Winmate 4300WBW User Manual

E430T Series

Elegant Industrial PDA

User Manual

Notes:

 All screens in this guide are simulated. Actual displays may be different.

 Depend on the different software version on your E430T; you may get different screens with same

tasks.

 Unless specified otherwise, all instructions to perform tasks in this guide assume that you are starting

from the home screen.

FEDERAL COMMUNICATIONS COMMISSION

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.

This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

RF exposure warning

The equipment complies with FCC RF exposure limits set forth for an uncontrolled
environment.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

RF exposure information (SAR)

This Elegant Industrial PDA meets the government's requirements for exposure to
radio waves. This Elegant Industrial PDA is designed and manufactured not to
exceed the emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government. The exposure
standard for wireless Elegant Industrial PDA employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
Tests for SAR are conducted using standard operating positions accepted by the
FCC with the Elegant Industrial PDA transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest certified
power level, the actual SAR level of the Elegant Industrial PDA while operating can
be well below the maximum value. This is because the Elegant Industrial PDA is
designed to operate at multiple power levels so as to use only the poser required to
reach the network. In general, the closer you are to a wireless base station antenna,
the lower the power output. The highest SAR value for US model Elegant Industrial
PDA as reported to the FCC when tested for use at the body, as described in this
user guide, is 0.770 W/kg.

Before starting to use E430T

1) Insert Micro SD / SIM card (Optional)

The built-in storage space of your E430T series PDA is mainly used for operation system. To enable some

functions need bigger storage space, such as camera or other APP, please insert a Micro SD card before

using.

2) Charge the Battery

The battery in your new E430T series device is not charged yet. Please charge with the bundled USB

cable before your first use.

Caution! Please don’t remove the battery pack or try to take this PDA apart while the E430T is charging.

These actions will result in some damages and may invalidate your warranty.

3) Some tips for using and caring your PDA

Your E430T series PDA is designed to resist damages from certain rugged conditions. However, to help

care for your PDA, please avoid prolonged or extreme exposure to those conditions.

 To ensure the rugged design works and protects your PDA, please be sure the USB connector

cover is closed and the back cover is screwed properly.

 Don’t leave your PDA near a heat source; this can damage the device.
 Avoid dropping your PDA on a hard surface; this can potentially cause damage to the device.
 To clean your PDA, use a dry soft cloth. Don’t use alcohol or other cleaning solutions.
 Please don’t have your PDA contact with water when the cover is opened. The water-proof design

works only when the outer case is sealed properly.

Note: Certain apps and features may not be available in all countries.

To know your Ex430xx more

Volume

Power:

Press = sleep
hold = power

Function Key

3.5 mm

headset

Webcam

Proximity & Light Sensor
IR

LED indicator

Earpiece

4.3” Touch

Screen

Home

Menu

Back

Search
Micro USB

Microphone

the important keys & connectors

Front View

Back View

LED

5M Pixels Camera

Speaker