Winmate G-WIN User Manual

Page 1
G-WIN Panel PC
Intel® Celeron® N2930 1.83 GHz
Vehicle Mount
User Guide
Document Part Number: 9152111I101J
Page 2
ii
G-WIN Vehicle Mount Panel PC
Preface
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for the use of the described product(s) conveys no license or title under any patent, copyright, or masks work rights to these products, and make no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. We make no representation or guarantee that such application will be suitable for the specified use without further testing or modification.
Warranty
Our warranty guarantees that each of its products will be free from material and workmanship defects for a period of one year from the invoice date. If the customer discovers a defect, we will, at his/her option, repair or replace the defective product at no charge to the customer, provide it is returned during the warranty period of one year, with transportation charges prepaid. The returned product must be properly packaged in its original packaging to obtain warranty service. If the serial number and the product shipping data differ by over 30 days, the in-warranty service will be made according to the shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for November and C for December). For example, the serial number 1W14Axxxxxxxx means October of year 2014.
Page 3
G-WIN Vehicle Mount Panel PC
iii
Customer Service
We provide a service guide for any problem by the following steps: First, visit the website of our distributor to find the update information about the product. Second, contact with your distributor, sales representative, or our customer service center for technical support if you need additional assistance. You may need the following information ready before you call:
Product serial number Software (OS, version, application software, etc.) Description of complete problem The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products.
Page 4
iv
G-WIN Vehicle Mount Panel PC
Advisory Conventions
NOTE:
A note is used to emphasize helpful information
IMPORTANT:
An important note indicates information that is important for you to know.
CAUTION/ ATTENTION
A Caution alert indicates potential damage to hardware and explains how to avoid the potential problem.
Une alerte d’attention indique un dommage possible à l’équipement et explique
comment éviter le problème potentiel.
WARNING!/ AVERTISSEMENT! An Electrical Shock Warning indicates the potential harm from electrical hazards and how to avoid the potential problem. Un Avertissement de Choc Électrique indique le potentiel de chocs sur des emplacements électriques et comment éviter ces problèmes.
ALTERNATING CURRENT / MISE À LE TERRE! The Protective Conductor Terminal (Earth Ground) symbol indicates the potential risk of serious electrical shock due to improper grounding. Le symbole de Mise à Terre indique le risqué potential de choc électrique grave à la terre incorrecte.
Four types of advisories are used throughout the user manual to provide helpful information or to alert you to the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and Warnings. The following is an example of each type of advisory.
Page 5
G-WIN Vehicle Mount Panel PC
v
Safety Information
WARNING! / AVERTISSEMENT!
Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis.
Toujours débrancher le cordon d’alimentation du chassis lorsque vous
travaillez sur celui-ci. Ne pas brancher de connections lorsque l’alimentation est présente. Des composantes électroniques sensibles peuvent être endommagées par des sauts d’alimentation. Seulement du personnel expérimenté devrait ouvrir ces chassis.
CAUTION/ATTENTION Always ground yourself to remove any static charge before touching the CPU
card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis. Toujours verifier votre mise à la terre afin d’éliminer toute charge statique avant de toucher la carte CPU. Les équipements électroniques moderns sont
très sensibles aux décharges d’électricité statique. Toujours utiliser un
bracelet de mise à la terre comme précaution. Placer toutes les composantes électroniques sur une surface conçue pour dissiper les charge, ou dans un sac anti-statique lorsqu’elles ne sont pas dans le chassis.
Page 6
vi
G-WIN Vehicle Mount Panel PC
Safety Precautions
CAUTION/ATTENTION
Do not cover the openings! Ne pas couvrir les ouvertures!
CAUTION/ATTENTION Use the recommended mounting apparatus to avoid risk of injury.
Utiliser l’appareil de fixation recommandé pour éliminer le risque de
blessure.
WARNING! / AVERTISSEMENT! Only use the connection cords that come with the product. When in doubt, please contact the manufacturer. Utiliser seulement les cordons d’alimentation fournis avec le produit. Si vous doutez de leur provenance, contactez le manufacturier.
WARNING!/ AVERTISSEMENT! Always ground yourself against electrostatic damage to the device.
Toujours vérifier votre mise à la terre afin que l’équipement ne se
décharge pas sur vous.
For your safety carefully read all the safety instructions before using the device. All cautions and warnings on the equipment should be noted. Keep this user manual for future reference.
*Let service personnel to check the equipment in case any of the following problems appear:
o The power cord or plug is damaged. o Liquid has penetrated into the equipment. o The equipment has been exposed to moisture. o The equipment does not work well or you cannot get it to work according
to the user manual.
o The equipment has been dropped and damaged. o The equipment has obvious signs of breakage.
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the equipment.
Page 7
G-WIN Vehicle Mount Panel PC
vii
Important Information
Countries/ Area
Symbol
This equipment complies with essential requirements of:
European Union
Electromagnetic Compatibility Directive(2014/30/EU) Low Voltage Directive (2014/35/EU) Restrictions of the use of certain hazardous substances
(RoHS) Directive (2011/65/EU)
USA
FCC Part 1FCC Part 15 Subpart B Regulations Class B
This device complies with part 15 FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received including
interference that may cause undesired operation.
Federal Communications Commission Radio Frequency Interface Statement
This equipment has been tested and found to comply with the limits for a class "B" digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at him own expense.
Page 8
viii
G-WIN Vehicle Mount Panel PC
EC Declaration of Conformity
This equipment is in conformity with the requirement of the following EU legislations and harmonized standards. Product also complies with the Council directions.
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010/ A1: 2015
o IEC61000-4-2: 2009 o IEC61000-4-3: 2006+A1: 2007+A2: 2010 o IEC61000-4-4: 2012 o IEC61000-4-5: 2014 o IEC61000-4-6: 2014 o IEC61000-4-8: 2010 o IEC61000-4-11: 2004
EN55032: 2012/AC:2013 EN61000-3-2:2014 EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013
Page 9
G-WIN Vehicle Mount Panel PC
ix
About This User Manual
NOTE:
Some pictures in this guide are samples and can differ from actual product.
Version
Date
Note
1.0
23-Dec-2016
Initial document release
1.1
20-Jul-2019
Revise specifications
This User Manual provides information about using the Winmate® G-WIN Vehicle Mount Panel PC. This User Manual applies to the G-WIN Vehicle Mount Panel PC – R08IB3S-VMU1, R10IB3S-VMT2, R10IB3S-VMP3, R10IB3S-VMP1, W12IB3S-VMM9 and R15IB3S-VMA3 (HB).
The documentation set for the G-WIN Vehicle Mount Panel PC with Intel® Celeron N2930 1.83 GHz (Bay Trail) processor provides information for specific user needs, and includes:
G-WIN Vehicle Mount Panel PC User Manual – contains detailed description on how to use
the Panel PC, its components and features.
G-WIN Vehicle Mount Panel PC Quick Start Guide - contains detailed description on how to
use the Panel PC, its components and features.
Document Revision History
Page 10
x
G-WIN Vehicle Mount Panel PC
Contents
Preface ........................................................................................................................................ ii
About This User Manual .............................................................................................................. ix
Chapter 1: Introduction .............................................................................................................. 13
1.1 Product Features ................................................................................................................ 13
1.2 Package Content ................................................................................................................ 14
1.3 Mechanical Concept........................................................................................................... 15
1.4 Physical Button and LED Indicators ................................................................................... 16
1.4.1 G-WIN Panel PC 8.4”, 10.4” and 12.1” .................................................................... 16
1.4.2 G-WIN Panel PC 15” ................................................................................................ 17
Chapter 2: Getting Started ......................................................................................................... 20
2.1 Powering On ....................................................................................................................... 20
2.1.1 AC Adapter Components ......................................................................................... 20
2.1.2 Power Considerations ............................................................................................. 21
2.1.3 Connecting the Power ............................................................................................. 22
2.2 Turning On and Off ............................................................................................................ 24
2.3 Installing Operating System ............................................................................................... 25
2.4 How to Enable Watchdog .................................................................................................. 25
2.5 Connectors ......................................................................................................................... 28
2.5.1 Wiring Requirements .............................................................................................. 28
2.5.2 Connector Placement .............................................................................................. 29
2.5.3 Connector Description............................................................................................. 31
Chapter 3: Mounting Solutions ................................................................................................... 35
3.1 Cable Mounting Considerations ........................................................................................ 35
3.2 Safety Precautions ............................................................................................................. 35
3.3 Mounting Guide ................................................................................................................. 36
3.3.1 VESA Mounting ........................................................................................................ 36
3.3.2 Yoke Mounting ........................................................................................................ 38
3.3.3 Roof Mounting......................................................................................................... 41
Chapter 4: Maintenance ............................................................................................................. 45
4.1 Cleaning the Display Screen ............................................................................................... 45
Page 11
G-WIN Vehicle Mount Panel PC
xi
4.2 Cleaning the Casing ............................................................................................................ 45
Chapter 5: Driver Installation ..................................................................................................... 47
5.1 ELO AccuTouch/ CarrollTouch Infrared Driver Installation ............................................... 48
5.1.1 Downloading Drivers ............................................................................................... 48
5.1.2 Configuration Utility ................................................................................................ 49
5.2 The Premier Touch Driver Installation ............................................................................... 51
5.2.1 Installing Touch Kit .................................................................................................. 51
5.2.2 Configuration Utility ................................................................................................ 52
Chapter 6: Troubleshooting ........................................................................................................ 55
6.1 Using USB-HDD or USB-CDROM for Booting OS ................................................................ 55
6.2 Using Recovery Wizard to Restore Computer ................................................................... 57
Chapter 7: Technical Support ..................................................................................................... 60
7.1 Software Developer Support ............................................................................................. 60
7.2 Problem Report Form ........................................................................................................ 61
Appendix A: Panel PC Selection Guide ........................................................................................ 63
A1 Panel PC Selection Guide .................................................................................................... 63
Appendix B: Motherboard Specifications .................................................................................... 65
B1 Intel IB32 (Intel Atom SoC Based) ....................................................................................... 65
Appendix C: Touchscreen ........................................................................................................... 68
C1 Overview ............................................................................................................................. 68
C2 Recommended Touch Interface ......................................................................................... 68
Page 12
12
G-WIN Vehicle Mount Panel PC
Introduction
This chapter gives you product overview, describes features and hardware specification. You will find all accessories that come with the Panel PC in the packing list.
Page 13
User Manual Chapter 1 Introduction
G-WIN Vehicle Mount Panel PC
13
Chapter 1: Introduction
Congratulations on purchasing Winmate® G-WIN Vehicle Mount Panel PC. Winmate® G­WIN Vehicle Mount Panel PC comes with fanless, low power but high performance platform design, sunlight readable panel, WLAN integration, great ability for anti-shock & vibration, IP65 protection and anti-corrosion coating with aluminum alloy housing.
Both of great mobility and robust design are fitting the demands for every harsh environment applications such as logistics, transportation/ fleet management, heavy vehicles, utility and also outdoor usage.
1.1 Product Features
Winmate® G-WIN Vehicle Mount Panel PCs offers the following features:
IP65-proof enclosures (Except I/O parts) for 8.4", 10.4", 12.1", and 15" Totally sealed IP67 Design for 15" Fanless, streamlined enclosure for highly efficient heat dissipation Compliance with MIL-STD 810 & IEC 60068-2-27 for shock and vibration test Aluminum Housing with anti-corrosion 5 Wire Resistive Touch / anti-reflective protection glass Optional GPS, 3G/WLAN (Either one) Wide range 9-36 V DC input Mounting options suitable for vehicle mounting: VESA Mount, Yoke Mount and
Roof Mount
Compliance with EN50155
Page 14
User Manual Chapter 1 Introduction
14
G-WIN Vehicle Mount Panel PC
Panel PC
Quick Start Guide
Driver CD and User
Manual
Touch Driver CD
Varies by product
specifications
9152111I101W
IB32: 9171111I101Y
9171111T100D
3 Pin Terminal Block
Cable:94EL02X020E0 Connector: 604520105004
AC Adapter
Power Cord
WLAN Antenna
Mounting Bracket
50W:90PO12050000 80W:90PO12800000
Varies by
destination
391000020202
8.4” 99KK08Z00010
10.4”99KK00Z00010 15” 99KK15A00001
1.2 Package Contents
Carefully remove the box and unpack your device. Please check if all the items listed below are inside your package. If any of these items are missing or damaged contact us immediately.
Standard factory shipment list
Package may include the following items based on your order (optional)
Page 15
User Manual Chapter 1 Introduction
G-WIN Vehicle Mount Panel PC
15
1.3 Mechanical Concept
On the picture below you can see spare parts exploded drawing of a standard G-WIN Vehicle Mount Series Panel PC.
Page 16
User Manual Chapter 1 Introduction
16
G-WIN Vehicle Mount Panel PC
Icon
Button
Function
Power
Turn ON or turn OFF the Panel PC.
Brightness UP
Increase the brightness of the display screen, or allows user to navigate items of a single OSD menu.
Brightness DOWN
Decrease the brightness of the display screen, or allows user to navigate items of a single OSD menu.
Reset
Clear any pending errors or events and brings a system to normal condition or an initial state.
Indicator
Color
Definition
PWR
Green
Power is ON and the device functions normally
Orange
Panel PC is suspended
HDD Green
HDD is active OFF
HDD is inactive
1.4 Physical Button and LED Indicators
On-Screen Display (OSD) is a user-friendly interface to remote the display function and to adjust the display’s image properties. It also supports special Hot Keys for easy control, such as auto-adjustment and brightness control for backlight.
1.4.1 G-WIN Panel PC 8.4”, 10.4” and 12.1”
LED Indicators
Page 17
User Manual Chapter 1 Introduction
G-WIN Vehicle Mount Panel PC
17
Icon
Button
Function
Power
Turn ON or turn OFF the Panel PC.
Reset
Clear any pending errors or events and brings a system to normal condition or an initial state.
Lock / Unlock
Tap this button to lock / unlock the function of OSD panel.
Auto Dimming/ Manually
Tap the button once to AUTOMATICALLY adjust brightness mode.
Press the button again to MANUALLY adjust brightness mode.
Day/ Night Mode Tap this button to enter DAY MODE.
Tap this button to enter NIGHT MODE to increase visibility in low-light conditions.
Brightness UP
Increase the brightness of the display screen, or allows user to navigate items of a single OSD menu.
Brightness DOWN
Decrease the brightness of the display screen, or allows user to navigate items of a single OSD menu.
LED Adjustment
Adjust the brightness of the LED.
1.4.2 G-WIN Panel PC 15”
Page 18
User Manual Chapter 1 Introduction
18
G-WIN Vehicle Mount Panel PC
Indicator
Color
Definition
PWR
Green
Power is ON and the device functions normally
Orange
Panel PC is suspended
HDD Green
HDD is active OFF
HDD is inactive
LED Indicators
Page 19
G-WIN Vehicle Mount Panel PC
19
Getting Started
This chapter tells you important information on power supply, adapter and precautions tips. Pay attention to power considerations.
Page 20
User Manual Chapter 3 Operating the Device
20
G-WIN Vehicle Mount Panel PC
Size
8.4”
10.4”
12.1”
15”
AC Adapter
12V/ 50W
12V/ 50W
12V/ 50W
12V/ 80W
AC Adapter
Power Cord
3 Pin Terminal Block
Chapter 2: Getting Started
This chapter provides information on how to connect the device to the source of power, connector pinouts and the guideline to turn on/off the Panel PC.
2.1 Powering On
2.1.1 AC Adapter Components
AC Adapter specifications vary by panel size.
Safety Precautions:
Do not use the adapter in a high moisture environment Never touch the adapter with wet hands or foot Allow adequate ventilation around adapter while using Do not cover the adapter with paper or other objects that will reduce cooling Do not use the adapter while it is inside a carrying case Do not use the adapter if the cord is damaged There are NO serviceable parts inside Replace the unit if it is damaged or exposed to excess moisture
While using the AC Adapter always:
Plug-in the power cord to easy accessible AC outlet Plug-in the AC adapter to a grounded outlet
Page 21
User Manual Chapter 3 Operating the Device
G-WIN Vehicle Mount Panel PC
21
CAUTION/ATTENTION Use only the AC adapter included in your package (Rating: Output 12V/6.6 A). Using other AC adapters may damage the device. Utiliser seulement le convertisseur AC inclu avec votre appareil (Puissance: Sortie 12V/6.6 A). Utiliser d’autres convertisseurs pourraient endommager l’appareil.
ALTERNATING CURRENT / MISE À LE TERRE! This product must be grounded. Use only a grounded AC outlet. Install the additional PE ground wire if the local installation regulations require it.
*If you do not use a grounded outlet while using the device, you may notice an electrical tingling sensation when the palms of your hands touch the device.
Ce produit doit être mis à la terre. Utiliser seulement un cordon
d’alimentation avec mise à la terre. Si les règlements locaux le
requiert, installer des câbles de mise à la terre supplémentaires.
*Si vous n’utiliser pas une prise d’alimentation avec mise à la terre,
vous pourriez remarquer une sensation de picotement électrique
quand la paume de vos mains touche à l’appareil.
2.1.2 Power Considerations
The device operates on external DC power. Use the AC adapter included in the package.
Page 22
User Manual Chapter 3 Operating the Device
22
G-WIN Vehicle Mount Panel PC
1. Connect the 3-pin terminal block.
2. Screw the Terminal block to fix the cable.
1. Connect terminal block to the Panel PC.
+ Connect to power supply until 0V
-Connect to power supply until it get +9~36V DC
2.1.3 Connecting the Power
Connecting to DC Power Source
Cable Mounting Steps:
The device is ready to work once is connected to the source of power.
Page 23
User Manual Chapter 3 Operating the Device
G-WIN Vehicle Mount Panel PC
23
Note: Power cords vary in appearance by region and country.
Connecting to AC Power Source
Cable Mounting Steps:
2. Connect the AC adapter to the 3 pin terminal block located on the back side of the
Panel PC.
3. Connect the power cord to AC adapter.
4. Plug the power cord in to the AC outlet and the device will turn on automatically.
Page 24
User Manual Chapter 3 Operating the Device
24
G-WIN Vehicle Mount Panel PC
NOTE:
If your system is not Windows 7, the method to turn off the device may slightly vary.
2.2 Turning On and Off
To turn on the Panel PC:
1. Press the power on switch to turn the Panel PC on.
2. Press “DEL” to enter the CMOS setting and check the BIOS setup.
To shut down the Panel PC:
To shut down your device, do the following: Tap Start ( ) > Shut down.
Wait for your Panel PC to completely turn off before disconnecting the power cord (if necessary).
Page 25
User Manual Chapter 3 Operating the Device
G-WIN Vehicle Mount Panel PC
25
2.3 Installing Operating System
You may install your own OS if it is not installed. When installing OS to this Panel PC, please follow the steps and use external equipment such as Keyboard and Mouse. (a) Use external USB DVD-ROM to run the OS and Driver settings (as shown on the picture below).
2.4 How to Enable Watchdog
To enable Watchdog, you need to download Winmate Watchdog utility. Find more
information on Watchdog in “Watchdog Guide” that you can download from Winmate
Download Center or File Share. Refer to the Ch.7, “Technical Support” for more details. To enable watchdog in Watchdog AP follow the instructions below:
1. On the right bottom side of the desktop screen, click triangle button to show
hidden icons.
2. Click icon to open Watchdog utility.
3. In Watchdog utility window set countdown time and periodically feed time, or
disable watchdog.
Page 26
User Manual Chapter 3 Operating the Device
26
G-WIN Vehicle Mount Panel PC
Example:
Every 10 min watchdog will monitor the system, in case any error occurs the system will restart automatically when the countdown time reaches 0. Every 9 min watchdog timer will be reset to 10 min.
Settings
Description
Watchdog Countdown Time
The system automaticity restarts when this countdown time reaches zero.
Default: 10 min
Periodically Feed Time
To set a cycle time to automatically reset watchdog timer. Default: 9 min
Enable / Disable
Enable or disable watchdog. Default: Enable
Page 27
User Manual Chapter 2 Getting Started
G-WIN Vehicle Mount Panel PC
27
Page 28
User Manual Chapter 3 Operating the Device
28
G-WIN Vehicle Mount Panel PC
Safety Precautions:
Do not run signal or communication wiring and power wiring in the same conduit. To avoid interference, wires with different signal characteristics (i.e., different interfaces) should be routed separately.
Be sure to disconnect the power cord before installing and/or wiring your device.
Verify the maximum possible current for each wire gauge, especially for the power cords. Observe all electrical codes dictating the maximum current allowable for each wire gauge.
If the current goes above the maximum ratings (80 W), the wiring could overheat, causing serious damage to your equipment.
Be careful when handling the unit. When the unit is plugged in, the internal components generate a lot of heat which may lead the outer casing too hot to touch.
2.5 Connectors
2.5.1 Wiring Requirements
The following common safety precautions should be observed before installing any electronic device:
Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point.
Keep the wires separated according to interface. The rule of thumb is that wiring that shares similar electrical characteristics may be bundled together.
Do not bundle input wiring with output wiring. Keep them separate.
When necessary, it is strongly advised that you label wiring to all devices in the system.
Page 29
User Manual Chapter 2 Getting Started
G-WIN Vehicle Mount Panel PC
29
Description
Description
RS-232
1 x USB3.0, 1 x USB2.0
9-36V DC Terminal Block
HDMI1.4a
RS-232
2 x RJ45
Description
Description
9-36V DC Terminal Block
1 x USB3.0, 1 x USB2.0
CAN Bus or Digital I/O (Optional)
HDMI1.4a
RS-232
2 x RJ45
RS232/422/485
2.5.2 Connector Placement
G-WIN Panel PC comes with various interfaces located on the bottom panel. The I/O placement varies by processor and screen size of the Panel PC.
2.5.2.1 G-WIN Panel PC 8.4
R08IB3S-VMU1
2.5.2.2 G-WIN Panel PC 10.4
R10IB3S-VMT2, R10IB3S-VMP3, R10IB3S-VMP1
Page 30
User Manual Chapter 3 Operating the Device
30
G-WIN Vehicle Mount Panel PC
Description
Description
RS-232
HDMI1.4a
RS-232/ 422/ 485
2 x RJ45
1 x USB3.0, 1 x USB2.0
9-36V DC Terminal Block
Description
Description
9-36V DC Terminal Block
RS-232/ 422/485
RS-232 (Optional)
1 x USB3.0, 1 x USB2.0
RS-232
HDMI 1.4a
SIM Card Slot (Optional)
2 x RJ45
CANBUS/ DIO (Optional)
2.5.2.3 G-WIN Panel PC 12.1
W12IB3S-VMM9
2.5.2.4 G-WIN Panel PC 15
R15IB3S-VMA3(HB)
Page 31
User Manual Chapter 2 Getting Started
G-WIN Vehicle Mount Panel PC
31
Voltage
Minimum Voltage 9V Maximum Voltage 36V Maximum Current 6.6A
Pin №
Signal Name
Pin №
Signal Name
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR 8 RI 9 GND
10
GND
Pin
RS232
RS422
RS485
1
DCD
TxD-
D- 2 RXD
TxD+
D+ 3 TXD
RxD+
NC 4 DTR
RxD-
NC 5 GND
GND
GND 6 DSR
NC
NC 7 RTS
NC
NC 8 CTS
NC
NC
9
RI
NC
NC
2.5.3 Connector Description
This section contains the description of the G-WIN Panel PC (Bay Trail) external connectors.
2.5.3.1 Power Input Connector
G-WIN Vehicle Mount Panel PC uses 3 Pin Terminal Block for power input and accepts voltage 9-36V DC.
2.5.3.2 Serial Interface (RS-232)
Use RS-232 serial port connector to connect your Panel PC to external devices such as mouse, modem or printer. You can configure serial port settings via jumpers located on the motherboard.
2.5.3.3 Serial Interface (RS-232/422/485)
Use RS-232/422/485serial port connector to connect your Panel PC to external devices such as mouse, modem or printer.
Page 32
User Manual Chapter 3 Operating the Device
32
G-WIN Vehicle Mount Panel PC
Pin
Signal Name
Pin
Signal Name
1
+5V
2
USB_D-
3
USB_D+
4
GND
5
STDA_SSRX-
6
STDA_SSRX+
7
GND_DRAIN
8
STDA_SSTX-
9
STDA_SSTX+
10
+5V
11
USB_D-
12
USB_D+
13
GND
Pin
Signal Name
Pin
Signal Name
1
TMDS_DATA2+
2
GND
3
TMDS_DATA2-
4
TMDS_DATA1+
5
GND
6
TMDS_DATA1-
7
TMDS_DATA0+
8
GND
9
TMDS_DATA0-
10
TMDS_CLOCK+
11
GND
12
TMDS_CLOCK-
13
CEC
14
NC
15
DDC_CLOCK
16
DDC_DATA
17
GND
18
5V
19
Hot Plug Detect
Pin
Signal Name
Pin
Signal Name
1
TX1+
2
TX1- 3 TX2+
4
TX2- 5 TX3+
6
TX3-
7
TX4+
8
TX4-
2.5.3.4 USB 2.0/ USB 3.0 Connector
2.5.3.5 HDMI Connector
G-WIN Panel PC uses HDMI1.4a connector to connect to the external display.
2.5.3.6 Ethernet (LAN) Connector
The G-WIN Panel PC supports one RJ45 10/100/1000 Mbps Ethernet interface for connecting to the internet.
Page 33
User Manual Chapter 2 Getting Started
G-WIN Vehicle Mount Panel PC
33
Pin №
Signal Name
Pin №
Signal Name
1
GND
2
DO0 3 DO1
4
DI0 5 DI1
Voltage
Digital output
Open drain to 40V ; Maximum load 2.0A
Digital input
Level 0: close to GND; Level 1: 2.5~12V
2.5.3.7 Digital Input/ Output Connector (Optional)
Page 34
34
G-WIN Vehicle Mount Panel PC
Mounting Solutions
This chapter provides mounting guide for all available mounting options. Pay attention to cautions and warning to avoid any damages.
Page 35
User Manual Chapter 3 Mounting Solutions
G-WIN Vehicle Mount Panel PC
35
WARNING! / AVERTISSEMENT! Follow mounting instructions and use recommended mounting hardware to avoid the risk of injury. Suivez les instructions de montage et d'utilisation recommandé le matériel de montage pour éviter le risque de blessure.
WARNING! / AVERTISSEMENT! Observe all local installation requirements for connection cable type and protection level.
Suivre tous les règlements locaux d’installations, de câblage et niveaux
de protection.
WARNING! / AVERTISSEMENT! Turn off the device and disconnect other peripherals before installation.
Éteindre l’appareil et débrancher tous les périphériques avant l’installation.
ALTERNATING CURRENT / MISE À LE TERRE! To prevent electrical shock, the Safety Ground location on the rear must be bonded to the local earth ground through a minimum 12 AWG wire as short as possible Pour éviter les chocs électriques, lemplacement de la prise terre à l’arrière doit être lié à terre locale, à travers un 12 AWG minimum et aussi court que possible.
Chapter 3: Mounting Solutions
This chapter provides mounting guide for all available mounting options. Pay attention to cautions and warning to avoid any damages.
3.1 Cable Mounting Considerations
For a nice look and safe installation, make sure cables are neatly hidden behind the Panel PC. Refer to Chapter 2, section 2.1 for the cable installation instruction.
3.2 Safety Precautions
Observe the following common safety precautions before installing the equipment:
Use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must be crossed make sure the wires are perpendicular at the intersection point.
Keep the wires separated according to the interface. Do not bundle input wiring with output wiring. Keep them separate.
When necessary, it is strongly advised to label wiring to all devices in the system.
Page 36
User Manual Chapter 3 Mounting Solutions
36
G-WIN Vehicle Mount Panel PC
IMPORTANT:
Perform mounting after you establish all the necessary connections. Refer to Chapter 2 for wiring requirements and instructions.
Size
VESA Plate Dimensions
Screw hole diameter
8.4”, 10.4”, 12.1
75 x 75 mm
VESA M4x6 mm
15”
100 x 200 mm
VESA M6x8 mm
3.3 Mounting Guide
The device comes with different mounting options suitable for most of the industrial and commercial applications. There are two main mounting approaches - Vehicle Mounting (Dash/ Yoke Mounting) and VESA Wall Mounting; both approaches are very easy for user to set up the Panel PC.
3.3.1 VESA Mounting
G-WIN Vehicle Mount Panel PC compatible with VESA Mount solution. Follow the instruction below to complete mounting.
VESA Plate Installation
Page 37
User Manual Chapter 3 Mounting Solutions
G-WIN Vehicle Mount Panel PC
37
NOTE: Notice that both hooks on bracket should lock the notches on the back cover of the device.
Wall Mount
*with customer’s bracket
Mounting Steps:
1. Screw VESA Bracket to the fixture (ex. wall) with M4 flathead screws.
2. Place the device on VESA bracket.
3. Carefully mount the device to the fixture (for ex. wall).
4. When the installation is complete, plug the power cord into a grounded AC outlet. Turn on the power.
Page 38
User Manual Chapter 3 Mounting Solutions
38
G-WIN Vehicle Mount Panel PC
Size
Winmate Part Number
8.4”
99KK08Z00010
10.4”
99KK00Z00010
One bracket stand Three M5 x10 screws with washer One locking handle adjustment tool with
metal washer
3.3.2 Yoke Mounting
Yoke Mount solution allows to mount your device on a wall or ceiling. You can purchase dash/ yoke mounting kit from Winmate as an optional accessory.
Yoke Mounting Kit:
Yoke Mount Kit includes:
Page 39
User Manual Chapter 3 Mounting Solutions
G-WIN Vehicle Mount Panel PC
39
Mounting steps:
1. Place the G-WIN Vehicle Mount Panel PC on the bracket stand, aiming screw
hole for each other.
2. Secure three M5x10 screws to fix the device upon the bracket stand.
3. Secure tightly locking handle to the Panel PC.
Page 40
User Manual Chapter 3 Mounting Solutions
40
G-WIN Vehicle Mount Panel PC
4. Loosen the hand-screw adjustment tool, then you can adjust product angle on
the stand. Then screw the product tightly again to secure the stand position.
Page 41
User Manual Chapter 3 Mounting Solutions
G-WIN Vehicle Mount Panel PC
41
Size
Winmate Part Number
8.4”
98K008A0000R
10.4”
98K010A00018
3.3.3 Roof Mounting
Roof mounting allows mounting your device on the roof. You can purchase roof mounting kit from Winmate as an optional accessory.
U-Shape Mounting Kit:
Page 42
User Manual Chapter 3 Mounting Solutions
42
G-WIN Vehicle Mount Panel PC
U-Shape Mounting Kit Mechanical Drawing
For 8.4” G-WIN Vehicle Mount Panel PC
Page 43
User Manual Chapter 3 Mounting Solutions
G-WIN Vehicle Mount Panel PC
43
For 10.4” G-WIN Vehicle Mount Panel PC
p
Page 44
44
G-WIN Vehicle Mount Panel PC
Maintenance
This chapter provides information on regular cleaning and maintenance procedures. Follow all the recommendations included in this chapter in order to ensure long product lifecycle.
Page 45
User Manual Chapter 4 Maintenance
G-WIN Vehicle Mount Panel PC
45
CAUTION/ ATTENTION Always turn off the device and disconnect other peripherals before cleaning and maintenance procedures. Toujours éteindre l’appareil et débrancher tous les périphériques avant que les procédures de nettoyage et d'entretien.
WARNING!/ AVERTISSEMENT! POTENTIAL ELECTROSTATIC CHARGE HAZARD – SEE INSTRUCTIONS POTENTIEL ÉLECTROSTATIQUE CHARGE DANGER - VOIR INSTRUCTIONS
Chapter 4: Maintenance
This chapter includes regular cleaning and maintenance procedures. Follow all the recommendations in this chapter in order to ensure long product lifecycle.
This equipment is extremely rugged and does not require a lot of maintenance. Remember that electrical equipment should be handled with care and used accordingly to its specifications.
4.1 Cleaning the Display Screen
Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other
particles. Do not use acetone, ethyl alcohol, toluene, ethyl acid or methyl chloride to clear the panel. It may permanently damage the display screen.
You can apply a small amount of non-ammonia; non-alcohol based glass
cleaner onto a clean, soft, lint-free cloth and wipe the screen.
Never spray or pour any liquid directly on the screen or case. DO NOT use water or oil directly on the display screen. If droplets are allowed
to drop on the screen, permanent staining or discoloration may occur.
4.2 Cleaning the Casing
Use the following procedure to clean the equipment.
Before Cleaning:
Make sure the device is turned off. Disconnect the power cable from any AC outlet.
When Cleaning:
Wipe dust off the outside casing with a cloth slightly moistened with water or
mild ammonia-based cleaning solution. Do not use this cloth on a display screen!
Do not use an abrasive cleaner or high pressure washer on the screen. Do not rub the unit with a dry cloth. This action can result in a static charge being
built up and cause a spark. Always use damp cloth while cleaning the unit
Page 46
46
G-WIN Vehicle Mount Panel PC
Driver Installation
This chapter describes how to install all
necessary drivers.
Page 47
User Manual Chapter 5 Driver Installation
G-WIN Vehicle Mount Panel PC
47
NOTE:
For other drivers installation instructions and BIOS settings please refer to the Motherboard User Manual that can be found in the Driver CD included in the package.
Chapter 5: Driver Installation
This chapter provides guideline to driver installations.
The Panel PC comes with Motherboard User Manual and Driver CD according to the CPU, and contains most of the drivers and utilities that you need. To install Graphics, Chipset, VGA, Audio, SATA and Ethernet drivers, follow the step-by-step driver installation guide in the Motherboard User Manual (included in the package).
To install touch screen drivers (if necessary), follow the instructions included in this chapter.
Page 48
User Manual Chapter 5 Driver Installation
48
G-WIN Vehicle Mount Panel PC
5.1 ELO AccuTouch/ CarrollTouch Infrared Driver Installation
5.1.1 Downloading Drivers
ELO AccuTouch/ CarrollTouch infrared driver software provides a consistent software interface among all ELO AccuTouch/ CarrollTouch infrared touch screens and controllers.Go to http://www.elotouch.com/Support/dnld.asp for a complete list of available drivers.
For Driver Installation, please install the “ELO Touch System Touch Tools CD” for Windows XP Professional Embedded, Windows 2000, Windows Me, Windows 98, Windows 95, Windows NT, Windows CE 2.x, 3.0, 4.x, Windows XP Embedded, Windows
3.1, DOS, OS/2 Warp, and Apple Macintosh. Just follow the step by step to install the driver. Select “Auto-detect ELO devices” in the first step. If not, the following step will need users choose COM2 port for detecting the devices.
Page 49
User Manual Chapter 5 Driver Installation
G-WIN Vehicle Mount Panel PC
49
5.1.2 Configuration Utility
After finishing the installation, follow the steps below to test the configuration utility.
Step 1 Enter “My Computer”, click the “ELO Touch Screen” shortcut function.
Step 2 Click “Align” function key to continue.
Page 50
User Manual Chapter 5 Driver Installation
50
G-WIN Vehicle Mount Panel PC
Step 3 Calibrate four-point locations on the screen.
Step 4 Click Yes” if the cursor follows your finger and finish the utility test.
Page 51
User Manual Chapter 5 Driver Installation
G-WIN Vehicle Mount Panel PC
51
IMPORTANT:
Do not plug the USB controller on the system before the installation has been finished.
5.2 The Premier Touch Driver Installation
Touch-Kit is the Premier Touch software, which contains drivers of the touch panel controllers for the specified communication connectors, RS232, PS/2 and USB, and the other two utilities.
The two utilities are as follows:
Touch Tray support
This is utility for emulating the right and left button of mouse through controlling touch panel. Users can toggle between right/left mouse buttons by this utility.
Configuration support
The calibration and draw test of touch panel can be done by this utility. Besides, you can add or remove for new RS-232 or PS/2 touch panel devices.
5.2.1 Installing Touch Kit
Follow the steps below to install Touch Kit:
Step 1 Insert the Touch-Kit CD to CD-ROM. Step 2 Open the G-WIN Vehicle Mount Panel PC User Manual CD to “Touch _PM”
directory.
Step 3 Double-click the Setup.exe, then Windows starts to run the installation program.
Step 4 Click Next to continue installation. The system will automatically detect touch
devices connected to the COM2 port on your Panel PC.
Page 52
User Manual Chapter 5 Driver Installation
52
G-WIN Vehicle Mount Panel PC
Step 5 Follow on-screen instructions to finish the driver installation.
5.2.2 Configuration Utility
After finishing the touch driver installation, you need to test the configuration utility.
Step 1 Click the “Touch-Kit” shortcut function on the desktop.
Step 2 Enter “General” functions and choose the language you need. Then Enter “Tool”
function alignments to match the display. And go to the next step.
Page 53
User Manual Chapter 5 Driver Installation
G-WIN Vehicle Mount Panel PC
53
Step 3 Correct four-point locations on screen.
Step 4 Press “Yes” to continue if four-point calibration test is complete successfully and
press Ok to finish the screen calibration.
Page 54
54
G-WIN Vehicle Mount Panel PC
Troubleshooting
This chapter describes all known issues and
solutions.
Page 55
User Manual Chapter 6 Troubleshooting
G-WIN Vehicle Mount Panel PC
55
Chapter 6: Troubleshooting
This chapter describes all known issues and solutions.
6.1 Using USB-HDD or USB-CDROM for Booting OS
If you need to use USB-HDD or USB-CDROM for booting an operating system at start-up time, we recommend disabling the “Quick Power On Self Test” function in CMOS setting
Page 56
User Manual Chapter 6 Troubleshooting
56
G-WIN Vehicle Mount Panel PC
IMPORTANT:
While using CF card as storage of the Operation System, you need to use Fixed Disk Mode” type Compact Flash Card instead of removable disk mode. The internal Compact Flash socket is NOT A PLUG & PLAY DEVICE; you are allowed to remove the CF card only at POWER-OFF status.
Page 57
User Manual Chapter 6 Troubleshooting
G-WIN Vehicle Mount Panel PC
57
IMPORTANT:
Before starting the recovery process, be sure to backup all user data, as all data will be lost after the recovery process.
6.2 Using Recovery Wizard to Restore Computer
G-WIN Vehicle Mount computer has a dedicate recovery partition stored on the hard drive of the tablet to enable quick one-key recovery process. This partition occupies about 11GB of the storage space, and comes built-in to each G-WIN Vehicle Mount computer.
Follow the procedure below to enable quick one-key recovery procedure:
1. Plug-in the AC adapter to the computer. Make sure the computer stays plugged
in to power source during the recovery process.
2. Power on the tablet computer, and when the boot screen shows up, press the
Fn1 button (Recovery Key) on the front bezel OR press F6when using an external USB keyboard to initiate the Recovery Wizard.
3. The following screen shows the Recovery Wizard. Click on “Recovery” button to
continue.
Page 58
User Manual Chapter 6 Troubleshooting
58
G-WIN Vehicle Mount Panel PC
4. A warning message about data loss will show up. Make sure data is backed up
before recovery, and click on “Yes” to continue.
5. Wait till the recovery process to complete. During the recovery process, a
command prompt will show up to indicate the percent of recovery process. After recovery is completed, and the tablet computer will restart automatically.
Page 59
G-WIN Vehicle Mount Panel PC
59
Technical Support
This chapter includes technical support
pathway.
Page 60
User Manual Chapter 7 Technical Support
60
G-WIN Vehicle Mount Panel PC
Item
Type
Description
1
SDK
Digital I/O SDK
2
SDK
Watchdog SDK
3
Utility
Watchdog Utility
Chapter 7: Technical Support
This chapter includes information where to find technical support and Winmate’s
Software Developing Kit (SDK). If any problem occurs fill in Problem Report Form enclosed and immediately contact us.
7.1 Software Developer Support
We provide the SDK in the User Manual and SDK CD, or you can download the SDK from Winmate Download Center or Winmate Partner Portal.
The list of SDK for S-Series HMI:
Winmate Download Center:
Go to http://www.winmate.com.tw/ >Support > Download Center > Rugged Series > G­WIN Rugged PC-IB32
Or follow the link:
http://www.winmate.com/DownCenter/DownLoadCenter.asp?DownType=0907
Winmate File Share
Go to http://www.winmate.com.tw/ > Support > Partner Portal > Public Documents > Panel PC > G-WIN > IB32 (Celeron N2930)
Or follow the link below: https://winmate.box.com/v/GWIN-PPC-IB32
Page 61
User Manual Chapter 7 Technical Support
G-WIN Vehicle Mount Panel PC
61
Customer name:
Company:
Tel.:
Fax:
E-mail:
Date:
7.2 Problem Report Form
G-WIN Vehicle Mount Panel PC
Product Serial Number: _____________________________________________________
Problem Description: Please describe the problem as clearly as possible. Detailed description of the occurred problem will allow us to find the best solution to solve the problem as soon as possible. ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________
Page 62
62
G-WIN Vehicle Mount Panel PC
Panel PC Selection Guide
This section includes information on ordering G-WIN Series Panel PC.
Appendix
Page 63
User Manual Appendix A Panel PC Selection Guide
G-WIN Vehicle Mount Panel PC
63
LCD Spec.
Motherboard Model Name
Recommended Resolution
Display Color
IB32 SBC- Intel® Celeron® N2930
R08IB3S-VMU1
800 × 600
16.2M
R10IB3S-VMT2
1024 × 768
16.2M
R10IB3S-VMP3
640 × 480
262K
R10IB3S-VMP1
800 × 600
16.2M
W12IB3S-VMM9
1280 × 800
16.2M
R15IB3S-VMA3HB
1024 × 768
16.2M
Appendix A: Panel PC Selection Guide
A1 Panel PC Selection Guide
Page 64
64
G-WIN Vehicle Mount Panel PC
Motherboard Specifications
This section includes detailed hardware and hardware
specifications.
Appendix
Page 65
User Manual Appendix B Motherboard Specifications
G-WIN Vehicle Mount Panel PC
65
Item
Specifications
System Specifications
Processor
Intel® Celeron N2930 1.83 GHz Processor
System Chipset
Intel® Atom SoC integrated
BIOS
AMI 16Mbit Flash
System Memory
1 x SODIMM socket, support up to 8GB DDR3L 1600
Audio
Realtek HD Audio Codec
Ethernet
Intel® I210 GbE LAN
LCD Support
LVDS: Dual-channel 24 bit LVDS Up to 1920 x 1080 @ 60Hz VGA Mode : Up to 1600 x 1200 @ 60Hz DVI : 1920 x 1080 @ 60Hz
Storage
8.4 PPC
10.4/ 12.1/ 15 PPC
Default
mSATA 64GB SSD
mSATA 64GB SSD
Optional
-
2.5” SSD
2.5” HDD
Input/ Output Connectors
Ethernet LAN
2 x GigaLAN (Intel WG82574L GbE controller)
USB
1 x USB3.0, 5 x USB2.0 (4 x pin-header)
Serial Port
3 x RS-232(pin-header), 1 x RS-232/422/485 (Rear I/O)
Expansion Slots
1 x Mini PCIe slot (for wireless module) 1 x Mini PCIe slot (for SATA SSD)
Power Requirements
Power Input
9~36V (Default) or DC IN 12V (Optional)
Mechanical Dimensions
Form Factor
3.5
Operation System
Appendix B: Motherboard Specifications
B1 Intel IB32 (Intel Atom SoC Based)
Page 66
User Manual Appendix B Motherboard Specifications
66
G-WIN Vehicle Mount Panel PC
Supported OS
Windows Embedded Standard 7 Windows Embedded 8 Standard Windows Embedded 8.1 Industry Pro Windows 10 IoT Enterprise Linux
Page 67
G-WIN Vehicle Mount Panel PC
67
Touchscreen
This section includes information on touch panel solutions supported by G­WIN Series Panel PC, its technology and specifications.
Appendix
Page 68
68
G-WIN Vehicle Mount Panel PC
COM Port
Touch Interface
1 x RS-232
2 x RS-232
Optional
RS-232 (default via
COM2)
USB
USB
Appendix C: Touchscreen
This section includes information on projected capacitive touchscreen (p-cap), its technology and specifications.
C1 Overview
The Panel PC supports three kinds of Touch Panel Solutions: ELO AccuTouch touchscreen, ELO Infrared touch-screen and Premier Touch system. All of the touchscreens consist of a touch-screen and an electronic touch-screen controller.
The G-WIN Vehicle Mount Panel PC touch device uses RS-232 interface touch controller card via the COM2 port Note inside Panel PC. When the touch driver installed either for ELO or Premier Touch systems, it will detect COM2 port automatically.
The ELO AccuTouch and Premier Touchscreen are based on patented resistive technology. The touchscreen may be flat, spherical, or cylindrical. It is installed over the face of the display. Since its shape matches of the display face, the touchscreen has excellent clarity and minimal parallax.
The ELO CarrollTouch infrared (IR) technology uses a small frame around the display with LEDs and photoreceptors on opposite sides, hidden behind an IR-transparent bezel. The Controller sequentially pulses the LEDs to create a grid of IR beams. A touch obstructs one or more the beams which identify the X and Y coordinates. CarrollTouch technology combines superior optical performance with excellent gasket-sealing capabilities, so it's an excellent choice for harsh industrial and outdoor kiosk applications. Touched with a finger, gloved hand, fingernail, or stylus, it delivers a fast, accurate response every time.
C2 Recommended Touch Interface
Page 69
Winmate Inc.
9F, No.111-6, Shing-De Rd., San-Chung District, New Taipei City 24158, Taiwan, R.O.C
Tel: 886-2-8511-0288 Fax: 886-2-8511-0211 Email: sales@winmate.com.tw Official website: www.winmate.com
Loading...