Intel® Apollo Lake Pentium N4200
Windows® 10 IoT Enterprise
User Guide
Document Version 1.1
Document Part No. : 9152101K100T
M101P-ME
Please read these instructions carefully before using this product, and save this manual for future use.
Page 2
2
Medical Windows Tablet M101P-ME User Guide
Contents
CHAPTER 1: READ ME FIRST ......................................................................................................................................................4
1.2INTENTION OF USE ........................................................................................................................................................................ 5
1.3SAFETY INFORMATION .................................................................................................................................................................... 6
1.4HANDLING AND MAINTENANCE ........................................................................................................................................................ 9
1.5DECLARATION OF CONFORMITY (DOC) ............................................................................................................................................ 10
2.3DESCRIPTION OF PARTS ................................................................................................................................................................ 14
2.4HOTKEY FOR SPECIFIC FUNCTIONS .................................................................................................................................................. 16
2.5.3 Charging Your Tablet ...................................................................................................................................................... 18
2.5.4 Starting the Tablet .......................................................................................................................................................... 19
CHAPTER 3: SETTING UP WINDOWS ....................................................................................................................................... 20
3.2SETTING UP WINDOWS 10IOTENTERPRISE ..................................................................................................................................... 21
CHAPTER 4: OPERATING THE DEVICE ...................................................................................................................................... 24
4.3USING CAMERA .......................................................................................................................................................................... 27
4.4.1 Using the Wireless LAN (Wi-Fi) ....................................................................................................................................... 28
4.4.2 Using the Wireless WAN (3G/LTE) .................................................................................................................................. 29
4.4.3 Using the GPS ................................................................................................................................................................. 29
4.4.4 Using the Bluetooth ........................................................................................................................................................ 29
4.4.5 Turning On/Off LED Indicators........................................................................................................................................ 30
4.4.6 Using the Barcode Reader .............................................................................................................................................. 30
4.4.7 Using the HF RFID Reader ............................................................................................................................................... 38
4.4.8 Turn on/off the GPS External Antenna ........................................................................................................................... 43
4.4.9 Turn on/off the Light Sensor ........................................................................................................................................... 44
4.5.1 PC Information ................................................................................................................................................................ 46
4.5.2 Battery Information ........................................................................................................................................................ 46
4.5.3 Using the Physical Function Keys (Hotkeys) .................................................................................................................... 47
CHAPTER 5: FREQUENTLY USED SETTINGS .............................................................................................................................. 48
5.1SCREEN RESOLUTION SCALING AND SETTING ..................................................................................................................................... 49
5.6PAIRING WITH A WIRELESS BLUETOOTH BARCODE SCANNER ................................................................................................................ 56
5.6.1 Setup Computer for Bluetooth Pairing ........................................................................................................................... 56
5.6.2 Set up the Barcode Scanner for Bluetooth Pairing ......................................................................................................... 60
5.6.3 Perform Bluetooth Pairing .............................................................................................................................................. 60
APPENDIX A:MEANING OF SYMBOLS ON THE UNIT .................................................................................................................................. 68
APPENDIX C:ORDER INFORMATION ...................................................................................................................................................... 70
Page 4
4
Medical Windows Tablet M101P-ME User Guide
Chapter 1: Read Me First
This chapter provides safety information, handling and maintenance
precautions and other important information about using the M900P
rugged tablet.
Page 5
5
Chapter 1: Read Me First
1.1 Advisory Conventions
Note: A note is used to emphasize helpful information
Important: An important note indicates information that is important for you to know.
Caution: A Caution alert indicates potential damage to hardware and explains how to avoid the potential problem.
Attention : Unealerted’attentionindique un dommage possible à l’équipement et
explique comment éviter le problèmepotentiel.
Warning!
An Electrical Shock Warning indicates the potential harm from electrical hazards and how
to avoid the potential problem.
Avertissement! Un Avertissement de Choc Électriqueindique le potentiel de chocssur
des emplacements électriques et comment évitercesproblèmes.
Important:
This tablet can only use at landscape mode. Do not use at portrait mode.
Cette tablette ne peut être utilisée qu'en mode paysage. Ne pas utiliser en mode portrait.
Four types of advisories are used throughout the user manual to provide helpful information or to alert you
to the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and
Warnings. The following is an example of each type of advisory.
1.2 Intention of Use
This tablet is intended to serve as a display-integrated computing platform for integration with hospital
system. This device is designed for general purpose for hospital environment. For data collection and
display for reference. It shall not be used for life-supporting system.
This Tablet is hand held equipment for health care professionals and can be mounted in a cradle with
VESA mount for fix equipment.
Page 6
6
Medical Windows Tablet M101P-ME User Guide
1.3 Safety Information
Precaution on Battery Pack
Précaution avec le bloc-pile
Do Not Disassemble, Modify, or Insert Sharp
Objects Into the Battery Pack. Electrolyte leakage,
generation of heat, ignition or rupture may result.
[FR] Ne pas démonter, modifier, ou insérer des
objets pointus à l'intérieur du bloc-pile. Une fuite
d'électrolyte, la génération de chaleur, l'amorçage
ou la rupture peuvent être occasionnés.
Do Not Short the Positive (+) and Negative (-)
Terminals of the Battery. Generation of heat,
ignition or rupture may result. When carrying or
storing the device, do not place the battery pack
together with articles that may contact electricity.
[FR] Ne pas court-circuiter les bornes Positive (+)
et Négative (-) de la pile, la génération de chaleur,
l'amorçage ou la rupture peuvent être occasionnés.
Lors du transport et du rangement de l'appareil, ne
pas placer le bloc-pile en même temps que des
articles pouvant créer un contact électrique.
Do Not Apply Shocks to the Battery by Dropping It
or Applying Strong Pressure to It. Electrolyte
leakage, generation of heat, ignition or rupture of
battery may occurs.
[FR] Ne pas faire subir de choc à la pile en la
laissant tomber ou en appliquant une forte pression
dessus. Une fuite d'électrolyte, la génération de
chaleur, l'amorçage ou la rupture peuvent être
occasionnés.
Do Not Charge the Battery Other Than Methods
Those Specified In This Manual. If the battery is not
charged using one of the specified methods,
electrolyte leakage, generation of heat, ignition or
rupture may result.
[FR] Ne pas charger la pile par d'autres méthodes
que celles spécifiées dans ce manuel. Si la pile
n'est pas chargée en utilisant l'une des méthodes
spécifiées, une fuite d'électrolyte, la génération de
chaleur, l'amorçage ou la rupture peuvent être
occasionnés.
When the Battery Pack Has Deteriorated, Replace
It with a New Battery. Continued use of a damaged
battery pack may result in heat generation, ignition
or battery rupture.
[FR] Lorsque la pile est détériorée, la remplacer par
une nouvelle pile. L'utilisation continue d'une pile
endommagée peut occasionner une génération de
chaleur, l'amorçage ou la rupture de la pile.
Do Not Expose the Battery Pack to Excessive Heat,
or Extreme Heat (Near Fire, in Direct Sunlight for
example) Generation of heat, ignition or rupture
may result
[FR] Ne pas exposer le bloc-pile à une Chaleur
Excessive, ou une Chaleur Extrême (Près d'un feu,
sous la lumière du soleil par exemple)Une
production de chaleur, l'amorçage ou la rupture
peuvent être occasionnés
Do Not Use the Battery Pack With Any Other
Products. The battery pack is rechargeable and is
only designed for this specific product. If it is used
with a product other than the specified product,
electrolyte leakage, generation of heat, ignition or
rupture may result.
[FR] Ne pas utiliser avec un autre produit La
batterie est rechargeable et a été conçue pour un
produit spécifique. Si elle est utilisée sur un produit
différent
de celui pour lequel elle a été conçue, des pertes
d’électrolytes et une production de chaleur sont
possibles, elle risque également de prendre feu ou
de casser.
Do Not Use This Product With Battery Other Than
the One Specified.
[FR] Ne pas utiliser ce produit avec une batterie
autre que celle spécifiée
Follow and adhere to all warnings and
instructions in this manual. For your safety,
please read all safety and operating
instructions before using the product. Keep
this manual for future reference.
Page 7
7
Chapter 1: Read Me First
Discontinue using device immediately if you notice
the battery is swelling, or looks puffy or misshapen.
Do not attempt to charge or use the device. Do not
handle a damaged or leaking battery. Do not let
leaking battery fluid come into contact with your
eyes, skin or clothing.
[FR] Si vous remarquez une pile gonflée, élargie ou
anormale, cesser l’utilisation de l’appareil
immédiatement. N’essayez pas de recharger
l’appareil ou de l’utiliser. Ne pas manipuler une pile
qui fuit ou qui est endommagée. Ne laissez pas de
liquide qui fuit entrer en contact avec vos yeux,
votre peau ou vos vêtements.
WARNING: To avoid risk of electric
shock, this equipment must only be
connected to a supply mains with
protective earth.
AVERTISSEMENT: pour éviter tout
risque d'électrocution, cet équipement
ne doit être connecté qu'à un réseau
d'alimentation avec terre de
protection.
Warning! Do not modify this
equipment without authorization of the
manufacturer.
Avertissemen! Ne modifiez pas cet
équipement sans l'autorisation du
fabricant.
Use a soft cloth to clean the surface.
[FR] Utilisez un chiffon doux pour nettoyer la
surface.
Please follow the local national requirement to
dispose unit/accessories/waste products/residues
etc.
[FR] Veuillez suivre l'exigence nationale
d'élimination de l'unité / accessoires / déchets /
résidus, etc.
When you disconnect the AC adapter, disconnect
from the socket-outlet First.
[FR] Lorsque vous déconnectez l'adaptateur
secteur, déconnectez-le de la prise de courant.
The equipment should be installed near an easily
accessible outlet.
For pluggable equipment, the power outlet must be
installed near the equipment and must be easily
accessible.
Accessory equipment connected to the analog and
digital interfaces must be in compliance with the
respective nationally harmonized IEC standards
(i.e. IEC 60601-1 for medical equipment.)
Furthermore all configurations shall comply with the
system standard in IEC 60601-1. Anyone who
connects additional equipment to the signal input
part or signal output part is configuring a medical
system, and is therefore, responsible that the
system complies with the requirements of the
system standard IEC 60601-1. The unit is for
exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC
60950-1 certified equipment outside of the patient
environment.
[FR] L'équipement doit être installé à proximité d'un
point de vente facilement accessible.
Pour les équipements enfichables, la prise de
courant doit être installée à proximité de
l'équipement et doit être facilement accessible.
Les accessoires connectés aux interfaces analogiques et
numériques doivent être conformes aux normes CEI
harmonisées respectives au niveau national (c.-à-d. CEI
60601-1 pour les équipements médicaux). De plus,
toutes les configurations doivent être conformes à la
norme système CEI 60601-1. Quiconque connecte un
équipement supplémentaire à la partie entrée de signal
ou à la partie sortie de signal configure un système
médical et est donc responsable de la conformité du
système aux exigences de la norme système IEC 60601-
1. L'unité est destinée à l'interconnexion exclusive avec
l'équipement certifié CEI 60601-1 dans l'environnement
du patient et à l'équipement certifié CEI 60950-1 en
dehors de l'environnement du patient.
Circuit diagrams, descriptions and component parts
list will be made available only upon request when
servicing is required. Please, contact the address
below for related information.
WINMATE INC, 9TH FL 111-6 SHING-DE RD
SAN-CHUNG TAIPEI HSIEN,241 TAIWAN.
[FR] Les schémas de circuit, les descriptions et la
liste des composants seront disponibles
uniquement sur demande lors de la maintenance.
S'il vous plaît, contactez l'adresse ci-dessous pour
des informations connexes.
WINMATE INC., 9E FL 111-6 SHING-DE RD SANCHUNG TAIPEI HSIEN, 241 TAIWAN.
Page 8
8
Medical Windows Tablet M101P-ME User Guide
General Product Safety
Sécurité générale des
produits
Do not block any ventilation openings. Do not
place the product against a wall or in an enclosed
space as doing so might impede the flow of
cooling air.
[FR] Ne pas bloquer les ouvertures de ventilation.
Ne pas placer le produit contre un mur ou dans un
espace clos de façon à entraver la circulation de
l'air de refroidissement.
Warning! Tablet with cradle cannot
be hand-held operated, and must be
used with VESA mount as a fixed
equipment.
Avertissemen! La tablette avec
socle ne peut pas être utilisée à la
main et doit être utilisée avec un
support VESA comme équipement
fixe.
Do not place the product near any heat sources
such as radiators, warm air intakes, stoves or
other heat-generating devices (including amplifiers
or other heat producing equipment).
[FR] Ne pas placer le produit près d'une source de
chaleur comme des radiateurs, les arrivées d'air
chaud, poêles ou autres produits générant de la
chaleur (y compris les amplificateurs ou autre
équipement produisant de la chaleur.)
Protect the power cord from being crushed or
pinched, particularly in the area of the plugs, any
receptacles used, and the point of exit from the
apparatus. Do not break off the ground pin of the
power cord.
[FR] Empêcher le cordon d'alimentation d'être
écrasé ou pincé, en particulier dans les zones de
prises, des containers utilisés, et du point de
sortie de l'appareil. Ne pas casser la broche de
terre du cordon d'alimentation.
Do not disregard the safety that a polarized or
grounded connection can provide. A polarized
connection consists of two plugs, one of which is
larger than the other. A grounded connection has
two blades and a third one that is grounded. If the
main plug provided cannot be inserted into your
outlet, consult an electrician to replace your
obsolete outlet.
[FR] Ne pas ignorer la sécurité qu'une prise
polarisée ou une prise de terre peut prévoir. Une
prise polarisée se compose de deux fiches, dont
l'une est plus large que l'autre. Une prise de terre
possède deux lames et une troisième qui est la
terre. Si la fiche principale fournie ne peut être
insérée dans votre prise, consultez un électricien
pour remplacer votre prise obsolète.
Use only accessories specified by the
manufacturer.
[FR] Utiliser uniquement les accessoires spécifiés
par le fabricant.
This product should not be used near water such
as bathtubs, sinks, swimming pools, wet
basement, etc.
[FR] Ce produit ne dois pas être utilisé près de
l'eau comme les baignoires, les éviers, les
piscines, les sous-sols humides, etc.
Use only with its transport carriage, stand, tripod,
console or table specified by the manufacturer or
sold with the product. When using a carriage,
move the carriage assembly with the product
carefully to avoid damage from falling over.
[FR] Utiliser uniquement avec son chariot de
transport, support, trépied, console ou table
spécifiés par le fabricant ou vendu avec le produit.
Lors de l'utilisation d'un charriot, déplacez
l'ensemble chariot avec le produit avec soin pour
éviter tout dommage de chute.
Unplug this apparatus during lightning storms or
when it is not being used for long periods.
[FR] Débrancher cet appareil durant les orages ou
lorsqu'il n'est pas utilisé pendant de longues
périodes.
Refer all servicing to qualified service personnel.
A technical intervention is required when the
apparatus has been damaged in any way, for
example if the power cord or plug is damaged,
liquid has been spilled or objects have fallen
inside the unit, if the product has been exposed to
rain or moisture, if it does not operate normally or
if it has been dropped.
[FR] Confier toute réparation à du personnel
qualifié. Une intervention technique est nécessaire
lorsque l'appareil a été endommagé de quelque
façon, par exemple si le cordon d'alimentation ou
la fiche est endommagé, du liquide a été renversé
ou des objets sont tombés à l'intérieur de l'unité, si
le produit a été exposé à la pluie ou à l'humidité,
s'il ne fonctionne pas normalement ou s'il a été
jeté.
• Grounding reliability can only be achieved when
the equipment is connected to an equivalent
receptacle marked “Hospital Only” and “Hospital
Grade”. Use a power cord that matches the
voltage of the power outlet, which has been
approved and complies with the safety standard of
your particular country.
[FR] La fiabilité de la mise à la terre ne peut être
atteinte que lorsque l’équipement est connecté à
un récipient équivalent portant la mention
«Hospital Only» et «Hospital Grade». Utilisez un
cordon d'alimentation correspondant à la tension
de la prise de courant approuvée et conforme aux
normes de sécurité de votre pays.
Page 9
9
Chapter 1: Read Me First
1.4 Handling and Maintenance
General Guideline
Guide Général
Keep the product at least 13 cm (5 inches) away
from electrical appliances that can generate a
strong magnetic field such as TV, refrigerator,
motor, or a large audio speaker.
[FR] Garder le produit au moins à 13 cm (5 pouces)
de distance des appareils électriques qui peuvent
générer un fort champ magnétique comme une
télévision, un réfrigérateur, un moteur, ou un
important haut-parleur.
Do not place heavy objects on top of the tablet
computer as this may damage the display.
[FR] Ne pas placer d'objets lourds sur le dessus de
l'ordinateur tablette cela peut endommager l'écran.
The screen surface can be easily scratched. Use
with care. Do not use paper towels to clean the
display but use the included cleaning cloth. Avoid
touching it with a pen or pencil.
[FR] La surface de l'écran peut être facilement
rayée. Utiliser avec précaution. Ne pas utiliser de
serviette en papier pour nettoyer l'écran mais
utiliser le chiffon de nettoyage inclus. Éviter de
toucher avec un stylo ou un crayon.
To maximize the life of the backlight in the display,
allow backlight to automatically turn off as a result
of power management. Avoid using a screen saver
or other software that prevents the power
management from working.
[FR] Pour maximiser la durée de vie du
rétroéclairage de l'écran, autoriser le rétroéclairage
résultant de la gestion de l'alimentation. Éviter
d'utiliser un économiseur d'écran ou un autre
logiciel empêchant la gestion de l'alimentation de
fonctionner.
Cleaning Guideline
Guide de nettoyage
Use a soft cloth moistened with water or a nonalkaline detergent to wipe the exterior of the
product.
[FR] Utiliser un chiffon doux humidifié avec de l’eau
ou un détergeant non alcalin pour essuyer
l'extérieur du produit.
Gently wipe the display with a soft, lint-free cloth.
Do not use alcohol or detergent on the product.
[FR] Essuyer délicatement l'écran avec un chiffon
doux non pelucheux. Ne pas utiliser d'alcool ou un
détergent sur le produit.
Touchscreen Guideline
Guide de l'écran tactile
Use your finger or the stylus on the display. Using
sharp or metallic object may cause scratches and
damage the display, thereby causing errors.
[FR]Utiliser votre doigt ou le stylet sur l'écran.
L'utilisation d'un objet pointu ou métallique peut
provoquer des rayures.
Use a soft cloth to remove dirt on the display. The
touchscreen surface has a special protective
coating that prevents dirt from sticking to it. Not
using a soft cloth may cause damage to the special
protective coating on the touchscreen surface. To
clean off hard to remove dirt, blow some steam on
the particular area and gently wipe away using a
soft cloth.
[FR]Utiliser un chiffon doux pour enlever la
poussière sur l'écran. La surface de l'écran tactile a
un revêtement protecteur spécial empêchant la
saleté de se coller à lui. Ne pas utiliser un chiffon
doux peut endommager le revêtement spécial sur la
surface de l'écran tactile. Pour nettoyer les saletés
plus difficiles à enlever, souffler de la buée sur la
zone particulière et essuyer doucement avec un
chiffon doux.
Do not use excessive force on the display. Avoid
placing objects on top of the display as this may
cause the glass to break.
[FR]Ne pas utiliser une force excessive sur l'écran.
Éviter de placer des objets au dessus de l’écran
cela pourrait provoquer une cassure du verre.
When there is a noticeable discrepancy in the
operation of the touchscreen function (your touch
does not correlate to the proper location on the
screen), recalibrate the touchscreen display.
[FR]Lorsqu'il y a un écart sensible dans le
fonctionnement de l'écran tactile (votre contact ne
correspond pas à la bonne position sur l'écran),
recalibrer l'écran tactile.
Page 10
10
Medical Windows Tablet M101P-ME User Guide
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference
received including interference that may cause
undesired operation
Medical electrical equipment Part 1-2: General requirements for
basic safety and essential performance - Collateral Standard:
Electromagnetic disturbances
EN 60601-1-2:2015
EN 5511:2019+A1:2010
EN 61000-4-2: 2009
EN 61000-3-2:2014
EN 61000-4-3: 2006+A1: 2008+A2: 2010
EN 61000-3-3:2013
EN 61000-4-4: 2012
EN 61000-4-5: 2006
EN 61000-4-6: 2014+AC:2015
EN 61000-4-8: 2012
EN 61000-4-11: 2004
Medical electrical equipment Part 1: General requirements for
basic safety and essential performance
EN 60601-1:2016/A1:2013/A12:2014
1.5 Declaration of Conformity (DoC)
FCC Statement
This equipment has been tested and found to comply with the limits for a class "B" digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at him own expense.
CE Notice (European Union)
This equipment is in conformity with the requirement of the following EU legislations and
harmonized standards. Product also complies with the Council directions.
1.6 Classification
Supply Class I adapter
No applied part
IP65 (Only for panel)
Continuous Operation
Not AP or APG category
Page 11
11
Chapter 2: Getting Started
Chapter 2: Getting Started
This chapter tells you step by step how to get the Rugged Tablet up and
running.
Page 12
12
Medical Windows Tablet M101P-ME User Guide
2.1 Introduction
Thank you for purchasing 10.1-inch Medical Windows Tablet Computer M101P-ME. M101P-ME is a
medically certified Windows-based tablet computer with a housing enhanced with antimicrobial
properties, weighting at just 1200 grams (2.7 pounds). This mobile and portable device is flexible
enough to function as a standalone device and competent enough to be used for all sorts of data
collection, patient care, information management and wireless communication in medical environments.
With rugged features, a crystal clear 1920 x 1200 resolution display, projected capacitive touch screen,
barcode scanner and superior processing power coming from Intel’s Apollo Lake processor, this tablet
can be used in hospital halls, waiting rooms or nurse stations for communicating and documenting
patient information, allowing paramedics and nurses to instantly access and keep patient records.
Highlights
10.1” 1920 x 1200 IPS LED Panel with direct optical bonding
Intel® Apollo Lake Pentium N4200 processor
Housing enhanced with antimicrobial properties
Long battery life
USB 3.0 (Type C) connector
Optional 1D/2D barcode scanner to scan medications or wrist bands
Lightweight, rugged, IP65 waterproof and dustproof
IEC 60601-1, 60601-1-2 Medically Certified
Page 13
13
Chapter 2: Getting Started
Medical Tablet Computer
Standard Battery
Manufacturer : Winmate Inc.
Model name : BS101
Power Adapter
Manufacturer : EDAC POWER ELECTRONICS CO., LTD.
Model name : EM10683V & EM10681V
Power Cord and Plugs
Manufacturer : PHINO ELECTRIC
(HUIZHOU)LTD.
Model name : PHP-350 TO PHS-301
Capacitive Touch Stylus
Manufacturer : HuntWave Industrial Co., Ltd.
Model name : 3.5mm Plastic pen tip and
5.5mm Rubber stylus
Driver CD
Medical Grade Tablet Dock (Medically Certified)
Desk Dock
Vehicle Dock
Battery Charger
Active Pen
Smart Card Reader
Handstrap
UHF RFID Reader
VESA Mount Kit
Shoulder Strap
Carry Bag
Micro HDMI Cable
Vehicle Charger
Mobile Printer MX20/ MX30
2.2 Unpacking
Check and identify the standard supplied accessories.
Standard factory shipment list:
Optional Accessories
Your package may include optional accessories based on your order.
Page 14
14
Medical Windows Tablet M101P-ME User Guide
Front:
Left: Right:
No
Item
Description
1
10.1” Touch
Screen
Display and act as one of
the inputs for the Tablet
Computer
2
Digital Mic
with noise
cancellation
Use during video
recordings and
communications.
3
Front Camera
2 Megapixel Webcam
4
Light Sensor
and LED
Indicators
Show the current status of
the Tablet Computer. RF
communications, storage,
battery status, power
status.
5
I/O Cover
Protect I/O ports
6
Fn1 Button
Programmable function
key configured by Hottab
Utility
7
Menu Button
Hottab Quick Access
8
Power Button
Power on/off tablet
Front LED Indicator Details:
No
Item
Description
9
Micro HDMI
HDMI output to external
display
10
Clear CMOS
Hardware reset button.
11
MicroSD Card
Reader
Memory card reader
port for MicroSD Card
12
USB 3.0
Type C
High speed USB port
connects to USB
devices, such as USB
flash drive, mouse,
keyboard, printer, etc.
※No ALT Support,
Power Output 5V/0.9A
13
USB 3.0
Type A
USB 3.0 port connects
to USB devices, such
as USB flash drive,
mouse, keyboard,
printer, etc.
14
Mic In/Line Out
Headset or headphone
can be connected (Mic
is only supported with
3.5mm 4-pin headset)
15
Power Jack
DC power input jack.
2.3 Description of Parts
Dimensions: 271.8 x 197.2 x 19 mm
Page 15
15
Chapter 2: Getting Started
Rear:
No
Item
Description
16
Optional RFID
Reader
RFID Reader for reading
RFID tags.
17
Optional
Extension
Port
Provides connectivity to
custom modules for
special applications
(USB2.0 x 1, RS232 x 1).
18
Camera Flash
LED camera flash to
provide flash lighting
when use with camera.
19
Rear Camera
8MP Autofocus Camera.
Captures photos and
videos.
20
Battery
Release
Slider
Spring-loaded slider that
latches the battery in.
21
Touch Pen
Slot
Pen holder slot to store
touch pen
22
Battery Lock
Latch
Latch to lock the battery
in place once battery is
inserted. Not springloaded.
23
Speakers
Emit sounds.
24
3G / LTE
Module / SIM
card slot
Service window to insert
Micro SIM card. Also
provide access to 3G /
LTE Module.
25
Fn2 Button
Programmable function
key configured by Hottab.
26
Brightness or
Volume
Buttons
Brightness/ Volume
Control.
(+) Up,
(-) Down.
27
Battery
7.4V, typ. 5140 mAh Li-
Polymer Battery (2S1P)
7.4V, typ. 10280 mAh Li-
Polymer Battery (2S2P,
optional)
Top:
Bottom:
No
Item
Description
28
Optional
Barcode
Barcode Scanner for
reading of 1D/2D
barcode.
29
Kensington
Lock Port
Provide lock access for
Kensington Lock.
30
Docking
Connector
Port to docking solutions
such as vehicle docking
to provide power and
external antenna
Below is the expansion port and the expansion
port cover.
Caution: This expansion port
cannot be used.
Attention: Ce port d’extension ne peut pas être utilisé.
Page 16
16
Medical Windows Tablet M101P-ME User Guide
2.4 Hotkey for Specific Functions
In POST (before Windows boots up):
Buttons
Keystroke
Fn1
F6 to enter
Recovery Menu
Fn2
Esc to enter
BIOS setup
screen
Up (+)
Up
Down (-)
Down
Menu + Fn1
Enter
Menu + Up (+)
Right
Menu + Down (-)
Left
In Windows:
Buttons
Keystroke
Menu
Hottab Quick Access
Fn1
Default: Web Browser
Fn2
Default: Camera
UP (+)
Up.
Down (-)
Down.
Power
Power ON/ OFF
Up (+) +
Down (-)
Ctrl + Alt + Del
LED Indicators:
Item
Description
Power Indicator
Blue– Tablet is ON
No light– Tablet is OFF
Battery Status
Orange–AC adapter is plugged in and charging
Green–AC adapter is plugged in and battery is full charged
Slow Blinking Orange - Low battery (<10%)
Fast Blinking Orange – Battery is being hot swapped.
No light – Battery is in use and more than 10%
Disk Activity Indicator
Green - Disk Activity
No light - Disk Idling
RF Communication
Green - WiFi/BT/WWAN/GPS ON
No light - WiFi/BT/WWAN/GPS are all OFF
For the physical buttons on the tablet computer, in addition to its dedicated functions detailed in the
previous section, it can also be used to emulate commonly used keyboard key strokes. Under different
scenario, a single physical button or a combination of physical buttons provide different keyboard key
strokes, which are specified below:
2.5 First-Time Operation
To get started:
1. Install SIM card.
2. Install storage card.
3. Install the battery.
4. Charge your tablet.
5. Start the tablet.
6.
Page 17
17
Chapter 2: Getting Started
Tools Needed:
Service Windows
Screw: M2x5, 4 pc
Screwdriver: Philips Type , Size #0 , for
M2 screws, torque: 2.0 ± 0.5 kgf.cm
3G/ LTE Module
Screw: M2x3.5, 1 pc
Screwdriver: Philips Type , Size #0 , for
M2 screws, torque: 2.0 ± 0.5 kgf.cm
❶ Remove four screws and remove the service
window.
❷ Remove the one screw that secures the 3G/ LTE
module. Carefully lift the module up. Do not to damage the connected cables!
❸ Carefully flip and move the 3G/ LTE module and
to the right. Do not disconnect cables!
❹ Insert SIM-Card all the way in. Chip/ contact facing
down.
❺ Use your hand to carefully pull the cable outside
the module card. Re-insert the 3G/LTE module and
fasten one screw.Accurately route the cables. Do
not bend cables! Do not pinch/ squeeze the cable!
❻Re-insert the service window and fasten with the four
screws.
Caution
When re-inserting 3G/LTE module, please pay attention to cable routing. Make sure the
cable module does not get squeezed.
The Tablet Computer supports 3G/LTE data connection and fits a Micro-SIM card.
To install the SIM card:
Page 18
18
Medical Windows Tablet M101P-ME User Guide
2.5.2 Installing Battery
Caution: Use only the AC adapter included with your Tablet Computer. Using other AC
adapters may damage the Tablet Computer and the Battery.
Attention: utilisez uniquement l'adaptateur secteur fourni avec votre tablette.
L'utilisation d'autres adaptateurs secteur peut endommager la tablette et la batterie.
Caution: For users start up the Tablet Computer for the first time with internal battery
power, please make sure the battery is fully charged before using.
Attention: Assurez-vous que la batterie est complètement chargée avant de
commencer à utiliser la tablette PC pour la première fois.
Caution:
For use only Power Supply
EDAC(EM10683V & EM10681V)
Input : 100-240Vac, 50-60Hz, 2.0-1.0A,
Output : 19 VDC 3.78A Max.
Attention:
Pour utilisation uniquement
EDAC (EM10683V & EM10681V)
Entrée: 100-240Vac, 50-60Hz, 2.0-1.0A,
Sortie: 19 VDC 3,78 A Max.
To install the standard battery pack:
1. Disconnect any cords connected to the tablet computer.
2. Turn the tablet over, back facing up.
3. Locate the Battery Lock Latch and push it to the “Unlocked” position.
4. Locate the Battery Release Slider that is spring-loaded. Pull back and hold.
5. Insert the battery with the connector-pins side first, and then lower the battery into the battery
compartment. Continue to hold the Battery Release Slider until the battery is fully inserted.
6. Make sure the battery is completely lowered into the compartment before letting go of the
Battery Release Slider. Battery will be flat against the housing once fully inserted.
To remove the battery pack:
1. Shut down the tablet (or put into sleep mode). Disconnect any cords connected to the computer.
2. Turn the tablet computer over, back facing up.
3. Locate the Battery Lock Latch and push it to the “Unlocked” position.
4. Locate the Battery Release Slider that is spring-loaded. Pull back and hold.
5. Lift the battery out using the opening on the side of battery compartment.
2.5.3 Charging Your Tablet
The M101P-ME Medical Tablet Computer operates either on external AC power or internal battery
power. It is recommended to use AC power when you start up the Tablet for the first time.
Page 19
19
Chapter 2: Getting Started
Item
Battery Operation
Time
Battery Charging
Time
Standard Battery (BS101)
8 Hours
2.5 Hours
High Capacity Battery (BL101)
16 Hours
4.5 Hours
Important: When powering on the device for the first time, please make sure there’s no
interruption during the Windows setting up process, for example, accidentally powering
off. If it happened, please access the recovery menu by pressing Fn1 button on the front
bezel to initiate recovery process.
Note: Do not press the power button repeatedly.
Do not perform the following operations until the Disk Activity Indicator off
Connecting or disconnecting the AC adapter
Pressing the power button
Touching the tablet buttons, screen, or external keyboard/mouse
Note: The computer will forcibly be powered off if the power button is pressed and held
for 6 seconds or longer.
To connect a tablet to AC power:
1. Open I/O protective cover by pulling out the latch.
2. Plug the DC cord of the AC adapter into the power jack of the tablet computer.
3. Plug the AC power cord into the AC adapter.
4. Plug the AC power cord into the electrical outlet.
The battery LED indicator shows different battery states:
Orange - AC adapter is plugged in and battery is charging.
Green - AC adapter is plugged in and battery is fully charged.
Slow Blinking Orange - Low battery level (<10%).
Fast Blinking Orange – Battery is being hot swapped.
No light – Battery is in use and charged (>10%).
2.5.4 Starting the Tablet
Press and hold the power button for 3 seconds until the blue LED power indicator light up.
To power off the Tablet Computer:
1. Make sure you have closed any programs that are open on the Desktop. Start Screen apps
don’t need to be closed.
2. Tap on the Settings charm.
3. Tap on Power.
4. Tap on Shut Down.
5. Wait for the Tablet Computer to power off.
Page 20
20
Medical Windows Tablet M101P-ME User Guide
Chapter 3: Setting Up Windows
This chapter details how to setup the Windows that may be installed on the
tablet for the first time.
Page 21
21
Chapter 3: Setting Up Windows
Caution: Make sure the battery is full charged before starting the tablet computer for
the first time with internal battery power.
3.1 Introduction
The M101P-ME Tablet Computer operates on Windows 10 IoT Enterprise operating system.
Public network: Select this location if you do not recognize all the computers on the network.
(For example, you are in a coffee shop or airport, or you have mobile broadband.) This is a
public network and is not trusted. Select the location where you will most often use the
computer.
3.2 Setting up Windows 10 IoT Enterprise
Follow the steps below to complete the Windows 10 IoT Enterprise setup process.
1. Press the power button to turn on the computer.
2. First, select your country/region, your preferred app language, your preferred keyboard layout,
and your time zone, then tap Next.
Page 22
22
Medical Windows Tablet M101P-ME User Guide
3. On the Here's the legal stuff screen, read through the disclosures, then tap Accept.
4. Windows will then try to connect to network. Tap Skip this step to continue without a wireless
connection as you can then set up the network later.
5. On the Get going fast screen, click Use Express settings for the fastest setup. If you would
like more information, tap Learn more, or if you would like to select your own options, click
Customize settings.
Page 23
23
Chapter 3: Setting Up Windows
6. To create a local account, type your User name, password, and Password hint in the fields
provided, then tap Next.
7. The initial setup screens are complete, and the desktop is displayed.
8. Read any introductory screens describing features of your computer, and tap Next upon
completing each. You are now done with the initial setup process.
Page 24
24
Medical Windows Tablet M101P-ME User Guide
Chapter 4: Operating the Device
This chapter describes how to operate the M101P-ME Tablet Computer,
including camera, Hottab, barcode, RFID, WWAN, WLAN, GPS features.
Page 25
25
Chapter 4: Operating the Device
Note:
Please download the SDK from Winmate Download Center.
>> M101P >> Development Kit or check the Driver CD which is shipped with the tablet.
Please notice that HF RFID reader, Barcode reader, and UHF RFID reader are optional
module, please make sure user have ordered the module before using the SDK.
(Menu) Button on the Front Panel:
Hottab Utility Icon:
4.1 Hottab Introduction
Hottab provides quick access to the tablet’s functions and features, such as setting up shortcuts, using
camera, powering on/off built-in devices, programming function key, and changing power management.
As Windows starts up, Hottab starts and runs in the background. To display the Hottab control utility, press
the (Menu) Button located on the front panel, OR launching the Hottab Utility application.
The main user interface is located on the right side of the screen. There are 4 main menu options:
Shortcuts, Camera, Device ON/OFF, and Settings. Operations and functions on each menu options is
explained in detail in the coming section.
Page 26
26
Medical Windows Tablet M101P-ME User Guide
Icon
Description
Shortcuts
Allows users to configure short cut to quickly access programs with a few tabs.
Camera
Allows users take a picture or record a video. User can also adjust setting related to
camera in this menu option.
Device
ON/OFF
Enables/disables tablet computer’s hardware functions. The configurable functions are
Wi-Fi, WWAN (3G/4G/LTE), GPS, Bluetooth, Camera, LED indicators, Barcode Reader,
RFID Reader, and GPS Antenna routing options.
Settings
Provides users information such as PC Information, Battery status, and also device
settings such as power management setting, and function key mappings.
4.2 Shortcuts
Short Cut Menu:
To store a new shortcut:
1. Open the Hottab utility by press the (Menu) Button located
on the front panel, OR launching the Hottab Utility application.
2. Tap on the Shortcuts button.
3. Tap on button of any empty slot.
4. An on screen file browser will appear.
5. Browse to find the desired application to have shortcut.
6. Click “Open” to save the shortcut.
To remove an saved shortcut:
1. Open the Hottab utility by press the (Menu) Button located
on the front panel, OR launching the Hottab Utility application.
2. Tap on the Shortcuts button.
3. Tap on the button of any saved slot to remove
4. Shortcut will be removed, and once again show “Empty” to
indicate slot is empty.
Tap on the button will hide the Hottab Utility Menu.
Using the Hottab shortcuts:
1. Open the Hottab utility by press the (Menu) Button located
on the front panel, OR launching the Hottab.
2. Tap on the Shortcuts button.
3. Tap on the saved shortcut items to access saved programs.
Set up On-screen Software Shortcuts
Hottab Shortcuts Menu provides an user-friendly interface to configure on-screen software short cuts
and allow users to quickly access programs with a few tabs. The Shortcuts menu offers 8 empty slots to
store user’s desired quick access. Shortcuts can be mapped to any of the executable files (.exe)
installed on the tablet.
Page 27
27
Chapter 4: Operating the Device
Item
Status Color
Description
Camera
Orange
Camera is enabled.
White
Camera is disabled.
Item
Description
Review
Review
Settings
Opens Camera settings page.
Available Settings:
Picture Save: modify/inspect saved location for pictures.
Video Save Folder: modify/inspect saved location for
video recordings.
Picture Quality: Picture compression quality.
Camera Switch
Switch between front camera or rear camera.
Flash Control
Enables/ Disables LED Flash when taking picture.
Video Record
Tap to Start, and press again to stop recording.
Shutter Camera
Camera Shutter Button. Tap to take picture.
Exit
Exits the Camera and hide Hottab Utility.
4.3 Using Camera
This Hottab menu option allows users take a picture or record a video. Before use, make sure the camera
is powered on under Devices ON/OFF menu with the following scenarios.
To open camera interface:
1. Press the (Menu) button located on the front panel to open Hottab or launch the Hottab Utility.
2. Tap on "Device ON/OFF" button to check the built-in devices status.
3. Check the status color of the Camera icon:
4. If the Camera is disabled (white), tap on the Camera icon to enable it (orange).
5. Go back to the Hottab main menu by pressing the (Menu) Button OR click on the back
arrow on top.
6. Tap on the Camera icon to open Camera menu.
Page 28
28
Medical Windows Tablet M101P-ME User Guide
4.4 Built-in Devices On/Off
Item
Status Color
Description
Wi-Fi
Orange
Wi-Fi is enabled.
White
Wi-Fi is disabled.
This section describes how to get a quick access to set-up built-in devices, including turning on/off RF
modules, setting up barcode reader, RFID reader, and expansion modules.
4.4.1 Using the Wireless LAN (Wi-Fi)
To use the wireless LAN (Wi-Fi) feature to connect to the network, perform the following procedure:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the Wi-Fi icon:
4. If the Wi-Fi feature is disabled (white), tap on the Wi-Fi icon to enable it (orange).
5. Click the wireless network connection status icon in the Windows notification area. A list of
available wireless networks is displayed.
6. Double-click a network to connect to it. Provide required authentication information if needed.
7. To check the connection status, observe wireless network connection status icon in the
Windows notification area. The more bars the icon shows, the better the wireless LAN
connection strength is.
8. Now wireless LAN connection is setup, try connection to the network with a internet browser
such as Internet Explorer.
Page 29
29
Chapter 4: Operating the Device
Item
Status Color
Description
WWAN
4G/LTE
Orange
WWAN (3G/4G) is enabled.
White
WWAN (3G/4G) is disabled.
Item
Status Color
Description
GPS
Orange
GPS is enabled.
White
GPS is disabled.
Item
Status Color
Description
BT
Orange
Bluetooth is enabled.
White
Bluetooth is disabled.
4.4.2 Using the Wireless WAN (3G/LTE)
The M101P-ME Medical Tablet Computer supports data connection with 3G/LTE modules and fits MicroSIM card. (Note: 3G/LTE feature is optional). Insert the SIM-Card as described in Ch.2, 2.5.1 Installing
SIM-Card.
To connect to the network using wireless WAN:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the WWAN icon:
4. If the WWAN feature is disabled (white), tap on the WWAN icon to enable it (orange).
5. You can check the wireless WAN connection status through the wireless network connection
status icon in the Windows notification area. The more bars encompassed, the better the signal is.
4.4.3 Using the GPS
To enable the GPS:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the GPS icon:
4. If the GPS feature is disabled (white), tap on the GPS icon to enable it (orange).
5. Now the GPS feature is ready to be used with an application utilizing the GPS.
4.4.4 Using the Bluetooth
To enable the Bluetooth:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the Bluetooth icon:
4. If the Bluetooth feature is disabled (white), tap on the Bluetooth icon to enable it (orange).
5. Click the Bluetooth icon in the Windows notification area. A contextual menu for Bluetooth is
displayed.
Page 30
30
Medical Windows Tablet M101P-ME User Guide
6. To add a device, tap on Add a Bluetooth Device. Windows will search any Bluetooth device
Item
Status Color
Description
Indicator
Orange
LED indicator is enabled.
White
LED indicator is disabled.
Caution: Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure。Attention: L'utilisation de commandes ou de réglages ou l'exécution de procédures
autres que celles spécifiées dans le présent document peut entraîner une exposition
dangereuse aux radiations.
1
Wavelength
630-680nm
2
Beam divergence
2mrad (Horizontal) x
1.3mrad (Vertical)
expressed at 1/e²
(13.5%) intensity level.
3
Pulse duration and repetition rate
(or description of irregular pulse pattern)
1.68mSec.
Irregular pulse.
4
Maximum power or energy output
1mW
Note:
Download the SDK from Winmate Download center.
>> M101P >> Development Kit or check the Driver CD which is shipped with the tablet.
automatically
7. Choose the Bluetooth device to connect and follow onscreen prompt to continue the pair procedure
and use the Bluetooth device.
4.4.5 Turning On/Off LED Indicators
The LED Indicators for Power Status, Battery Status, and RF Communication can be turned on/off from
Hottab menu.
To enable/disable the LED indicators:
1. Open the Hottab utility by pressing the (Menu) Button located on the front, OR launching the
Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the Indicator icon:
4. If the indicator is disabled (white), tap on the Indicator icon to enable it (orange).
4.4.6 Using the Barcode Reader
The 2D/1D Barcode Reader is optional for M101P-ME Tablet PC and is not re-workable by the end user.
To use this feature, please make sure the tablet PC is built-in barcode reader before use.
To enable the Barcode Reader:
1. Open Hottab utility by pressing (Menu) Button located on the front panel or launching Hottab
Utility application.
2. Tap on the Device ON/OFF button.
Page 31
31
Chapter 4: Operating the Device
Item
Status Color
Description
Barcode
Orange
Barcode Reader is enabled. Reading will need to be
triggered manually thru Fn button.
White
Barcode Reader is disabled.
3. Check the status color of the Barcode icon.
4. Open the application where barcode reader will be displaying the scanned barcode.
5. Trigger the barcode reader by pressing Fn2 function key.
Tap Disconnect button to stop the connection with Barcode Reader.
*To recover the connection, please tap on the button again to re-connect with Barcode Reader.
4.4.6.1 Device Configuring and Setting
1.Click on Windows and search for EZConfig-Scanning from the Start menu.
2.Click on EZConfig-Scanning v4_IE and allow the blocked content if browser is blocking the content.
3.Click on “Connected Device” icon and wait for system to discover the device (Honeywell N660X).
Page 32
32
Medical Windows Tablet M101P-ME User Guide
4.Once Honeywell N660X is discovered please click “Configure Device” button as shown.
Page 33
33
Chapter 4: Operating the Device
4.4.6.2 Scanning mode Settings
1. Click on Device Settings under the Input/Output settings section.
2. Select the desire scanning mode from the drop-down menu shown as below.
3. After selecting a desire scanning mode, click on the “Save to Device” on the side bar.
Page 34
34
Medical Windows Tablet M101P-ME User Guide
Scanning
mode
Description
Manual
Trigger
When in manual trigger mode, the scanner scans until a bar code is read, or until
the trigger is released. Two modes are available, Normal and Enhanced. Normal
mode offers good scan speed and the longest working ranges (depth of field).
Enhanced mode will give you the highest possible scan speed but slightly less
range than Normal mode. Enhanced mode is best used when you require a very
fast speed and don’t require a long working range. Default = Manual Triger-Normal.
Presentation
Mode
Presentation Mode uses ambient light and scan engine illumination to detect bar
codes. When in Presentation Mode, the LEDs remain dim until a bar code is
presented to the scan engine, then the aimer turns on and the LEDs turn up to read
the code. If the light level in the room is not high enough, Presentation Mode may
not work properly.
Streaming
Presentation
Mode
When in Streaming Presentation mode, the scan engine’s aimer goes out after a
short time, but the scan illumination remains on all the time to continuously search
for bar codes. Two modes are available, Normal and Enhanced. Normal mode
offers good scan speed and the longest working ranges (depth of field). Enhanced
mode will give you the highest possible scan speed but slightly less range than
Normal mode. Enhanced mode is best used when you require a very fast scan
speed and don’t require a long working range.
Host Notify
Mode
Host Notify Mode bypasses the decoder and notifies the host that there has been a
hardware trigger pull. When in Host Notify Mode, it is up to the host to initiate an
Image Snap and/or an Image Ship command. It is also up to the host to switch to
another trigger mode.
Snap and
Ship Mode
Snap and Ship mode, allows you to bypass the decoder and ship an image directly
to the host. In this mode, an image is taken and shipped upon each trigger pull,
instead of being sent to the decoder. Snap and Ship is useful when you are using
your own decoder.
Page 35
35
Chapter 4: Operating the Device
Symbologies
Default setting
Linear
UPC-A
Enable
UPC-E
Enable
EAN/JAN-8
Enable
EAN/JAN-13
Enable
UPC-E1
Disable
UPC-A/EAN-13 Extended Coupon Code
Disable
GS1 DataBar Omni-Directinal
Enable
GS1 DataBar Limited
Enable
GS1 DataBar Expanded
Enable
Code 39
Enable
Code 128
Enable
ISBT 128
Disable
GS1-128
Enable
Interleaved 2 of 5
Enable
Matrix 2 of 5
Disable
NEC 2/5
Enable
IATA 2/5
Disable
Code 2/5
Disable
Codabar
Enable
Code 93
Enable
Code 11
Disable
MSI
Disable
Telepen
Disable
Trioptic Code
Disable
Postal Code
Disable
Planet Code
Disable
Korea Psot
Disable
China Post
Disable
Australian Post
Disable
2D
Data Matrix
Enable
PDF 417
Enable
Micro PDF 417
Enable
Codablock A
Disable
Codablock F
Disable
Maxicode
Disable
QR Code
Enable
Aztec
Enable
Composite Code
Disable
Han Xin
Disable
4.4.6.2 Setting the 1D/2D Barcode Scanner Symbologies
The barcode scanner is shipped with default settings shown below. If the default setting suits the usage
requirement, setting symbologies is not necessary.
Symbologies Default Settings:
Changing default setting of symbologies or the advanced setting
There are two methods to change the default setting of symbologies or other advanced setting:
Method (1). Click on the Symbologies on the top, then you can change the
symbology to the default setting or make advanced setting by its category. After setting, click on the
“Save to Device” on the side bar.
Method (2). Click on the reset to default button on the side as shown blow:
Page 36
36
Medical Windows Tablet M101P-ME User Guide
※Warning※
1. The reset to default button will change all setting to default.
2. N660X could disconnect with system after clicking the reset to default button.
Setting
If the Disconnection happened please scan barcodes below in the following steps.
Step 1. Frist please scan the USB HID barcode:
Step 2. Then please scan the USB Keyboard barcode:
Step 3. Please run EZConfig-Scanning again by following 4.4.6.1 Device Configuring and
Page 37
37
Chapter 4: Operating the Device
4.4.6.3 Adding a Prefix or Suffix
1. To add a Prefix or Suffix please click on “Data Formatting icon”.
2.Click on Editor button under the Prefix or Suffix section and create Prefix/Suffix value by
typing in the block or select desire characters in the Control chars, Printable chars, and
Extended ASCII. as shown below:
3. When you finish creating Prefix/Suffix, please click on “Save to Device” on the side bar.
Page 38
38
Medical Windows Tablet M101P-ME User Guide
Note:
User can download the SDK from Winmate Download center website
>> M101P >> Development Kit or check the Driver CD which is
shipped with the tablet.
4. For checking the functionality of Prefix/Suffix, please chick on “Scan Data Window” icon on the
top. Then scan a barcode to verify if the Prefix/Suffix appear correctly.
4.4.7 Using the HF RFID Reader
The HF RFID Reader is optional for M101P-ME Tablet PC and is not re-workable by the end user. To use
this feature, please make sure the tablet PC is built-in HF RFID reader before use, or contact our sales
contact window for more details.
To enable the HF RFID Reader feature:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Tap on RFID, and the setting utility will show up as below:
Page 39
39
Chapter 4: Operating the Device
Item
Status Color
Description
RFID
Orange
HF RFID Reader is enabled.
White
HF RFID Reader is disabled.
4. Tap on the ON button.
5. Check the status color of the ON icon is green, and the status color of the RFID icon on the
Hottab menu is orange at the same time.
Page 40
40
Medical Windows Tablet M101P-ME User Guide
4.4.7.1 RFID Trigger Setting
Item
Description
Auto Scan
The default setting for RFID trigger is Auto Scan. Under this setting, the RFID
Reader will always be ready to scan tags.
1. When the RFID tag is detected from RFID antenna, the data will be read
automatically.
2. User can define the RFID scanning frequency from the drop-down menu
shown as below. The frequency can be from 1 second to 9 seconds.
Single Scan
User can also define the RFID Reader scanning as Single Scan. Under this setting,
the RFID Reader will be triggered only when user click on “Send”.
Page 41
41
Chapter 4: Operating the Device
Item
Description
Sound
The Sound check box defines whether a beep sound will come with the data scanning.
Output to
This setting defines the output type of the scanned data. Two options are available:
Keyboard Wedge
Under this setting, the data scanned is sent like keyboard data. The scanned data can
be output directly to the demo area below this window, or user can also open other
utility, such as Office Word or Notepad files, for data input.
Note: notice that the input method should support the scanned character.
User can also tap on the Settings button for further details settings.
Demo Area
4.4.7.2 Settings
Page 42
42
Medical Windows Tablet M101P-ME User Guide
Item
Description
Prefix
User can type in this field to define the characters BEFORE the
data scanned.
Suffix
User can type in this field to define the characters AFTER the
data scanned.
Append Enter
The check box user can defines to append an “Enter” which is
followed by the characters.
Append TAB
The check box user can defines to append an “TAB” which is
followed by the characters.
Regex Filter
Press on “Presets…” button, user can define how many
characters to show after the data scanned.
Replace
User can define specific characters to be replaced with preferred
characters automatically. When the characters defined in Regex Substitution is scanned, the data will be replaced with the one
filled in Replace with.
Reset to default
User can remove all the set up and back to default mode.
SDK
For users following SDK for software porting, the scanned data can also be output with
the format needed.
Page 43
43
Chapter 4: Operating the Device
Item
Description
Select
RFID
Output
Type
The default setting for built-in HF RFID Reader is to Read UID. For some applications,
user might need to read or write further block data; the drop-down menu under this
section can do this change.
Disconne
ct
User can tap on the Disconnect button to stop the connection with built-in HF RFID
reader.
*To recover the connection, please turn off the module from setting UI and then turn
on the module again.
Item
Status Color
Description
GPS Ext.
Antenna
Orange
GPS Ext. Antenna is enabled, and using external
antenna if available
White
GPS Ext. Antenna is disabled, and using built-in
antenna
4.4.7.3 RFID Output Setting
4.4.8 Turn on/off the GPS External Antenna
The vehicle dock of M101P-ME Tablet PC supports external GPS antenna through standard SMA
connector. To work with external GPS antenna, please make sure the tablet PC is well installed to
vehicle dock, and the vehicle dock has connected with external GPS antenna.
When working with vehicle dock connecting to external antenna, user can switch GPS antenna from the
internal one to the external one from Hottab menu.
To enable/disable the GPS Ext. Antenna:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the GPS Ext. Antenna icon:
4. If the GPS Ext. Antenna is disabled (white), tap on the GPS Ext. Antenna icon to enable it
(orange).
Page 44
44
Medical Windows Tablet M101P-ME User Guide
4.4.9 Turn on/off the Light Sensor
Item
Status Color
Description
Light Sensor
Orange
Light Sensor is enabled.
White
Light Sensor is disabled.
Mode
Usage Scenario
Hand/Rain
(Default)
In Hand/Rain mode the touchscreen rejects false inputs from liquid drops. When
the liquid is removed, the touchscreen accepts touch inputs from bare fingertips.
Supports input by:
Active stylus with palm rejection
Rubber tip passive stylus
Bare fingertips
Stylus
In Stylus mode, the touchscreen supports inputs from the fine-tip passive
capacitive stylus (shipped with tablet).
Support input by:
Fine-tip passive stylus with palm rejection
Active stylus with palm rejection
Rubber tip passive stylus
Bare fingertips
Glove
In Glove mode, the touchscreen supports inputs while the user is operating the
touchscreen with gloves on.
Supports input by:
Glove
Rubber tip passive stylus
Bare fingertips
The Light Sensor can be turned on/off from Hottab menu. To enable/disable the Light Sensor, perform
the following procedure:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Device ON/OFF button.
3. Check the status color of the Light Sensor icon:
4.4.10 Changing Touchscreen Modes
The M101P-ME Medical Tablet Computer supports three built-in operating modes for different usage
scenarios:
To change touch mode:
(1) Shortly press Function Key 1 (To define the function key refer to User Manual, Chapter 4).
(2) Press (Menu) button on the front to open HotTab, or launch HotTab Utility application.
Choose “Device ON/OFF, and then click “Touch Set” icon.
Page 45
45
Chapter 4: Operating the Device
1. Open HotTab utility by pressing (Menu)
Button located on the front panel, OR launching
HotTab Utility application.
2. Choose “Device ON/OFF”and then click on
“Touch Set” icon
3. The Touch Mode Select utility will be shown as
below
4. Under the “Touch Mode”, select the desired
touch modes by tapping on the radio button.
5. Here’s also additional Touch related setting to
switch the touchscreen input between mouse
mode with cursor, or with multi-touch mode:
Mouse Mode: Single touch point supported, with
mouse cursor shown.
Multi-touch Mode:The default setting of the touch
screen supports multi-touch mode (up to 10
points)
1. Open HotTab utility by pressing (Menu) Button located on
the front panel, OR launching HotTab Utility application.
2. Tap on the Setting button.
3. Tap on F1 icon.
4. Tap on the Long Press icon.
5. Change the Long Press function to “Touch Mode” as shown
below:
4.4.10.1 Switch via Built-in HotTab Utility
To switch touchscreen mode via the HotTab:
4.4.10.2 Switch via Programmable Function Buttons:
To switch between the different touchscreen modes via the programmable function buttons, make
sure the touchscreen mode switching is set to the programmable function buttons first.
Once the touchscreen mode switching is set to the programmable function button, Long Press on “F1”
function button to cycle through the different touchscreen modes. When touchscreen mode is
switched, an icon will temporarily overlay on the lower center of the screen to indicate current
touchscreen mode:
Page 46
46
Medical Windows Tablet M101P-ME User Guide
This section provides user device information in regards to BIOS
Version, EC Versions, Hottab Versions, OS Versions, as well as
Unit Serial Number, shown in the picture sample.
This section provides user battery Information.
Main Battery:
The main battery icon displays the battery level in percentages (0
to 100%).
Backup Battery: (For M101P-ME)
The backup battery used for battery hot swapping displays its
state in text with the following meanings.
Status
Description
High
Backup battery is fully charged, and can be
used for hot swapping
Medium
Backup battery level is intermediate, but can be
4.5 Settings
This Hottab menu option provides users information such as PC Information, Battery status, and also
device settings such as power management setting, and function key mappings. Perform the following
procedure to access the Hottab Setting menu:
1. Open the Hottab utility by press the (Menu) Button located on the front panel, OR launching
the Hottab Utility application.
2. Tap on the Settings button.
3. Below shows the items listed in Settings Menu.
4.5.1 PC Information
4.5.2 Battery Information
Page 47
47
Chapter 4: Operating the Device
used for hot swapping
Low
Backup battery level is low, and hot swapping is
not recommended.
Battery Charge Time:
The Battery Information also displays estimated time needed to
fully charge the main battery when AC adapter is plugged in.
Meanwhile, the backup battery is charged by the main battery.
The function key mapping menu option allows user to change the
physical function buttons, Fn1 and Fn2. Users can change what
application will be launched with short press or long press of keys.
To configure function key mapping, perform the following:
1. Open the Hottab utility by press the (Menu) Button located
on the front panel, OR launching the Hottab Utility application.
2. Tap on the Setting button.
3. Tap on function key icon for the corresponding key that you
want to change.
4. At top of utility, it will say “Short Press” or “Long Press” to
indicate what type of press is being configured
5. You can switch what type of press you want to configure by
tapping on the “Short Press” or “Long Press” icon at the
bottom of the utility window.
6. Pick from list of preset applications by tapping on the
application icons OR customize which application to execute
using the picker.
Using the Custom picker:
1. Tap the icon to reveal browser window
2. Navigate to the desired executable to map to function key
3. Tap on “Done” to save selection.
To map the function key to another application:
1. Tap on the icon to remove connection to the original
application, and pick again tapping on icon.
Using the physical function keys:
1. While operating the tablet, click on the physical function keys
to activate functions mapped via the setup in this section.
4.5.3 Using the Physical Function Keys (Hotkeys)
Page 48
48
Medical Windows Tablet M101P-ME User Guide
Chapter 5: Frequently Used Settings
This chapter frequently used settings such as changing resolution and
scaling, using recovery wizard, docking connector and D-Sub port
description, also contain basic troubleshooting guide.
Page 49
49
Chapter 5: Frequently Used Settings
Note:
The M101P-ME Medical Tablet computer is shipped with display scaling set at
Larger - 150%. We recommend the users set the scaling to this setting for optimal
text and image viewing.
Before proceeding to change the scaling option, make sure any opened document is
saved and close, and all running applications are closed before proceeding to
change the display scaling, because this procedure requires users to log out of their
account to apply display scaling change.
5.1 Screen Resolution Scaling and Setting
The M101’s 1920 x 1200 high resolution display is perfect for viewing image, video, or other
applications, however, Windows user interface (icons, buttons, and other user interface elements) may
be too small to read and operate at the default Windows settings. By changing the display scaling or
the display resolution setting of the device, you can adjust the size of the text and other items on the
desktop for optimal viewing. Display scaling is the recommended method because it has the effect of
adjusting user interface element without having to move away from the optimal resolution setting at
1920 x 1200. This section will explain how you can adjust the built-in windows display scaling setting
and resolution setting.
5.1.1 Changing Display Scaling (Recommended)
Perform the following to change display scaling setting:
1. Tap and hold anywhere on the desktop for 3 seconds and release to bring up the context menu,
and select “Display settings” option as shown below:
Page 50
50
Medical Windows Tablet M101P-ME User Guide
1. A “Display” Window will show up. Click on the dropdown option under the “Scale and layout”
section and change the scaling option to “150% (Recommended)” or any other desired display
scaling.
5.1.2 Changing Screen Resolution
Alternatively, instead of changing the display scaling setting, user may choose to change the overall
resolution setting to make screen elements bigger.
1. Tap and hold anywhere on the desktop for 3 seconds and release to bring up the context menu,
and select “Display settings” option as shown below:
Page 51
51
Chapter 5: Frequently Used Settings
2. Click on the dropdown option next to “Resolution” and select the desire resolution by tapping on
the scale:
3. Hit “Apply”. A prompt “Display Settings” prompt will show up to ask the user if the applied
resolution is usable.
4. If the new resolution is the desired display setting hit “Keep changes” and continue to next step. If
the new resolution is not desirable, hit “Revert” and select a different resolution to change to, and
start again from step 2.
5. The user may now use the device with the new resolution setting.
Page 52
52
Medical Windows Tablet M101P-ME User Guide
5.2 Replacing Battery
Caution: Charge the built-in back-up battery every two months to keep battery
health and prevent possible issues from battery over-discharge.
Attention: chargez la batterie de secours intégrée tous les deux mois pour
préserver son intégrité et éviter les problèmes de décharge excessive de la batterie.
Warning!
Before starting the recovery process, be sure to backup all user data, as all data will
be lost after the recovery process.
The M101P-ME Tablet supports hot-swap, meaning the tablet doesn’t need to be powered off to
replace the main battery. To support hotswap, there is a backup battery inside the tablet that is charged
together with the main battery. This battery cannot be removed, and requires adequate power for main
battery hot swapping. When the backup battery is fully charged, the tablet can sustain up to 5 minutes
of runtime for battery hot-swapping.
Perform the following to hot swap the batteries:
1. Power on the tablet, open Hottab to check the power level of the Backup battery.
2. If the Backup battery level is “Low”, please charge the tablet with AC Power until the Backup
battery level is “Medium” or “High”, and do not remove the main battery.
3. If the Backup battery level is at “Medium” or “High”, you can remove the main battery.
4. Insert a new fully charged battery into the battery compartment.
5. Pen Hottab to check Main battery level. If the battery level is displayed incorrect, check if the
new removable battery is inserted properly.
6. If the battery level displayed correct, continue using the tablet.
5.3 Using Recovery Wizard to Restore Computer
The M101P-ME Medical Tablet Computer has a dedicate recovery partition stored on the hard drive of
the tablet to enable quick one-key recovery process. This partition occupies about 11GB of the storage
space, and comes built-in to each M101P-ME tablet computer.
To enable quick one-key recovery procedure:
1. Plug-in the AC adapter to the tablet computer. Make sure the tablet computer stays plugged in
to power source during the recovery process.
Page 53
53
Chapter 5: Frequently Used Settings
2. Power on the tablet computer, and when the boot screen shows up, press the Fn1 button
(Recovery Key) on the front bezel OR press F6 when using an external USB keyboard to initiate
the Recovery Wizard.
3. The following screen shows the Recovery Wizard. Click on “Recovery” button to continue.
4. A warning message about data loss will show up. Make sure data is backed up before recovery,
and click on “Yes” to continue.
5. Wait till the recovery process to complete. During the recovery process, a command prompt will
show up to indicate the percent of recovery process.
6. After recovery is completed, please press any key to continue, and the tablet computer will Shut
down automatically.
Page 54
54
Medical Windows Tablet M101P-ME User Guide
Caution: Do not open when the
expansion port is not used
Attention: Ne pas ouvrir lorsque le
port d'extension n'est pas utilisé
19 Pin Docking Connector
Pin No.
Description
Pin No.
Description
1
RF_GND
11
NC
2
DOCK_DET#
12
NC
3
GPS ANT
13
GND
4
RF_GND
14
Power
5
RF_GND
15
USB+
6
NC
16
USB-
7
NC
17
GND
8
DETECT+
18
GND
9
Power
19
DETECT-
10
Power
COM Port
Device
COM 1
RS232 at I/O
COM 2
RS232 of Expansion Port (optional)
COM 3
HF RFID (optional)
COM 4
Bluetooth Auto Pairing
COM 9
GPS
COM 11
RS232 at Docking (optional)
COM 15
Barcode Reader (optional)
COM 20
UHF RFID (optional)
5.4 Docking Connector Pin Definition
The M101P-ME Medical Tablet Computer supports one 19-pin docking connector at the bottom side. The
pin definition is listed as the following table.
5.5 COM Port Definition
The M101P-ME Medical Tablet Computer uses Hottab utility for built-in peripherals control. All the COM
port numbers have been defined in the OS image coming with the package.
For some special applications, user might re-install OS and lose the COM port settings. To make sure the
features works properly with Hottab utility, please follow the procedure below to re-define the COM port
numbers:
Page 55
55
Chapter 5: Frequently Used Settings
1. Go to "Device Manager", right click on the COM number need to be changed, and tap on "Properties"
to open the setting page.
2. Tap on "Port Setting" tab and click on "Advanced" button.
3. Tap on the dropdown list and choose the correct COM Port Number (refer to the COM Port
Definition Table), and click "OK".
Page 56
56
Medical Windows Tablet M101P-ME User Guide
4. Double check "Device Manager" to make sure the COM Port number has been re-defined
successfully, and then restart the system.
5.6 Pairing with a Wireless Bluetooth Barcode Scanner
The computer is affixed with a Bluetooth MAC (Media Access Control) address barcode label that
enables wireless Bluetooth Barcode Scanner to quickly establish Bluetooth connection with the
computer. It is encoded with leading characters to instruct the wireless Bluetooth barcode scanner to
initial Bluetooth Serial Port Profile pairing request.
5.6.1 Setup Computer for Bluetooth Pairing
To start the pairing process, first perform the following steps to ensure the computer is properly setup
for pairing:
1. Locate the Bluetooth icon in the Notification Area
2. Bring up the Contextual Menu by performing long press on the icon with touchscreen or rightclick on the icon with a mouse, and select Open Settings.
Page 57
57
Chapter 5: Frequently Used Settings
3. Once the Bluetooth & other devices Menu appears, click “More Bluetooth options” under
Related settings section as shown below.
Click OK to continue.
Page 58
58
Medical Windows Tablet M101P-ME User Guide
4. go to “Options” tab, and make sure that in the Discovery section, the computer is set to “Allow Bluetooth devices to find this computer”, as shown below:
Click OK to continue.
5. In the Bluetooth Settings menu, go to “COM Ports” tab. COM port has to be setup for the
wireless Bluetooth Barcode Scanner to communicate via the Bluetooth Serial Port Profile. Click
on the “Add…” button.
6. You are in “Add COM Port” window. Choose “Incoming (device initiates the connection)”, and
click “OK”.
.
Page 59
59
Chapter 5: Frequently Used Settings
Important:
Make sure the application stays open while pairing.
7. The computer will automatically assign COM Port to the Bluetooth connection. In the screenshot
below, COM4 is allocated.
Click OK to continue.
8. Next, the user has to configure the application that is used to accept the scanned data from the
wireless Bluetooth Barcode Scanner. The application has to be configured to accept the same
COM Port that has been assigned for the Bluetooth Serial Port Profile in the previous step.
9. Now the computer is ready for pairing process to start.
Page 60
60
Medical Windows Tablet M101P-ME User Guide
5.6.2 Set up the Barcode Scanner for Bluetooth Pairing
Important
The wireless Bluetooth Barcode Scanner has to be configured as Bluetooth Serial Port
Profile Master device to establish connection via Bluetooth MAC address barcode label.
For a more detailed instruction, please refer to the User Guide for the wireless Bluetooth
Barcode Scanner you are using for paring.
Now the Barcode Scanner is ready for pairing process to start.
5.6.3 Perform Bluetooth Pairing
After you finish setting up both the Computer and Barcode Scanner you are ready to start pairing.
1. Open a program that is used for paring.
2. Perform scanning procedures. A Bluetooth notification window pop-up on the right hand side
of the desktop. Left click on the mouse to enter Add a device menu.
3. Locate the Bluetooth icon in the Notification Area.
4. Click Add Bluetooth Device.
5. In Add a Bluetooth Device window, click Next to connect the Barcode Scanner to the
Computer.
Page 61
61
Chapter 5: Frequently Used Settings
In order to ensure that Bluetooth Device is successfully pared to the Computer, follow the steps
below:
1. Locate the Bluetooth icon in the Notification Area. Select Show Bluetooth Devices.
You can access this menu in the Control Panel:
WindowsControl Panel Devices and Printers Bluetooth Devices
2. Make sure your device is connected to the Computer.
Page 62
62
Medical Windows Tablet M101P-ME User Guide
5.7 Basic Troubleshooting
Problem
Solution
The removable battery is not
charging.
Make sure the AC adapter is properly connected, and that
the removable battery is properly inserted.
Nothing appears on the screen.
The tablet computer may be in sleep mode. Press the power
button to wake up the display.
The brightness level may be too low. Increase brightness.
The screen suddenly turns blank
and the power indicator goes off.
Make sure that LED indicator is not powered off in Hottab.
Make sure the AC adapter is properly connected.
If running on battery power, the battery may be depleted,
charge the battery.
Wireless LAN signal quality is
poor.
The tablet computer may be out of range. Move the tablet
computer closer to the access point or another wireless LAN
device associated with it.
Check if your surroundings have interferences, such as
microwave ovens, cordless phones. Move the tablet
computer away from objects causing interference.
I cannot connect to another
wireless LAN device.
Make sure that wireless LAN feature is powered on.
Make sure that the SSID setting is the same for every
wireless LAN device in the network.
Restart the tablet computer
Make sure the IP address or subnet mask setting is correct.
I cannot connect to another
device with Bluetooth.
Make sure that both devices have Bluetooth powered on
(For the Tablet Computer, check Hottab to see if Bluetooth
is powered on).
Make sure that the distance between the two devices is
within 10 meters and there are no walls or large obstructions
between the devices.
Make sure the both devices are powered on and configured
to be discoverable.
Make sure that both devices are compatible.
The GPS application cannot find
my location.
Make sure that GPS is powered on in Hottab.
Make sure that GPS receiver and the location sensor are
enabled in Control Panel.
The tablet computer may be out of coverage area. Move
your tablet computer outdoors or closer to a window.
Check if your surroundings have interferences, such as
microwave ovens, cordless phones. Move the tablet
computer away from objects causing interference.
No sound is produced.
Adjust volume of the tablet computer by pressing on the
volume rocker.
If using an external audio device, make sure that the cable
is properly connected.
I cannot project the tablet
computer display to another
monitor.
Make sure the VGA driver is installed.
Make sure the output setting selected is correct.
Page 63
63
Chapter 5: Frequently Used Settings
Problem
Solution
Barcode scanner does not emit
laser beam and does not seem to
work.
Make sure the Barcode scanner device is enabled in Hottab
utility.
Make sure under Windows, the Barcode Reader is set to
COM 15 port, so that Hottab can trigger the Barcode Reader
hardware.
Barcode Scanner emits laser
beam but does not read barcode
presented to it.
Adjust the distance between barcode scanner of the device
and the barcode being scanned.
Make sure the barcode code type is enabled in the tablet.
To enable/disable a specific barcode code type, go through
the “Barcode Scanner Configuration” section.
I am having GPS accuracy issue.
When utilizing the GPS function, we recommend disabling
the Barcode Reader in Hottab to reduce interference.
RFID scanner does not seem to
work.
Make sure under Windows, the RFID hardware is set to
COM 3 port.
Battery leaking or swollen.
The lithium battery used in this tablet may swell after being
charged/ discharged many times, but there is no problem
regarding safety.
Continued use in such a state may result in the battery
getting jammed, so please stop using the battery, and
purchase a new one.
Page 64
64
Medical Windows Tablet M101P-ME User Guide
Chapter 6: Accessories
This chapter lists available accessories and describes how to install
accessories to M101P-ME medical tablet computer.
Page 65
65
Chapter 6: Accessories
Accessory
Part Number
Description
Standard
Adapter and Power Cord
922D072W19V0
Provides power 100-240VAC to
19VDC@3.42A
Standard Battery
98K000A00095
7.6V, typ. 4200 mAh Li Polymer
Battery (2S2P)
Capacitive Stylus
9B0000000415
Better precision and data input with
fine-tip point
Optional Medically Certified
Medical Grade Tablet Dock
98DT00A00012
Use to mount tablet in a vehicle
Optional Non-Medically Certified
Desk Dock
98DT00A0000G
Use to mount tablet on the desk
Vehicle Dock
98K000A0003L
Use to mount tablet in a vehicle
Battery Charger
98KT00A0000F
Use to charge tablet’s battery
Active Pen
98K000A0007D
Use for data input on a screen
Smart Card Reader
98K000A0003U
Use to read smart cards
Hand Strap
98K000A0003J
Use to make holding and using a
tablet more secure
UHF RFID Reader
98K000A0003J
Use to scan UHF RFID tags
VESA Mount Kit
98K000A0003O
Use to mount a tablet
Shoulder Strap
98K000A0003Q
Use to carry tablet on shoulder
Carry Bag
9B000000003J
Use to carry tablet in the bag
Micro HDMI Cable
9491191190K1
Use to broadcast a screen to
external display
Vehicle Charger
9226065W19V0
Use to charge a tablet from the
vehicle power source
Mobile Printer MX20
9B000000007B
Use to print label or other
documents from tablet computer
Mobile Printer MX30
9B000000007B
Use to print label or other
documents from tablet computer
6.1 Accessories Introduction
The 101P-ME accessories provide a variety of product support capabilities. Table below lists the
accessories available.
Page 66
66
Medical Windows Tablet M101P-ME User Guide
6.2 Installing Vehicle Cradle
Cradle x 1
Quick Start Guide x 1
Cradle Driver CD x 1
Screws(M4-6mm) for VESA mount x 4
Terminal Block Plug x 1
Power Cable (Cigarette Receptacle to
Terminal Block) x 1
Operating Storage and
Transportation
Atmospheric Pressure
700 hPA~1013 hPA
1. RS232 (with 12V / 0.5A)
Use a vehicle cradle to mount a tablet on the vehicle. Follow the instructions below to install M101P-ME
medical tablet on the vehicle cradle.
Highlights:
•Keeps the tablet securely fastened on a moving vehicle
• Anti-theft design with key lockable cradle
• Wide power voltage input (9~36V DC)
• VESA standard for various mounting fixtures
Cradle is supplied with the following accessories
Specifications
2. VGA output (optional)
3. LAN (10/100)
4. USB 2.0 x 2 (with 5V / 0.5A)
5. DC in (Terminal Block)
6. SMA for External GPS Antenna
Driver installation
For the tablet to work with the Cradle, the driver of the Cradle has to be installed first. The
Cradle driver is not pre-installed on the tablet. For a detailed installation guide, please refer
to the CD that is included with the package or visit Winmate Download Center to download
the latest driver: http://www.winmate.com .
Mounting
The Cradle is designed to work with a standard 75mm x 75mm VESA wild range power input
mounting arm or base. Please mount the VESA plate on the back of the wild range power
input mount first before using it with the tablet.
Page 67
67
Chapter 6: Accessories
❶ Align the cradle alignment
fingers on the bottom of the
cradle mount to bottom of the
tablet, and then push down the
tablet in against the cradle mount.
❷Make sure the tablet’s back
is aligned upright against the
wild range power input
mount. Reposition if the
tablet still moves around.
❸Push down the hook until
a click sound is heard to
secure the tablet into the
Cradle mount.
❶Reach for the latch on the back of
the tablet and pull it sideways.
❷The top hook should be
released after the latch is
pulled.
❸Tilt the tablet slightly
forward first, and then pull
the tablet straight up to
remove it.
Display Modes
Description
Mirror Mode (Default)
The main display resolution might be affected by extended monitor.
Follow the scenarios in installation guide to reset the display.
Extend Mode
It is recommended to operate the tablet with keyboard / mouse under
this mode. If touch function is desired, please use the mirror mode.
How to install a tablet on the cradle
How to remove the tablet from the cradle
The Cradle’s input/output expansion functions will only work if power is connected. Provide 19V
input power to the terminal block directly.
External Display Modes (If optional VGA port is equipped)
Note: Display settings are saved automatically for use next time.
Page 68
68
Medical Windows Tablet M101P-ME User Guide
Appendix
Symbol
Description
Symbol
Description
Symbol
Description
This device
complies with the
Medical Device
Directive
93/42/EEC
Indicates this
device is
compliance with
Part 15 of FCC
rules (Class A)
Serial number
This way up
Stacking limit by
number
Direct current
Fragile
Weight
Keep away
from rain
Temperature
limits
Recycling
symbol for
corrugated
cardboard used
for packaging
Consult
operating
instruction for
use.
TUV SUD Mark
Indicates device
is approved
according To
The UL DEMKO
Regulation
General
warning sign
Indicates device
is approved
according To The
VCCI Regulation