2X100W COB LED Blinder
Warm White
USER MANUAL
Thank you very much for choosing our product. For safety purpose, please
read this manual carefully before your operation. This manual included
installation and using information. Please install and operate it according to
this manual.
1
Part 1 PRDUCT
1.1 Product introduction
This product is designed for indoor use. Suitable applications include wash or
effect lighting for architectural or stage applications. This product can also be
installed for use in signage and advertising using the dynamic functions
available with DMX512 control. Direct input of DMX512 signal allows the units
to be controlled from any DMX512 controller. This product can be operated as
a single unit or in multiple units for large applications.
1.2 Technical Specifications
Voltage：AC 100-240V，50/60HZ
Power：230W
Light Source：2 PCS 100W Warm White COB LED
LED Lifespan: Around 50,000 Hours
Color：Warm White 3000±200K/optional
Color Temperature：3200K
Beam Angle: 60 degree
Dimmer：Linear dimming 0-100%
Strobe：0-25t/s
Control Mode：DMX 512,Master/Slave, Manual mode
DMX Channel：1/2/6CH
DMX512 Pixel control
Size: 395*190*253mm
N.W: 3.7KG
1.3 Safety Warning
IMPORTANT:
ALWAYS READ THE USER MANUAL BEFORE OPERATION. PLEASE
CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS
THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA.
● This product must be installed by a qualified professional.
● Always operate the equipment as described in the user manual.
● A minimum distance of 0.5m must be maintained between the equipment
and combustible surface.
● The product must always be placed in a well ventilated area.
● Always make sure that the equipment is installed securely.
2
● DO NOT stand close to the equipment and stare directly into the LED light
source.
● Always disconnect the power supply before attempting and maintenance.
● Always make sure that the supporting structure is solid and can support
the combined weight of the products.
● The earth wire must always be connected to the ground.
● Do not touch the power cables if your hands are wet.
ATTENTION:
● This product left the place of manufacture in perfect condition. In order to
maintain this condition and for safe operation, the user must always follow
the instructions and safety warnings described in this user manual.
● Avoid shaking or strong impacts to any part of the equipment.
● Make sure that all parts of the equipment are kept clean and free of dust.
● Always make sure that the power connections are connected correct and
secure.
● If there is any malfunction of the equipment, contact your distributor
immediately.
● When transferring the product, it is advisable to use the original packaging
in which the product left the factory.
● Shields, lenses or ultraviolet screens shall be changed if they have
become damaged to such an extent that their effectiveness is impaired.
● The lamp (LED) shall be changed if it has become damaged or thermally
deformed.
PART 2 INSTALLATION
2.1 Mounting:
2.1-1 Hanging
The product can be mounted in a hanging position using the supporting
bracket. The bracket should be secured to the mounting truss or structure
using a standard mounting clamp. Please note that when hanging the unit a
safety cable should also be used
.
2.1-2 Upright
The product can be mounted in an upright or sitting position using the
supporting brackets.
NOTE:
The product can be mounted at any angle and in any position. It is possible to
3
further adjust the angle of the product using the two adjustment knobs located
on the side of the fixture.
2.2 DMX Channel instruction
1 Channel Mode
Channel
Function
Instruction
CH1
WW Dimmer
WW Dimmer- Dark to Bright
2 Channels Mode
Channel
Function
Instruction
CH1
WW Dimmer
WW Dimmer- Dark to Bright
CH2
CW Dimmer
CW Dimmer- Dark to Bright
6 Channels Mode
Channel
Function
Instruction
CH1
Total Dimmer
Total Dimmer- Dark to Bright
CH2
Total Strobe
Total Strobe- Slow to Fast
CH3
Built-in programs
Built-in programs
CH4
Function/Speed
Speed from slow to Fast
CH5
WW Dimmer
WW Dimmer- Dark to Bright
CH6
CW Dimmer
CW Dimmer- Dark to Bright
2.3 Special construction for DMX connection
☆ At last fixture, the DMX cable has to be terminated with a terminator to
reduce signal errors. Solder a 120-ohm 1/4W resistor between pin
2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
☆ If the controller is 5-pin output, it’s necessary to use an adaptor to transfer
signal from 5-pin output to 3-pin XLR-plug or you can connect cables as
following:
4
2.4 Master/Slave Operation.
The product can be linked together to work in Master/Salve mode without any
console. The 1stmachine will be set as Master and others will work as Salve
unit at same effect.
PART 3 Display Panel Operation
3. 1 Displ ay p an el me nu in str uc tio n
[MENU] menu selection or return to previous menu.
[UP] press [UP] through the menu list to increase/change the value of the
current function.
[DOWN] press [DOWN] through the menu list to decrease/change the value
of the current function.
[ENTER] confirm & quit out current function setting.
3. 2 Di sp l ay M enu ins tr u ct ion ( ge ner al)
No
Show
Function
Value
Instruction
1
A001
DMX address
001~512
6CH mode,UP,DOWN increase
or reduce the value,
5
2
D001
DMX address
001~512
2CH mode UP, DOWN
increase or reduce the value
3
H001
DMX address
001~512
1CH mode UP, DOWN
increase or reduce the value
4
CC00
Running mode
01 ~ 06
UP,DOWN change the mode
5
CP00
Colors Gradate
01 ~ 99
UP,DOWN change the speed
6
DE00
Colors Pulse
01 ~ 99
UP,DOWN change the speed
7
BEb1
Sound mode
Sound mode
8
O255
WW1 brightness
000-255
UP,DOWN adjust brightness
9
Y255
WW2 brightness
000-255
UP,DOWN adjust brightness
10
N000
Strobe
000-255
UP,DOWN change speed
Part 5, Maintenance
The cleaning of internal must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture
operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the fixture’s optics.
● Clean with soft cloth using normal glass cleaning fluid.
● Always dry the parts carefully.
● Clean the external optics at least every 20 days.
● Clean the internal optics at least every 30/60 days – Up to vary products.
Please ask professional technical to clean waterproof products and make
sure the fixture will be reassembled well for waterproof.
Loading...