Winix NK100 User Manual
User Manual
Model
Use & Care
Guide
NK100
xPlease read and follow all safety rules and instructions in
this manual before operating.
xThe product warranty is printed on the back of this guide,
so please keep it in a safe place for future use.
xThis product is manufactured for use only in USA/CA
CONTENTS
4-Stage Air Purification 5
Controls 6
Set Up
Where to use 7
Filter Anatomy 8
Installing the filters 10
Safety Instructions
Safety and Cautions 12
Operation
Initial Operation 13
Modes of Operation 14
Features and Settings 15
Care and Maintenance
Filter Care 17
Cleaning Care 21
Troubleshooting
Frequently Asked Questions 22
Unit Specifications 24
Product Warranty 26
Français
26
Espanol 51
This product is suitable for 120V only.
English
NK100
2
4-STAGE AIR PURIFICATION
Power cord with plug
(This product is suitable for
120V only.)
➍ PlasmaWave
®
VOC Smart Sensor
360o All-in-One True HEPA
Filter
➊ Pre-Filter
➋ True HEPA
➌ CD Carbon Filter
Back panel
PACKAGE
CONTENTS
Unit 360o All-in-One True
English
HEPA Filter
User Manual
NK100
3
CONTROLS
Air Outlet Vent
Mode Button
- Press to cycle through manual fan speeds (Low, Medium, High, Turbo).
- Pressing will also cycle through Auto and Sleep Modes.
- When sleep mode is selected the Air Quality Indicator light will be turned off.
- Press and hold for at least 3 seconds to enable or disable PlasmaWave
Air Quality Indicator
Color-coded LED indicates
one of three levels of air
quality.
®
.
Reset Button
After replacing a filter,
press the RESET button
for at least 5 seconds.
Light Sensor
Detects the
amount of
ambient light
within the
environment,
to adjust the
brightness
of the LED
indicators.
Power Button
Turns the unit
on or off.
English
Change Filter Indicator
LED light indicates when it is time to
change the filter.
PlasmaWave® Indicator
Indicates whether
PlasmaWave
disabled.
®
is enabled or
Child Lock Button
Press and hold for 3
seconds to enable
or disable the Child
Lock mode.
NK100
4
WHERE TO USE
Allow 12 ~ 18 in. of space between TVs, radios, and other electronic products
electromagnetic interference from certain electronics may cause product malfunction.
Place indoors away from direct sun light
direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
flimsy or slanted surfaces may result in abnormal noise and vibrations.
WARNING
Do not use around mist or fumes from
industrial oil or around large quantities of
metallic dust
Do not install in any sort of motor or
transport vehicle (trucks, boats, ships, etc.)
Do not place near any flammable materials
(aerosols, fuel, gases etc.)
Do not place below any electrical outlet
Follow these instructions to reduce the risk of serious
injury or death and to reduce risk of damaging the unit.
Do not place around heating elements
Do not place in an area with excessive
amounts of noxious gases
Do not have unit facing into wind or draft
Do not place in excessively humid areas
where unit may become wet
This unit is not intended to be used to preserve documents or in art conservation.
English
NK100
5
360o All-in-One True HEPA Filter
➊ Pre-Filter ➋ True HEPA ➌ CD Carbon Filter
English
NK100
6
360o All-in-One True HEPA Filter ANATOMY
➌ CD Carbon Filter
➋ True HEPA
➊ Pre-Filter
➊ Pre-Filter designed to catch larger airborne particles
found indoors.
➋ True HEPA
captures 99.97%* of airborne allergens
including; pollen, mold spores, dust, pet dander, microbes,
and smoke. *particles as small as 0.3 microns in size
➌ CD Carbon Filter reduces VOCs and household odors
from cooking, pets, and smoke.
• The 360o All-in-One True HEPA Filter is one unit and the
Note
individual components of the filter cannot be purchased
separately.
English
NK100
7
INSTALLING FILTERS
This product comes with all required filters. The protective plastic wrap
must be removed from the filter before use.
※ Operating the unit without removing the plastic wrap may result in
product failure.
※ Unplug and make sure the unit is turned off before installing filter.
① Remove the back panel by grasping
handle and pulling back, towards
yourself.
Latch
② Once the back panel is removed, grasp
the handle near the bottom of the unit,
and pull towards yourself to lower and
release the filter.
③ Remove the 360o All-in-One True
HEPA filter from the unit. Remove the
plastic wrap from the filter.
• Operating the unit without removing
filters from plastic wrap may cause
abnormal noise, deformation, or fire as a
result of overheating.
• Refer to pages 17 - 19 for details on how to replace filters.
Note
English
NK100
8
INSTALLING FILTERS
④ Install the filter, top side up, into the
unit until it is fully inserted. Grasp
lower handle near bottom of the
unit and push in until the filter locks
into place.
•
The top of the filter shows the opening
into the filter. Whereas the bottom is
solid, with no opening.
•
When installing the filter you will know
it is fully inserted because it will no
longer be able to be pushed further.
⑤ Replace the back panel by first
inserting the latch at the bottom
edge into the base of the unit, then
rotate the panel upward toward the
top of the unit until the panel snaps
into the unit.
Latch
⑥ When to service and replace filter:
Filter Indicator Light
※ Intervals between filter replacement may vary depending on environment.
※ For optimal use, the filter can be cleaned once every 14 days.
※ To clean the filter, vacuum the outside of the filter with a soft brush.
※ THIS FILTER CANNOT BE WASHED
When to
service
Clean once
every 14 days
When to replace
Lasts up to
12 months
To purchase replacement
Winix filters:
(877)-699-4649
www.winix.com
English
NK100
9
SAFETY AND CAUTIONS
Before operating this equipment, carefully read and follow these safety
cautions
Ensure filter is inserted before running unit
running unit without the filter can shorten the units life and cause electric shock or injury.
Be sure foreign objects are NOT inserted into the vents on the unit
objects can include pins, rods, and coins.
Do not touch any part of the interior of the unit with wet hands
the high voltage may cause electric shock.
Ensure unit intake and outlet vents do not become blocked
blockage may lead to increased internal termperatures causing product failure and derformation.
Do not use the unit as a step stool or place heavy objects on it
personal injury may occur or product failure and deformation.
WARNING
Do not pull on the power cord when
unplugging the unit
If the unit becomes submerged in water,
unplug it and contact customer service
Do not plug additional appliances into the
same outlet or power supply
Unplug unit when not in operation for
extended periods of time
English
Follow these instructions to reduce the risk of serious
injury or death and to reduce risk of damaging the unit.
Do not tie or knot power cord when unit
is in operation
Do not unplug or move the unit while in
operation
Do not touch the plug with wet hands
Cord can become damaged by forcefully
bending, pulling, twisting, bundling,
pinching or placing heavy objects on it
NK100
10
INITIAL OPERATION
①
Insert the power cord into an electrical
outlet.
②
Press the ‘Power’ button.
• During the first 4 minutes of power up, the Air Quality
Note
Indicator will flash as the Smart Sensor measure the air quality
in the environment, after which normal operation will begin.
③
By default, when the unit first powers
on, the mode will be set to Auto with
PlasmaWave
• When in Auto mode, the fan speed will
be automatically adjusted according to
the environments air quality.
• PlasmaWave
airborne contaminants.
Note
English
®
enabled.
®
works to remove harmful
• In Auto mode, as the indoor air quality improves, the fan
speed will automatically be reduced to Low.
• When the unit is running, you may hear a chirping or buzzing
sound. The sound is from large particles passing through
PlasmaWave
failure. To disable PlasmaWave
®
, it is normal and does not signify product
®
, see page 15.
NK100
11
AUTO & SLEEP
1. Auto Mode
Enables auto operation based on the unit's air quality Smart Sensor.
① Press the Mode button to select
Auto mode.
•The LED ‘Auto’ light will indicate
when Auto mode is activated, and
operation will begin.
Note
• When in Auto mode the fan speed is automatically adjusted
according to the indoor air quality. As the indoor air quality
improves, the fan speed will automatically be reduced. If the
indoor air quality decreases, the fan speed will automatically
increase.
2. Sleep Mode
Press the Mode button to select
Sleep mode.
• The LED "Sleep" light will indicate when
Sleep mode is activated, and operation will
begin.
AUTO
SLEEP
English
• When Sleep mode is selected, the fan speed is automatically
Note
set to Low. The fan speed can be manually changed by
pressing the Fan Speed button, changing the unit into manual
mode.
• When Sleep Mode is activated, the Air Quality Indicator LED
light is disabled.
NK100
12
MANUAL & PLASMAWAVE
®
3. Manual Mode (setting fan speed)
Users can opt to manually set the fan speed to Low, Medium, High, or
Turbo.
① Press the Mode button to set the
desired fan speed.
•When the button is pressed the unit
will cycle through Auto Mode, Sleep
Mode and fan speeds (Low, Medium,
High, Turbo).
• When Manual Mode is selected, Auto and Sleep Modes are
Note
automatically disabled.
4. PlasmaWave
By default, PlasmaWave® is enabled whenever the unit is powered on.
®
① When the unit is on, press and
hold the Mode button for at least
3 seconds to enable or disable this
feature.
•When PlasmaWave® is enabled the
indicator light will be on. When it is
disabled the light will be off.
• In Auto mode, as the indoor air quality improves, the fan
Note
English
speed will automatically be reduced to Low.
• When the unit is running, you may hear a chirping or buzzing
sound. The sound is from large particles passing through
PlasmaWave
failure.
®
, it is normal and does not signify product
3
seconds
NK100
13
CHILD LOCK & AIR QUALITY INDICATOR
5. Child Lock
Prevents children from pressing buttons and changing controls.
① When the unit is on, press and hold
the Child Lock button for at least 3
seconds to enable or disable this
feature.
•When Child Lock is enabled the
indicator light will be on. When it is
disabled the light will be off.
• When Child Lock is enabled, the control panel cannot be
Note
6. Air Quality Indicator
When on, the LED light will indicate the current indoor air quality
according to three levels: BLUE (good), AMBER (fair), RED (poor).
used.
English
Air Quality Indicator
• Air quality level is displayed on the indicator, based on the
Note
Smart Sensor. Depending on the immediate environment,
the indicator may change frequently in color or stay the same
for lengthy periods of time.
• When the unit is in Sleep Mode the Air Quality Indicator will
be turned off to allow for ultimate night time operation.
NK100
14
FILTER CARE
1. Know The Filters
When the Check Filter indicator LED is on, it is time to replace the filter.
Filter Indicator Light
When to
service
When to replace
※ Intervals between filter replacement may vary depending on environment.
※ For optimal use, the filter can be cleaned once every 14 days.
※ To clean the filter, vacuum the outside of the filter with a soft brush.
※ THIS FILTER CANNOT BE WASHED
Clean once
every 14 days
Lasts up to
12 months
To purchase replacement
Winix filters:
(877)-699-4649
www.winixamerica.com
360o All-in-One True
HEPA Filter
English
• The filters’ life varies depending on the level of pollutants in
Note
the air. The more dust present in the environment, the more
dust accumulates in the filters, shortening the life.
• If the filter is heavily soiled or has a bad odor, or if the fan
strength is significantly weakened, replace the filter even if the
Change Filter indicator has not yet turned on.
NK100
15
FILTER CARE
2. Removing Filters
Turn the unit power off before removing filters.
Latch
①
Remove the back panel by grasping the handle and gently pulling
towards yourself.
②
Grasp the lower handle on the unit and pull straight out, towards
yourself until the filter is released.
③
Pull out the 360o All-in-One True HEPA Filter.
3. Preparing New Filters
①
Remove replacement filter from
protective plastic wrap.
• Operating the unit without removing
filters from plastic wrap may cause
abnormal noise, deformation, or fire as
a result of overheating.
▶▶
English
NOTICE
• For optimal performance, only genuine Winix filters should
be used with this unit.
NK100
16
FILTER CARE
4. Replacing Filters
▶
▶
① I
nstall the filter, top side up, into the unit until it is fully inserted.
Grasp lower handle near bottom of the unit and push in until the filter
locks into place.
•
The top of the filter shows the opening into the filter. Whereas the bottom is
solid, with no opening.
•
When installing the filter you will know it is fully inserted because it will no
longer be able to be pushed further.
Latch
② Replace the back panel by first inserting the latch at the bottom
edge into the base of the unit, then rotate the panel upward toward
the top of the unit until the panel snaps into the unit.
5. Resetting The Unit
①
After replacing the filter, turn the
power back on and then press and
hold the Check Filter button for at
least 5 seconds to RESET the filter
life in your unit.
English
NK100
17
FILTER CARE
6. Cleaning the filter
Intervals between filter cleaning may vary depending on the air quality.
① Clean with a vacuum or a soft brush
•Only clean the pre-filter.
•This filter CANNOT be washed.
NOTICE
• Do not use benzene, alcohol, or other volatile fluids, which
may cause damage or discoloration.
English
NK100
18
CLEANING CARE
2. Cleaning the Exterior & Interior
① Wipe with a soft damp cloth
using room temperature water.
Afterwards, wipe it down with a
clean dry cloth.
•To keep unit in peak condition, clean
every 1-2 months.
① In order to clean the interior, open
the back panel and remove filter,
then use vacuum cleaner to remove
excess dirt and dust.
•For optimal performance, clean every
1-2 months.
English
NOTICE
•When cleaning the unit, always unplug the power cord first
and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
•Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is unplugged.
NK100
19
FREQUENTLY ASKED QUESTIONS
Problem Check / Actions to take
• Is the plug securely attached to the outlet?
- Make sure the outlet has power going to
It does not
turn on at all.
it, and ensure the plug is secured.
• Is there a power outage?
- Check to see if other lights and electrical
equipment are working and try again.
It doesn’t work
in Auto Mode.
English
• Has Auto Mode been selected?
- Press the Mode button until Auto Mode is
selected.
• Is the sensor blocked or clogged?
- Wipe VOC Smart Sensor with wet cloth,
then dry.
NK100
20
FREQUENTLY ASKED QUESTIONS
Problem Check / Actions to take
•
It vibrates and makes
a lot of noise.
Is it running on a slanted or uneven surface?
- Move the unit to a hard, flat, even area of
the floor.
The power plug and
outlet feel hot.
There is a
strange smell.
The fan
strength is weak.
The unit is not
purifying the air.
The display
panel is dim.
• Is the plug securely plugged in?
- Make sure the plug is properly plugged
into the outlet.
• Is it being used in a place with a lot of
smoke, dust, or odours?
- Clean the air intakes on either side and
clean the pre-filter.
- Clean or change the filter.
• Is the Check Filter indicator light on?
- Change the filters as required.
• I
s the Light Sensor blocked by debris?
- When Auto Mode is on, Sleep Mode
is automatically activated when the Light
Sensor detects that the room is dark.
English
NK100
21
UNIT SPECIFICATIONS
Model Name
NK100
Power Voltage AC120V/ 60Hz
Power Rate 55W
Room Area Served AHAM verified at 320 sq. ft.
Dimensions 12.2 in(W) x 12.2 in(D) x 29.5 in(H)
Weight 17 lbs
Replacement Filter
Filter N / item: 112180
※ The exterior, design, and product specifications may be changed without prior notice
to improve product performance.
Warning: Change or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, and may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be dteremined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
x
Reorient or relocate the receiving antenna.
x
x
Increase the separation between the equipment and receiver.
x
x
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
x
x
Consult the dealer or on experienced radio/TV technician for help.
x
This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two
conditions:
x
This device may not cause interference; and
x
x
This device must accept any interference, including interference that may cause undesired operation of the
x
device.
English
NK100
22
SAFETY INSTRUCTIONS
Thank you for purchasing a Winix air purifier. This product is for household use only.
IMPORTANT CAUTIONS FOR
USING YOUR AIR PURIFIER
WARNING: Follow the instructions in
this manual to reduce the risk of
electric shock, short circuit, and/or fire.
x
Do not repair or modify the unit unless
x
specifically recommended in this manual.
All other repairs should be completed by
a qualified technician.
x
The plug for this unit is polarized with
x
one blade wider than the other. Do not
force the plug into an electrical outlet. Do
not alter the plug in any way. If the does
not fit into the outlet, reverse the plug.
If it still does not fit, contact a qualified
technician to install a proper outlet.
x
Do not use if the power cord or plug is
x
damaged or the connection to the wall
outlet is loose.
x
Use AC 120V only.
x
x
Do not damage, break, forcefully bend,
x
pull, twist, bundle, coat, pinch, or place
heavy objects on the power cord.
x
Periodically remove dust from the power
x
plug. This will reduce the risk of shock due
to humidity build up.
x
If the power plug is damaged, it must
x
be replaced by the manufacturer or a
qualified technician.
x
Remove the power plug from the outlet
x
before cleaning the unit. When removing
the power plug, grasp by holding the
plug itself, never hold by the cord.
x
Remove the power plug from the outlet
x
when not in use.
x
Do not handle the power plug with wet
x
hands.
x
Do not operate the unit when using
x
indoor smoke-generating insecticides.
x
Do not clean unit with benzene or paint
x
thinner. Do not spray insecticides on the
unit.
x
Do not use the unit where it is humid or
x
where the unit may become wet, such as
the bathroom.
x
Do not insert fingers or foreign objects
x
into air intake or outlet.
x
Do not use use the unit near flammable
x
gases. Do not use near cigarettes, incense,
or other spark-creating items.
x
Unit will not remove carbon monoxide
x
emitted from heating appliances or other
sources.
IMPORTANT PRECAUTIONS FOR
USING YOUR AIR PURIFIER
x
Do not block the intake or outlet vents.
x
x
Do not use near hot objects, such as a
x
stove.
x
Do not use where the unit may come into
x
contact with steam.
x
Do not use the unit on its side.
x
x
Keep away from products that generate
x
oily residue, such as a deep fryer.
x
Do not use detergent to clean the unit.
x
x
Do not operate without a filter.
x
x
Do not wash and reuse the filter.
x
x
Hold the handle on the back of the unit
x
to transport.
x
Do not hold by the front panel.
x
WARNING
This product contains chemicals
known to the State of California to
cause cancer and birth defects or
other reproductive harm.
English
NK100
23
Loading...