

Mold, Moisture, and Your Motorhome ............................................................................................ 2-7

Roof .................................................................................................................................................. 2-8

Roadside Emergency ........................................................................................................................ 2-8

Jump Starting ....................................................................................................................................2-9

Engine Overheat ............................................................................................................................. 2-10

5 - DASH / AUTO

3 – DRIVING YOUR MOTORHOME

Seats – Driver/Co-Pilot ..................................................................................................................... 3-1

Seat Belts .......................................................................................................................................... 3-2

Child Restraints ................................................................................................................................. 3-3

Keys .................................................................................................................................................. 3-5

Remote Keyless Entry ...................................................................................................................... 3-5

Hazard Warning Flashers .................................................................................................................. 3-5

Air Conditioner/Heater – Automotive (Dash) .................................................................................. 3-5

Rearview Mirror with Monitor System ............................................................................................3-5

Table Of Contents

Radio – In-Dash ................................................................................................................................3-6

Battery Boost Switch ........................................................................................................................ 3-6

Engine Cooling System .................................................................................................................... 3-6

Lights ................................................................................................................................................ 3-6

Tires .................................................................................................................................................. 3-6

Suspension Alignment and Tire Balance ..........................................................................................3-6

4 – APPLIANCES AND SYSTEMS

Refrigerator ....................................................................................................................................... 4-1

Refrigerator Service Access Compartment ....................................................................................... 4-2

Range Top ......................................................................................................................................... 4-3

Microwave Oven ............................................................................................................................... 4-4

OnePlace® Systems Monitor Panel .................................................................................................. 4-4

Water Heater - Gas Tankless ............................................................................................................ 4-6

Pressure-Temperature Relief Valve (Tankless Water Heater) .......................................................... 4-7

Propane Gas Furnace ........................................................................................................................ 4-7

Roof Air Conditioning - with Heat Strip .......................................................................................... 4-8

Roof Air Conditioning System ......................................................................................................... 4-9

Air Conditioner Filter ....................................................................................................................... 4-9

5 – PROPANE GAS

Propane Gas Supply .......................................................................................................................... 5-1

Safe Use of the Propane Gas System ................................................................................................ 5-2

Propane Gas Warnings and Precautions ...........................................................................................5-3

Propane Gas Pressure Regulator ....................................................................................................... 5-4

Propane Vaporization in Cold Weather ............................................................................................5-5

6 – ELECTRICAL

Electrical Cautions ............................................................................................................................ 6-1

Electrical System – House 120-Volt AC ..........................................................................................6-1

Power Cord – External ...................................................................................................................... 6-1

Power Center ..................................................................................................................................... 6-3

Circuit Breakers – House 120-Volt AC ............................................................................................ 6-4

Electrical Outlets – House 120-Volt AC .......................................................................................... 6-4

Ground Fault Circuit Interrupter ....................................................................................................... 6-4

Electrical Generator – 120-Volt ........................................................................................................ 6-5

Electrical System – House 12-Volt DC ............................................................................................ 6-6

House/Coach Battery Disconnect Switch ......................................................................................... 6-7

Battery Access .................................................................................................................................. 6-7

Battery Care ...................................................................................................................................... 6-8

Circuit Breakers and Fuses – House 12-Volt DC ............................................................................. 6-9

7 – PLUMBING

Fresh Water System .......................................................................................................................... 7-1

Water Pump ...................................................................................................................................... 7-1

Cold Water Filter .............................................................................................................................. 7-3

Disinfecting Your Fresh Water System ............................................................................................ 7-4

Table Of Contents

Shower Hose Vacuum Breaker ......................................................................................................... 7-5

Exterior Shower/Wash Station .......................................................................................................... 7-5

Toilet ................................................................................................................................................. 7-5

Drainage System (P-Traps) ............................................................................................................... 7-6

Waste Water System ......................................................................................................................... 7-6

Holding Tank Heater ........................................................................................................................ 7-7

Waterline & Tank Drain Valves ....................................................................................................... 7-8

Winterizing Procedures ..................................................................................................................... 7-8

Water System Drain Valve Locations ............................................................................................ 7-13

8 – ENTERTAINMENT

TV – 12V LED ................................................................................................................................. 8-1

TV – Galley (Swing-Out) ................................................................................................................. 8-1

Audio-Video System Basic Operation .............................................................................................. 8-2

DVD Player With Deluxe Sound ...................................................................................................... 8-2

Exterior Speakers .............................................................................................................................. 8-3

TV Antenna - Digital ........................................................................................................................ 8-3

TV Signal Amplifier ......................................................................................................................... 8-4

Cable TV and Satellite Connections ................................................................................................. 8-4

Exterior Cable TV - 12V Connection ............................................................................................... 8-5

TV Digital Satellite System Wiring .................................................................................................. 8-5

9 – FURNITURE AND SOFTGOODS

Dinette (Removable Panel) ............................................................................................................... 9-1

Sleeping Facilities ............................................................................................................................. 9-1

Dinette/Bed Conversion .................................................................................................................... 9-2

Dinette/Bed Conversion .................................................................................................................... 9-3

Loft Bed ............................................................................................................................................ 9-5

Bunk Ladder ..................................................................................................................................... 9-6

Loft Bed ............................................................................................................................................ 9-7

Bed - Adjustable ............................................................................................................................... 9-8

Roller Shades (Manual) - Solar/Blackout ......................................................................................... 9-8

Wood Furniture and Cabinetry ......................................................................................................... 9-9

10 – MAINTENANCE AND STORAGE

Sealants – Inspection and General Information .............................................................................. 10-1

Roof ................................................................................................................................................ 10-1

Undercarriage .................................................................................................................................. 10-1

Exterior Automotive Paint Finish ................................................................................................... 10-2

Exterior Graphic Care ..................................................................................................................... 10-4

Plastic Parts – Cleaning .................................................................................................................. 10-4

Exterior Lights ................................................................................................................................ 10-5

Interior Soft Goods ......................................................................................................................... 10-5

Cabinetry – Cleaning ...................................................................................................................... 10-6

Tables and Countertops .................................................................................................................. 10-7

Stainless Steel Appliances .............................................................................................................. 10-7

Table Of Contents

Galley Sink ..................................................................................................................................... 10-8

Range and Refrigerator ................................................................................................................... 10-8

Vinyl Flooring ................................................................................................................................. 10-8

Bathroom ........................................................................................................................................ 10-9

Doors and Windows ........................................................................................................................ 10-9

Vehicle Storage – Preparation ...................................................................................................... 10-10

Vehicle Storage – Removal .......................................................................................................... 10-10

Chassis Service and Maintenance ................................................................................................. 10-11

Coach Maintenance Chart ............................................................................................................. 10-12

11 – MISCELLANEOUS

Loading the Vehicle ........................................................................................................................ 11-1

Weighing Your Loaded Vehicle ..................................................................................................... 11-1

Car or Trailer Towing ..................................................................................................................... 11-3

Trailer Wiring Connector ................................................................................................................ 11-4

Towing Guidelines .......................................................................................................................... 11-4

Entry Step – Electric ....................................................................................................................... 11-5

Power Roof Ventilator .................................................................................................................... 11-6

Power Awning ................................................................................................................................ 11-7

Effects of Prolonged Occupancy .................................................................................................... 11-7

SECTION 1 – INTRODUCTION

DA NG E R

Congratulations! We welcome you to the exciting world of motorhome travel and camping. You will find it convenient and enjoyable to have all the comforts of home and still enjoy the great outdoors wherever you choose to go.

Before sliding into the driver’s seat, please become familiar with operations and features. In addition, spend some time with the dealer when you take delivery to learn all you can about your new motorhome.

ABOUT THIS MANUAL

This operator’s manual was prepared to aid you in the proper care and operation of the vehicle and equipment.

Please read this manual completely to understand how everything in your coach works before taking it on its “maiden voyage”. In addition, please become familiar with the New Vehicle Limited Warranty.

NOTE: This manual describes many features of

your motorhome and includes instructions for its safe use. This manual, including photographs and illustrations, is of a general nature only.

Some equipment and features described or shown in this manual may be optional or unavailable on your model.

Because of Winnebago Industries continuous program of product improvement, it is possible that recent product changes and information may not be included. The instructions included in this manual are intended as a guide, and in no way extend the responsibilities of Winnebago Industries beyond the standard written warranty as presented in this manual. The descriptions, illustrations, and specifications in this manual were correct at the time of printing. We reserve the right to change specifications or

’

design without notice, and without incurring obligation to install the same on products previously manufactured.

The materials in your InfoCase contain

warranty information and operating and maintenance instructions for the various appliances and components in your motorhome.

NOTE: Many of the instruction sheets and

manuals for the various appliances and components have been incorporated into the Operator’s Manual Supplement for your convenience. Please read the FAQ in Section 1 of the Operator’s Manual Supplement for more details.

Throughout this manual, frequent reference is made to the vehicle chassis manual that is provided by the manufacturer of the chassis on which this motorhome is built.

Consult the chassis manual for operating, safety, and maintenance instructions pertaining to the chassis section of the motorhome.

SAFETY MESSAGES USED IN THIS MANUAL

Throughout this manual, certain items are labeled Danger, Warning, Caution, Notice, or Note. These terms alert you to precautions that may involve damage to your vehicle or a risk to your personal safety. Read and follow them carefully.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious personal injury.

5 - DASH / AUTO

1-1

SECTION 1 –

WARNING

CAUTION

INTRODUCTION

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious personal injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate personal injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

NOTE: A “Note” is not necessarily safety-

related, but indicates a recommendation or special point of information that could assist in understanding the use or care of a feature item.

FRONT AXLE TIRE ALIGNMENT

We recommend that you have the front suspension and steering alignment checked and adjusted after you have fully loaded the vehicle according to your needs. Thereafter, have alignment inspected periodically to maintain vehicle steering performance and prevent uneven tire wear.

SERVICE AND ASSISTANCE

Your dealer will be glad to provide any additional information you need, as well as answer any questions you might have about operating the equipment in your coach. When it comes to service, remember that your dealer knows your vehicle best and is interested in your satisfaction. Your dealer will provide quality maintenance and any other assistance that you may require during your ownership of this vehicle.

If you need warranty repairs while traveling, you may take your vehicle to any authorized Winnebago Industries® dealership and request their assistance.

See the Service Dealer Directory in your InfoCase.

PRE-DELIVERY INSPECTION

This motorhome has been thoroughly inspected before shipment. Your dealer is responsible for performing a complete predelivery inspection of the chassis and all motorhome components.

As a part of the pre-delivery inspection procedure, the dealer is responsible for road testing the motorhome, noting, and correcting any problems before delivery.

1-2

REPORTING SAFETY DEFECTS

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Winnebago Industries, Inc.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Winnebago Industries®.

To contact NHTSA, you may either call the Vehicle Safety Hotline toll-free at: 1-888-327-4236; (TTY: 1-800-424-9153)

or go to their website at http://www.safercar.gov or write to:

Administrator, NHTSA 1200 New Jersey Avenue S.E. Washington, D.C. 20590

You can also obtain other information about motor vehicle safety from the NHTSA website at http://www.safercar.gov

OCCUPANT AND CARGO CARRYING CAPACITY LABELS

The following labels are affixed on the driver’s door jamb. The first label contains vehicle occupant and cargo carrying capacity along with the number of seat belt positions in the vehicle. The second label also provides the weight of a full load of water and advises that this weight, along with the tongue weight counts as cargo.

SECTION 1 –

INTRODUCTION

If any weight exceeding 45.4 kg (100 lbs.) is added to your coach between final vehicle certification and first retail sale, the occupant and cargo carrying capacity must be corrected and a label similar to the one shown below will be affixed inside your coach.

1-3

SECTION 1 – INTRODUCTION

VEHICLE CERTIFICATION LABEL

This label is affixed to the lower driver side armrest panel, driver door, or the driver side door jamb,

depending on model. It contains vehicle identification numbers and other important reference information.

EXPLANATION OF DATA

1. Chassis manufacturer.

2. Chassis manufacture date.

3. Month and year of manufacture at Winnebago Industries®.

4. Gross Vehicle Weight Rating: Total permissible weight of the vehicle, including driver, passengers, total cargo carried (including all liquids), and equipped with all options.

5. Gross Axle W eight Rating: Total permissible weight allowed for the front and rear axles (listed in pounds and kilograms).

6. Suitable Tire Choice: Tires recommended to meet handling and safety requirements. When replacing any of the tires on your vehicle, always replace with a tire that meets these specifications.

7. Suitable Rim Choice: Wheel rims recommended to meet handling and safety requirements. When replacing any of the rims on your vehicle, always replace with a rim that meets these specifications.

8. Cold Inflation Pressure: Inflation pressures at Gross Axle Weight Ratings recommended (while cold) for the tires originally equipped

on your vehicle. These pressure levels must be maintained to assure proper handling, safety, and fuel economy.

9. Rear Axle Wheel Configuration: Single or Dual as it relates to the inflation.

10. Serial Number: This is the serial number assigned to the completed vehicle by Winnebago Industries.

11. Vehicle Identification Number (VIN): This number identifies the chassis on which the motorhome is built. The 10th digit of the VIN designates the chassis model year. (C=2012, D=2013, E=2014, etc.). This information is useful when ordering chassis repair parts.

12. Type: States the NHTSA designated usage classification for your motorhome. MPV signifies a Multi-purpose Passenger Vehicle.

13. Color: Signifies the color code number of the decor used throughout the vehicle. This number is necessary for ordering replacement cushions, curtains, carpet, etc.

14. Winnebago

model year and series/family

name.

15. Model: Lists the Winnebago product model number of your vehicle.

1-4

SPECIFICATIONS AND CAPACITIES

24J 24M

Mercedes-

Benz

Sprinter Cab

Chassis

Mercedes-

Benz

Sprinter Cab

Chassis

Feature Number 1MP 1MP

Length 24' 5.7" 24' 5.7"

Exterior Height

11' 3" 11' 3"

Exterior Width 7' 6.25" 7' 6.25"

Exterior Storage

43.1 cu. ft. 37.4 cu. ft.

Awning Length 15' 15'

Interior Height 6' 8" 6' 8"

Interior Width 7' 3" 7' 3"

29 gal. 32 gal.

Water Heater Capacity 6 gal. 6 gal.

29 gal. 32 gal.

Holding Tank Capacity - Gray

35 gal. 36 gal.

13 gal. 13 gal.

Wheelbase 170" 170"

GVWR 11,030 lbs. 11,030 lbs.

GAWR - Front 4,410 lbs. 4,410 lbs.

GAWR - Rear 7,720 lbs. 7,720 lbs.

GCWR

15,250 lbs. 15,250 lbs.

Fuel Capacity

100 liter

( 26.4 gal.)

100 liter

( 26.4 gal.)

Actual towing capacity is dependent on your particular loading and towing circumstances which includes the GVWR, GAWR,

and GCWR as well as adequate trailer brakes. Refer to the chassis operator's manual of your motor home for further towing

Capacities shown are the tank manufacturer's listed water capacity (W.C.). Actual filled propane capacity is 80% of listing due

All information is based upon the most recent data available. Visit the W innebago Industries, Inc. web page – www.winnebagoind.com – for the most current product information.

The height of each model is measured to the top of the tallest standard feature and is based on the curb weight of a typically

equipped unit. The actual height of your vehicle may vary by several inches depending on chassis or equipment variations.

The load capacity of your motor home is designated by weight, not by volume, so you cannot necessarily use all available space

when loading your motor home.

Capacities are based on measurements prior to tank installation. Slight capacity variations can result upon installation.

23B 23L

Ram

ProMaster

Cab Chassis

Ram

ProMaster

Cab Chassis

Feature Number 1KG 1KG

Length 24' 24'

10' 1" 10' 1"

Exterior Width 7' 6.25" 7' 6.25"

Exterior Storage

15.8 cu. ft. 35.0 cu. ft.

Awning Length 15' 15'

Interior Height 6' 7" 6' 7"

Interior Width 7' 3" 7' 3"

27 gal. 26 gal.

Water Heater Capacity Continuous Continuous

40 gal. 32 gal.

32 gal. 40 gal.

13 gal. 13 gal.

Wheelbase 159" 159"

GVWR 9,350 lbs. 9,350 lbs.

GAWR - Front 4,630 lbs. 4,630 lbs.

GAWR - Rear 5,291 lbs. 5,291 lbs.

11,500 lbs. 11,500 lbs.

Fuel Capacity 24 gal. 24 gal.

For vehicles manufactured 5/27/14 or later.

Actual towing capacity is dependent on your particular loading and towing circumstances which includes the GVWR, GAWR,

and GCWR as well as adequate trailer brakes. Refer to the chassis operator's manual of your motor home for further towing

Capacities shown are the tank manufacturer's listed water capacity (W.C.). Actual filled propane capacity is 80% of listing due

to overfilling prevention device on tank.

All information is based upon the most recent data available. Visit the W innebago Industries, Inc. web page – www.winnebagoind.com – for the most current product information.

The height of each model is measured to the top of the tallest standard feature and is based on the curb weight of a typically

equipped unit. The actual height of your vehicle may vary by several inches depending on chassis or equipment variations.

The load capacity of your motor home is designated by weight, not by volume, so you cannot necessarily use all available

space when loading your motor home.

Capacities are based on measurements prior to tank installation. Slight capacity variations can result upon installation.

Exterior Height

SECTION 1 –

INTRODUCTION

9' 11"

Freshwater Tank Capacity

Holding Tank Capacity - Black

Propane Capacity

Holding Tank Capacity - Gray

Propane Capacity

GCWR

Notes:

Contact your dealer for further information.

9' 11"

to overfilling prevention device on tank.

information.

1-5

SECTION 1 – INTRODUCTION

OWNER AND VEHICLE INFORMATION

OWNER INFO

Owner’s Name(s) __________________________________________________________________ Address __________________________________________________________________________

__________________________________________________________________________

VEHICLE INFORMATION

Motorhome Model Number __________________________________________________________ Motorhome Serial Number___________________________________________________________ Chassis Vehicle Identification No. (VIN)________________________________________________ Vehicle Mileage at Delivery __________________________________________________________ Selling Dealer Name________________________________________________________________ Address __________________________________________________________________________

__________________________________________________________________________

YOUR WINNEBAGO INDUSTRIES® DEALER /SERVICE CENTER

Name____________________________________________________________________________ Address __________________________________________________________________________

__________________________________________________________________________

Contact ____________________________________________Phone ________________________

CHASSIS SERVICE CENTER

Name____________________________________________________________________________ Address __________________________________________________________________________

__________________________________________________________________________

Contact ____________________________________________Phone ________________________

RV INSURANCE POLICY

Company_________________________________________________________________________ Policy Number ____________________________________________________________________ Agent______________________________________________Phone ________________________

1-6

SECTION 2 – SAFETY AND PRECAUTIONS

WARNING

GENERAL WARNINGS

• Only seats equipped with seat belts are to be occupied while the vehicle is moving.

• Make sure all passengers have seat belts fastened. Lap belts should fit low on the hips and upper thighs. The shoulder belt should be positioned snug over the shoulder.

• For pregnant women: Never place the shoulder belt behind your back or under your arm. Adjust the lap belt across your hips/ pelvis, and below your belly. Place the shoulder belt across your chest (between your breasts) and away from your neck.

• Child restraints should be installed properly according to manufacturer’s instructions. See “Child Restraints”.

• All moveable or swiveling seats should be placed and locked in travel position while the vehicle is moving.

• Never let passengers stand or kneel on seats while the vehicle is moving.

• Sleeping facilities are not to be utilized while vehicle is moving.

• Examine the escape window and be familiar with its operation.

• Inspect the fire extinguisher monthly for proper charge and operating condition. This should also be done before beginning a vacation or any extended trip.

DRIVING SAFETY

This motorhome has been designed, manufactured and tested with concern for the protection of it’s occupants. We recommend you perform the following inspections for your safety and the safety of your passengers before starting your vehicle.

1. LP GAS SYSTEM - Turn off at tank for traveling. Test for leaks upon arrival at destination before lighting pilots.

2. WHEELS - Inspect for damage and check lug nuts for tightness.

3. TIRES - Inspect for wear and damage and check for recommended air pressure.

4. LIGHTING - Test for proper operation of all interior and exterior lights including dash lights, headlights, tail lights, brake lights, clearance lights, and turn signals.

5. EXITS - Inspect release mechanism on emergency exit window, test both locks on main entrance door for ease of operation and instruct passengers how to use both means of exit.

6. SEAT BELTS - Direct passengers to designated seats, be certain swivel seats are locked into position, and require use of a seat belt. See operator’s manual for occupancy and weight restrictions.

7. APPLIANCES - Turn off and latch or lock doors where provided.

8. LOOSE PARCELS - Store securely.

9. UTILITY SUPPL Y LINES - Disconnect all electrical, sewer and water lines and secure properly.

10. ENTRANCE DOOR STEP - Assure step is in retracted position for traveling.

Read your motorhome and chassis owner’s manual for further precautions.

5 - DASH / AUTO

• Do not attempt to adjust the driver’s seat while the vehicle is moving.

2-1

SECTION 2 –

DA NG E R

WARNING

SAFETY AND PRECAUTIONS

• Do not adjust tilt steering in a moving vehicle.

• Do not operate the cruise control on icy or extremely wet roads, winding roads, in heavy traffic, or in any other traffic situation where a constant speed cannot be maintained.

• Use care when accelerating or decelerating on a slippery surface. Abrupt speed changes can cause skidding and loss of control.

• Never drive the vehicle with a slideout room extended.

• Driving through water deep enough to wet the brakes may affect stopping distance or cause the vehicle to pull to one side. Check brake operation in a safe area to be sure they have not been affected. Never operate any vehicle if a difference in braking efficiency is noticeable.

• Adverse weather conditions and extremes in terrain may affect handling and/or performance of your vehicle. Refer to your chassis manual for complete and related information on driving your vehicle.

FUEL AND PROPANE GAS

All pilot lights, appliances, and their ignitors (see operating instructions) shall be turned off before refueling of motor fuel tanks and/or propane containers. Failure to comply could result in death or serious injury.

Propane gas containers, gasoline, or other flammable liquids shall not be placed or stored onboard the vehicle because a fire or explosion may result. Propane gas containers are equipped with safety valves, which relieve excessive pressure by discharging gas to the atmosphere. Failure to comply could result in death or serious injury.

• All pilot lights must be extinguished and appliances turned off while refilling the fuel tank or propane gas tank.

• Never smoke while refilling vehicle fuel tank or propane gas tank.

• Never use an open flame to test for propane gas leaks. Replace all protective covers and caps on propane system after filling. Make sure valve is closed and the door is latched securely.

• Never connect natural gas to the propane gas system.

• When lighting range burners, do not turn burner controls to “On” and allow gas to escape before lighting match.

• Portable fuel-burning equipment, including wood and charcoal grills and stoves shall not be used inside the recreational vehicle. The use of this equipment inside the recreational vehicle may cause fires or asphyxiation.

• Propane gas regulators must always be installed with the diaphragm vent facing downward. Regulators are equipped with a protective cover. Make sure that the regulator vent faces downward and that the cover is kept in place to minimize vent blockage, which could result in excessive gas pressure causing fire or explosion.

2-2

• The following warning label is located in the cooking area to remind you to provide an adequate supply of fresh air for combustion.

DA NG E R

Do not use gas cooking appliances for

WARNING

Propane Gas Leak Detector

comfort heating. May lead to carbon monoxide poisoning, which can lead to death or serious injury.

Gas cooking appliances need fresh air for safe operation. Before operating: Open vents or windows slightly or turn on exhaust fan prior to using cooking appliance. Gas flames consume oxygen, which should be replaced to ensure proper combustion. Improper use may result in death or serious injury.

SECTION 2 –

SAFETY AND PRECAUTIONS

• Open doors and other ventilating openings.

• Leave the area until odor clears.

• Have the propane system checked and leakage source corrected before using again.

Failure to comply could result in death or

serious injury.

PROPANE GAS LEAK DETECTOR

Your coach is equipped with a Propane Gas Leak Detector, similar to the one shown below. The leak detector sounds an alarm if an unsafe amount of propane gas is present inside the coach.

Unlike homes, the amount of oxygen supply is limited due to the size of the recreational vehicle, and proper ventilation when using the cooking appliance(s) avoids dangers of asphyxiation. It is especially important that cooking appliances not be used for comfort heating, as the danger of asphyxiation is greater when the appliance is used for long periods of time. Failure to comply could result in death or serious injury.

PROPANE GAS LEAKS

Check propane gas system for leaks yearly, or as necessary.

The following procedures are noted on a label, located in the vehicle near the range area. If you smell gas within the vehicle, quickly and carefully perform the procedures listed.

IF YOU SMELL PROPANE

• Extinguish any open flames, pilot lights, and

all smoking materials.

• Do not touch electrical switches.

• Shut off the gas supply at the tank valve(s) or

gas supply connection.

EXPLOSION HAZARD: DO NOT use an open flame to test for gas leaks. When testing for gas line leaks with a soapy water solution, DO NOT use a detergent containing ammonia or chlorine. These substances may generate a chemical reaction causing corrosion to gas lines, resulting in dangerous leak conditions. Death or serious injury can result.

Power Connection

The Propane Gas Leak Detector is powered by the house batteries. If the House/Coach Battery Disconnect switch is shut off or the battery cable is disconnected from the batteries, the alarm will

2-3

SECTION 2 –

WARNING

Press button to test

Carbon Monoxide Alarm

SAFETY AND PRECAUTIONS

not work. The Propane Gas Leak Detector fuse or circuit breaker is located in the 12-volt house electrical load center.

Because the Propane Gas Leak Detector is connected to the house battery, it is always drawing a small amount of current. Even though this current draw is slight, it could drain the house battery during storage periods when the house battery will not be charged regularly by the engine or shoreline.

Replacement

When replacing this alarm, we recommend replacing only with the same model, or with one that is also listed for RV application. We recommend obtaining a replacement from your Winnebago Industries® dealer.

Further Information

See the manufacturer’s user guide provided in your InfoCase for further instructions.

To allow proper operation of the vehicle’s ventilation system, keep front ventilation inlet grill clear of snow, leaves, or other obstructions at all times. DO NOT OCCUPY A PARKED VEHICLE WITH ENGINE RUNNING FOR AN EXTENDED PERIOD.

Do not run engine in confined areas, such as a garage, except to move vehicle into or out of the area.

CARBON MONOXIDE ALARM

Your coach is equipped with a Carbon Monoxide (CO) Alarm, which has a sensor that is designed to detect toxic carbon monoxide gas fumes resulting from incomplete combustion of fuel. It will detect CO gas from any combustion source such as the furnace, gas range/oven, water heater, refrigerator, chassis engine, and electric generator engine.

CARBON MONOXIDE WARNING

Avoid inhaling exhaust gases, as they contain carbon monoxide, which is a colorless, odorless, and poisonous gas. Death or serious injury can result.

The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust and ventilation system. It is recommended that the exhaust system and body be inspected by a qualified motorhome service center:

• Each time the vehicle is serviced for an oil

change.

• Whenever a change in the sound of the

exhaust system is noticed.

Failure to replace this product by the “REPLACE BY DATE” printed on the alarm cover may result in death by Carbon Monoxide poisoning.

• Whenever the exhaust system, underbody , or

rear of the vehicle is damaged.

2-4

SECTION 2 –

WARNING

Smoke Alarm

Push button

to test

Fire Extinguisher

(Typical installation - your

coach may vary according

to model and floorplan)

SAFETY AND PRECAUTIONS

Replacement

Further Information

Please read the information provided by the manufacturer, which is included in your InfoCase for further information.

SMOKE ALARM

Your coach is equipped with a Smoke Alarm (located on the ceiling in the lounge area.) The Smoke Alarm is powered by a 9-volt battery and has a sensor that is designed to detect smoke.

Replacement

Further Information

See the manufacturer’s information in your InfoCase for further instructions.

FIRE EXTINGUISHER

A dry chemical Fire Extinguisher is located near the main entrance door.

The following label is affixed to the Smoke

Alarm.

Test smoke alarm operation after vehicle has been in storage, before each trip, and at least once per week during use. Failure to do so may result in death or serious injury.

We recommend that you become thoroughly familiar with the operating instructions displayed on the side of the Fire Extinguisher and in the information supplied in your InfoCase.

We also recommend that you inspect the Fire Extinguisher for proper charge at least once a month in accordance with National Fire Protection Association (NFPA) recommendations as stated on the label.

If the charge is insufficient, the Fire Extinguisher must be replaced.

2-5

SECTION 2 – SAFETY AND PRECAUTIONS

NOTICE

Do not test the fire extinguisher by discharging it. Partial discharge can cause leakage of pressure or contents, which would render the unit inoperative when needed. When using the fire extinguisher , aim the spray at the base of the fire.

Replacement

If for any reason you must replace the Fire Extinguisher, the replacement must be the same type and size as the one originally supplied in your coach. We recommend obtaining a replacement only from your Winnebago Industries® dealer or a reliable RV parts supplier.

ELECTRICAL

• Careless handling of electrical components

can be fatal. Never touch or use electrical components or appliances while feet are bare, while hands are wet, or while standing in water or on wet ground.

• Improper grounding of the vehicle can cause

personal injury . Do not plug the utility power cord into an outlet which is not grounded and do not adapt the plug to connect to a receptacle for which it is not designed.

• Do not attach an extension cord to the utility

power cord.

• Do not use any electrical device that has had

the ground pin removed.

• A void overloading electrical circuits. Replace

fuses or circuit breakers with those of the same size and amperage rating only. Never use a higher rated fuse or breaker.

• Use caution when handling or working near

electrical storage batteries. Always remove jewelry and wear protective clothing and eye covering. Avoid creating sparks.

• Store or secure all loose items inside the motorhome before traveling. Possible overlooked items such as canned goods or small appliances on the countertop, cooking pans on the range, or free-standing furniture items can become dangerous projectiles during a sudden stop.

• Be aware of GVWR, GAWR, and individual load limit on each tire or set of duals (See “Loading the Vehicle” in Section 12 - Miscellaneous).

• Never load the motorhome in excess of the gross vehicle weight rating or the gross axle weight rating for either axle.

MAINTENANCE

• Do not remove the radiator cap while engine and radiator are still hot. Always check coolant level visually at the see-through coolant reservoir.

• Never get beneath a vehicle that is held up by a jack only.

• Do not mix different construction types of tires on the vehicle, such as radial, bias, or belted tires, as vehicle handling may be affected. Replace tires with exact size, type, and load range.

EMERGENCY EXITS

Escape Window

The bedroom escape window is secured by two red safety latches at the bottom or side of the window.

To open, lift both latches up and toward the center of the window, then push outward near the bottom of the window.

2-6

Using Slider Windows As

Escape Window

Pull Red Handles Up and Push Window Out.

-Typical View

Slider Window Latch

(Lift latch UP and slide window open)

-Typical View

Emergency Exits

Some coaches are required to have a slider window as an alternate exit. This window will be marked EXIT and have a red-handled latch.

SECTION 2 –

SAFETY AND PRECAUTIONS

FORMALDEHYDE INFORMATION

Some of the materials used in this recreational vehicle emit formaldehyde. Eye, nose, and throat irritation, headache, nausea, and a variety of asthma-like symptoms, including shortness of breath have been reported as a result of formaldehyde exposure. Reaction to formaldehyde exposure may vary among individuals. Elderly persons and young children, as well as anyone with a history of asthma, allergies, or lung problems may be at greater risk. Research is continuing on the possible long-term effects of exposure to formaldehyde. Inadequate ventilation may allow formaldehyde and other contaminants to accumulate in indoor air. Ventilation to dilute the indoor air may be obtained from a passive or mechanical ventilation system. Always be sure to thoroughly ventilate your recreational vehicle before and during each use. High indoor temperatures and humidity may raise formaldehyde levels. When a recreational vehicle is in areas subject to high temperatures, an air conditioning system can be used to control indoor temperature levels. If you have any questions regarding the health effects of formaldehyde, consult your doctor or local health department.

Most slider windows along the side of any motorhome can also be used as alternate emergency exits, should the need arise.

To use slider windows as an exit:

• Lift window latch UP.

• Slide the window open.

• Either slide the screen open or push the screen

material out, depending on window construction.

MOLD, MOISTURE, AND YOUR MOTORHOME

What is Mold?

Molds are part of the natural environment. They are as old as the Earth itself and mold spores are almost everywhere at some level waiting to grow. Mold plays a part of nature by breaking down dead organic matter, such as fallen leaves and dead trees. Indoors however, mold growth should be avoided. Molds reproduce by means of tiny spores. Those spores are invisible to the naked eye and float throughout the outdoor and indoor air. Because of the nature of the use of a motorhome, it is natural for a motorhome to be introduced into an environment with mold spores.

2-7

SECTION 2 –

WARNING

SAFETY AND PRECAUTIONS

Mold is a plant and requires its own special environment to grow. That environment includes organic materials, nutrients, moisture, and proper temperature.

How Can I Avoid Mold?

To reduce the ability for mold to grow, you must reduce what constitutes its growth environment. Mold can grow with the smallest of a nutrient base. Just small amounts of dirt or dust on the carpet can be enough to allow the mold process to begin. Keep the environment as clean as possible. Vacuum the carpet. Clean food spills thoroughly and quickly. Avoid grease buildup near the stove or sink. Clean the exhaust fan above the stove often.

Minimize moisture in your motorhome and keep humidity low. Clean spills quickly. Do not allow condensation to build up. You can open windows and vents to minimize condensation. Use of the air conditioner can assist in removing moisture from the air. Avoid leaks, but if leaks do occur, make repairs promptly.

Avoid bringing mold into your motorhome. Plants, cloths, books, and other household items may already have mold present. It is easy to transfer mold into your motorhome environment.

Monitor your motorhome. Periodically check those hidden areas in corners, closets, and cabinets to assure mold is not present.

What if I Find Mold?

If mold develops, clean the area with a concentrate of soap and bleach. Items that contain mold that cannot be cleaned should be removed from the vehicle.

Can Mold Harm Me?

The effects of mold and airborne mold spores may cause irritation to some people. Experts disagree on the level of exposure that may cause health concerns.

If Mold Is Present, What Will

Winnebago Industries

If Winnebago Industries determines that mold is present in the Winnebago®/Itasca® motorhome as a result of a manufacturing defect reported to Winnebago Industries within the limited warranty period, Winnebago will clean the affected area(s) and/or replace affected items as it deems necessary. This is the extent of coverage provided by Winnebago Industries. Winnebago Industries, however, will not assume responsibility for mold deemed to be a result of a motorhome users lack of timely and appropriate action to mitigate circumstances should a problem occur.

If Winnebago Industries determines that mold is present due to conditions it determines is not a result of a manufacturing defect found within the warranty period, Winnebago Industries will not provide any financial assistance to the repair of the condition.

Do?

ROOF

STAY OFF ROOF. Surface may be slippery. Falling could result in death or serious injury.

Walking or working on the roof should be left to qualified service personnel using proper safety equipment in a safe environment. You should only walk or work on the roof if you are qualified and have created a safe environment.

For your safety, it is not recommended that you store or carry items on the roof.

ROADSIDE EMERGENCY

Because of the size and weight of this vehicle and its tires, and the possible complications involved in tire changing, we strongly advise obtaining professional road service to change a flat tire whenever possible. However, if an

2-8

SECTION 2 –

WARNING

SAFETY AND PRECAUTIONS

emergency requires you to change the tire yourself, please exercise extreme caution and read all tire changing information in the chassis manual.

Never get beneath a vehicle that is held up by

a jack only.

If You Get A Flat Tire

• DO NOT panic.

• Grip the steering wheel firmly and steer the vehicle as straight as possible. Avoid quick maneuvers. You may need to counter-steer to compensate for “pull” created by the failed tire.

• DO NOT stomp on the brake. This abruptly shifts the vehicle’s weight forward, making it nose-dive and pull toward the blown-out side.

• DO NOT jerk your foot off the accelerator. Just ease back on the accelerator slowly and gently to continue momentum. The deflated tire will slow the vehicle.

• If you must change lanes to get to a safe stopping place, use your signals to warn other motorists and change lanes smoothly and carefully after you are certain the lane is clear .

• Let the vehicle coast to a stop, gently steering to a safe stopping place off the traffic lanes of the road. Do not worry about damaging the tire or wheel rim by driving on it. A tire or wheel replacement is cheaper than damaging the vehicle or injuring yourself.

• When you have come to a stop, activate your hazard flashers to warn other motorists, then exit the vehicle carefully.

• Set out flares or other warning devices.

Winnebago Industries® does not assume responsibility for damage incurred while towing this vehicle.

NOTE: Consult your chassis manual for towing

instructions or precautions provided by the chassis manufacturer.

NOTICE

Do not lift on bumper . Damage will result to front end body parts.

Stay out from beneath the motorhome while it is suspended by the towing assembly. Do not allow passengers to occupy a towed vehicle. Death or serious injury can result.

JUMP STARTING

If your coach will not start from the chassis battery, try using the Battery Boost switch to divert power from the house batteries to the starter. (See “Battery Boost Switch” in Section 3

- Driving Your Motor Home).

If you wish to try jump starting the engine using another vehicle or booster system, see your chassis manual for connecting jumper cables to the automotive electrical system.

Check your tires for proper inflation before each trip and at least once a month with an accurate tire gauge.

Recovery Towing

When calling a professional towing service, we recommend that you advise them of your coach length and approximate front axle weight listed on your Vehicle Certification Label. This will allow the towing operator to determine the proper towing equipment to use.

NOTICE

Do not attempt to push start this vehicle. Damage to the transmission or other parts of the vehicle will occur.

2-9

SECTION 2 – SAFETY AND PRECAUTIONS

ENGINE OVERHEAT

If you see or hear steam escaping from the engine compartment or have any other reason to suspect an extreme engine overheating condition, pull the vehicle over to the roadside as soon as it is safe to do so, stop the engine, and get all passengers out of the vehicle.

NOTICE

Operating a vehicle under a severe overheating condition can result in damage to the vehicle.

For information on what to do in case of overheating, consult your chassis manual.

2-10

SECTION 3 – DRIVING YOUR MOTORHOME

WARNING

Lumbar

Control

Seat

Recline

Front Height

Control

Driver Seat

-Typical View

Rear Height

Control

Swivel

Driver Seat

-Typical View

Forward and Rearward

Adjusting Bar

The information in this section refers only to features installed or adapted to the dash and driver compartment area by Winnebago Industries®. It also includes passenger seating in the living area of the coach.

Further Information

See the chassis manual in your InfoCase for all original chassis related controls, instrumentation, switches, and other features. This includes items such as cruise control, climate controls, gauges, wipers, lights, front seats, and three-point safety belts, etc.

SEATS – DRIVER/CO-PILOT

The driver and co-pilot seats may be independently adjusted to suit individual preference.

The seats may be swiveled to provide easy entrance and exit. The swivel feature also allows the seats on most models to be turned toward the living area for additional seating while the unit is parked.

• Seat Recline - Lift up on the lever to operate.

• Front and Rear Height Control - Rotate the

knob to adjust the seat up or down.

• Lumbar Control - Rotate the knob forward

to increase and rearward to decrease the desired amount of lumbar support.

Assure seat is in its forward and locked position for travel. Do not adjust seat while vehicle is in motion. Failure to comply may result in injuries.

5 - DASH / AUTO

• Swivel - Lift up on the lever to operate.

• Forward and Rearward Adjusting Bar -

Pull the bar upward to move the seat forward or rearward. Release at the desired position.

3-1

SECTION 3 –

-Typical View

Armrest

Height

Adjuster

WARNING

1- Insert tab into buckle slot until it “clicks” and is locked

2- Pull strap to tighten

3- Press to

release

DRIVING YOUR MOTORHOME Armrest Adjustment

The armrests may be swung upward out of the way for easy exit or access to the front seats. A roller on the underside of the front of the armrest also lets you adjust the resting angle for personal comfort, whether the seat is upright or reclined.

seat mechanism. After any serious accident, any seat belts which were in use at the time must be inspected and replaced if necessary.

Adjustment

To lengthen belt, swivel the tab end at a right angle to belt and pull strap to desired length. To shorten, pull loose end of belt.

Further Information

See the chassis manual in your InfoCase for

instructions on seat adjustments.

SEAT BELTS

Seats intended for occupancy while the vehicle is in motion are equipped with seat belts for the protection of the driver and passengers.

Lap/Shoulder Belts

(Driver/Co-Pilot Seats)

See your chassis manual for instructions on proper fastening, adjustment, and releasing of lap/shoulder belts.

Lap Belts

(Sofa)

The lap belts must be worn as low as possible and fit snugly across the hip area. Always sit erect and well back into the seat. To gain full protection of the safety belt, never let more than one person use the same safety belt at any one time, and do not let the safety belts become damaged by pinching them in the doors or in the

To Fasten

Be sure belt is not twisted. Grasp each part of the belt assembly and push tongue into buckle. Adjust to a snug fit by pulling the loose end away from the tongue.

To Release

Press button in center of buckle and slide tongue out of buckle.

Snug and low belt positions are essential. This will ensure that the force exerted by the lap belt in a collision is spread over the strong hip area and not across the abdomen, which could result in serious injury. Only seats equipped with seat belts are to be occupied while vehicle is in motion. Swivel seats must be in the locked, forward facing position while vehicle is in motion.

3-2

SECTION 3 –

WARNING

1- Insert tab into buckle slot

until it “clicks” and is locked

2- Press to release

DRIVING YOUR MOTORHOME

Lap/Shoulder Belts

(Dinette)

Fastening

Hold the belt just behind the tongue. Next, bring the belt across the body and insert the tongue into the buckle until the latch engages.

Unfastening

Press the release button in the buckle. Hold onto the tongue when you release it from the buckle to keep it from retracting too rapidly.

When the lap-shoulder belt is in use, the lap belt must ride low across the hip area and the shoulder belt must ride diagonally over the shoulder toward the buckle.

The shoulder belt is designed to lock only during a sudden stop, sudden body movement or a collision. At all other times it will move freely with the occupant.

Never wear the shoulder belt in any position other than as stated above. Failure to do so could increase the chance or extent of injury in a collision.

Seat Belt Care and Cleaning

• Be careful not to damage the belt webbing and hardware. Take care not to pinch them in the seat or doors.

• Inspect the belts and hardware periodically. Check for cuts, frays, and loose parts. Damaged parts should be replaced. Do not remove or modify the belt system.

• Keep belts clean and dry. If the belts need cleaning, use only a mild soap and water solution. Do not use hot water. Do not use abrasive cleaners, bleach, or dyes. These products may weaken the belts.

• Replace any belt assembly that was used during a severe impact. Replace the complete assembly even if damage is not apparent.

CHILD RESTRAINTS

-If Equipped

A properly installed and secured child restraint system can help reduce the chance or severity of personal injury to a child in an accident or during a sudden maneuver. Children may have a greater chance of being injured in an accident if they are seated in a child restraint system which is not properly secured.

A child restraint system is designed to be secured in a vehicle seat by a lap belt or the lap belt portion of a lap-shoulder belt.

When purchasing a child restraint system, follow these guidelines:

1. Look for the label certifying that it meets all

applicable safety standards.

2. Make sure that it will attach to your vehicle

and restrain your child securely and conveniently so that you are able to install it correctly each time it is used.

3. Be certain that it is appropriate for the child's

height, weight, and development. The instructions and/or the regulation label attached to the restraint typically provides this information.

3-3

SECTION 3 –

Tether

Anchor

Loops

-Typical View

NOTE: Your coach may have one or two

tether anchor loops depending on model.

3. Tether

Shoulder

Belt

Tether hooked to

anchor loop

DRIVING YOUR MOTORHOME

4. Review the instructions for installation and use of the restraint. Be sure that you understand them fully and can install the restraint properly and safely in your vehicle.

Te ther Anchor Loop

-If Equipped

If your coach has a dinette, it may be equipped with a child seat tether anchor loop located beneath the forward facing dinette seat cushion.

1. Lower the dinette table.

NOTE: The dinette table must be in the lowered

position when a child seat is in use.

2. Set child seat upright on dinette seat.

3. Route the tether over the top of the dinette seat

back and hook it to the anchor loop (located beneath the forward facing dinette seat cushion). Pull tether strap to tighten.

3-4

4. Route the shoulder belt through the child seat. Fasten the shoulder belt and pull snug. The locking tab automatically holds the belt in place.

SECTION 3 –

Slide locking

tab to

release

tension on

the shoulder

belt

DRIVING YOUR MOTORHOME

Further Information

Refer to the chassis manual provided in your InfoCase for complete operating instructions on using the Remote Keyless Entry system and for battery replacement information.

HAZARD WARNING FLASHERS

The hazard warning flashers provide additional safety when the vehicle must be stopped on the side of the roadway and presents a possible hazard to other motorists. When the flashers are on, it serves as a warning to other drivers.

5. To remove the child seat, press the “red”

Further Information

instructions for proper attachment and adjustment of the tether and seat belts.

KEYS

keys. In addition to the chassis manufacturer’s ignition key, you receive keys for the entrance door and exterior compartment doors.

small metal tag or stamped into the key head. These numbers are recorded on the vehicle’s component model/serial sheet, which is included in your InfoCase. In case keys are lost or stolen, your dealer or a locksmith can provide you with duplicate keys or modify the locks.

REMOTE KEYLESS ENTRY

with a chassis-supplied Remote Keyless Entry system, which you can lock and unlock these doors using the provided keyless remote transmitter.

release button on the buckle and slide the tongue out of buckle.

See the child seat manufacturer’s specific

Your motorhome is supplied with several

Keys have an identification number, either a

The cab doors on your vehicle are featured

Further Information

See your chassis manual for instructions on activating, operating, and canceling hazard warning flashers.

AIR CONDITIONER/HEATER – AUTOMOTIVE (DASH)

See your chassis manual for operating information on driver and passenger comfort controls – air conditioner, heater, defroster, and ventilation.

NOTE: The dash air conditioner is not designed

to cool the entire interior of the coach, but is intended only to provide cooling for the cab area.

REARVIEW MIRROR WITH MONITOR SYSTEM

–If Equipped

Your coach may be equipped with a Rearview Monitor System built into the rearview mirror, which lets you see what is directly behind your vehicle for maneuvering assistance and safety.

Further Information

See the Rearview Mirror Monitor manufacturer’s user guide provided in your InfoCase for complete features and operating instructions.

3-5

SECTION 3 –

Battery Boost Switch

(Located on dash)

• Press and Hold in the ON position while turning ignition key for emergency starting power.

WARNING

DRIVING YOUR MOTORHOME

RADIO – IN-DASH

The radio in your coach is chassis-supplied. See your chassis manual for complete features, programming, and operating instructions.

BATTERY BOOST SWITCH

The Battery Boost switch can be used to draw emergency starting power from the house batteries to start the engine if the chassis battery is discharged.

Press and Hold the Battery Boost switch in the ON position while turning ignition key for emergency starting power.

NOTE: The House/Coach Battery Disconnect

switch near the entrance door must be ON and house batteries must be sufficiently charged for this feature to work.

freeze available at retail outlets. The coolant system MUST be refilled or topped up with the same type of coolant as equipped to maintain the special longlife properties.

Further Information

Refer to the chassis manual in your InfoCase for information and precautions on filling, servicing, and checking the fluid level.

LIGHTS

All exterior lights should be checked for proper operation each time the vehicle is prepared for a trip. Any bulbs which fail to light should be checked and replaced, when necessary, with a new bulb of the same size. A failure of more than one light, such as both taillights not operating, may indicate a burned out fuse. Check fuse and replace with one of the same rating when necessary. If a fuse is not the cause of the problem, the wiring system should be checked immediately by an authorized service center.

ENGINE COOLING SYSTEM

Do not remove the radiator cap while engine and radiator are still hot. Always check coolant level visually at the see-through coolant reservoir.

NOTE: Your chassis engine cooling system is

filled with special extended-life coolant that is not the same as common anti-

3-6

Further Information

Refer to the chassis manual in your InfoCase

for further information.

TIRES

Improper tire pressure can result in tire overloading and abnormal wear and also affects handling, ride characteristics, and fuel economy.

Make sure all replacement tires are of the same size and rating as those shown on your Vehicle Certification Label.

SUSPENSION ALIGNMENT AND TIRE BALANCE

The front suspension and steering system of this vehicle was factory aligned using highly accurate equipment prior to delivery to the

dealership. However, alignment should be checked and adjusted after you have fully loaded the motorhome according to your personal needs. Thereafter, the alignment should be periodically inspected to help prevent uneven tire wear.

Any excessive or abnormal tire wear may indicate worn or misaligned suspension or steering, unbalanced tire, or other tire/suspension problem.

Alignment can be affected by worn steering/ suspension parts or by incidents which happen during driving, such as hitting a curb, pothole, or railroad track, etc. Improper alignment can cause tires to roll at an angle and wear unevenly. It may also cause the vehicle to “pull” to the right or left. Have your dealer inspect your vehicle’s suspension and steering components periodically for misalignment or wear.

Out-of-balance tires will not roll smoothly and can lead to vibrations and uneven tread wear, such as cupping and flat spots. Tires may need to be balanced if uneven wear is detected or if ride comfort decreases noticeably.

SECTION 3 –

DRIVING YOUR MOTORHOME

Further Information

See the chassis manual in your InfoCase for further information.

3-7

SECTION 4 – APPLIANCES AND SYSTEMS

Place bubble level in bottom of refrigerator

Bubble must be at least 1/2 inside circle

The appliances installed in your motorhome are manufactured by reputable RV appliance makers and have been tested by independent laboratories to meet all applicable standards and codes set for RV appliances.

See Section 2 - Safety and Precautions of this manual for any safety and precautions you need to take regarding the operation of your appliances.

REFRIGERATOR

The refrigerator in your coach can operate from either of two energy sources available to the motorhome:

• 120-Volt AC Electric

• Propane Gas

To be able to use both types of energy, the refrigerator does not have a compressor like household refrigerators. Instead, it uses an ammonia-water solution for cooling. Basically, ammonia vapor is distilled from the solution by heat produced from either propane gas flame or electrical heat element. The ammonia vapor is then carried to the finned condenser where it liquefies. The liquid then flows to an evaporator where it creates cooling by evaporation. The ammonia circulates back into the water solution and the cooling cycle continues.

Leveling

Before operating the refrigerator when the motorhome is stationary, place a small level on the bottom of the refrigerator and make certain the unit is level. If over 1/2 of the bubble is inside the circle in any direction, the coach is level enough for continuous operation of the refrigerator while parked.

Normal vehicle leveling to provide comfort for the occupants is satisfactory for refrigerator operation.

NOTICE

To prevent permanent damage to the refrigerator cooling unit, turn the refrigerator off if the vehicle will be p arked on an incline of over 3 side-to-side or 6 front-to-rear (such as steep driveways or parking lots, etc.) for more than one hour.

Basic Operation

• Press the ON/OFF button to start the

refrigerator.

5 - DASH / AUTO

• If the display code reads “no” there is no

electricity or gas available to operate the refrigerator. Open the propane tank valve or connect the shoreline.

4-1

SECTION 4 –

-Typical View

Refrigerator Access Door Latches

•CLOSED

• OPEN

Refrigerator Access Compartment

-Typical View

APPLIANCES AND SYSTEMS

• Press the MODE button to select energy

source. There are three settings: LP (Gas Mode) - Refrigerator will operate on gas from the propane tank if the main valve is open and the tank contains gas. AC (Electric Mode) - Refrigerator will operate on 120-VAC household current if the shoreline is connected or the auxiliary generator is running. AU (Automatic Mode) - Refrigerator will automatically start operating on 120-VAC household current if the shoreline is connected or the auxiliary generator is running. If electricity is lost, it will automatically switch over to LP gas operation if gas is available.

• Press the TEMP SET button to change

temperature setting from 1 to 9 on display. Start at the ‘coldest’ setting to ensure coldest temperature in the freezer compartment, then adjust warmer as necessary after cold food has been added.

NOTE: The refrigerator will retain temperature

more efficiently if food is already cold before placing inside.

REFRIGERATOR SERVICE ACCESS COMPARTMENT

(Exterior)

The exterior refrigerator service compartment allows access to the rear of the refrigerator for inspection, maintenance, and service.

To Open

1. Use a screwdriver or coin to turn the latch

knobs to the vertical position as shown.

2. Remove the door from the opening.

To Close

1. Replace the door into the opening.

2. Push the latch knobs in while turning to the

horizontal position as shown.

Further Information

For further information and operating cautions, see the refrigerator operating instructions included in your InfoCase.

4-2

RANGE TOP

DA NG E R

-Typical View

To Light Range Top Burners

• Push in desired control knob and turn to IGNITE position - and maintaining the knob pushed in, press down on the spark pump a few times to light burners.

WARNING

The range in your motorhome operates on propane gas and will provide most of the functions of the range in your home.

Avoiding Asphyxiation

The following warning label has been located in the cooking area to remind you to provide an adequate supply of fresh air for combustion.

SECTION 4 –

APPLIANCES AND SYSTEMS

Unlike homes, the amount of oxygen supply is limited due to the size of the recreational vehicle, and proper ventilation when using the cooking appliances avoids dangers of asphyxiation.

It is especially important that cooking appliances not be used for comfort heating, as the danger of asphyxiation is greater when the appliance is used for long periods of time.

FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY.

Do not use gas cooking appliances for comfort heating. May lead to carbon monoxide poisoning, which can lead to death or serious injury.

Portable fuel-burning equipment including wood and charcoal grills and stoves, shall not be used inside the recreational vehicle. The use of this equipment inside the recreational vehicle can cause fires or asphyxiation. Failure to comply could result in death or serious injury.

NOTICE

Turn off the range and allow it to cool before closing the range cover . The range cover is made of glass and may shatter when heated.

4-3

SECTION 4 –

Gen Hourmeter

T ypical - Your coach may or may not be equipped with all of the features shown.

Gen Start

Gen Stop

Tank Levels Switch

APPLIANCES AND SYSTEMS Further Information

Refer to the appliance manufacturer’s operation manual provided in your InfoCase for complete features and operating instructions, as well as safety precautions and maintenance information.

MICROWAVE OVEN

-If Equipped

Refer to the manufacturer’s user guide located inside the appliance for complete operating instructions.

ONEPLACE® SYSTEMS MONITOR PANEL

The OnePlace Systems Monitor Panel provides a convenient, central location for checking the condition of all utility systems in your coach.

At the touch of a button, the monitor panel will display the fresh water and holding tank levels, propane gas tank level, plus the chassis battery and house battery condition. You can start the generator and check the generator hourmeter or turn on the water pump and water heater.

Water And Holding Tank Levels

Press the Tank Levels switch to show

approximate levels on the LCD screen.

Generator Start/Stop Switches and Hourmeter

See Section 6 - Electrical for generator startup/shut-down and generator hourmeter instructions.

The approximate fluid levels are measured by electronic sensors on the sides of the tanks. Tank levels are displayed as 1/3, 2/3, and Full (F). There is generally more fluid in a tank than indicated on the monitor panel.

4-4

Tank Capacities

Water Tank

-Typical View

Sensors

Battery Levels Switch

LP Gas

Water Heater Switch

Water Pump Switch

See “Tank Capacities” in Section 1 -

Introduction.

SECTION 4 –

APPLIANCES AND SYSTEMS

• An interior light should be turned on to provide a small load which draws off the battery surface charge.

Water Heater Switch

See Water Heater information elsewhere in

this section for operating instructions.

Propane Gas Level

Press the Tank Levels switch to show

approximate propane tank level.

The propane level is registered by a sending unit on the tank. The gauge mounted on the side of the tank will give a more accurate indication of actual tank level if needed.

Battery Charge Meter

Press the Battery Levels switch to check the level of charge (voltage) in the chassis and house batteries.

Water Pump Switch

When use of the self-contained water system is desired, press the Pump switch (press once to get to the desired screen, and a second time to activate or deactivate.) Water will be available as soon as a faucet is opened.

To get an accurate reading:

• Both the chassis engine and the generator engine must be shut off and 120-volt AC shoreline unplugged.

Refer to Section 7 - Plumbing for additional information on the water pump and initial startup.

4-5

SECTION 4 –

Water Heater Power Switch

(Push up to turn ON)

Propane Gas Water Heater Switch

(Located on OnePlace

monitor panel)

Gas Modulating Dial

• Turn “clockwise” to increase hot water temperature.

• Turn “counter-clockwise” to decrease the temperature.

APPLIANCES AND SYSTEMS

NOTE: Some models may be equipped with a

Water Pump switch in the water service center on the outside of the coach or within the bathroom area for your convenience.

WATER HEATER - GAS TANKLESS

-If Equipped

The Gas Water Heater operates from propane

gas.

See the Water Heater manufacturer’s operation manual provided in your InfoCase for complete operating instructions, safety warnings, and maintenance information before operating the Water Heater.

1. Turn the Water Heater Power switch (located

inside the water heater door) to the ON position.

3. Set the Gas Modulating Dial to the appropriate setting.

2. Press the W ater Heater LP switch to ON. The monitor panel display will indicate that the heater is “On”. If the monitor panel display reads “W ater Heat LP Fail”, it means th at the burner has gone into “lockout” mode and must be restarted. If this happens, turn the Water Heater LP switch off for about 5 minutes, then turn it back on.

4-6

• Normal Weather - Set dial to the middle area.

• Extreme Cold Weather - set the dial to the extreme right area (large flame).

• Extreme Hot Weather - set the dial to the extreme left area (small flame).

4. Open a hot water faucet anywhere in the coach to a normal flow rate. Wait for the water to travel from the Water Heater to the faucet. (this may take a few seconds to a minute). If the Hot water is not Hot enough, turn the Gas Modulating Dial “clockwise” to increase the flame/BTUs to raise the Hot Water Temperature.

Note: Use caution not to increase the Dial too

Water Heater Exterior Service Access

-Typical View

CAUTION

• Lift handle straight out to open P-T valve when water heater is cold.

-Typical View

much which could cause the Hot Water Temperature to rise to the point the Water Heater “limits” and turns OFF the flame. Flame shut off is approximately131 degrees F.

Further Information

See the Water Heater manufacturer’s operation manual provided in your InfoCase for complete operating instructions, safety warnings, and maintenance information.

PRESSURE-TEMPERATURE RELIEF VALVE (TANKLESS WATER HEATER)

On occasion, water may be seen seeping from the water heater pressure temperature relief valve. This is no cause for repair or replacement of the valve.

SECTION 4 –

APPLIANCES AND SYSTEMS

Hot water can escape from tank causing injury. Operate this valve only when the tank water is cold.

To Replace the Air Gap:

1. Turn off the Water Heater switch and incoming water supply (city water and/or demand pump).

2. Open a faucet in the motorhome to relieve water pressure.

3. Pull the handle of the P-T valve straight out and allow water to flow until it stops.

Normally there is an air gap at the top of the heat exchanger, which acts as a pressure buffer. In time, however, heated water may expand and fill this air gap, causing a slight increase in water pressure. This may cause the P-T valve to “weep” until the air gap is manually replaced.

4. Let the handle of the P-T valve snap shut.

5. Close the faucet and turn on the water supply before switching the water heater on.

Manually operate the pressure temperature

relief valve at least once a year.

PROPANE GAS FURNACE

To Start Up

1. Open the Propane Gas T ank valve by turning fully counter-clockwise.

2. Move the Thermostat/Switch from OFF to the desired temperature position.

4-7

SECTION 4 –

Thermostat/Switch

• Move from OFF to desired temperature for furnace operation

Room Temperature

Thermometer

APPLIANCES AND SYSTEMS

nuisance smoke alarm. We do not recommend removing the smoke alarm battery.

To Shut Down

• Move Thermostat switch to OFF position.

• Close Propane Gas T ank valve if coach will be stored for a period of time.

Further Information

Refer to the manufacturer’s user guide provided in your InfoCase for further information, including operating precautions and periodic maintenance. See the Coach Maintenance Schedule for recommended intervals.

3. Furnace fan should start to blow immediately after setting the Thermostat.

4. After approximately 30 seconds, the Furnace burner should light.

5. The Furnace should now cycle off and on automatically as the Thermostat demands just like a household furnace.

If heat does not come out of the heat ducts

after a minute or so, the burner is not lit.

Turn Thermostat OFF for 3-5 minutes, ensure Propane Gas Tank valve is open and tank is not empty, and repeat Steps 2 through 4.

If the Furnace will not light after three attempts, follow “Shut Down” steps and contact your dealer or a local RV service center for repair.

NOTE: If the Furnace burner has any residuals

of metal protectant or lubricants used during manufacture of the Furnace, it may smoke slightly when the Furnace is used for the first time and may set off your smoke alarm. We recommend that you provide adequate ventilation when using the Furnace for the first time to avoid a

ROOF AIR CONDITIONING WITH HEAT STRIP

–If Equipped

Your coach may be equipped with an air source heat strip built into the air conditioning system. Because the heat strip operates on electricity, it provides economical heat inside your coach and helps reduce the use of propane gas for heating in cooler weather.

To operate the heat strip

• Turn the selector switch to the “High Heat”

position, which allows the fan to operate at high speed with maximum heat output.

• Rotate the temperature control switch to the

position that is the most comfortable to you. When the temperature of the air entering the air conditioning unit drops below this setting a few degrees, the thermostat will turn the internal heat strip on. It will automatically

4-8

SECTION 4 –

APPLIANCES AND SYSTEMS

turn off when the temperature of the air entering the air conditioner rises a few degrees above this setting. The internal heat strip will continue to cycle on and off until the selector switch is turned to another operation mode.

Check your Air Filter

Closed or blocked vents and a dirty air filter

can hinder the efficiency of a heat strip.

• Be sure ceiling vents are open to distribute heat strip output air.

• The A/C return air filter should be checked monthly for dirt build-up and cleaned or replaced as needed. See “Air Conditioner Filter” elsewhere in this section.

the setting you have selected, the thermostat will turn the compressor on. When the temperature of the air entering the air conditioning unit drops below the selected setting, the thermostat will turn the compressor off. When the air conditioner is in the cooling mode, it will continue to cycle the compressor on and off until the selector switch is turned to another operation mode.

• Position the louvers to the desired direction the discharge air is to flow.

During Cooler Nights

When outdoor temperatures drop in the evening or at night below 75 degrees F, the temperature control needs to be set at midpoint between “Warmer” and “Cooler”. If the setting is at “Cooler”, the evaporator coil may become iced up and stop cooling. During the day when temperatures have risen to at least 75 degrees F, reset the thermostat switch to the desired setting.

NOTE: Should icing up occur, it is necessary to

let the evaporator coil defrost before normal cooling operation is resumed. At this time, operate the air conditioning unit in the “High Fan” position with the system at maximum airflow. When increased or full airflow is observed, the evaporator coil should be clear of ice.

Further Information

See the air conditioning/heat strip manufacturer’s information in your InfoCase for complete operating instructions.

ROOF AIR CONDITIONING SYSTEM

Cooling Operation

• Turn the selector switch to the “Low Cool” or

“High Cool” position.

• Rotate the temperature control to the position

that is the most comfortable to you. When the temperature of the air entering the air conditioning unit rises a few degrees above

Further Information

Refer to the air conditioner manufacturer’s information in your InfoCase for complete operating instructions.

AIR CONDITIONER FILTER

The washable foam air conditioner filter is located in the ceiling-mounted return A/C grille in the lounge area of the coach.

It is recommended to check the filter monthly for dirt build-up and cleaned or replaced, as necessary.

4-9

SECTION 5 – PROPANE GAS

WARNING

Propane Tank Features

(Located on driver side of coach)

Remove cover to access.

-Typical View

Relief Valve

Tank Fill

Valve

Overflow Valve

Tank Gauge

and Sender

Tank Supply

(Main) Valve

PROPANE GAS SUPPLY

The propane gas system supplies fuel for the gas range/oven, water heater, furnace, and refrigerator (while in gas mode). When used and handled properly, this system is safe and economical and provides modern living conveniences wherever you travel.

See Section 2 of this manual for other safety and precautions you need to be aware of related to propane.

How Propane Gas Works

Propane is a type of LP (Liquefied Petroleum) gas compressed into liquid form for easy transportation and storage. Propane gas may also be called tank gas, bottle gas, or simply LP.

Propane is used by appliances in vapor form only, but is stored in the tank as a liquid under very high pressure. As the liquid gas is released, it reverts back to a vapor and expands to many times its compressed volume.

Propane Tank System

The storage reservoir for the propane gas system is a horizontally mounted tank which is permanently attached to the vehicle frame. The tank is accessible only from the outside of the vehicle.

Do not alter or remove propane tank valves or gauge. Propane can escape, which can cause an explosion resulting in death or serious injury . Have the propane system serviced by a qualified service center.

Refilling Propane Tank

Since the propane tank is permanently mounted to the frame, the coach must be taken to a propane dealership for filling. Do not attempt to remove the propane tank from the vehicle. The tank is equipped with a fill adapter with both internal and external threads, which allows easy filling with any propane filling equipment. The tank is full when liquid propane gas appears at the overflow valve.

NOTE: The propane tank is equipped with an

automatic 80% stop-fill device.

5-1

5 - DASH / AUTO

SECTION 5 –

WARNING

DA NG E R

WARNING

PROPANE GAS

Do not fill propane container(s) to more than 80 percent of capacity. A properly filled container contains approximately 80 percent of its volume as liquid propane. Overfilling the propane container(s) can result in uncontrolled propane flow , which could lead to a fire or explosion and result in death or serious injury.

All pilot lights, appliances, and their igniters (see operating instructions) shall be turned off before refueling of motor fuel tanks and/or propane containers. May cause ignition of flammable vapors, which can lead to a fire or explosion and result in death or serious injury.

Selecting Propane Fuel Types

We recommend using straight propane in your propane tank. Propane gas is commonly available at all propane gas outlets in the U.S. (According to the National Propane Gas Association, propane gas outlets in the United States do not offer any other type of liquefied petroleum gas than propane to the general public.) Check local phone directory yellow pages for locations of local propane gas refilling stations or bulk dealerships.

NOTE: If you travel outside the U.S. with your

motorhome, you may find butane or propane/butane mixtures available in addition to propane. Because gasburning RV appliances ar e designed to run on propane only, we recommend that you request straight propane only. Butane burns about 30 percent hotter than propane and can overheat some appliances, particularly refrigerators, and cause permanent damage. Other appliances designed to operate on propane can become sooted and lose efficiency by using butane fuel.

This propane piping system is designed for use with propane only. Do not connect natural gas to this system. Securely cap inlet when not connected for use. After turning on propane, except after normal cylinder replacement, test propane piping and connections to appliances for leakage with soapy water or bubble solution. Do not use products that contain ammonia or chlorine to test for leaks. May lead to a fire or explosion, which could result in death or serious injury.

Air in the Propane Gas Tank

If your gas appliances do not stay lit or require frequent adjustment, even though you know the propane tank contains sufficient fuel, the problem may be air in the propane gas tank. Air in the tank mixes with the propane gas vapors causing them to burn poorly. This condition could linger for weeks if the air is not purged from the tank. Most propane gas dealers have equipment for purging air from propane gas tanks and will purge before refilling the tank.

SAFE USE OF THE PROPANE GAS SYSTEM

The propane system is designed and built with strict adherence to national, state, and recreational vehicle industry requirements for mobile propane gas equipment.

5-2

SECTION 5 –

DA NG E R

PROPANE GAS

For your safety, there are many safety devices and backup systems installed, such as tank fill overflow valves, an interior propane gas detector/ alarm, and an interior carbon monoxide (CO) detector/alarm.

Propane gas also contains an odor additive that you can smell if propane is present in the air.

Here are a few precautions to observe that will help you to use the propane gas system safely:

• Exercise caution at all times. Be familiar with

the distinctive odor of propane gas. If a leak is suspected, turn off the supply valve immediately. Have the propane gas system checked by your dealer or other qualified propane gas service center.

• Do not tamper with the propane gas piping

system, pressure regulator, or gas appliances. Service and maintenance of propane gas system components should be performed only by your dealer or a qualified propane gas service center.

• Never attempt to connect natural gas to the

propane gas system.

• Have the entire propane gas system inspected

for possible leaks and missing or damaged parts at each tank filling. Also inspect before and after each trip, and any time trouble is suspected.

• Turn the propane supply valve off when not

using the propane gas system.

• Never use a wrench to tighten the tank supply

valve. It is designed to close leak-tight by hand. If a wrench is required to completely close the valve, it is defective and must be replaced.

• Be sure appliance and outside vents are open

and free from obstruction when using the propane gas system.

• Exercise caution when drilling holes or attaching objects to the walls. Gas lines and electrical wiring could be seriously damaged and present an extreme safety hazard.

PROPANE GAS WARNINGS AND PRECAUTIONS

It is illegal for vehicles equipped with propane tanks to travel on certain roadways or through certain tunnels in the U.S. To avoid inconvenience, check state regulations concerning flammable gas transportation.

Propane Gas Leaks

The following label is located in the vehicle near the range area. If you smell gas within the vehicle, quickly and carefully perform the procedures listed.

IF YOU SMELL PROPANE

1. Extinguish any open flames and all smoking materials.

2. Shut off the propane supply at the container valve(s) or propane supply connection.

3. Do not touch electrical switches.

4. Open doors and other ventilating openings.

5. Leave the area until odor clears.

6. Have the propane system checked and leakage source corrected before using again.

Ignition of flammable vapors could lead to a fire or explosion and result in death or serious injury.

• Never attach a lock or any device requiring a key to the propane tank compartment door. According to standards set for recreation vehicles, the propane supply valve must be readily accessible in an emergency.

• All pilot lights must be extinguished and appliances and their ignitors turned off while refilling the fuel tank or propane tank.

• Never smoke while refilling vehicle fuel tank or propane gas tank.

5-3

SECTION 5 –

WARNING

-Typical installation shown

PROPANE GAS

• Avoid inhaling exhaust gases produced by burned gasoline, diesel fuel, or propane gas in items such as the range, chassis engine, generator engine, refrigerator, furnace, and water heater . They contain carbon monoxide, which is an odorless, colorless, and poisonous gas.

Propane cylinders shall not be placed or stored inside the vehicle. Propane cylinders are equipped with safety devices that relieve pressure by discharging propane to the atmosphere. Failure to comply could result in death or serious injury.

• Never use an open flame to test for propane gas leaks. Replace all protective covers and caps on propane system after filling. Make sure valve is closed and door latched securely .

the cover is kept in place to minimize vent blockage that could result in excessive propane pressure causing fire or explosion.

Only your dealer or a qualified propane gas service should remove the regulator cover for adjustments.

Visually inspect the pressure regulator vent periodically for blockage by accumulated debris or insect nests, etc. Vent obstruct ion could result in excessive pressure causing fire or explosion, which could result in death or serious injury . If an obstruction exists, have the regulator serviced by a qualified service center.

• Portable fuel-burning equipment, including wood and charcoal grills and stoves, shall not be used inside the recreational vehicle. The use of this equipment inside the recreational vehicle may cause fires or asphyxiation.

• Regulators are equipped with a protective cover . Make sure that the regulator vent faces downward and that the cover is kept in place to minimize vent blockage, which could result in excessive gas pressure causing fire or explosion.

PROPANE GAS PRESSURE REGULATOR

The pressure regulator is protected from the elements by a plastic cover, which should be left in place at all times.

Propane regulators must always be installed with the regulator vents facing downward. Regulators that are not in compartments have been equipped with a protective cover. Make sure that the regulator vent faces downward and that

5-4

Regulator Freeze-up

Regulator freeze-ups are caused by the presence of moisture in fuel. This moisture will pass through the cylinder valve and into the regulator where it can freeze. Fuel producers, tank and bottle manufacturers, and propane gas dealers take every precaution to reduce moisture, but sometimes only a fraction of an ounce entering the tank can cause problems. To help avoid the possibility of freeze-up, always keep tank control valve closed when not in use, even when tank is empty, to prevent moisture from collecting on the inside.

If regulator freeze-up should occur, you may attempt to thaw the regulator using a light bulb.

DO NOT USE AN OPEN FLAME OR HEAT LAMP.

If moisture begins to cause problems, have your propane gas dealer inject a small amount of dry methyl alcohol in your tank (approximately one ounce to 20 pounds or one pint to 100 gallons) to help guard against regulator freezeups.

SECTION 5 –

PROPANE GAS

This means that in extremely cold weather when a large volume of gas is being used by the furnace for heating, it is possible to experience a loss of gas pressure.

At first, this problem may appear to be caused by an empty tank or a regulator freeze-up, but is actually caused by failure of the liquid gas to vaporize as fast as it is needed by the furnace.

The demand for propane to produce heat increases to the point where the gas cannot vaporize fast enough to keep the furnace going. The only solution to this problem is to reduce gas usage where possible.

Adjusting the temperature on the gas/electric refrigerator may be a first step. Using less hot water will also help, as well as refraining from using the gas cooktop. A final step is to lower the thermostat setting to reduce gas usage by the furnace.

PROPANE VAPORIZATION IN COLD WEATHER

Propane gas vaporization increases and decreases in direct relation to ambient temperature. In other words, the lower the temperature, the slower the liquid propane will vaporize into a usable gas for appliances.

5-5

SECTION 6 – ELECTRICAL

WARNING

Your coach is equipped with an electrical system consisting of two separate voltages:

• 12-volt DC system (battery current); and

• 120-volt AC system (household current)

The 12-volt system consists of two internal power sources, while the 120-volt system is operated from an outside power source or the optional 120-volt generator.

ELECTRICAL CAUTIONS

• Careless handling of electrical components

can be fatal. Never touch or use electrical components or appliances while feet are bare, while hands are wet, or while standing in water or on wet ground.

• Improper grounding of the vehicle can cause

personal injury . Do not plug the utility power cord into an outlet which is not grounded and do not adapt the plug to connect to a receptacle for which it is not designed.

• Do not attach an extension cord to the utility

power cord.

• Be sure that all electrical appliances to be used

contain 3-prong plugs for proper grounding.

the power converter automatically changes a portion of the 120-volt current to 12-volt DC current. All equipment in the motorhome that is normally powered by the house batteries is then powered through the converter.

In addition, the following equipment is entirely dependent on 120-volt current: air conditioner, refrigerator (when placed in AC mode), microwave oven, and any 120-volt electrical equipment used at convenience outlets.

POWER CORD – EXTERNAL

(Shoreline)

Do not use an extension cord. Improper sized cords, damaged cords, and poor connections can lead to fire, which can result in death or serious injury.

• A void overloading electrical circuits. Replace fuses or circuit breakers with those of the same size and amperage rating only. Never use a higher rated fuse or breaker.

• Use caution when handling or working near electrical storage batteries. Always remove jewelry and wear protective clothing and eye covering. Avoid creating sparks.

ELECTRICAL SYSTEM – HOUSE 120-VOLT AC

The 120-volt system operates from the shoreline cord connected to an outside 120-volt utility service, such as those at campgrounds or from the 120-volt generator. When the shoreline cord is connected to an outside power source, or when the auxiliary electric generator is running,

Do not connect the external power cord to any receptacle until you have verified proper polarity and grounding. Be sure all prongs of the supply cord are properly plugged into the receptacle. Failure to observe can result in death or serious injury.

The external power cord (commonly referred to as a “shoreline”) is located in a driver side compartment.

To connect to an external power source, remove the power cord from the utility compartment and plug it into a suitable power outlet box.

5 - DASH / AUTO

6-1

SECTION 6 –

WARNING

30 Amp Receptacle

WARNING

• Swivel the small cover section upward to access the cord passage.

• Route power cord through passage and close door while shoreline is connected to outlet.

ELECTRICAL

This connection is for 110/125 Volt AC, 60 Hz 30 Ampere supply. Do not exceed circuit rating. Exceeding the circuit rating may cause a fire and result in death or serious injury.

The power cord is designed to ground the electrical system through the receptacle. It is also designed to carry the amperage output of most campground outlets. If the electrical receptacle to be used is designed to mate with the prongs of the power cord plug, the electrical connection can be expected to carry rated load.

Power Cord Door

(Models with power cord compartment on sidewall)

–If Equipped

A flip-up passage in the power cord door lets you route the power cord out of the compartment and close the door while the power cord is connected.

After disconnecting the power cord, neatly

replace it in the cord compartment.

Service inlet access must be closed when utility connections are not in use.

6-2

Park Fuses or Breakers

Most campgrounds are equipped with a fuse or circuit breaker at the receptacle (which we recommend shutting off before engaging or disengaging the power cord.) This protects the park’s wiring, as well as the power cord on your

vehicle from electrical damage. If electrical

12-Volt

House Fuses

120-Volt

Circuit Breakers

Power Center (Converter)

-Typical View

power fails, contact the park attendants and have them check the fuse or breaker for your supply receptacle.

POWER CENTER

(Converter)

The power converter is generally located in a lower cabinet face in the galley or living area, depending on the floorplan of your model.

The converter power panel contains the house electrical system 120-volt circuit breakers and 12-volt fuses.

The power converter changes 120-volt AC current from the auxiliary generator or the shoreline into 12-volt DC current for use by 12volt equipment in the motorhome.

SECTION 6 –

ELECTRICAL

NOTICE

Do not block the converter cover vents in any way. The converter generates heat while operating and needs unrestricted airflow for proper cooling. Damage to the converter can result.

Further Information

See the manufacturer’s operation, care, and maintenance information provided in your InfoCase.

Charging Section

The converter charges house batteries while 120-volt external power is connected. The converter will automatically “sense” the condition of the battery. If it is below “full charge”, the Charging Section will start charging the batteries.

If the house batteries have been extremely discharged, they will accept charge at a relatively high amperage rate. If they are only slightly discharged, they will charge at a lower amperage rate. The rate of charge will decrease as the batteries reach “full charge”, then will continue “trickle” charging at a very low amperage rate. If your battery does not charge as described above, it is possible the battery is defective.

Certain circuits, however, remain unchanged

for use by items which require 120-volt current, such as the air conditioner(s), the refrigerator in AC mode, the microwave oven, etc.

NOTE: The converter will not change 12-volt

DC current to 120-volt AC.

Current drawn from the house batteries passes through the power converter unchanged, although it is routed through a series of protective fuses located on the power panel.

Thermal Overload

A thermal overload will “break” the 120-volt AC power to the converter section of the Power Center if the power converter becomes overheated. This can result from operating above its maximum limit for an extended period of time or by obstruction of ventilation to unit.

NOTE: The power converter section will

automatically route 12-volt lights and motors to house battery power in this event.

The thermal overload will reset itself after a period of time, and the lights and motors will again resume operation from the power converter section. If the breaker trips again shortly after

6-3

SECTION 6 –

120-Volt Circuit Breakers

-Typical View

• Push to Reset circuit after monthly testing or ground fault tripping.

• Push to Test at least monthly. Should break circuit. Press Reset button to reconnect.

GFCI Outlet

(Ground Fault Protector)

ELECTRICAL

reset, take immediate steps to correct the cause of overheating. A portion of the house 12-volt load (lights or motors or both) should be turned off to reduce total load. Also, inspect the power converter to make sure ventilation is not obstructed.

CIRCUIT BREAKERS – HOUSE 120-VOLT AC

The breaker panel protects all 120-volt components in the motorhome from either an overload on the circuit or a short in the wiring or component itself. When an overload or short develops, the breaker will open preventing damage to the system.

Shut off the equipment (example: roof air conditioner) and allow a brief cooling period. Then reset the breaker by moving the switch to “Off” and back to “On”. If the breaker is continually tripped and no overload is evident, have the system checked for a short in the wiring or the appliances.

ELECTRICAL OUTLETS – HOUSE 120-VOLT AC

A number of standard household electrical outlets are provided throughout the coach for connecting small appliances such as televisions, radios, toasters, etc.

An exterior outlet is also located on the outside of the coach near the entrance door or in a storage compartment on the passenger side of the coach.

GROUND FAULT CIRCUIT INTERRUPTER

Bath, galley, and exterior outlets are connected to a GFCI (Ground Fault Circuit Interrupter), which is an extremely sensitive circuit breaker that will help to protect against severe electrical shock if a ground fault develops. If such a condition occurs, the GFCI will break the circuit by turning off the power to the protected outlets. Should this occur, unplug all the appliances on that circuit and press the reset button on the GFCI equipped outlet.

If the GFCI keeps tripping, have the electrical system checked and repaired, if necessary, before using again.

NOTE: Typical view of breaker panel. Breaker

arrangement may vary according to appliance and equipment options. Fuses and breakers are labeled on panel.

6-4

SECTION 6 –

WARNING

Power CordGenerator

Receptacle

WARNING

Generator Start/Stop Buttons

(Located on monitor panel)

-Typical View

ELECTRICAL

The GFCI will not completely eliminate the risk of electrical shock. Infants and small children may still be affected.

ELECTRICAL GENERATOR – 120-V OLT

–If Equipped

Careless handling of the generator and electrical components can be fatal. Never touch electrical leads or appliances when your hands are wet, or when standing in water or on wet ground. Do not attempt to repair the generator yourself. Service should be performed by a qualified service center.

To use the 120-volt Generator, plug the power cord into the Generator receptacle within the utility compartment before starting the Generator.

Do not plug the power cord into the generator receptacle while the generator is running. Electrical shock can cause personal injury.

Generator Basic Operation

NOTE: If the GenSet Start or Stop switch is

momentarily pressed, the monitor panel will automatically try to start or stop the Generator. It will try 4 times (10 second crank, 10 second rest).

To Start the Generator

Press and Hold the GenSet Start button until you hear the Generator running smoothly, then release.

To Stop the Generator

Press and Hold the GenSet Stop button until you hear the Generator come to a full stop, then release.

Generator Hourmeter

The Generator hourmeter registers the total number of hours that the Generator has been operated. Press the GenSet Meter button once to get reading.

6-5

SECTION 6 –

WARNING

Generator Hourmeter Button

-Typical View

ELECTRICAL

Refer to the hourmeter to determine when periodic maintenance is due and to record services which have been performed.

Operation Warnings and Cautions

Check Generator oil level frequently during periods of use. Refer to the Generator manufacturer’s user guide provided in your InfoCase for specific recommendations.

Further Information

Refer to the Generator manufacturer’s user guide provided in your InfoCase for specific recommendations, operating instructions and cautions, troubleshooting, and maintenance.

ELECTRICAL SYSTEM – HOUSE 12-VOLT DC

The DC voltage system consists of the chassis battery, the 12-volt house batteries, and the 12volt power converter.

Converter

See “Power Center.”

The exhaust of all internal combustion engines contains carbon monoxide (CO). This poisonous gas is colorless, odorless, tasteless, and lighter than air. The exhaust systems of both your motorhome engine and your generator engine have been installed with your safety in mind. However, certain precautions must be taken when using them to protect yourself from conditions beyond the control of the manufacturer.

• Do not simultaneously operate the Generator and a power vent, which could draw exhaust gases into the vehicle.

• Do not open windows or vents on the end or side of the vehicle where exhaust pipe of the Generator is located.

• Park the vehicle so that the wind will carry the exhaust away from the vehicle. Also, note the position of other vehicles to be sure their exhaust will not enter your vehicle.

• Do not operate the Generator engine while parked if vegetation, snow, buildings, vehicles, or any other object can deflect the exhaust under or into the vehicle.

Chassis Battery

The chassis battery is used to operate the engine starter and automotive accessories and controls found on the instrument panel. The slideout room systems and the electric step are also connected to the chassis battery.

See your chassis manual for further information on chassis batteries and chassis electrical system.

House Batteries

House batteries are “deep-cycle” type batteries specially designed for recreational vehicle use. They will provide longer lasting power than standard automotive starting batteries and will withstand the frequent drain-andrecharge cycles that occur under the demanding conditions of a camping outing.

The house batteries supply power to 12-volt equipment located in the living area of the motorhome. This includes the following 12-volt powered components (if equipped): interior 12volt lighting, range exhaust fan, propane furnace fan, fresh water pump, systems monitor panel, refrigerator, roof vent fans, and 120-volt electrical generator starter.

6-6

The house batteries can also provide

House/Coach Battery Disconnect Switch

(Located on galley end)

-Typical View

House Battery Access

(Located under center of coach)

- Remove bolts from battery retainer to remove house battery

-Typical View

emergency power to start the engine if the chassis battery is discharged. (See “Battery Boost Switch” in Section 3 - Driving Your Motorhome).

House batteries are automatically charged by

the chassis alternator while the engine is running.

HOUSE/COACH BATTERY DISCONNECT SWITCH

SECTION 6 –

ELECTRICAL

BATTERY ACCESS

NOTICE

Always refasten battery retainers when returning a battery to the compartment.

(COACH BATT)

The House/Coach Battery Disconnect switch lets you disconnect the house batteries from the 12-volt system of your coach during storage periods to avoid battery drain by electrical items that are hooked directly to the house batteries, such as clock displays and radio memories, etc.

Always leave this switch ON while using the coach.

NOTE: Some electronic displays and memory

functions may need to be reset after power has been reconnected.

See also “Battery Care” elsewhere in this section.

House Battery

The house battery is accessible from outside of the vehicle beneath the passenger side of the coach. Remove bolts from battery retainer to remove the house battery.

NOTE: Your house battery (batteries) are

“Absorbed Glass Mat” type, or AGM. They are maintenance-free and do not require checking or adding battery fluid.

Chassis Battery

The chassis (starting) battery is located beneath the driver side floor mat.

6-7

SECTION 6 –

Chassis Battery Access

(Located beneath driver side floor mat)

-Typical View

WARNING

ELECTRICAL

The two best defenses against sulfating and insufficient charge are to:

1. Turn of f the House/Coach Battery Disconnect switch to avoid parasitic discharge (the trickle discharge caused by directly connected components like propane gas detectors or digital clock displays, etc.)

2. Check the battery and recharge as necessary at least once a month during long storage periods. Turn the House/Coach Battery Disconnect switch off to avoid electrical arcing when attaching or detaching charger clamps.

NOTICE

Further Information

See the chassis manual provided in your

InfoCase for details on access and servicing.

BATTERY CARE

Lead-acid type batteries are electro-chemical devices for storing and releasing electrical charge. As such, they are simply an electrical reservoir, not an electrical source. As soon as energy is removed from the battery, it should be replaced by the engine alternator or the coach converter system.

If a battery sits unused for 30 days or more, especially during warm weather, it can develop a deposit of sulfate crystals on the metal plates inside the battery. This condition is called “sulfating” and prevents the battery from either releasing or accepting a charge. If this condition occurs, the battery must be replaced.

If a battery does not contain at least 80% charge during freezing temperatures, the electrolyte can freeze and crack the battery case.

Disconnect batteries before connecting external charging equipment to avoid damage to sensitive electronic components.

This vehicle, like other vehicles, may contain small amounts of one or more substances which are listed by the state of California for causing cancer or reproductive toxicity.

California Proposition 65 Warning:

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Wash hands after handling.

6-8

NOTE: Do not leave the shoreline plugged in

WARNING

during storage. Follow regular battery inspection and maintenance.

Further precautions are:

• Check the state of charge periodically to avoid discharge or sulfating.

To ensure that the battery will always accept and hold a charge, follow these simple maintenance practices:

• Make sure the batteries always remain

securely clamped in the battery tray.

• Make sure battery cable clamps are tight on

the terminal posts and are free of corrosion.

• Neutralize corrosion buildup or acid film on

top of battery by washing with a baking soda/ water solution. Rinse with clear water.

NOTE: Make sure vent caps are on securely to

prevent baking soda solution from entering the battery and contaminating the electrolyte fluid.

SECTION 6 –

ELECTRICAL

To prevent wiring damage, it is essential when replacing the cables on the battery , or when using a “booster” battery , that the positive post and the positive cable be attached and the negative post and negative cable be attached. The posts are marked (+) plus and (-) minus. If a “boost charger” is used while battery is in the motorhome, disconnect both battery cables before connecting the charger to avoid damage to engine electronic components. Never attempt to charge or boost a frozen battery . An explosion can occur resulting in personal injury.

Chassis Battery

If your coach is going to be unoccupied for two weeks or more, Winnebago Industries® recommends disconnecting the chassis battery in your coach to avoid battery discharge.

Before removing any battery cables or battery, make sure all 12-volt equipment in the motorhome is off and the power cord has been disconnected. Be sure to replace the battery terminal boot, if supplied, back onto the positive terminal after servicing. Care must be taken to avoid pinching the cable between any metal parts. Should the cable be damaged, a short circuit could result in personal injury or damage to equipment. Replace any damaged cables at once. Always remove jewelry and wear protective clothing and eye covering when checking or handling batteries.

• Clean and tighten battery terminals and have the specific gravity checked at least once a year.

CIRCUIT BREAKERS AND FUSES – HOUSE 12-VOLT DC

All 12-volt circuits and equipment in the coach area of the motorhome are protected by either a fuse panel or breaker panel. When a circuit is overloaded or a short develops in any part of the system, a fuse or breaker will shut down that circuit. If this happens, turn off all affected lights or appliances and reset the breaker or replace the fuse with a new one of equal amperage rating.

House 12-Volt Fuses

A label on the panel states the amperage rating and circuit protected for each fuse.

The fuse panel is located on the right-hand side of the Power Converter.

6-9

SECTION 6 –

House 12-V olt Fuse s

(Located on right-hand

side of Power Converter)

-Typical View

Functional Non-Functional

ELECTRICAL

The fuse panel accepts only blade type plug-in fuses. Always replace fuses with those of the same amperage rating.

Battery Charge Meter

See related item under “Systems Monitor Panel” in Section 4 - Appliances.

Battery Boost Switch

See Section 3 - Driving Your Motorhome for information on the Battery Boost switch.

6-10

SECTION 7 – PLUMBING

WARNING

Water Tank Gravity Fill

-Typical View

FRESH WATER SYSTEM

The Fresh Water System provides water to the galley sink, shower, bathroom lavatory, toilet, and water heater. Water may be supplied by either of two sources:

• A fresh water tank and water pump located

within the motorhome, or

• Any external fresh water source to which the

motorhome may be connected, known as “city water”.

Water Pressure Regulators

Because city water pressure varies from location to location, we recommend obtaining an in-line water pressure regulator to prevent damage to any components, connections, and seals in your fresh water system.

These devices simply connect in-line between the supply hose and the city water input on the coach. We recommend regulators that control water pressure to 50 psi. max.

Water pressure regulators are commonly available at most RV dealerships and many large retail discount or home supply centers.

Filling the Fresh Water Tank Through Gravity Fill

Potable water only. Sanitize, flush, and drain water tank before using. See owner’s manual for instructions, care, and maintenance information. Failure to maintain tank may result in death or serious injury.

The gravity tank fill tube is located behind a

small, lockable door on the driver sidewall.

• Insert hose into fill opening and turn water supply on. T ank is full when water flows from the tank vent tube beneath coach and out of the Gravity Fill door.

Using Tank Water (Gravity Fill)

• Turn Water Pump switch ON. While the switch is on, the water pump will automatically supply tank water as needed.

WATER PUMP

When your coach is not connected to a city water supply, water is supplied from the fresh water tank by a water system demand pump. A demand pump is designed to run only when you are using water. When you open a faucet, the waterline pressure drops and the pump begins to run, and it will continue to run as long as the faucet is open. When you close the faucet, the line pressure backs up to the pump, and it shuts itself off.

The pump is self-priming and will run briefly to build up line pressure when the Water Pump switch is first turned on. See “Initial Waterline Priming” for instructions on using the water system for the first time.

5 - DASH / AUTO

Always fill the fresh water tank at an approved potable water filling facility or a known purified drinking water source.

7-1

SECTION 7 –

Water Pump Strainer

-Typical View

Unscrew bowl

and remove to

clean strainer

PLUMBING Water Pump Strainer

The pump is equipped with a cleanable strainer to capture any possible tank-borne particles that could damage pump components.

NOTE: We recommend that you check and clean

the strainer after each tankful of water during the first few uses of the Water Pump system. Thereafter, remember to check it at least yearly, and be sure to empty water from it during winterization procedures.

To Clean Pump Strainer

• Ensure all Water Pump switches are OFF.

• Twist the inlet cap (bowl) “counter-

clockwise” to unscrew from the strainer assembly.

• Remove the bowl and pull the strainer screen

out of the bowl to tap out any particles and rinse clean.

• Insert the strainer screen back into the bowl,

then screw the bowl back onto the strainer assembly.

NOTE: You must also empty the strainer when

winterizing your coach to avoid water freezing and cracking the filter bowl.

Water Pump Switch

The Water Pump switch is located near the monitor panel (some models may have an additional switch in the water service center, near the exterior shower, or within the bathroom area for your convenience).

While the switch is “ON”, the pump will automatically supply water as it is needed.

We recommend that you turn the Water Pump switch off whenever you will be away from the vehicle or not using the water system. In time, a slow leak in a faucet could drain the water tank, fill the holding tank, and discharge the house batteries.

Initial Waterline Priming

1. Ensure that all water drain valves are closed,

including water heater valve.

2. Turn Water Pump switch to “OFF” position.

3. Fill water tank.

4. Open all faucets, hot and cold.

5. Turn ON the Water Pump switch.

6. Close each faucet as it begins to deliver a

steady stream of water (close cold water first.) Leave hot water faucets on until they also deliver a steady stream of water. This will ensure that the water heater is filled with water.

7. Check to ensure the Water Pump stops soon

after all faucets have been closed.

8. The Water Pump is now ready for automatic

operation. The pump will start when a faucet is opened and stop when the faucet is closed.

Further Information

Refer to the Water Pump manufacturer’s operation, care, and maintenance information provided in your InfoCase.

7-2

SECTION 7 –

Water Pump

(Located beneath removable

access panel below bed)

-Model 23L shown

Water Pump

(Located beneath removable access

panel in pantry)

-Model 23B shown

Cold Water Filter Assembly (Located below galley sink)

NOTE: Hot waterline is not filtered.

• Insert new filter up into filter socket press and twist 1/4 turn “clockwise”.

PLUMBING

COLD WATER FILTER

–If Equipped

To obtain filtered cold water for drinking or cooking, simply open the galley sink cold water faucet.

Replacing the Cold Water Filter Cartridge

You should replace the filter cartridge every season and when water flow from the faucet is too slow for convenience. The cartridge must be replaced at least every 12 months.

• Place a container beneath the filter to catch

any water remaining in the waterlines during filter removal.

• T wist the filter cartridge “counter-clockwise”

about one-quarter turn, then pull it down and out of the filter socket.

• Insert a new water filter cartridge up into the

filter socket as far as possible and twist it “clockwise” one-quarter turn until it stops.

NOTE: Only the cold water faucet is filtered.

The cold waterline flows through an activated carbon filter that removes chlorine and odors for taste-free drinking water.

7-3

SECTION 7 –

Diverter Plug (installed in filter socket)

• Insert and twist 1/4 turn “clockwise”.

WARNING

PLUMBING

• Before using the water for drinking, run a few gallons of water through the filter and discard water to avoid consuming carbon dust or particles that may have been present in the new filter cartridge.

Diverter Plug

• Install the diverter plug into the filter socket for winterization or if water must be used while the filter is removed from the socket. The diverter plug is installed in the same manner as the water filter.

• See “Winterization Procedure” at the end of this section for further information.

• When removing the coach from storage, always disinfect and flush the water system thoroughly before installing a new filter. See “Disinfecting Your Fresh Water System” elsewhere in this section for more information.

NOTE: After the system has been thoroughly

flushed, remove the diverter plug and store for future use.

DISINFECTING YOUR FRESH WATER SYSTEM

(As required by NFPA®1 192 Standard on Recreational Vehicles)

To ensure complete disinfection of the potable water system, it is recommended that the following procedure be followed on a new system, one that has not been used for a period of time, or one that could have become contaminated.

This procedure is also recommended before long periods of storage, such as over winter.

Disinfecting with Gravity Fill

1. Prepare a chlorine solution using 1 gallon of

water and 1/4 cup of household chlorine bleach (sodium hypochlorite solution). With tank empty, pour chlorine solution into the tank. Use 1 gallon solution for each 15 gallons of tank capacity . This procedure will result in a residual chlorine concentration of 50 ppm in the water system.

If a 100 ppm concentration is desired as discussed in Step 4, use 1/2 cup of household bleach with 1 gallon of water to prepare the chlorine solution. One gallon of this solution should be used for each 15 gallons of tank capacity.

Chlorine is poisonous. Do not misuse. Recap bottle and clean all utensils after use.

2. Complete filling of tank with fresh water.

3. Open each faucet in the coach and run the

water until a distinct odor of chlorine can be detected in the water discharged. Do not forget the hot water faucets.

4. Let the system stand at least 4 hours when

disinfecting with 50 ppm residual chlorine. (If

a shorter time period is desired, then a 100

7-4

SECTION 7 –

Exterior Shower/Wash Station

(Typical)

PLUMBING

ppm chlorine concentration should be allowed to stand in the system for at least 1 hour.)

5. Drain the water tank and refill with fresh water.

6. Open each faucet again and run fresh water to flush chlorinated water from the lines. Run the water until there is no odor of chlorine detected in the water discharged. Do not forget the hot water faucets. (You may need to leave a hot water faucet

open for some time to flush the water heater with clean water. You may also want to turn the water heater off until this is done to avoid wasting energy trying to heat “unused” water).

7. Water system is now disinfected.

SHOWER HOSE VACUUM BREAKER

After using the shower, you may notice water dripping from the shower faucet assembly. The dripping results when vacuum in the shower hose (after closing the shower faucet) slowly releases and allows water remaining in the hose to drain down. This is a normal function of the shower valve assembly and is not a leak or defect.

If items are placed into the shower tub before shower valve vacuum release is complete, they may become wet.

TOILET

-If Equipped

The toilet in your motorhome is very similar to the household type, except that it is designed to use only a small amount of water per flush. It uses a high velocity jet of water, producing a swirl effect, to efficiently cleanse the bowl.

EXTERIOR SHOWER/WASH STATION

The exterior wash station feature allows you to do things such as rinse off sand or salt after a swim, rinse off muddy boots, or bathe your pet outside the coach. Some models may have a water pump switch located in the service center for convenience.

NOTE: The exterior wash station detachable

hose is stored in the rear of the vehicle.

Important “Don’ts”

• Don't use facial tissue or regular toilet tissue in the RV toilet. These will not disintegrate sufficiently and will often cling to the sides of the holding tank. Toilet tissue made specifically for use in RV toilets and holding tanks is available at most RV supply centers.

• Don’t dispose of sanitary napkins or other non-dissolving items in the toilet.

• Don’t put automotive antifreeze or caustic chemicals, such as laundry bleach or heavy detergents into the toilet or holding tank. These products may damage plastic or rubber parts in the system.

7-5

SECTION 7 –

Sewage Drain Outlet

(Located on the underside of water

service center)

-Typical View

Holding Tank Dump Valves

(Located in water service center)

-Typical View

1st - Pull Black Waste Tank Drain valve to drain

Black Water (sewage) tank – then close.

2nd - Pull Gray Waste Tank

Drain valve to drain Gray W ater

(sink/shower) tank – then close.

PLUMBING

See winterizing instructions at the end of this section to prepare the toilet for storage in freezing conditions.

Further Information

See the toilet manufacturer’s operation information in your InfoCase for complete operating, care, and maintenance information.

DRAINAGE SYSTEM (P-TRAPS)

Ensure there is an adequate amount of water in the drainage system p-traps to avoid sewer odor from entering your coach.

If you should experience a sewer odor, pour approximately 1 cup of water down each sink and shower drain in the coach.

WASTE WATER SYSTEM

(Holding Tanks)

The drainage system is self-contained and uses two separate holding tanks to contain the waste water until it can be dumped at an appropriate waste water disposal site. This means you can use the toilet, sinks and shower even in areas where utility hookups are not available.

The black water holding tank contains the sewage from the toilet and may include bathroom lavatory on some models. The gray water holding tank contains the waste water from the galley sink and shower, and may include bathroom lavatory.

See “Specifications” in Section 1– Introduction for tank capacities for your model.

3. Place the outlet end of sewer hose into disposal opening.

4. Open the Black W aste Tank Drain valve with a quick pull and make sure there are no sags in the hose. Move the hose gently about to dislodge any waste and ensure complete drainage. Close the Black Waste Tank Drain valve as soon as tank is empty.

Dumping Holding Tanks

1. Remove drain hose from water service center.

2. Remove dust cap from drain and connect sewer hose. Be sure it is firmly attached.

7-6

SECTION 7 –

WARNING

Holding Tank Heater Switch

(Located near monitor panel)

-Typical View

PLUMBING

NOTE: DO NOT OPEN BOTH VALVES AT

ONCE. Do not open the Gray W aste Tank Drain valve until the black tank is drained and dump valve closed to avoid sewage back-up into gray tank. Gray water also rinses any black water solids from the drain hose. Black and Gray tank valve positions may be reversed depending on floorplan and tank location.

5. Open the Gray W aste T ank Drain valve with a quick pull and make sure there are no sags in the hose to ensure complete drainage. Close Gray W aste Tank Drain valve as soon as tank is empty.

6. Add an odor control chemical to the sewage holding tank through the toilet. These chemicals are available at most RV stores.

7. Rinse sewage drain hose thoroughly with water and stow.

NOTE: We recommend that you dump all

holding tanks before traveling to avoid carrying unnecessary weight.

miles to dislodge the solids. A few starts and stops will aid in the process. Then reconnect the hose and drain in the normal manner.

NOTE: Always keep sewage drain outlet

capped while sewage connection is not in use.

Holding Tank Level Indicators

See “Systems Monitor Panel” in Section 4–

Appliances for further information on the

monitor panel and checking tank levels.

See “Specifications” in Section 1–

Introduction for tank capacities for your model.

HOLDING TANK HEATER

–If Equipped

Your coach may be equipped with black water and gray water holding tank heaters to allow use of waste utilities in freezing temperatures. The holding tank heater power switch is located near the monitor panel. The illuminated switch will glow when the power is on.

Using On-Site Sewer Hook-Ups

The sewage drain hose may remain attached to the sewage drain outlet while the motorhome is parked and connected to an on-site sewage hookup.

Service inlet access must be closed when utility connections are not in use.

When using a sewer hook-up, keep the dump valves closed until a tank becomes full or when preparing to leave the site. This keeps the solids in suspension, allowing them to be carried out with the liquids when the dump valve is opened. If the valve is left open, the liquids will drain off, leaving solids in the tank. Should this accidentally happen, disconnect the hose, fill the tank about half full with water, and drive a few

DO NOT operate the holding tank heater unless you are providing a supplemental 12-volt power source to recharge the house batteries. This means either the shoreline cord must be plugged into a 120-volt source, the auxiliary generator must be operating, or the chassis engine must be running (such as when driving down the road). This will prevent excessive discharge of the house battery.

7-7

SECTION 7 –

DRAIN

IN-LINE VALVE

LINE-END VALVE

Waterline Drain Valves

(Typical)

Waterline Drain Valve

Water Tank Drain Valve

Waterline Drain Valve

Water Tank Drain Valve

PLUMBING

NOTE: The holding tank heater pads are

electrical resistant-type heating elements. This type of heating element typically uses a large amount of current while operating. If the tank heaters are used without a recharging source, they will drain the house batteries in a relatively short period. Typically, the batteries would not support overnight heating without a supplemental charging source.

WATERLINE & TANK DRAIN VALVES

The waterline and tank drain valves are used to drain water from the water tank and the water supply lines when preparing the motorhome for storage or when sanitizing the water system.

See the “Water System Drain Valve Locations” chart at the end of this section for locations on your model.

Model 23B

Model 23L

7-8

WINTERIZING PROCEDURES

You can winterize the water and plumbing system of your coach using one of the following two methods – 1) Blow out waterlines using compressed air or – 2) Fill waterlines with RV water system antifreeze.

SECTION 7 –

Water Heater (Tankless) Power

Switch

PLUMBING

Method 1 – Blow Out Procedure

(Drain and purge waterlines using compressed air)

1. Level the Motorhome. If the coach is not

level, there may be “low points” in waterlines that can trap water in the lines and prevent it from draining properly.

2. Drain Fresh Water Tank and Waterlines.

Open all waterline drain valves and drain fresh water tank. (See “Water System Drain Valve Locations” chart at end of this section for locations of drain valves on your model).

3. Drain Exterior Shower/Wash Station.

Open exterior shower knobs, then point shower hose toward ground and squeeze handle to drain any water left in the shower line. Also, place the tip of your finger into the city water inlet and gently press the backflow valve “button” in the center of the inlet to drain any water trapped in the inlet line.

4. Remove the Cold Water Filter Cartridge (if equipped). Remove the filter cartridge from the filter assembly below the galley sink. (If your coach is not equipped with a cold water filter, continue to next numbered step.)

• Place a container beneath the filter to catch

any water that may drain from the waterline during filter removal.

• T wist the filter cartridge counter -clockwise

(to the left) about one-quarter turn, then pull it down and out of the filter socket. Discard used filter.

• Install the diverter plug into the filter socket. Insert plug up into the filter socket as far as possible and twist clockwise (to the right) one-quarter turn until it stops.

5. Open Faucets. Turn on the water pump and

open all sink faucets and shower head knobs. Leave open after water stops flowing.

6. Drain Toilet. Press the toilet flush pedal and

hold until water stops flowing in the toilet. Then turn water pump switch off.

7. Drain Water Heater (T ankless). Turn off the

Water Heater Power switch before draining the water heater and let the water drain through the system.

8. Connect Air Pressure. After water has

stopped draining at all faucets and drain valves, leave faucets open and connect a “blow-out” plug to the city water connection on the coach. Then use a compressed air hose regulated to 30 psi or less to force air through

7-9

SECTION 7 –

City Water Connection

Fresh Water

Inlet

Blow-out

Plug

Air Hose

PLUMBING

the system. A “blow-out” plug can be purchased at any Winnebago® or Itasca®

dealer.

NOTICE

Limit air pressure to 30 psi to avoid damage to equipment.

NOTE: DO NOT burst air into the system. This

can damage the water pump. It is better to let air in slowly.

9. Let air flow for five minutes until water is

completely drained out of faucets and drain valves. Then close faucets one at a time.

10. Drain Toilet. Operate and hold toilet flush

lever until water is completely drained from toilet.

11. Turn air pressure off. Disconnect water

purge adapters. Recap the city water inlet to avoid contamination by dirt or insects.

caustic chemicals such as bleach or laundry detergents into the toilet bowl or holding tanks. Although these products may have a deodorizing effect, they may damage plastic and rubber parts in the system.

14. Empty the water pump strainer filter bowl to avoid water freezing and cracking the filter bowl. See “Water Pump” previously in this section.

Dump and Clean Holding Tanks

15. Completely drain the sewage and waste water holding tanks at an approved waste disposal site. Drain the sewage tank first so the following waste water can rinse any waste solids from the dump outlet and sewer hose.

16. Close dump valves and refit the dust cap onto the drain outlet. This will inhibit rust formation on valve shafts and prevent entry and contamination by airborne debris, insects, and rodents.

Your drainage and fresh water systems are

now winterized.

See instructions for removal from storage in

Section 11 - Maintenance and Storage.

Method 2 – Antifreeze Fill Procedure

(Fill plumbing lines with RV water system antifreeze)

After Disconnecting Air Pressure

12. Close all waterline drains, tank drain valves, and all faucets to avoid contamination by dirt, insects, or rodents.

13. Pour about one cup of RV antifreeze down each drain for the galley sink, lavatory sink, and shower/tub. This fills the drain trap pipes to prevent holding tank odors from entering the coach during storage.

NOTE: It is not necessary to add antifreeze to

the toilet since the flush valve will be closed.

7-10

Do not add automotive antifreeze or

NOTE: As an alternative to totally draining the

waterlines, you may winterize tanks and lines by filling them with non-toxic RV water system antifreeze through the plumbing system. This product is available from your dealer and from most RV supply stores and national retail outlets. Follow directions on the container to determine the correct amount to use for your coach.

Your coach is equipped with a manually operated waterline winterization system for your convenience in winterizing fresh waterlines.

SECTION 7 –

WARNING

Antifreeze Siphon Tube and

Winterization Valve

(See Water System Drain Valve chart at the

end of this section for location on your coach)

-Model 23L shown

Antifreeze Siphon Tube

• Insert into container of RV water system antifreeze.

Winterization Valve

• Point toward antifreeze siphon tube for winterizing.

PLUMBING

The system features a Winterization (diverter)

valve with an antifreeze siphon tube to draw nontoxic RV water system antifreeze into the waterlines. There is also a Water Heater Bypass valve to avoid filling the water heater with antifreeze.

Leave Water Heater Bypass valve in

NORMAL FLOW position if draining water and blowing out waterlines. Place in BYPASS position ONLY when using antifreeze solution in waterlines.

NEVER use automotive antifreeze/ coolant in your RV water system. Automotive coolant/antifreeze contains ethylene glycol which, if ingested, can cause blindness and can be fatal.

Remove Water Filter

1. Remove and discard the filter cartridge from the cold water filter assembly below the galley sink. (If your coach is not equipped with

filtered cold water, continue to next numbered step).

• Place a container beneath the filter to catch

any water remaining in the waterlines during filter removal.

• Twist the filter cartridge “counter-

clockwise” about one-quarter turn, then pull it down and out of the filter socket.

• Install the diverter plug into the filter socket. Insert plug up into the filter socket as far as possible and twist “clockwise” one-quarter turn until it stops.

Set Up Winterization Valves

2. Remove and save the protective cap from the end of the antifreeze siphon tube (save cap to cover tube after use.) Insert the end of the siphon tube into a pail or other container with 2 to 3 gallons of non-toxic RV antifreeze solution.

3. Turn the W interization valve handle so that it points toward the siphon tube. (See “Water System Drain Valve Locations” chart at the end of this section for location on your model).

7-11

SECTION 7 –

Antifreeze Siphon Tube and

Winterization Valve

(See Water System Drain Valve chart at the

end of this section for location on your coach)

-Model 23B shown

Antifreeze Siphon Tube

• Insert into container of RV water system antifreeze.

Winterization Valve

• Point toward antifreeze siphon tube for winterizing.

Water Heater (Tankless) Power

Switch

PLUMBING

This will stop the flow from the antifreeze siphon tube and revert the tank line flow to the water pump.

9. Replace the protective cap onto the end of the antifreeze siphon tube to keep out insects or debris when not in use.

Drain Water Heater

10. Turn off the Water Heater power switch before draining the water heater tank to avoid damage to the heating element.

11. Drain W ater Heater (Tankless). Turn off the Water Heater Power switch before draining the water heater and let the water drain through the system.

NOTE: Ensure that all drain valves are

CLOSED before pumping RV antifreeze into the water system. Refer to the “Water System Drain Valve Locations” chart at the end of this section for valve locations on your model.

Fill Lines

4. Turn the Water Pump switch ON.

5. Open each hot and cold water faucet handle/ knob in the coach – one at a time each in turn until antifreeze solution just begins to flow from the faucet, then close. Do not forget exterior shower/wash station knobs (if equipped).

6. Press the toilet flush pedal and hold until antifreeze begins flowing into the toilet. Leave small amount of antifreeze that remains in the bowl.

When Done Adding RV Antifreeze

7. Turn Water Pump switch OFF.

8. Turn the Winterization valve so it points toward the waterline connected to the water pump.

7-12

Fill Drainage System P-Traps

12. Pour about one cup of RV antifreeze down each drain for the galley sink, lavatory sink, and shower/tub. This fills the drain trap pipes to prevent holding tank odors from entering the coach during storage.

Dump and Clean Holding Tanks

13. Completely drain the sewage and waste water holding tanks at an approved waste disposal site. Drain the sewage tank first so the following waste water can rinse any waste solids from the dump outlet and sewer hose.

14. Close dump valves and refit the dust cap onto the drain outlet. This will inhibit rust formation on valve shafts

SECTION 7 –

and prevent entry and contamination by airborne debris, insects, and rodents.

Your drainage and fresh water systems are

now winterized.

See instructions for removal from storage in

Section 11 - Maintenance and Storage.

WATER SYSTEM DRAIN VALVE LOCATIONS

Model System Drain Valve Locations

23B Waterlines Open drain valves under removable panel in lavatory.

Water Tank Valve behind vent on face of galley.

PLUMBING

Winterization (Antifreeze) Valve

23L Waterlines Open drain valves in rear passenger storage compartment.

Water Tank Valve under removable panel in galley. Winterization

(Antifreeze) Valve

Beneath pantry cabinet. Open lower cabinet door to access.

In rear passenger side storage compartment.

7-13

SECTION 8 – ENTERTAINMENT

12-Volt TV Master Power Switch

(Located in overhead cabinet

or on a wall near the TV)

-Typical installation shown

TV – 12V LED

-If Equipped

The LED flat panel TV is powered by 12-volt

DC current.

The 12-volt current is supplied from the house batteries, or from the power converter when connected to shoreline power or running the generator.

NOTE: The 12-Volt TV Master Power switch

must be ON to operate the TV.

TV – GALLEY (SWING-OUT)

–If Equipped (Typical View - your coach may vary in

appearance)

Your coach may be equipped with a TV swivel/telescoping mechanism, which allows you to angle the TV to best suit your viewing needs.

To Swivel TV

• Pull the black strap (located on back side of

TV) straight DOWN to release the TV from the mounting bracket.

NOTE: When the TV is not in use, the 12-Volt TV

Master Power switch should be turned OFF to eliminate drain on the 12-volt house battery.

Further Information

See the television manufacturer’s user guide provided in your InfoCase for complete operating instructions.

• Pull the TV out and pivot to desired position.

5 - DASH / AUTO

8-1

SECTION 8 –

Interior Speaker Switch

“SPEAKER A”

ENTERTAINMENT

• Rotate TV back to center position and press straight back towards wall. You will hear a “click” when the TV is secured into locked position.

Further Information

See the television manufacturer’s user guide provided in your InfoCase for complete operating instructions.

AUDIO-VIDEO SYSTEM BASIC OPERATION

NOTE: For your convenience, we have also

included a handy, tear -out version of this “A/V System Basic Operation” guide in Section 8 of your Operator’s Manual Supplement. See your InfoCase for specific operating guides for audio and video components.

DVD PLAYER WITH DELUXE SOUND

–If Equipped

The DVD Player is a selectable function of the multi-featured audio system. The player unit contains DVD/CD/MP3/AM-FM/USB/ Bluetooth Stereo. It also accepts portable audio player inputs and functions as an alarm clock.

This stereo receives Bluetooth streaming audio from Bluetooth enabled audio sources such as a cellphone.

The player is connected directly to the TV and can output sound to either the stereo speakers in the TV or to the Deluxe Sound speakers in the lounge area of the coach.

Refer to the manufacturer’s information provided in your InfoCase for complete feature descriptions and operating instructions.

Interior Speaker System

• T o connect or disconnect the interior speaker system, press SPEAKER A.

Set TV Video Input

• Turn TV and Radio/DVD player ON.

• Press the MODE button on the TV or the SOURCE button on the remote to select “INPUT 2”.

• The TV screen will display the DVD player logo when the correct input is selected.

Play DVD

• Insert a DVD “face up” into slot on lower face of the player.

• The DVD will begin to load automatically. The TV screen will typically display “Reading” or “Loading”.

• The DVD may load directly to the main title/menu screen or it may begin to play previews. You may be able to skip previews if desired by pressing the “Next” button on the DVD remote until you see the main menu screen.

• When the main menu screen appears, press the “Enter” button on the remote or “Play/ Pause” button on DVD player to begin playing the main feature. Use the arrow buttons on the DVD remote to select another feature to play .

8-2

SECTION 8 –

Exterior Speaker

(Located below patio awning)

-Typical View

WARNING

Exterior Speaker Switch

“Speaker C”

(Located on the interior stereo radio)

ENTERTAINMENT

• Volume is adjusted with the DVD remote.

TV Sound through Deluxe Sound Speakers

When watching TV programs alone, the TV normally plays sound through its own built-in stereo speakers. If you wish to connect TV stereo sound output to the Deluxe Sound speakers for a richer sound quality, follow these steps:

1. Turn the TV ON.

2. Make sure the Interior Speaker System is ON.

3. Press the AUX input selection button (located

just below the display on the face of the Radio/ DVD Player.) This will route the TV stereo sound output through the Radio/DVD Player and out to the Deluxe Sound speakers.

4. Select TV channels and adjust volume using

the TV remote.

Further Information

See the manufacturer’s quick reference guide provided in your InfoCase for complete feature descriptions and operating instructions.

EXTERIOR SPEAKERS

-If Equipped

Your coach may be equipped with two exterior speakers for outdoor listening pleasure (located below the patio awning) to provide outdoor usage of the interior stereo radio.

To connect or disconnect the exterior speaker system with the interior stereo system, press SPEAKER C (located on your interior stereo radio) as shown in the following photo.

Further Information

See the stereo radio information provided in your InfoCase for complete operating instructions.

TV ANTENNA - DIGITAL

(Jack® Digital HDTV Over-the-Air Antenna)

Your coach is featured with a digital antenna, which provides crystal clear digital HD reception of over-the-air channels in addition to superior broad reception range.

The digital antenna is equipped with a built-in amplifier for maximum VHF and UHF programming.

Never allow the antenna to touch electrical power lines or any other electrical wires.

Operating the Digital Antenna

1. Turn the Digital Antenna Power Switch ON.

8-3

SECTION 8 –

Digital Antenna Power Switch

(Located in an overhead cabinet or

mounted on a wall near the TV)

Digital Antenna Signal Meter

(Located on ceiling)

• Signal Meter Power Switch

• Attenuator Dial

• Release Button

• Rotational Knob (arrow

indicates which direction antenna is pointing)

TV Signal Amplifier Power Switch

(Located in an overhead cabinet or mounted

on a wall near the TV)

-Typical View

• Power Switch

ENTERTAINMENT

6. Rotate antenna to illuminate the last flickering LED light.

7. Repeat Steps 5 and 6 to pinpoint signal reception.

NOTE: Refer to television manufacturer’s

instructions to scan for available channels.

Further Information

See the antenna manufacturer’s user guide provided in your InfoCase for complete operating and maintenance information.

2. Turn ON the Signal Meter Power switch (located on the side of the Signal Meter).

TV SIGNAL AMPLIFIER

The TV Signal Amplifier is built into the antenna and can be turned on or off with a power switch located on a switchplate near the entertainment center cabinet.

An indicator light will illuminate when the switch is on and the signal amplifier is active.

3. Rotate the Attenuator Dial fully CLOCKWISE.

4. Press Release Button on the Rotational Knob and rotate antenna (until maximum number of LED lights illuminate on the Signal Meter).

NOTE: LED lights will illuminate from left to

right. All LED lights may not illuminate, depending on signal strength.

5. Rotate Attenuator Dial COUNTER-

CLOCKWISE until the last illuminated LED light flickers.

8-4

CABLE TV AND SATELLITE CONNECTIONS

The cable television and satellite dish input connections are located in the shoreline compartment.

EXTERIOR CABLE TV - 12V

Cable TV and Satellite Connections (Located in shoreline compartment)

Exterior Cable TV / 12-Volt Connection

(Located on passenger sidewall)

-Typical View

Interior Satellite Dish and HDMI Connections

(Located in an overhead cabinet or mounted

on a wall near the TV)

-Typical installation shown

• Satellite Dish Connections

•HDMI Connection

CONNECTION

–If Equipped

The exterior cable TV/12-volt connection receptacle on your coach provides connection for use of a TV and/or 12-volt device for your outdoor entertainment.

SECTION 8 –

ENTERTAINMENT

A second connection may be included inside a cabinet in the bedroom for the rear TV (if equipped).

See your authorized Winnebago Industries® dealer for proper installation and sealing of roof mounted components.

TV DIGITAL SATELLITE SYSTEM WIRING

Your coach is pre-wired for installation of a digital satellite TV system. Coaxial cable and high definition component cable connections are available to hook up your satellite receiver and are located near the entertainment center cabinet.

8-5

SECTION 9 – FURNITURE AND SOFTGOODS

Dinette seat back

WARNING

Dinette panel removed

DINETTE (REMOVABLE PANEL)

(Model 23B) (Typical View – Your coach may differ in

appearance)

The front dinette seat (located behind the passenger front seat) has a panel that may be removed for added foot space when the passenger seat is swiveled.

• Remove front dinette seat back from snaps and set

aside.

• Reverse steps to convert back to dinette seating.

• Slide removable panel upward to remove and set

aside. The panel may be stored below the dinette seat.

SLEEPING FACILITIES

Sleeping facilities are not intended for use while vehicle is in motion. For safety, passengers must use safety belted seating positions while vehicle is in motion.

5 - DASH / AUTO

9-1

SECTION 9 –

• Release Knob

T able Leg Release Button

FURNITURE AND SOFTGOODS

DINETTE/BED CONV ERSION

(Model 23L) (Typical View – Your coach may differ in

appearance)

Dinette and Table Extension

1. Pull release knob located on edge of dinette table.

Dinette to Bed

1. Store table if extended.

2. Lift forward facing dinette seat cushion.

3. Press the Table Leg Release Button and fold table leg UP until it “clicks” into locked (90degree) position.

2. Rotate table extension until it “clicks” into place.

Reverse steps to store table.

9-2

4. Remove dinette table from the wall support by lifting and pivoting the end of the table.

5. Lower dinette table to the floor. Then lower dinette seat cushion.

SECTION 9 –

FURNITURE AND SOFTGOODS

8. Cover bed area with side facing back cushion.

6. Cover dinette table with front facing dinette back cushion.

7. Pull to extend side facing dinette seat cushion.

Reverse steps to convert back into dinette

seating.

DINETTE/BED CONVERSION

(Model 23B) (Typical View – Your coach may differ in

appearance)

Dinette to Bed

1. Lift dinette seat cushions.

9-3

SECTION 9 –

Lift upward

Floor

Support

Bracket

T able Leg

Catch

Table

Bracket

Wall

Support

FURNITURE AND SOFTGOODS

2. Release the table leg from the floor support bracket.

3. Release the catch on the table leg brace and fold the leg up against the bottom of the table.

5. Lower dinette table to the floor.

6. Lower dinette seat cushions. Cover dinette table with front facing dinette back cushion.

4. Remove the table from the wall support bracket by lifting the end of the table.

9-4

7. Pull to extend sofa seat cushion.

SECTION 9 –

Loft Bed Switch

(Located above the microwave)

FURNITURE AND SOFTGOODS

8. Cover bed area with side facing back cushion.

Reverse steps to convert back into dinette

seating.

LOFT BED

(Model 23L) (Typical View – Your coach may differ in

appearance)

Loft Bed Operation

1. Remove side facing dinette back cushion and lay flat.

2. Push the Loft Bed Switch (located above the microwave) DOWN to lower the bed.

NOTE: The Power Loft Bed is not intended for

storage and should not be used for storage.

The Loft Bed is stowed near the cab ceiling as

shown in the following photo.

9-5

SECTION 9 –

WARNING

CAUTION

WARNING

Do not exceed 225 lbs. maximum weight capacity.

Misuse of ladder could result in death or serious injury.

See Operators Manual before using ladder.

FURNITURE AND SOFTGOODS

Keep people away from operating mechanism and pinch hazard areas during use. Failure to do so could cause injury.

3. The loft bed is now ready for use.

4. Reverse steps to store the loft bed.

NOTE: Allow lights to cool before storing bed.

Hot lamps can cause damage to material.

• Maximum Capacity: 450 lbs.

• To avoid injury to young children, do not leave them unattended on the loft bed.

NOTE: Your coach is equipped with a bunk

ladder. See “Bunk Ladder” in this section for operating instructions and safety precautions.

BUNK LADDER

(Model 23L)

The top of the bunk ladder must be hooked onto the edge of the bunk frame for use. The bunk ladder is located beneath the rear bed.

T o avoid injury , never use the bunk ladder in any other manner or for any other purpose than described in the following instructions.

Before Using Bunk Ladder

• Inspect the ladder to make sure it is not

damaged. Never use a damaged ladder.

• Keep the rungs of the ladder clean and dry

while in use. Do not step onto the rungs if the rungs are wet, or if your shoes are wet or carry debris that could result in a loss of footing.

• Never ignore warning labels or weight limits

defined on your ladder. The following warning label is located on or near the ladder:

• Maximum Capacity: 225 lbs.

• Do not overload. Ladder is intended for one

person.

• Make sure you are physically capable to

safely use the ladder . Strength, flexibility and stability are required.

• Grasp the side rails firmly and always use

both hands as you climb the ladder. Keep your body centered between the side rails. Do not over-reach.

• To protect children, do not leave the ladder

set up and unattended.

• Always store the ladder in a safe and dry

location when not in use. Stow properly while in transit.

• Do not store items on the ladder. You could

damage the ladder.

9-6

To Use the Bunk Ladder

WARNING

Loft Bed Switch

(Located near the entrance door)

1. Lift ladder horizontally.

2. Slide ends of ladder onto the edge of the bunk frame as shown.

SECTION 9 –

FURNITURE AND SOFTGOODS

3. Push the Loft Bed Switch (located near the entrance door) DOWN to lower the bed.

LOFT BED

(Model 23B) (Typical View – Your coach may differ in

appearance)

NOTE: The Power Loft Bed is not intended for

storage and should not be used for storage.

The Loft Bed is stowed near the cab ceiling.

Loft Bed Operation

1. Remove rear facing dinette back cushion and lay flat.

Keep people away from operating mechanism and pinch hazard areas during use. Failure to do so could cause injury.

4. The loft bed is now ready for use.

2. Remove sofa back cushion and lay flat.

9-7

SECTION 9 –

Pull Straps

-Typical View

FURNITURE AND SOFTGOODS

5. Reverse steps to store the loft bed.

NOTE: Allow lights to cool before storing bed.

Hot lamps can cause damage to material.

• Maximum Capacity: 450 lbs.

• To avoid injury to young children, do not leave them unattended on the loft bed.

NOTE: This low bunk design may be accessed

without the use of a ladder. If needed, a multi-purpose step stool may be used.

BED - ADJUSTABLE

(Model 23L) –If Equipped

(Typical View – Your coach may differ in appearance)

• Grasp the pull strap (located at the top of mattress) and pull up to desired angle of comfort (you will hear a “click”).

• T o return bed to the down position, pull strap all the way up and release in the lowered position.

ROLLER SHADES (MANUAL) SOLAR/BLACKOUT

–If Equipped

Your coach may feature two-stage day/night roller shades that provide both solar heat protection and light-blocking capabilities.

The shade can easily be lowered by hand to any position, then retracted with a slight downward pull movement. When raising the shade, there is no need to hold onto the bottom of the shade - just simply let it go and it will rise at a slow, controlled rate.

You can pre-set the auto-stop positioning of your shade, which allows your shade to retract to a cushioned stop, at the positioning of your choice.

9-8

SECTION 9 –

FURNITURE AND SOFTGOODS

Further Information

For further operating information and care instructions, see the manufacturer’s user guide provided in your InfoCase.

WOOD FURNITURE AND CABINETRY

–If Equipped

People are drawn to the natural beauty of wood. At Winnebago Industries®, our craftsmen work with the art found in each piece of wood to create cabinets of superior quality, backed by the Winnebago Industries warranty.

• Oak is a strong, open-grained hardwood that

ranges in color from white to pink and reddish tones. Streaks of green, yellow, and even black may appear due to mineral deposits. Oak may also contain wormholes and wild, varying grain patterns. This distinct graining is considered a desirable quality and has made oak one of the most popular woods used for cabinetry.

• Maple is a close-grained hardwood that is

predominately white to creamy-white in color, with occasional reddish-brown tones. While maple typically features uniform graining as compared to other wood species, characteristic markings may include fine brown lines, wavy or curly graining, bird's eye dots and mineral streaks. These traits are natural and serve to enhance maple's natural beauty.

Stains are likely to exaggerate the difference between open and closed grains and other markings in wood. Grain variation and color change should be expected. As hardwood ages, it will darken when exposed to different types of light. Color differences or changes in wood can also be caused by exposure to harsh chemicals, extreme heat, or other contributing external conditions.

Any color change that occurs in both the finish and the wood is considered part of the natural aging process and is not to be considered defect or damage.

Additionally, wood species exhibit other defining characteristics, such as mineral deposits/streaks, knots, sap runs, pin holes, and wormholes. These markings make the wood unique and contribute to its enduring beauty.

Therefore, since wood is a product of nature and will have certain natural characteristics and variances, they are not covered under the warranty.

• Cherry is characterized by its red undertones, but may vary in color from white to a deep, rich brown. Cherry is a close-grained wood with fairly uniform texture, revealing pin knots and curly graining. All wood will age with time and the finish will darken. This is especially true for cherry. This is a soughtafter quality in cherry cabinetry, and those who select it expect this evolution.

No matter which species you choose for your new Winnebago Industries motorhome cabinetry, please keep in mind that no two pieces of wood are exactly the same.

9-9

SECTION 10 – MAINTENANCE AND STORAGE

WARNING

SEALANTS – INSPECTION AND GENERAL INFORMATION

Water is a recreational vehicle’s worst enemy when it is allowed to enter where it is not intended. Sealants perform a very important function and should be inspected closely and maintained regularly. Winnebago Industries® utilizes many different types of sealants. Refer to the “Sealants Call-Out Sheet” provided in your InfoCase for further information.

Sealants, in general, do not have “set” lifetimes. Varying environmental factors affect the pliability and adhesiveness of sealants. You or your dealer must:

• Inspect all sealants, a minimum of every six

months.

• Inspect the moldings, windows, clearance

lights, exterior compartment doors, and all their attachments.

• Also, inspect weather seals around entrance

door, etc., and if necessary, have a dealer replace them immediately.

• Check for cracks, voids, gaps, breaks,

adhesion, and any sign of physical deterioration.

NOTE: Proper sealant inspection includes not

just visual observation but running a finger along sealant seams to verify proper adhesion to the surface. Any loosened areas must be replaced.

• Have the sealant replaced if you notice any of

the above. Your local Winnebago Industries dealer has the correct and necessary parts and experience to help you maintain your sealants. See “Sealants Call-Out Sheet” provided in your InfoCase.

• Always use the same type sealant that was

removed.

• Immediately have dealership check moldings,

windows, and exterior attachments for leak source if you notice water inside of unit.

NOTICE

Sealants must be inspected every 6 months and replaced if necessary.

ROOF

STAY OFF ROOF. Surface may be slippery. Falling could result in death or serious injury.

The roof is made of Thermo-Panel materials like the walls and floor. It will support the weight of an average adult for periodic maintenance or repair of the roof or roof mounted components.

For your safety, it is not recommended that you store or carry items on the roof.

Always have damage to the roof area repaired immediately. Damaged or detached sealant around the vents, air conditioner, body-to-roof seams, etc., should also receive immediate attention. Delaying these repairs may allow water leakage and result in damage to interior ceiling and body panels, upholstery, etc., which is not covered by the limited warranty (see” New Vehicle Limited Warranty” provided at the beginning of this manual).

UNDERCARRIAGE

Buildup of mud and dirt under the body of the vehicle can cause damaging rust or corrosion on steel or aluminum parts and can add needless

5 - DASH / AUTO

10-1

SECTION 10 – MAINTENANCE AND STORAGE

weight to the vehicle. This, in effect, reduces the amount of cargo you can carry and remain within GVWR and GAWR limits.

Corrosive materials, such as those used for ice and snow removal and dust control, can also accumulate on the underside of a vehicle. These materials should be removed by flushing the undercarriage regularly with water, especially horizontal surfaces, cavities, and other areas where mud and other deposits may collect.

EXTERIOR AUTOMOTIVE PAINT FINISH

The body of your coach is fully or partially finished with the highest quality automotive paint and clearcoat. Follow these precautions to keep the finish on your coach looking its best and preserve maximum gloss and durability.

Parking

• Avoid parking under trees – When this

happens you should rinse the bird droppings and tree sap off as soon as possible. Tree sap is a form of sugar and will dissolve after a couple of rinses. Bird droppings can eat into a painted surface if left unattended and need removed as soon as possible. Lukewarm soapy water can help speed up the cleaning process.

• Avoid parking near salt spray – When this

happens you need to rinse off the salt mineral residue to minimize the corrosiveness of the salt.

• Avoid parking near factories with heavy

smoke or industrial fallout – Industrial fallout can eat into your coaches finish when dew or rain mixes with it to create nitric or sulfuric acid that gets magnified by the intensity of the sun. As the water evaporates, the acid becomes more powerful and attacks the painted surface. Rinsing and washing the surface helps remove the fallout and neutralize the acid. After the initial 60-day cure stage, a coat of wax or polish can help protect the surface from these types of contaminates.

• Do not scrape ice or snow from the painted surface. Brush off gently with a soft-bristled snow brush – avoid being forceful with the brush. If brush scratches show after the motorhome thaws out, it may be possible to remove them by hand waxing with a silicone-free liquid wax.

• A void covering painted surface. When paint is covered (especially in outdoor conditions), water may appear between the cover and the vehicle due to rapid temperature fluctuations. The water may vaporize under certain conditions and migrate into the painted surface, possibly resulting in blisters and/or bubbles in the paint. These blisters/bubbles are not covered under warranty. Covering your RV is at owner’s risk.

Driving

• Avoid driving on gravel roads.

• Rinse off bugs and bird droppings with water daily.

• Antifreeze, fuel, or windshield/window solutions spilled on the painted surface should be rinsed off immediately with water and allowed to air dry. Wiping dry with a towel may create fine scratches due to the solvent nature of these types of fluids.

• Fuel cannot be diluted and dissipated with water . It must be removed with a mineral spirit type cleaner (such as SEAFOAM Bugs-B- Gone, or equivalent) or a silicone-free spray wax and microfiber cloth to remove the stain left by fuels.

• Ensure that all RV fluids (such as gas, oil, grease, antifreeze, transmission fluid, brake fluid, etc.) are completely wiped off of painted surfaces. Failure to comply may cause the paint to blister and/or peel.

NOTE: When driving in wintry conditions, the

road surface may be covered with heavy salts or small rocks to improve road traction. These types of road conditions can cause undue surface damage to your RV. Please refrain from driving in these conditions.

10-2

SECTION 10 –

MAINTENANCE AND STORAGE

Washing

• Commercial vehicle wash facilities should be strictly avoided! They will scratch your RV!

Truck-style wash centers have highpressure wands that emit higher than necessary water pressures and the brushes are very aggressive. Most truck wash brushes are made from a heavy plastic for durability and are under heavy pressure. They are designed to clean heavy road films on semi trailers and are often dirty. They are not designed for custom painted RV’s and they will scratch the clearcoat finish. Many times these scratches can penetrate the clearcoat finish, possibly causing delamination and/or other paint related issues that are not covered under warranty.

• Wash your RV with cool or lukewarm water using a mild soap (such as a baby shampoo) that does not contain bleach solution. Most auto stores offer car wash detailing soaps that are similar and do not have bleach in the formulation (such as Meguiars #62).

• Never use a bristled brush or broom to wash the painted surface. This will cause scratches in the finish. Using a microfiber cloth, mitt, or mop is strongly recommended.

• Be sure your cloth or applicator is clean. A dirty applicator can scratch your RV.

Washing Procedure

• Rinse area to be washed with cold water to remove surface residue. Ensure you are not in direct sunlight.

• With area to be washed still wet from the rinse, use the recommended soapy mixture to clean the area. T o avoid scratching painted surfaces, a microfiber cloth, mitt, or mop is strongly recommended to apply soapy water.

• Rinse washed area before soap evaporates.

• Dry the rinsed area before the water evaporates.

NOTE:Avoid aiming water flow from a hose or

spray from high-pressure washing equipment into any appliance intake, as damage or difficulty in operating appliances may occur.

• After washing the coach, carefully inspect sealant around window frames, vents, and any other joints that may have loosened or separated. See “Sealants - Inspection and General Information” at the beginning of this section for details.

Bug Removal

• Rinse any loose debris off with water and allow the remaining residues to soak and soften. Use soap and water to wash the residue, then rinse.

NOTE: You may wish to repeat and leave soap

on longer than normal to help with softening hardened residue.

• For more stubborn areas, use an ammoniabased glass cleaner followed by washing with warm soapy water, then rinse.

• Remember to use microfiber towels during this process to help avoid scratches.

• If this does not work, as a last resort, use a bug removal product (like SEAFOAM Bugs-B- Gone, or equivalent) in a shady area and follow the directions on label. Ensure cleaner is completely wiped off of painted surfaces. Failure to comply may cause the paint to blister and/or peel.

Polishing and/or Waxing

NOTE:When your coach is new or has been

repainted for any reason, no polish or wax should be applied to the finish until after a 60-day cure cycle at temperatur es higher than 60 degrees for 60 days. Failure to observe this precaution could void your paint warranty.

• W e recommend a silicone-free polish with an orbital machine and terry cloth applicator.

• Liquid waxes are easier to apply and bring to a gloss with fewer residues.

10-3

SECTION 10 – MAINTENANCE AND STORAGE

• Avoid paste waxes. They sometimes have fillers and additives that give a very short term result. Stay away from silicones in polishes and soaps.

• Buffing compounds remove some of the mil film of the clearcoat, so we recommend that only professionals or very experienced users apply this type of product.

Inspection

A motorhome exterior is subjected to many physical forces and environmental conditions. While the coach is parked, it is exposed to climate and weather extremes and other environmental conditions. While in operation, it is subjected to various twisting and flexing forces caused by routine cornering and turning, and by uneven road surfaces, such as bumps, potholes, railroad tracks, and parking lot entrances.

Inspect the exterior fiberglass shell periodically for cracks which may represent a threat to the integrity of the fiberglass.

Minute cracks in the surface (commonly referred to as "spider cracks" or "hairline cracks") caused by normal flexing of the fiberglass exterior are normal and typically pose no threat to the integrity of the vehicle other than appearance.

However, if a crack has opened up and the weave of the cloth is visible, this does represent a threat to the integrity of the fiberglass and must be repaired or covered as quickly as possible to avoid penetration by moisture, especially in freezing climates.

If the fiberglass has been damaged and contains cracks, tears, or holes, use plastic sheeting and duct tape, if necessary, to prevent moisture from damaging the sidewall material or the interior of the coach.

Protective Film

-If Equipped

Your coach may be equipped with a protective film to defend against everyday road hazards. This film creates a barrier against bugs, road grime, bird droppings, and other harmful elements.

Further Information

See the manufacturer’s information provided in your InfoCase for complete care and maintenance instructions.

EXTERIOR GRAPHIC CARE

The pressure-sensitive graphics on your vehicle require very little maintenance. In order to allow the graphics to have the longest life possible, the following steps should be taken.

• Wash graphics with plain soap and water or

any car wash detergent. Rinse thoroughly.

• High pressure water spray may loosen or

damage graphics. Keep spray nozzle at least 1 1/2 feet from the edge of the graphics.

• T est any cleaning solution on a small section

of graphic before using.

• Never use aromatic solvents such as acetone,

M.E.K., toulene, paint thinner or lacquer thinner on graphics. Solvents may soften the vinyl and smear colors.

• Gasoline or other fuels spilled on graphics

should be rinsed off immediately with water.

• Do not apply paint or clearcoat over the

graphics.

• Do not apply wax over the graphics,

especially wax containing petroleum distillates. Wax that has dried along the edge of a graphic can be removed with cotton swabs after softening it with isopropyl alcohol. Rinse area thoroughly after cleaning.

PLASTIC PARTS – CLEANING

Many parts in your vehicle, such as the dash, exterior light lenses, and certain exterior body panels are made of high-impact plastic materials that can be damaged by wiping with solvents or improper cleaning products.

Always try cleaning plastic parts with the mildest cleaners first and work your way up to stronger cleaning products. Use the following cautionary lists as a guide when selecting cleaning products to use on plastic parts.

10-4

NOTICE

Do not use citrus-based cleaners on polycarbonate finishes. Citric compounds will damage the high-gloss surface, causing it to appear dull or “flat”. Always test a cleaning product on a hidden area to be sure it will not cause damage to the appearance of the part.

Here is a list of mild cleaners that may be used safely:

• Car washing soap and water

• Glass cleaners without ammonia

• Mineral oil

• Multipurpose cleaners (such as Fantastik®, Formula 409®, etc.)

The following products, compounds, or solvents must be wiped off immediately to avoid damage:

• Ammonia

• Brake fluid

• Bathroom basin, tub, and tile cleaners

• Chlorine

• Ethyl alcohol

• Isopropyl (rubbing) alcohol

• Kerosene or gasoline

• Naphthalene

• Pine-type household cleaners

Do not use cleaners containing the following products, compounds, or solvents. These products will damage the finish.

• Acetic acid

• Acetone (nail polish remover)

• Aromatic solvents (lacquer thinners)

• Benzene

• Butyl alcohol

SECTION 10 –

MAINTENANCE AND STORAGE

EXTERIOR LIGHTS

Most Winnebago Industries® vehicles have polycarbonate lenses on exterior lamps, which are very sensitive to a variety of chemical solvents and cleaners.

Use only soap and water to clean exterior lamp lenses, especially headlights.

• Contact with certain chemicals can cause

etching, “crazing” or cracking of the lens, which can significantly reduce the lens clarity and effectiveness of the lamp and may require replacement of the complete lamp housing.

• Some popular citric acid cleaners may cause

polycarbonate lenses to become “hazy” or “foggy”.

• Do not use a pressure washer to clean

headlights.

• Inspect and operate the lights regularly to

confirm proper operation and mounting condition.

INTERIOR SOFT GOODS

We recommend a weekly routine of vacuuming all fabrics and carpet throughout the motorhome to prevent an accumulation of dirt, which can detract from the appearance and shorten the life of carpet and fabrics.

Fabric Upholstery

Some fabrics used in this motorhome may contain fire retardant and lightfastness additives, which can be damaged by use of improper cleaning products. Some water-based household cleaning products are not formulated for use on fabrics and may cause excessive shrinkage or fading. Always test any cleaning product on a hidden area of fabric before using on visible areas. For best results, fabric cleaning should be referred to a professional carpet and upholstery cleaner.

NOTE: T o minimize fading of upholstery , carpets

and other interior fabrics caused by excessive sunlight, the drapes, blinds, or

10-5

SECTION 10 –

WARNING

MAINTENANCE AND STORAGE

shades should be closed when the motorhome is parked for an extended period of time.

When cleaning upholstery and fabric, do not use lacquer thinner, nail polish remover, lau ndry soaps, or bleach. Never use carbon tetrachloride, gasoline, or naphthalene for any cleaning purpose. These materials may cause damage to the material being cleaned and most are highly flammable, posing risk of injury due to fire.

Ultraleather

Leather-Like Upholstery

Ultraleather synthetic leather fabric material has the luxurious look and feel of the finest European calfskin, with the durability and resistance to soils and stains of vinyl fabrics. It is also tougher than real calfskin and has superior resistance to punctures, snags, and rips.

For most soils and stains, the fabric manufacturer recommends spot treatment with a solution of water and Tide® brand laundry detergent or equivalent. More stubborn stains may be treated with a water-based multipurpose cleaner/degreaser such as Simple Green equivalent. Solvent cleaners such as nail polish remover or other aromatic solvents are not recommended.

UltraLeather Cleaning Chart

Detergent/

Type of Stain

Coffee, Tea  Red Wine, Liquor  Cola, Soft Drinks  Milk  Ketchup  Steak/Soy Sauce  Mayonnaise, Butter  Salad Oil  Chocolate  Cosmetic Makeup  Lipstick  Face Cream  Suntan Oil/Lotion  Shoe Polish  Urine  Machine Oil 

Water

Cleaner/ Degreaser

Vinyl Fabrics (including ceiling)

Vinyl should be cleaned with a soft, damp cloth, and a mild detergent only. Do not use solvents. Solvents may damage the surface of the vinyl.

Draperies, Curtains, and Bedspreads

These items may be woven from a variety of fabrics. We recommend that these be professionally dry cleaned only. A five percent shrinkage may occur when you have these items dry cleaned.

Care Instructions

• Spot clean with mild soap and water.

• Air dry or, if desired, dry quickly using a hair dryer on warm setting - not hot.

• For stubborn stains, use cleaner-degreaser.

10-6

General Stains

As with any stain or contamination, the quick response is the best, especially when done in conjunction with the proper cleaner for the type of stain.

CABINETRY – CLEANING

Wooden items may be cleaned with a soft cloth and a good quality wood finish cleaning product.

SECTION 10 –

MAINTENANCE AND STORAGE

Vinyl simulated wood panels may be cleaned with a mild, water-based cleaner and a soft cloth. Do not use solvents on vinyl wood panels.

NOTE: Many cabinetry and furniture items

throughout this motorhome are constructed either partially or completely of real hardwoods. Because of natural variations in woodgrain density, slight differences in stain hue may exist between one item and another. This is the distinctive character and beauty of real wood.

TABLES AND COUNTERTOPS

Work surfaces are covered with a plastic or thermo-formed laminate that resists solvents, stains, and abrasions. A coat of furniture wax applied to these surfaces on the counters and table will help preserve their beauty and make cleaning easier. Always clean the surface before applying wax.

STAINLESS STEEL APPLIANCES

-If Equipped

Care and Maintenance

You can easily maintain the beauty of your stainless steel appliances with little effort, under most circumstances, by performing the following recommendations.

Typically, excellent results can be obtained by washing stainless steel with mild dishwashing liquid and hot water, followed by rinsing thoroughly and drying with a soft cloth. Drying is particularly important if the tap water is very hard and leaves scale deposits.

Stainless steel does not deteriorate due to frequent cleaning, so proper cleaning can be performed whenever necessary. For more stubborn stains, perform the following procedures for your stainless steel appliances to start shining again.

Scale

To remove scale left by water, simply use a multipurpose cream detergent and a soft cloth. Thicker scale may be removed by generously applying 25% vinegar and hot water solution to the stain. Rinse thoroughly with a sodium bicarbonate and water solution, then follow up by rinsing with water. Clean carefully.

Oil and Grease Stains

To remove oil and grease stains, use a mild dishwashing liquid and hot water. Rinse thoroughly with clean water and dry with a soft cloth. For more stubborn stains, ethyl alcohol, acetone, or another non-halogenated solvent may be used with care.

Stubborn Dirt and Burnt Grease

Use a multipurpose cream detergent and a soft cloth.

Coffee and Tea Stains

Prepare a sodium bicarbonate solution and hot water. Apply generously to stain and let sit for 15 minutes. Rinse thoroughly and dry with a soft cloth.

Rust Stains

Apply a multipurpose cream detergent and rub delicately with a soft cloth. If stain persists, it may be necessary to apply a stainless steelspecific product.

Fingerprints

Use a mild dishwashing liquid and warm water. Rub delicately with a soft cloth. Window cleaner may also be used.

Scratches

Apply a stainless steel-specific detergent/ polisher and buff with a soft cloth.

Important “Don’ts”

• Do not use hydrochloric acid or any other

detergents containing chlorides on stainless steel.

• Do not use abrasive powder detergents that

could ruin the surface finish.

10-7

SECTION 10 – MAINTENANCE AND STORAGE

• Do not use wool, abrasive brushes, or tools that have previously cleaned other metals, because as well as scratching the surface, they can generate contamination and unattractive stains.

• Do not use silver cleaners.

VINYL FLOORING

Care and Maintenance

You can easily maintain the beauty of your vinyl flooring with little effort, by following these recommendations:

GALLEY SINK

Stainless S teel

Care and Cleaning Instructions

The stainless steel sink can usually be cleaned with water and soap or detergent using a soft cloth or sponge.

• Rinse thoroughly with warm water and wipe

dry quickly to avoid spots and streaks.

• For stubborn stains, use a mild abrasive

cleanser like Soft Scrub®, Comet®, etc. W ork in the direction of the “grain” of the brushed finish lines.

• Never use steel wool. Particles of steel from

the wool pad can embed into the sink surface, then become rusty and unsightly.

• Avoid contact with full-strength bleaches,

household chemicals, and acid-based cleaners. If this happens, rinse and wipe dry quickly.

• Salt, mustard, and mayonnaise can cause

pitting if left on the steel sink surface. If spilled, clean and rinse immediately.

• A high iron content in the water (hard water)

may result in a brown or rust-colored stained appearance. If noticed, dry towel sink after each use.

• Do not use rubber mats in the sink bowl.

Material trapped under mats can complicate cleaning.

NOTE: Improper use may damage this product

and void the warranty.

• Sweep or vacuum floor daily (use a vacuum without a beater bar head.) Remove loose dirt with a soft brush or Swiffer® type product.

• For more intense cleaning, use a non-abrasive cleanser, such as Mr . Clean®. Rinse with clean water.

NOTE: Floor cleaners containing waxes,

brighteners, or gloss agents are not recommended.

• Regular cleaning with solvent-based chemicals may adversely affect the topcoat performance.

• Do not use undiluted bleach or leave a dilution of bleach on the floor for longer than one hour .

• V inyl flooring is extremely durable and long lasting. It is normal for the floor to show some denting and dimpling where furniture sets due to the soft nature of the material. The dents are not permanent and will come out over time.

Maintenance Tips

• Install protection (such as pads or casters) on furniture with legs or sharp edges. This protection should not contain bitumen, which may cause brown stains.

NOTE: Faulty pads and casters should be

removed and replaced.

• Burning cigarettes and matches can cause damage to the flooring.

• Use doormats (that do not contain bitumen) to keep out most of the dirt and dust.

• Remove spills immediately with a damp cloth, followed by rinsing with clean water.

RANGE AND REFRIGERATOR

For care and appearance maintenance of the range and refrigerator, refer to the appliance manufacturer’s operation and maintenance manuals included in your InfoCase.

10-8

• The use of stiletto heels is not recommended, as they may cause permanent damage to the flooring.

• Protect flooring from prolonged direct sunlight exposure.

SECTION 10 –

MAINTENANCE AND STORAGE

Treatment of Stains

Acids, alkali, alcoholic beverages, coffee, soft drinks, ketchup, fruit, fruit juices, food, vegetables, mustard, ink, and iodine:

• Remove the stain with lukewarm water and a cloth or sponge. If necessary , clean with a soft nylon pad and non-abrasive mild detergent or resilient floor cleaner.

Heel marks:

• Clean as soon as possible with a soft nylon pad and non-abrasive mild detergent or resilient floor cleaner.

Asphalt, candle grease, chewing gum, fat, oil, tar, and shoe polish:

• Gently remove with a blunt instrument and treat with a soft nylon pad and non-abrasive floor cleaner.

Lacquer and nail polish:

• Remove as soon as possible. Do not allow to dry. If necessary, apply nail polish thinner (sparingly) to remove any residue.

Tub and Shower Walls

The tub and shower walls in the bathroom should be cleaned with mild soap and warm water. Do not use an abrasive cleaner on the shower walls and tub, as scratching and discoloration may occur. Stubborn stains may be removed with an automotive-type cleanser.

Lavatory Sink - Fiberglass

General Cleaning

Clean often with hot water and soap. If a cleanser is necessary, make sure the product is recommended for use on plastics.

Avoid harsh abrasive cleaners, ammonia, or citric-based products as discoloration may result.

Rinse all food, beverage, or cosmetic residue from the sink as soon as possible. Some residues, if left to sit in the sink, may require the use of detergent or mild liquid or gel-type kitchen surface cleaner.

If acids or medicine spill on the surface, wash the spills immediately.

Corrosion, paint, and grass stains:

• Treat as soon as possible with a soft nylon pad and non-abrasive mild detergent or resilient floor cleaner.

Varnish, oil paint, and solvents:

• Blot up as soon as possible. Do not rub, as this will only spread material further across the surface. Carefully treat with a mild cleanser. When dry, carefully peel the stain off. MEK may be used sparingly, if necessary. Rinse immediately with clean water.

Pet stains:

• Treat with lukewarm water. If stain remains visible, clean with a soft nylon pad and nonabrasive resilient floor cleaner.

BATHROOM

Toilet

For instructions on the care of your toilet, refer

to the information in your InfoCase.

Marks or Discoloration

A color-matched automotive scratch remover compound may be used to remove stubborn marks or discoloration. Always follow label directions.

NOTE: Do not use steel wool or metal scouring

pads.

DOORS AND WINDOWS

Windows may be periodically cleaned with a good quality glass cleaner or mild soap solution using a soft cloth.

Use care when removing ice or frost from the windows. Always use a plastic ice scraper, never one made of metal. Use care when removing ice from the mirrors to protect the reflective surfaces.

Door locks and hinges should be lubricated periodically with powdered graphite to ensure trouble-free operation and to protect against freeze-up.

10-9

SECTION 10 – MAINTENANCE AND STORAGE

VEHICLE STORAGE – PREPARATION

Properly preparing your vehicle for storage will lessen the possibility of damage to your vehicle. Prepare the motorhome for vacancy just as you would if you were leaving your house for an extended period.

Clean and Prep Coach for Storage

1. Turn off the propane gas tank.

2. Turn the furnace thermostat switch OFF.

3. Remove all foods and items that may cause

odors from cabinets and refrigerator.

4. Clean and defrost the refrigerator. Prop the

door open slightly to allow any odors to dissipate. Place an open box of baking soda inside the refrigerator to help absorb odors.

5. Fully charge the batteries. Batteries must

have at least 80% charge to survive freezing temperatures and long period of non-use. We recommend that you connect a

battery charger or plug in the shoreline once a month during long-term storage periods to maintain battery charge and to avoid sulfating. If connecting a charger directly to batteries, turn the House/Coach Battery Disconnect switch off to avoid electrical arcing when attaching and detaching charge clamps.

NOTE: We do not recommend leaving the

shoreline plugged in continuously during storage.

6. After charging batteries, turn the House/

Coach Battery Disconnect switch off to disconnect the batteries and avoid parasitic* drain.

* Parasitic battery drain is the gradual drain

by items connected directly to battery power such as clocks, radio memory, and the engine computer.

7. Have the vehicle chassis completely serviced

and lubricated. Be sure radiator antifreeze protection level is sufficient for the lowest anticipated temperatures.

8. Wash and wax the coach.

9. Inspect all seams and seals around doors, windows, vents, and any other joints. Replace or repair any that are damaged. Sealing materials and compounds can be purchased from your dealer. Badly damaged weather seals may need to be replaced by your dealer .

10. Close all windows and roof vents. Protect all appliance vent openings from contamination by animals or insects (e.g. bird nest, wasp nests, etc.)

11. Lubricate all door hinges and locks.

12. Clean the interior of the coach. Dirt and stains are more easily removed when fresh.

13. Follow “Vehicle - Leaving in Storage” suggestion in chassis owner’s manual included in your InfoCase.

If you are storing your vehicle through the winter, or in cold climates, extra preparations must be made to protect equipment and systems that can be damaged by freezing temperatures. See Winterizing Procedures in Plumbing section.

VEHICLE STORAGE – REMOVAL

1. Completely air out the motor home.

2. Have the entire LP gas system checked for

leaks.

3. Check window operation.

4. Check cabinet and door hinges. Lubricate

with penetrating oil, if necessary.

5. Close all faucets and drain valves that are

open.

6. Add a few gallons of water to the fresh water

tank and turn on the water pump to check for leaks, especially at fittings.

7. Open all faucets in turn to release trapped air

and check to be sure faucet washers have not hardened during storage.

8. Sanitize the water system as outlined under

Disinfecting the Fresh Water System in the Plumbing section, then flush the waterlines thoroughly with fresh water.

10-10

9. After flushing fresh waterlines, install a new water filter cartridge on the galley sink water filter and/or full-coach water filteration system (if equipped). See appropriate filter installation instructions in Plumbing section.

NOTE: Always purge a new filter with clean

running water before using. See filter manufacturer’s directions included with the filter cartridge.

10. Check the toilet for proper operation.

11. Add water to the holding tank using the toilet flush pedal and galley sink faucet. Check to be sure dump valves seal tightly.

12. Check around all appliances for obstructions and ensure that all vent openings are clear.

13. Start refrigerator and check for proper cooling.

14. Clean wall and counter surfaces.

15. Replace batteries, if necessary , and check out electrical system to make sure all lights and electrical components operate.

16. Check tires for proper cold inflation pressure. See “V ehicle Certification Label” in Section 1

- Introduction.

17. After washing accumulated winter grime from the vehicle, it is important to carefully inspect the seams and sealants for separation or cracks that may have appeared around the window frames, vents, and any other joints. See Sealants – Inspection and General Information at the beginning of this section. Resealing is quite simple and the material is quickly and easily applied. Appropriate compounds are available from your dealer. See the Sealants – Recommended Application page in the Supplement Manual provided in your InfoCase. Also inspect weather seals around doors, etc., and if necessary, have a dealer replace immediately.

SECTION 10 –

MAINTENANCE AND STORAGE

CHASSIS SERVICE AND MAINTENANCE

Consult the appropriate sections in your chassis manual for specific information regarding operating safety, service recommendations, and maintenance schedules for the chassis section of your vehicle.

10-11

SECTION 10 – MAINTENANCE AND STORAGE

COACH MAINTENANCE CHART

These recommendations apply for normal recreational use. Heavy duty or full-time use may require more

frequent maintenance intervals.

s Necessary

Always use specified sections or manufacturer’s

guide for further information and instructions.

Before Each

Use

Weekly

Monthly

Every 3

Months

Every 6

Months

Every Year

Propane Gas System

Have propane gas system checked for leaks  Pressure Regulator - inspect and adjust if needed  Check propane tank condition, mounting, and fittings 

Electrical System

Check Battery Condition Meter  Check battery fluid level and connections  Check 12V fuses and 120V breakers  Check GFCI receptacles 

Generator

Visually inspect generator and compartment  See generator manufacturer’s maintenance guide 

Plumbing System

Sanitize plumbing system  Winterize plumbing system  Clean water pump strainer filter 

Slideout & Leveling System

Check and adjust  Check hydraulic oil level  Check hydraulic lines (routing, leaks, etc.)  Inspect slideout room seals (bulb seals), clean as nec-

essary Check and inspect electric slideout lock drain line(s) 



Exterior

Clean roof  Clean sidewalls  Clean windows  Flush underside of vehicle 

10-12

SECTION 10 –

MAINTENANCE AND STORAGE

COACH MAINTENANCE CHART

These recommendations apply for normal recreational use. Heavy duty or full-time u se may require more frequen t maintenance intervals.

As Necessary

Always use specified sections or manufacturer’s

guide for further information and instructions.

Before Each

Use

Weekly

Monthly

Every 3

Months

Every 6

Months

Every Year

Safety Equipment

Check operation of the following items:

Headlights, Taillights, and Marker Lights  Turn Signals  Horn  Hazard Warning Flashers 

Windshield Wipers and Washers  Fire Extinguisher - check charge indicator  Smoke Alarm - test operation *  Carbon Monoxide Alarm - test operation *  Propane Gas Leak Detector - test operation  (*replace battery if needed)

Appliances

Water Heater

See water heater manufacturer’s maintenance guide  Inspect and clean exterior vent 

Refrigerator

See refrigerator manufacturer’s maintenance guide  Inspect and clean exterior vent/drip tray drain tube 

Furnace

See furnace manufacturer’s maintenance guide  Inspect and clean exterior vent 

Air Conditioner

See A/C manufacturer’s maintenance guide  Inspect for exterior damage  Check/replace filter 

Range Top

See range manufacturer’s maintenance guide  Inspect and clean/replace range hood grease filter 

10-13

SECTION 10 – MAINTENANCE AND STORAGE

COACH MAINTENANCE CHART

These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals.

s Necessary

Always use specified sections or manufacturer’s

guide for further information and instructions.

Before Each

Use

Weekly

Monthly

Every 3

Months

Every 6

Months

Every Year

Sealants

Inspect (see “Sealants - Inspection and General Information” at the beginning of this section for proper inspection technique)

Replace (see “Sealant Call-out Sheet” in the supplement manual provided in your InfoCase)





Frame & Chassis

Follow chassis manufacturer’s maintenance guide (refer to chassis manual)

Inspect hitch receiver (if towing) 



Tires

Check and adjust air pressure  Check tread wear  Check front end alignment and adjust if needed 

Miscellaneous

Lubricate locks, hinges, and latches 

10-14

Winnebago Trend (2014), Trend 23B (2014), Trend 23L (2014) User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual