Winmate LDS210D, LDS410D, LDS310D User Manual

Download

Page 1

1U Rack LCD Drawer

LDS Series

User Guide

Rev. 2.1

This specification is subject to change without notice. Manufacturer assumes no responsibility

for any Error Contained herein.

Page 2

IMPORTANT SAFETY INSTRUCTIONS

1. Please read these instructions carefully before using the product and save for later reference.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Clean the product with a damp soft cloth. Do not use liquid or aerosol cleaners as it may cause permanent damage to the screen.

4. Do not use this product near water.

5. Do not place this product on an unstable cart, stand, o r table. The product may fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.

7. This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

8. This product is equipped with a 3-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.

9. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.

10. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amp s.

11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

12. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks and will void the warranty. Refer all servicing to qualified service personnel.

13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally when the operating instructions are followed. Adjust only

those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore

the product to normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance, indicating a need for service.

Page 3

Contents

1. Introduction.......................................................................................................................................... 4

1.1. Overview................................................................................................................................... 4

1.2. Major Features.......................................................................................................................... 4

1.3. Outline Drawing ....................................................................................................................... 4

1.4. Notice........................................................................................................................................ 5

1.5. Check List................................................................................................................................. 5

2. Configurations and Installation............................................................................................................ 6

2.1. Configurations .......................................................................................................................... 6

2.2. Installation ................................................................................................................................6

3. LCD OSD Key Definition................................................................................................................... 8

3.1. The Control Key Description.................................................................................................... 8

3.2. LCD OSD SCREEN................................................................................................................. 8

4. KVM (optional)................................................................................................................................. 10

4.1. KVM OSD Control................................................................................................................. 10

4.2. Selection by Hot Key.............................................................................................................. 13

5. Specifications..................................................................................................................................... 14

6. Cleaning the Rack Drawer Monitor................................................................................................... 14

7. Disclaimer.......................................................................................................................................... 15

8. Troubleshooting:................................................................................................................................ 15

9. Appendix:........................................................................................................................................... 16

9.1 Supporting Resolution Modes:................................................................................................ 16

9.2. Limited Warranty.................................................................................................................... 16

Page 4

1. Introduction

1.1. Overview

The LDS series (LDS210D/LDS310D/LDS410D) are a series of compact devices, built-in a 15”, 17” or 19” LCD display, standard keyboard with numerical keypad, and heavy-duty touch pad to eliminate hardware redundancy and to increase cost efficiency. The 1U rack mount is designed to be an ideal solution for saving valuable rack mounting space, while possessing features such as monitor flip up design, adjustable mounting brackets, built-in LCD OSD and an optional centralized control of 8/16 PCs.

1.2. Major Features

Item LDS210D LDS310D LDS410D

TFT Display

15” 17” 19”

OSD Function

Built in OSD Screen Adjustment Function

VGA

15-pin D-sub RGB Analog Input Signal

DVI(optional)

DVI-D

Power Consumption(Watts)

33 38 41

Power Supply

AC 100-240V Universal

Keyboard and Touch Pad

88-key Keyboard and Integrated Touch Pad

Numerical Key Pad

17-key numerical Key Pad

Dimensions

1U compact design, 515mm (D) x484mm (W) x44mm (H)

Operating Temperature

0° to 50° C Operating Temperature

KVM Switch (optional)

OSD controlled 8/16 port KVM switch

1.3. Outline Drawing

Front Side Mounted on Rack-Mount Chassis

Page 5

8 7

Rear Side (1 port)

Rear Side (8 port)

16 15

Rear Side (16 port)

1.4. Notice

1. Do not touch the LCD panel surface with sharp or hard objects.

2. Please ensure the LCD Drawer is securely in place. The surface for placing and fixing the LCD Drawer should be stable and level or mounted into a suitable cabinet.

3. Ensure there is enough ventilation for the LCD Drawer, as well as out of direct sunlight, away from sources of excessive dust, heat, water, moisture, and vibration.

4. Ensure the location of the LCD Drawer is convenient enough for it to connect to its related facilities.

1.5. Check List

Before using this rack monitor, please make sure that all the items listed below are present in your package

z Analog color LCD Drawer z Accessory Box containing:

1. KVM (Keyboard, Video, Mouse) expansion cable ×1

2. Power cable ×1

3. User guide ×1

If any items are missing or damaged, please contact your dealer immediately.

Page 6

2. Configurations and Installation

2.1. Configurations

The LDS serials rack LCD drawer supports 1 computer. The configuration is as shown in following figure.

2.2. Installation

Step 1. Mount on Rack-Mount Chassis

Mount the Rack Drawer LCD on Rack-Mount Chassis with screws.

STEP1

Step 2. Power Cable Connection

Connect the power cord to the rack LCD monitor and AC outlet.

Step 3. PS2 Mouse, Keyboard and VGA Cable Connection LDS210/310/410 – 1P:

◆ Power down the computer which will be connected to your rack LCD monitor. Plug one end of the KVM expansion cable to the connectors at the rear of the PC system and the other end to the rack LCD monitor.

Cable Appearance

◆ Secure the connectors with the screws on the cable connector at both

Page 7

ends.

LDS210/310/410 – 8/16P:

◆ Power down all computers which will be connected to your rack LCD monitor.

◆ Plug one end of the KVM expansion cable to the connectors at the rear of all the PC

systems and the other end to the rack LCD monitor.

◆ Secure the connectors with the screws on the cable connector at both ends Note: The KVM expansion cable for the LDS210/ 310/ 410 -16P is different from the other KVM switch cables. The end of the KVM switch side is the 15-pin black connector for monitor, keyboard and mouse. The matching port of the KVM switch also uses 15 –pin black ports. Note: All connectors are color coded; blue – video, green – mouse, purple – keyboard

ONE OF YOUR COMPUTER

Cable Appearance

LDS210/310/410-8P

ONE OF YOUR COMPUTER

Cable Appearance

LDS210/310/410-16P

Page 8

3. LCD OSD Key Definition

1. MENU

Use this key to select the function you would like to adjust.

2. ADJUST

Use this key to adjust the selected function for optimal viewing.

3. POWER SWITCH

Use the power switch to turn the power ON or OFF. We recommend turning your PC system power on first, then the LCD monitor.

4. POWER STAND-BY MODE LED

Indicates when the power is in the stand-by mode.

5. Power on LED Indicates when the power is in the ON position.

3.1. The Control Key Description

: Power on/off control. : Call menu / Shifting the selection left.

: Call menu / Shifting the selection right.

- : Decrease value.

+ : Increase value. / Automatic adjustment.

3.2. LCD OSD SCREEN

+ 100

1024x768 H:60.09KHz V:75.12Hz

BRIGHTNESS

Press "+" to increase or "-" to decrease the brightness.

CONTRAST

Press "+" to increase or "-" to decrease the contrast.

H-POSITION

Press "+" or "-" to move the image to the left or right on the screen.

Page 9

V-POSITION

Press "+" or "-" to move the image up or down on the screen.

H-SCALING

Press "+" or "-" to increase or decrease the Horizontal screen size.

AUTO ADJUSTMENT

Press "+" or "-" to have the monitor logic choose the best settings for the current input signal.

WHITE BALANCE

Press "+" or "-" to enable auto adjust white balance function.

COLOR TEMPERATURE

Press "+" or "-" to set the color temperature USER: Use this function to set a proper color temperature.

z 9300K:Push to set monitor for the CIE coordinate 9300 color temperature z 6500K:Push to set monitor for the CIE coordinate 6500 color temperature z 5500K:Push to set monitor for the CIE coordinate 5500 color temperature

GAMMA

Press "+" or "-" to adjust GAMMA Functi on.

PHASE

Press "+" or "-" button to adjust the Phase control. Phase adjustment may be required to optimize the display quality.

OSD TRANSPARENT

Press "+" or "-" to adjust the OSD background color.

ADC ADJUST

Press "+" or "-" to enter the ADC control manual for Brightness, Cont rast, Red Color Gain, Green Color Gain and Blue Color Gain adjustment.

CHANNEL

Press "+" or "-" to change the input channel

RECALL

Press "+" or "-" to RECALL the factory default settings.

OSD EXIT

Press "+" or "-" to EXIT the OSD MENU.

Summary

BRIGHTNESS: Press "+" or "-" to adjust.

CONTRAST: Press "+" or "-" to adjust.

H-POSITION: Move the screen to the left or right side.

V-POSITION: Move the screen up or down.

CLOCK: To adjust the Horizontal screen size.

AUTO: To find the optimal screen settings.

WHITE BALANCE: White Balance value adjust.

COLOR TEMPERATURE: Color Temperature settings.

GAMMA: Gamma value adjust.

PHASE: Adjust horizontal phase for optimal display quality.

TRANSPARENT: OSD Transparent adjustment.

ADC CONTROL: Color degree adjustment.

CHANNEL: change the input channel

Page 10

RECALL: Press "+" or "-" to reset the factory default settings.

EXIT: To exit from the OSD function.

4. KVM (optional)

The 1U Rack LCD Drawer build-in KVM Switch enables a single keyboard, video monitor and mouse to control multiple computers at a time. This product supports one console and 8/16 computer ports. Product model number as follow table:

P/N

LCD Size

Computer port number

LDS210D-8P 15” 8 LDS310D-8P 17” 8 LDS410D-8P 19” 8 LDS210D-16P 15” 16 LDS310D-16P 17” 16 LDS410D-16P 19” 16

This series KVM switch has an On-screen Display (OSD) menu so that you can operate the system easily.

4.1. KVM OSD Control

4.1.1. OSD Window

Press the Left Ctrl key twice to open this window, Press Esc to exit.

OSD MENU

ADDR POWER NAME

Channel Address

Power Indicator

Channel Name

OSD MENU

ADDR POWER NAME

Channel Address

Power Indicator

Channel Name

Field of Title: = = OSD MENU = =

Page 11

Field of Content: ADDR --- To show channel address

POWER --- To indicate power status of computer

Name --- To display computer name

Field of Command: To edit name, press F1

To active Scan, press F2 To set System, press F3 To exit OSD, press ESC To accept Command, press ENTER

Highlight Bar: Use your up and down arrow keys to move the highlight bar, and press

Enter to accept the change.

4.1.2. Characters Accepted by OSD Menu

a-z, A-Z 0-9

- = / ,。; SPACE

Note: the menu displays all letters in capital letter. Only the keyboard can be used in the OSD menu.

4.1.3. Command Menu

Once you have activated the main OSD Window, you can open the Command Menu by press F1 and F3 keys.

4.1.4. Select Channel

--- Open OSD window

--- Use your up and down arrow keys to move the highlight bar to the selected channel

--- Press Enter to accept the change

--- Press ESC to exit and discard changes

4.1.5. Name Channel

Once you have activated the main OSD Window, you can name your channel by press F1.

--- Open OSD window

--- Move up and down arrow key to highlight the channel you wish to change

--- Press F1

Page 12

--- Enter the channel name by using a-z, A-Z, 0-9, =-/, . ; SPACE

--- Delete the letter by using Backspace

--- Press Enter to accept or press ESC to exit without saving

--- Press ESC to exit

4.1.6. Reset keyboard and Mouse

--- Open OSD window

--- Press F3

--- Move up and down arrow key to highlight the channel of RESET KEYBOARD AND MOUSE

--- Press Enter

4.1.7. Set Scan Rate

--- Open OSD window

--- Press F3

--- Move up and down arrow key to highlight the channel of SCAN DELAY TIME

--- Press Enter

--- Enter the scan rate（0-255 seconds）

--- Delete the letter by using Backspace

--- Press Enter to accept or press ESC to exit without saving

--- Press ESC to exit

4.1.8. Active Scan Function

--- Open OSD window

--- Press F3

--- Press ESC to exit

Note: the KVM switch will skip the power-off computers or channels.

If your system is in secure mode, this function will be deactivated.

4.1.9. Memory Function

If you want to know the status of the connected computers or channels, just open the OSD window, and the position of highlighted bar will show you the current computer or channel.

Page 13

Note: this function is only available when using OSD to select computers or channels.

4.1.10. Set Password

Note: This function is only used if you are running your system in secure mode, if you have

forgotten your password; please return this device to the manufacturer.

Only LDS210/310/410-8P offer this function.

--- Open OSD window

--- Press F3

--- Move up and down arrow key to highlight the channel of SET PASSWORD

--- Press Enter

--- Move up and down arrow key to highlight the channel you want to set

--- Press Enter

--- Enter the password

--- Press Enter

--- Enter the new password again

--- Press Enter

When the user password is set, you can only use the ESC key to enter OSD window; you can enter the channel number if password has not been set.

Note: If your system is in secure mode, selection by the push button and hot key will not work.

4.2. Selection by Hot Key

Hot Key combination enables you to select a channel easily. Operation:

Ctrl + Shift +（A-----H）+ Enter

Example:

Ctrl + Shift + B + Enter This is to select computer 2(computer B)

Note: Pls. use the left ctrl and shift keys.

If your system is in secure mode, this function will be deactivated.

Note: “Ctrl+Shift+A+Enter” means to press the left Ctrl key, then the Left Shift key, then A key, and then press Enter key.

Note: If your system is in secure mode, this function will be deactivated.

Page 14

5. Specifications

Item LDS210D LDS310D LDS410D

Display Area(mm)

304.1(H) x 228.1(V) (15-inch diagonal)

337.9(H) x 270.3(V) (17-inch diagonal)

376.3(H) x 301.1(V) (19-inch diagonal)

Pixel Pitch

0.297(H) x 0.297(V) 0.264(H) x 0.264(V) 0.294(H) x 0. 294(V)

Number of Pixels

1024(H) x 768(V) 1280(H) x 1024(V) 1280(H) x 1024(V)

Contrast Ratio

350:1 400:1 600:1

Display Color

16.2M colors 16.7M colors 16.7M colors

Brightness (CD/m^2)

250 280 250

Backlight Unit

2 replaceable CCFLs edge-light (top/bottom)

4 replaceable CCFLs edge-light (top/bottom)

Viewing Angle

-65º~65º(H),

-50º~55º(V)(Typ.)

-70º~70º(H),

-60º~60º(V) (Typ.)

-85º~85º(H),

-85º~85º(V) (Typ.)

I/O

Power: 12V DC Adapter Keyboard:PS/2 Mouse:PS/2 VGA:15-pin D-sub

Keyboard and Key pad

88-key keyboard and integrated Touch Pad 17-key numerical key pad

Power Consumption

33 Watts 38 Watts 41 Watts

Power Supply

AC 100-240V Universal

On-Screen Display

Contrast, Brightness, H/V Position, H/V Size, H-scaling, Auto-adjust, Color Temp.(9300, 6500, User), Red-Gain, Blue-Gain, Green-Gain, Gamma, Recall, Phase, OSD & Exit

Hot Key Control

OSD Hot Key

Environmental consideration

Operating temperature:0ºC~ 50ºC (32 F~ 122 F) Storage temperature:-20ºC~ 60ºC(-4 F~ 140 F)

Humidity

10~85% in operating; 10-90% in storage

Size

515mm(D) x 484mm(W) x 44mm(H)

6. Cleaning the Rack Drawer Monitor

z Make sure the rack drawer monitor is turned off. z Never spray or pour any liquid directly onto the screen or case. z Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles. z The display area is highly prone to scratching. Do not use ketene type material (ex.

Acetone), Ethyl alcohol, toluene, ethyl acid or Methyl chloride to clear the panel. It might permanently damage the panel.

z If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner

onto a clean, soft, lint-free cloth, and wipe the screen

z Don't let water or oil penetrate the monitor. If the droplets are kept for a long time,

Staining and discoloration may occur.

Page 15

7. Disclaimer

We do not recommend the use of any ammonia or alcohol-based cleaners on the monitor screen or case. Some chemical cleaners have been reported to damage the screen and/or case of the rack LCD monitor. Seller will not be liable for damage resulting from use of any ammonia or alcohol-based cleaner.

8. Troubleshooting:

Ensure that all cables are well seated. Check that keyboard/mouse cables are not swapped. If your monitor fails to operate correctly, consult the following chart for possible solution before calling for repairs:

Condition Check Point

1. The picture does not

appear

z Check if the signal cable is firmly seated in the socket. z Check if the Power is ON at the computer z Check if the brightness control is at the appropriate

position, not at the minimum.

2. The screen is not

synchronized

z Check if the signal cable is firmly seated in the socket. z Check if the output level matches the input level of your

computer.

z Make sure the signal timings of the computer system are

within the specification of the monitor.

z If your computer was working with a CRT monitor, you

should check the current signal timing and turn off your computer before you connect the VGA Cable to this monitor.

3. The position of the screen

is not in the center

z Adjust the H-position, and V-position, or Perform the Auto

adjustment.

4. The screen is too bright

(too dark).

z Check if the brightness or contrast control is at the

appropriate position, not at the Maximum (Minimum).

5. The screen is shaking or

waving

z Press ”+” (the Auto - adjustment control) to adjust.

Moving all of objects which emit a magnetic field such as motor or transformer, away from the monitor. Check if the specific voltage is applied.

z Check if the signal timing of the computer system is within

the specification of monitor.

6. Mouse or Keyboard is not

functioning

(for LDS 210/310/410-8/16P)

z Verify that the mouse or keyboard is correctly plugged in to

the KVM switch.

z Verify that the cable is correctly connected between the

computer and the KVM switch.

z Try the keyboard and mouse reset command from the

OSD F3 command menu.

z Restart the computers. z Verify that the keyboard or mouse works when connected

directly to the computer.

Note: The mouse will be inactive when OSD menu is active.

Page 16

7. Hotkey selection is not

functioning

z The Hotkey or Push button selection is inactive when the

password is active.

If you are unable to correct the fault by using this chart, stop using your monitor and contact your distributor or dealer for further assistance.

9. Appendix:

9.1 Supporting Resolution Modes:

LDS210D(15”): LDS310D(17”)/LDS410D(19”):

Mode Resolution H-Freq. (KHz) V-Freq. (KHz)

Mode 1 640×350

31.5

Mode 2 640×400

31.5

Mode 3 640×480

31.5

Mode 4 640×480

37.9

Mode 5 640×480

37.5

Mode 6 720×400

31.5

Mode 7 800×600

35.1

Mode 8 800×600

37.9

Mode 9 800×600

48.1

Mode 10 800×600

46.9

Mode 11 1024×768

48.4

Mode 12 1024×768

56.5

Mode 13 1024×768

60.0

Mode Resolution H-Freq.(KHz) V-Freq.(KHz)

Mode 1 640×350

31.5

Mode 2 640×400

31.5

Mode 3 640×480

31.5

Mode 4 640×480

37.9

Mode 5 640×480

37.5

Mode 6 720×400

31.47

Mode 7 800×600

35.1

Mode 8 800×600

37.9

Mode 9 800×600

48.1

Mode 10 800×600

46.9

Mode 11 1024×768

48.4

Mode 12 1024×768

56.5

Mode 13 1024×768

60.0

Mode 14 1280×1024

64.0

Mode 15 1280×1024 80.0 75

9.2. Limited Warranty

In no event shall the direct vender’s liability for direct or indirect, special, incidental or consequential damages, loss of profit, loss of business, or financial loss which may be caused by the use of the product exceeds the price paid for the product.

The direct vendor makes no warranty or representation, expressed or implied with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.

The direct vendor also reserves the right to revise or update the product or documentation without obligation to notify any user of such revisions or updates. For further information, please contact your direct vendor.

All the brand names and registered trademarks are the property of their respective owners.