WINIADAEWOO DSP5014LX User Manual

Page 1
48586120E101-R0
Page 2
PLASMA DISPLAY
USER’S MANUAL
DSP-5014LX
Proper use guarantees
product life.
Before using the product, be advised that you read this owner’s manual well and try to operate it.
- Product Warranty is included -
Page 3
2
This Owner’s Manual presents safety precautions and how to use the product. After reading it thoroughly, use the product safely. Keep this manual where the user can see it easily.
Failure to comply with warnings and cautions for the safe use of electric appliances may cause fire or human injury.
•50” XGA wide Plasma Panel
• DVD Direct Connection / Outstanding Picture Quality Digital Broadcasts Receive (HD Grade)
DVD can be directly connected to the unit so that you can view clear digital images. You can enjoy even higher quality images. by connecting digital broadcasting receiver with which digital broadcasts can be viewed.
PC Direct Connection
PC can be connected to the PDP without a separate device, and can be used as a monitor so that the effect of presentation gets maximized, making it more popular in various events and exhibitions.
160º Wide-Angle Viewing Area
Flat Panel with No Distortion and Color Blurring
Since Plasma Monitor has no problems such as distortion, blurring, flickering unlike existing CRT type, you can enjoy Home Theater with super speaker.
Various Video Control
- 11 Languages OSD - 20 Step screen zooming function - Full-screen still function
- Various aspect ratio (16:9, Panorama, Normal, Enlarge LB, Enlarge LBS)
Worldwide : NTSC, PAL, SECAM / Free Volt (100-240V 50/60Hz)
DVI (Digital Visual Interface) Connection
When connection to PC, you can receive DVI digial signal as well as former analog signal by using DVI input and D-Sub input. Furthermore, using the DVI Input, you can receive directly a digital signal of the computer, consequently picture on the screen are much more clear and fresh.
Features
Features
Page 4
FCC RF INTERFERENCE ST
FCC RF INTERFERENCE STAA
TEMENT
TEMENT
NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio, TV technical for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment,
Page 5
Always obey all
safety messages.
•All the safety and operating instructions should be read before the product is operated. If anything strange happens, unplug this product from the wall outlet.
•Do not disassemble or replace any parts of the monitor. Refer to a qualified service personnel for repair.
Safety Precautions
4
W ARNING
You can be killed or seriously injured if you do not follow instructions.
During a lightning storm, or when it is left unattended and unused for a long period of time, unplug it from the wall outlet.
It can result in fire.
When unplugging your monitor, always grip plug firmly and pull straight out from the receptacle.
It can result in fire or electric shock due to damaged power cord.
This product must be properly grounded.
• Improper grounding may cause malfunction or electric shock.
• When proper grounding is not possible, install circuit breaker.
• Do not ground to gas pipe, water pipe, lightning rod, and telephone line.
During a lightning storm, unplug the monitor from the wall outlet, and do not touch the antenna.
It can cause fire or electric shock.
Power
Installation
Do not use this product in the neighborhood of a bath or shower.
It can result in electric shock or fire.
Do not place this monitor on an unstable cart, stand, or table
It may cause the product and cart to overturn, damaging equipment or causing possible injury.
Page 6
5
While Using Monitor
Do not open cover (or back) because high voltage is present within the monitor’s enclosure.
It may cause electric shock.
Never push objects of any kind into this product through openings at the back of monitor.
It may cause fire or electric shock.
No objects filled with liquids, such as vases, shall be placed on the monitor.
Spilled liquids may cause electric shock or fire.
Do not allow children to play or hang on the monitor.
These actions may tip it over, causing personal injury.
Do not place candle or lighted cigarette on the monitor.
If these fall into the inside of the monitor, it may cause fire or explosion.
Do not disassemble batteries, and do not allow children to swallow them.
Heavy metal may contaminate environment, and can be harmful or detrimental to human health. (When children swallow the batteries, go to hospital and consult with a doctor.)
Do not pray water to the monitor or wipe with damp cloth.
It may cause electric shock or fire.
Unplug the monitor from the wall outlet when smoke or strange smell occurs, then refer servicing to a service personnel.
In the case of continuous use, it may cause fire or electric shock.
Page 7
Always obey all
safety messages.
• All the safety and operating instructions should be read before the product is operated.
Safety Precautions
6
Power
Installation
CAUTION
You can be injured or this product or any other your property can be damaged if you don’t follow instructions.
When moving your monitor, remove the power plug, antenna, and cables, and be sure to move it by more than two people..
Failure to follow this instruction can result in electric shock or personal injury.
Do not touch the power plug with wet hands when plugging or unplugging.
It can result in a risk of electric shock.
Do not install the product where it will be exposed to the direct sunlight, and the product should not be near heat sources such as radiators, stoves, etc.
It may cause malfunction.
Do not install where there is oil, smog, moist, and dust
It may cause malfunction.
For proper ventilation, separate the product from the wall, and keep a distance of more than 4”.
Due to the increase of temperature inside the Monitor, it may cause fire.
Do not place the monitor where ventilation is not ensured.
Due to the increase of temperature inside the Monitor, it may cause fire.
If you wish to install this product on the wall or ceiling, refer to the professional.
Failure to do so may cause damage to product and injury to human.
When using an outside antenna system, do not install it in the vicinity of overhead power lines.
When antenna touches such power lines, it may cause electric shock.
Page 8
77
During Use
Do not wipe the monitor using a cloth damped with chemicals (benzene, thinner, etc.).
Monitor appearance may be marred. (Unplug the power plug and wipe with soft cloth.)
Do not place the monitor near magnetic, speakers, or telephones.
It can cause a change in the color tone of the screen.
Do not place any object or cover on the monitor.
In an event of improper ventilation, the monitor will be overheated causing fire.
Do not place heavy objects or heat sources on the power cord.
It may damage the power cord, causing fire or electric shock.
When watching the TV, the distance between the Monitor screen and your eye should be as 5~7 times as the diagonal distance of the Monitor.
Watching the TV for a long time may hurt your eye sight.
When cleaning of the inside of the monitor is required, consult to the qualified service personnel.
When the monitor is not cleaned for a long period of time, dust in it may cause fire or malfunction.
When the monitor is placed on a cart or table, the front side of the Monitor should not project outward.
Unbalance may cause the monitor to drop, resulting in personal injury or equipment malfunction and damage.
Do not grip speakers when moving the monitor attached with speakers.
When moving the monitor while gripping speakers, speakers may be fallen away from the monitor due to its weight, causing personal injury.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent ghost image to remain on the Wide Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
Warranty does not cover any damage caused by image retention.
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit.
Page 9
8
INPUT SELEC
T
POW
E
R
D
IS
PLAY
ZOOM
-
P
IC
TU
R
E
M
O
D
E
S
C
R
EEN
M
O
D
E
F
R
EE
Z
E
M
U
T
E
S
O
U
N
D
M
O
D
E
S
L
EEP
ZO
O
M
+
M
ENU
VO
LV
OL
Remote Control
1 UNIT
Audio Cable
1UNIT
PC(15pin) Cable
1 UNIT
A/V Cable
2 UNITS
Note
Check to be sure that the following items are packed with your Plasma pannel.
Checking Accessories
Supplied Accessories
AC Cable 1 UNIT
Page 10
9
Note
The following items are optional accessories. Refer purchasing optional accessories from
Daewoo Electronics Local Dealer or the dealer from where you purchased the unit.
Optional Accessories
DP-SP50
-
Speaker Main Unit Dimension : 4.33(W) x 29.06(H) 3.39(D)inch
-
Including Speaker Stand Dimension : 7.95(W) x 32.91(H) x 7.95(D) inch
-
Audio Amplifier : 8W + 8W
-
Impedance : 8
-
Weight : 9.11Lbs
DP-ST50
-
Dimension : 31.5(W) x 13.9(H) x 16(D)inch
-
Weight : 14.77Lbs
DP-HG30
Variable Angles : 0º, 10º, 15º, 20º, 25º
Speaker Main Unit
Dimension : 25.63(W) x 16.54(H) x
1.5(D)inch Including Stand
Weight : 10.8Lbs.
Wall Mounting Unit
Table Top Stand
Speakers
Page 11
Page 12
11
4 • Safety Precautions 12 • Panel Controls 13 • Remote control
PREPARATION
BASICS
14 • Installation Instructions 15 • Connecting Speaker to PDP
CONNECTION
16 • Watching Digital Broadcasts 18 • Watching Cable Broadcasts 20 • Watching Satellite Broadcasts 22 • Watching a DVD Image 24 • Watching a VCR Image 26 • Watching a Camcorder/Game Console Image 28 • Connecting PC(15pin D-sub) 30 • Connecting PC(DVI)
APPLICATION
33 • Selecting Auto Picture Mode 36 •
Adjusting Screen Size 38 • Adjusting Screen Position and Size 40 • Enlarging Screen Size 42 • Watching a Still Image 43 • Adjusting Auto Sound Mode 44 • Customizing Sound Mode 46 • Selecting INPUT SIGNAL 48 • Checking the Current Input Signal 49 •
Selecting MENU Background Screen and Languages 51 • Select Image Sticking Minimization 53 • Setting Sleep Timer
MISC.
54 • Before Requesting Service 55 • SPECIFICATIONS
CONTENTS
Page 13
Panel Controls
12
Front Panel, Back Panel, Remote Control
*
Parts having same names in Plasma Display and Remote Control would function in exactly the same way.
Front
Rear
Power
Power control sensor
Power Standby: Red - Standby
Green - ON
Power button
DVI-D INPUT
External Speaker
PC INPUT COMPONENT A/V jacks
(DTV/DVD INPUT jacks)
Used when manufacturing(For manufacturer use only)
Power
Select when adjusting volume or select/adjust “MENU.”
Press when moving “MENU.”
STAND BY/OPERATE
S-VIDEO, A/V INPUT, Cable Receiver INPUT jacks
Page 14
13
Remote Control
When Using Remote Control:
Be sure not to allow the Remote Control to drop or to become wet.
Keep it away from hot or moist locations.
Installing the Batteries in your Remote Control:
To remove the cover, slide it outwards while pressing it down.
Place two batteries in the remote control by properly orienting them, then close the cover.
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Input Select button
Used to select a desired input. Every press of the button cycles through the five different modes: Video 1 --> Video 2 -->PC --> DVI --> Component 1 -->Component 2
Used to zoom the screen. To enlarge, press the (+) button, and to return to the previous condition, press the (-) button. (ZOOM Mode: Zoom 0~20)
Select Menu by pressing (Up), (Down), (Left), (Right) buttons.
Every press of the button cycles through the four different modes: Normal -->Dynamic --> Cinema --> User.
Every press of the button cycles through the five different modes: Normal -->Movie --> Music -->News -->User.
Mutes sound.
Pressing the Power button of the Monitor allows the Display to be standby. (Red light is shown in the Remote Control Sensor.) At this time, if you press the Power button of the Remote Control, the Display is turned ON (Green light in the Sensor).
Indicates the current state and resolution.
Used to display a desired menu.
Adjusts the volume.
Adjusts the size of the screen (normal, 16:9, etc.)
Used to view a still picture during watching moving images. (Sound can be heard.)
Each time you press this button, a different input mode appears. The sequence is as follows:
15 Min. -->30 Min. -->60 Min. -->90 Min. -->120 Min. -->OFF
After the time is selected, it automatically becomes stand-by state.
46
34
Menu Select button
40
Screen Select button
33
Sound Mode button
43
Mute button
Aspect Ratio
36
Still
42
Sleep Timer
51
Power button
16
Display button
48
ZOOM button
Menu button
44
Volume button
34
Note
• Use two “AAA” batteries.
• Be sure to use replacement batteries of the same type as the original ones.
• The life of a battery depends on how much it has been used.
*
The number in
()
indicates the page in which
the function of each button is explained in detail.
Page 15
14
Installation Instructions
When Using the Stand
(Assembled Picture)
M6 SCREWS
Take out the STAND from the package.
1
Engage the assembled stand with 6 screws (M6) enclosed.
3
Smoothly fit the Stand to the Plasma Display Panel
2
Erect the Display
4
*
When installing PDP Main Unit, be sure it is done by more than 2 professionals.
*
For detailed installation information, refer to the User’s Manual, “STAND”.
Page 16
15
UNINSTALLING SPEAKERS FROM ITS OWN STAND.
1
Connecting the Speaker Cable
2
• Connect one set (two cables) of the cable to the terminals on the back of the speaker in the way that red cable is for (+) terminal and black cable for (–) terminal.
Connecting the Speaker to the PDP
.
Please, use a coin to loosen the special screws.
Stand
Speaker
Page 17
Watching Digital
Broadcasts
• To watch digital broadcasts:
- Purchase a separate
digital Broadcasting Receiver(SET-TOP BOX)
- Connect the PDP to a
Cable Broadcasting Receiver that is provided by a company which re­transmits digital broadcasts.
16
Watching Digital Broadcasts
Press the Power Buttons
• Press the Power buttons of the PDP and the Receiver.
2
Connect a Digital Broadcasting Receiver to the PDP
• Prepare A/V Cables supplied.
• Connect the cables from the Digital TV Receiver output terminal to the PDP(Component 1, 2) input terminal.
• When connecting the cables, be sure to match the cable colors.
1
DTV/DVD INPUT
L- AUDIO -R
Video
Digital Broadcasting Receiver
(Set-T op Box)
Audio
Page 18
17
Input Select
INPUT
SELECT
• Select [Component 1 or Component 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit.
• Each time you press the INPUT SELECT button, different input modes appear. The sequence is as follows: Component 1 --> Component 2 -->Video 1 -- >Video 2 -- >PC
--> DVI.
Select a Desired Channel and Function
• Select a desired channel and function by using the Remote Control of Digital Broadcasting Receiver.
3
4
NOTES:
1) You can select INPUT SELECT while you are using OSD(Menu). Sequence: [Menu] -->[Input] --> [Component 1 or 2 (DTV/DVD)]
2) Digital Broadcasting signals available: 1080i, 720p, 480p, 576p.
3) Antenna Connection: Apartment : Check if community antenna receives digital broadcasts. Private Houses: Set the indoor/outdoor UHF antenna to the direction of the digital broadcasting transmitting company.
4) For detailed connection method, refer to the Owner’s Manual of Digital Broadcasting Receiver.
5) What is a component? : Signal with which brightness and color signals are separated, producing a sharp screen.
6) If the Digital Broadcasting Receiver has PC Output terminal or DVI Output terminal, connect to ‘PC INPUT’ or ‘DVI INPUT’ at the back panel of the PDP. When watching the PDP by PC or DVI Input, some undesired signals may be seen at the top and bottom area of the screen. In this case, select [Menu] -->[Screen] --> [Vertical Size] to adjust.
Component1
PC
DVI
Component2
Video1
Video2
Page 19
Watching Cable
Broadcasts
• To watch cable broadcasts, subscribe to your local Cable TV Broadcasting, and then, connect the digital set-top box for cable TV to the PDP as shown below.
Watching Cable Broadcasts
18
Press the Power Buttons
• Turn the PDP and the Receiver ON.
2
Connect a CABLE Broadcasting Receiver to the PDP.
• Prepare the A/V cable.
• Connect the receiver(Output) to PDP(Video Input) as shown below .
• When connecting to an external A V source, be sure to match the colors.
1
VIDEO INPUT
L- AUDIO -RVIDEO
S-VIDEO
Video/Audio
Cable Broadcasting Receiver
Page 20
19
Input Select
INPUT
SELECT
• Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit.
• Each time you press the INPUT SELECT button, different input modes appear. The sequence is as follows: Video 1 -->Video 2 -->PC --> DVI -->Component 1 --> Component 2.
Select a Desired Channel and Function
• Select a desired channel and function by using the Remote Control of the Cable Broadcasting Receiver.
3
4
NOTES:
1)
If your local cable company re-transmits digital broadcasts, you may watch normal broadcasts and digital broadcasts simultaneously. For detailed information, refer to your local cable company.
Video1 Video2 PC
Component1 DVIComponent2
Page 21
Watching Satellite
Broadcasts
• To watch satellite broadcasting, subscribe to a Digital Satellite Broadcasting, then connect the digital set-top box for satellite broadcasting to the PDP as shown below.
Watching Satellite Broadcasts
20
Press the Power Buttons
• Turn the PDP and the Receiver ON.
2
Connect a Satellite Broadcasting Receiver to the PDP.
• Prepare the A/V cable.
• Connect the receiver(Output) to PDP(Video Input) as shown below .
• When connecting to an external AV source, You have to connect to the same color A V source.
1
VIDEO INPUT
L- AUDIO -R
Comp. VIDEO
S-VIDEO
Video/Audio
Satellite Broadcasting Receiver
Page 22
21
Input Select
INPUT
SELECT
• Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or PDP unit.
• Each time you press INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 --> Video 2 -->PC --> DVI -->Component 1 --> Component 2.
Select a Desired Channel and Function
• Select a desired channel and function by using the Remote Control of the Satellite Broadcasting Receiver.
3
4
NOTES:
1)
Picture quality of the Digital Satellite broadcasts is SD grade, and its aspect ratio is 16:9.
Video1 Video2 PC
Component1 DVIComponent2
Page 23
Watching a DVD
Image
• Component Input is set to 480i and 480p mode.
• Connect the cable from the DVD Video Output (Y, Pb/Cb, Pr/Cr) to the Component Input at the back of PDP, and connect the cable from DVD Audio output (Left, Right) to the Audio Input at the back of PDP.
Watching a DVD Image
22
Press the Power Buttons
• Turn the PDP and the DVD ON.
2
Connect a DVD Player to the PDP.
• Prepare the A V cable.
• Connect the DVD(Output) to the PDP(Component or Video Input) as shown below .
• When connecting to an external A V source, match the colors.
1
Video
DVD DVD
Video/ Audio
S-
Video
Audio
Page 24
23
Input Select
INPUT
SELECT
• Select [Component 1 or Component 2, Video1, Video2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit.
• Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Component 1 --> Component 2 -->Video 1 -- >Video 2 -- > PC
--> DVI
.
Select a Desired Title and Function
• Select a desired title and function by using the Remote Control of the DVD.
3
4
NOTES:
1) Y/Cb/Cr, which stands for DVD Player’s Output Terminal, can also be written as Y/B-Y/R-Y, Y/Pb/Pr depending on the kinds of DVD devices.
2) The way of connecting the DVD to the PDP is as follows:
Y <---> Y Cb <---> Pb, B-Y, Cr <---> Pr, R-Y
3) The DVD output can be made by Video, S-Video and/or Component Video depending on the DVD devices. There are various output modes, so be sure to check when to purchase it.
4) When connecting S-Video and Video simultaneously, only S­Video will be displayed on the screen.
Component1
PC
DVI
Component2
Video1
Video2
Page 25
Watching a VCR Image
• Video can use either the video terminal or the S-video terminal.
Watching a VCR Image
24
Press the Power Buttons
• Turn the PDP and the VCR ON.
2
Connect a VCR to the PDP.
• Prepare the AV cable.
• Connect the Video(Output) to PDP(Video Input) as shown below.
1
VIDEO INPUT
L- AUDIO -R
Comp. VIDEO
S-VIDEO
S-Video
VCR
Video/Audio
Page 26
25
Input Select
INPUT
SELECT
• Select [Video 1 or Video 2] by pressing the INPUT SELECT button of Remote Control or PDP unit.
• Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 -->Video 2 --> PC -->DVI
-->
Component 1 --> Component 2.
Select a Desired Title and Function
• Select a desired title and function by using the Remote Control of the VCR.
3
4
NOTES:
1) When connecting a Video, the S-Video terminal provides a better image than the Video terminal.
2) When connecting to the Video terminal, connect 3 color AV cables (video, left audio, right audio) to the PDP; for the S­Video terminal, connect the Audio terminal (Left, Right) in the same way, and connect the Video terminal by the S-Video cable (sold separately).
3) When connecting the Video terminal and the S-Video simultaneously, the S-Video terminal is selected. This can be checked by the [Display] button of the Remote Control.
Video1 Video2 PC
Component1 DVIComponent2
Page 27
Watching a
Camcorder/Game
Console Image
• Enjoy images recorded by camcorder or the game console after connecting to the PDP.
W atching a Camcorder/Game Console Image
26
Press the Power Buttons
• Turn the PDP and the Camcorder/Game Console ON.
2
Connect a Camcorder/Game Console to the PDP.
• Prepare the AV cable.
• Connect the Video(Output) to the PDP(Video Input) as shown below.
• When connecting to an external AV source, match the colors.
1
VIDEO INPUT
L- AUDIO -R
Comp. VIDEO
S-VIDEO
Video/Audio
Game Console/Camcorder
Page 28
27
Input Select
INPUT
SELECT
• Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit.
• Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 -->Video 2 --> PC --> DVI -- >Component 1 -->Component 2.
Select Function
• Select the Function by using the Remote Control of Camcorder or Game Console.
3
4
NOTES:
1) When connecting a Video, the S-Video terminal provides a better image than the Video terminal.
2) When connecting to the Video terminal, connect 3 color AV cables (video, left audio, right audio) to the PDP; for the S­Video terminal, connect the Audio terminal (Left, Right) in the same way, and connect the Video terminal by S-Video cable(sold separately).
3) When connecting a component, refer to “Wattching a DVD Image” on page 22-23.
Video1 Video2 PC
Component1 DVIComponent2
Page 29
Connecting PC
• DAEWOO PLASMA supports resolution of VGA, SVGA, XGA, SXGA, UXGA.
• Before connecting a PC to the PDP, be sure to adjust the resolution of PC.
Connecting PC(15pin D-sub)
28
Connect the PC to the PDP.
• Prepare the PC cable (D-sub 15pin) and the PC audio cable(Sold seperately).
• Connect the PC(Output) to the PDP(Input) as shown below.
2
Before connecting to the PDP, set the resolution of the PC.
• Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen.
• Choose the SETTINGS tab in the DISPLAY Menu.
• In the SETTINGS Menu, select 1024 x 768.
1
PC INPUT
L
R
AUDIO
15 PIN D-subAudio
PC
Page 30
29
Input Select
INPUT
SELECT
• Select [PC] by pressing the INPUT SELECT button of the Remote Control or PDP unit.
• Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows:
PC --> DVI --> Component 1 --> Component 2 -->Video 1 -->Video 2.
Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or Mouse.
4
5
Press the Power button.
• Turn on the PDP and the PC.
3
NOTES:
1) The resolution of the PC monitor is best at 1024 x 768 (XGA).
2) If there is a [Vertical Frequency]setting menu in the [Display] Menu of the PC, adjust the frequency to 60Hz.
3) If the PC resolution is too high, it may be hard to read letters. Select a suitable resolution.
PC
Component1
DVI
Component2Video1Video2
Page 31
Connecting PC
• DAEWOO PLASMA supports resolution of VGA, SVGA, XGA, SXGA, UXGA.
• Before connecting a PC to the PDP, be sure to adjust the resolution of PC.
• This product is not supported by Plug and Play, so select Standard Monitor when setting PC monitor.
Connecting PC(DVI)
30
Connect the PC to the PDP.
• Prepare the DVI cable and the PC audio cable(Sold seperately).
• Connect the PC(Output) to the PDP(Input) as shown below.
2
Before connecting to the PDP, set the resolution of the PC.
• Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen.
• Choose the SETTINGS tab in the DISPLAY Menu.
• In the SETTINGS Menu, select 1024 x 768.
1
DVI-D INPUT
L
R
AUDIO
DVIAudio
PC
Page 32
31
Input Select
INPUT
SELECT
• Select [DVI] by pressing the INPUT SELECT button of the Remote Control or PDP unit.
• Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: DVI --> Component 1 --> Component 2 --> Video 1 - - >Video 2 - - >PC.
Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or Mouse.
4
5
Press the Power button.
• Turn on the PDP and the PC.
3
NOTES:
1) The resolution of the PC monitor is best at 1024 x 768 (XGA).
2) If there is a [Vertical Frequency]setting menu in the [Display] Menu of the PC, adjust the frequency to 60Hz.
3) If the PC resolution is too high, it may be hard to read letters. Select a suitable resolution.
4) DVI input port receive only Digital Signal.
5) Depending on the graphic card when plug & unplug the DVI connection the screen may not display correctly. Restart the computer if this happen.
DVI
Component2Component1
Video1Video2PC
Page 33
32
PC and DVI Input Resolution Available in PDP
• According to the kind of graphic card, there is no picture of pc input and some problems like line noises can happen in picture. If these problems happen, ask to a graphic card company.
Resolution
Horizontal Frequency(KHz) Vertical Frequency(Hz) Remark DVI PC
31.469
37.861
24.823
30.48
31.469
37.861
31.469 35
37.861
37.5
39.375
43.269
31.47
31.469
37.927
31.54
15.63
35.156
35.16
37.879
48.077
46.875
53.674
49.726
48.193(48.077)
48.363
53.95
56.476
60.241
60.023
68.677
80.66
70.84 54
63.851
67.5
77.094
61.796
71.713 45 60 75
85.938
46.433
63.981
70.66
74.88
78.125
78.855
79.976
81.13
91.416
62.5 75
81.25
87.5
93.75 100
640x350
640x400
640x480
720x400
720x480 720x576
800x600
832x624
1024x768
1152x864
1152x900 1280x720
1280x960
1280x1024
1600x1200
70.1
85.1
56.4
60.0
70.1
85.1
59.9
66.7
72.8
75.0
75.0
85.0
60.1
70.1
85.1
60.0
25.0
56.3
57.2
60.3
72.2
75.0
85.1
74.0
59.3(59.8)
60.0
66.1
70.1
74.9(74.6)
75.0
85.0
100.0
84.0
60.0
70.0
75.0
85.0
66.0
76.0
60.0
60.0
75.0
85.0
43.4
60.0
66.5
70.0
72.0
74.0
75.0
76.1
85.0
48.0
60.0
65.0
70.0
75.0
80.0
O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
O O O O
O
O
O
O O O O O
O
O
O
O
O
O O
O
O O
O
IBM
VESA
NEC PGA
IBM (DOS)
VESA
DOS
Macintosh
VESA VESA
IBM
VESA
VGA
IBM
VESA
480P
PAL VESA VESA VESA VESA VESA VESA
Macintosh
Macintosh (OAK)
VESA
XGA
HP & VESA
Macintosh
VESA VESA
Fujitsu
SUN
VAX VESA VESA VESA
SUN SUN
720P VESA VESA VESA VESA VESA
VAX
NEC
HP & HITA
Sony & NEC
VESA
SUN VESA VESA VESA VESA VESA VESA VESA
Page 34
Selecting Picture
Mode
• Select the Picture modes that are appropriately set depending on the kinds of pictures, and enjoy them.
Selecting Picture Mode
PICTURE
MODE
• Press the [PICTURE MODE] on the Remote Control.
• Pressing the [PICTURE MODE] first time will display the current PICTURE MODE.
Each Press of the Button Will Select One of Four Picture Modes.
• Each time you press the button, a different Picture mode appears. The sequence used is as follows:
* Normal : For a highly defined image in a normally bright
room
* Dynamic: For a clear-cut image emphasizing high contrast
for sports viewing * Cinema: For a movie * User: Allows the user to customize settings as desired.
Menu on the Screen Will Disappear .
• After selecting a desired Picture mode, the menu on the screen will disappear.
• Normal, Dynamic, and Cinema Modes are factory preset values.
If you want to customize the Picture modes, refer to the following page.
3
1
2
Selecting Picture Mode
33
NOTES:
1) Normal, Dynamic, and Cinema Modes are factory preset values.
2) When adjusting sub-menus while you are in Normal, Dynamic, and Cinema Modes, the Picture Mode will be automatically converted to User Mode, and the adjustments will be made.
3) Pressing of the [INITIALIZATION] button in the [Utility] Menu will allow for the Brightness, Contrast, etc. to return to the factory preset values.
4) The SHARP Menu adjusts the picture sharpness.
5) Adjusting the Color Temperature makes the mood warm or cold.
PICTURE
MODE
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Normal Dynamic
Cinema User
Page 35
Customizing
Picture
• You can adjust the color tone and brightness to your preference.
Customizing Picture
34
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Press the / Button.
• After selecting [Picture] by the / buttons, press the button that will display the following.
Select the Custom Mode.
• Select [User] by the / buttons.
3
Press the MENU Button.
• The MENU shown below will display on the screen.
1
2
MENU
Picture
Sound Screen Utility Input
Mode Brightness Contrast Color Tint Sharpness Color Temp.
Normal
Normal
Move
Picture
VOLVOL
Sound Screen Utility Input
Mode
Brightness Contrast Color Tint Sharpness Color Temp.
Move
Previous
Select
Normal
Normal
Previous
Adjust
Picture Sound
VOLVOL
Screen Utility Input
Mode
Brightness Contrast Color Tint Sharpness Color Temp.
Move
User
Normal
Previous
Adjust
Page 36
Select User Mode Adjustments
Picture Condition Adjustments
• Press the / buttons to adjust the picture at your preference.
4
5
35
• While you are in [Picture Mode – User], press the / buttons to select a specific adjustment item.
NOTES:
1) While you are in the PC or DVI INPUT mode, you can only adjust brightness, contrast, sharpness and color temperature.
2) When you adjust Brightness, Contrast, Color, Tint in DTV mode or adjust Brightness, Contrast in PC or DVI mode, the picture is adjusted finely.
3) The adjusted values are memorized in each mode seperately.
4) The Tint control is used only when the input signal is NTSC If input signal is NTSC, Tint control is displayed in picture menu.
VOLVOL
VOLVOL
Picture Sound Screen Utility Input
Mode
Brightness
Contrast Color Tint Sharpness Color Temp.
Move
User
Normal
Previous
Adjust
Picture Sound Screen Utility Input
Mode
Brightness
Contrast Color Tint Sharpness Color Temp.
User
Normal
Move
Previous
Adjust
Page 37
Adjusting
Screen Size
• You can adjust screen size or aspect ratio as desired.
Adjusting Screen Size
36
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Press the SCREEN MODE Button.
• Each time you press the SCREEN MODE button on the Remote Control, a different SCREEN MODE appears. The sequence used is as follows:
• The MENU shown below will display on the screen.
1
SCREEN
MODE
Enlarge LBS
Normal
16:9
Panorama
Enlarge LB
NOTES:
1) When the INPUT SIGNAL is DTV [in COMPONENT 1 or COMPONENT 2], only the aspect ratios of 16:9 and 4:3(Normal) will be applied by Input signal. Etc) If input signal is 16:9, PDP displays in 16:9 mode.
2) The digital broadcasting (720p, 1080i) is fixed at the aspect ratio of 16:9.
3) Displaying a picture in a normal mode (4:3) for a long time may cause phosphor of the PDP to be burned. So avoid displaying a picture in 4:3 screen size for a long time.
4) 16:9 : Theater-like 16:9 picture formats Panorama : 16:9 picture formats with panorama effect Normal : Displays pictures of original picture size. Enlarge LB : Enlarges the screen as to fill the black part of
up and down.
Enlarge LBS: Enlarges the screen, and shifts up as to see
the subtitles in case you are watching video with subtitles.
Page 38
37
Press the MENU Button.
• Press the [MENU] button on the Remote Control.
Select “Screen”.
• Press the Channel / buttons to select “Screen.”
Select the Screen Size.
• Press the V olume / buttons to select “Screen Size”.
3
1
2
Adjusting from
MENU Screen
• Available Screen Mode
Input Available Mode PC,DVI None Component 16:9, Normal
(480p or above)
Video 1 16:9, Video 2 Panorama Component Normal
(480i)
Enlarge LB Enlarge LBS
MENU
Picture
Sound Screen Utility Input
Mode Brightness Contrast Color Tint Sharpness Color Temp.
Move
Normal
Normal
Previous
Select
VOLVOL
Picture Sound
VOLVOL
Screen Utility Input
Picture Sound
Screen
Utility Input
Mode Normal
Move
Mode Enlarge LB
Previous
Select
Move
Previous
Adjust
Page 39
Adjusting Screen
Position and Size
• You can adjust the screen position and size as desired.
• This function is only used when adjusting the screen position and size on the PDP monitor by using the PC or DVI input signal.
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
ZOOM+
MENU
VOL VOL
Press the MENU Button.
• The MENU screen as shown below will appear.
Press the / Button.
• Press the / buttons to select ‘Screen’.
1
2
38
Adjusting Screen Position and Size
MENU
VOLVOL
Picture
Sound Screen Utility Input
Mode Brightness Contrast Sharpness Color Temp.
Move
Normal
Normal
Previous
Select
Picture Sound
Screen
Utility Input
H. Size V. Size H. Position V. Position Phase Frequency
Move
Previous
Select
Page 40
39
Press the Volume / Buttons.
• Press the Volume / buttons to select “Screen”.
• While you are in ‘Screen’ mode, press the or button to select a desired item, and
then, adjust the value by pressing the or .
3
NOTES:
1) Horizontal/Vertical size and position values can be adjusted only in the [PC] or [DVI] input mode.
2) H. Size: As the value increases, the screen width increases
3) V. Size: As the value increases, the screen height increases.
4) H. Position: Increasing value moves screen to the right. As the value increases, the screen moves to the right.
5) V. Position: Increasing value moves screen up. As the value increases, the screen mores up.
6) Phase: When there are zitter or blurring in image, adjust this value.
7) Frequency: When there are zitter or blurring in image, adjust this
value.
VOLVOL
Picture Sound Screen Utility Input
H. Size
V. Size H. Position V. Position Phase Frequency
Move
Previous
Adjust
Page 41
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Press the ‘ZOOM+’ Button.
• Press the ‘ZOOM+’ button to show currently selected screen size.
• Each time you press the ‘ZOOM+’ button, the screen size will increase stepwise in 0 ~ 20 scale.
• To reduce the screen size, press the [ZOOM-] button.
1
40
Enlarging
Screen Size
• You can view enlarged size of the screen with this function
Enlarging Screen Size
Zoom Level 0
ZOOM+
Zoom Level 0
Zoom Level 5
Zoom Level 10
Zoom Level 15
Zoom Level 20
Page 42
Move the Screen Position.
• While you are in the ‘Zoom’ mode, press the / , / buttons to move screen stepwise up/down,
left/right, respectively .
2
41
NOTES:
1) When the screen is enlarged, the pixel of the screen can become thick and dim.
2) When only subtitle of zoom level remains, you can scroll the image. If subtitle of zoom level disappears, press zoom key, and scroll the image.
3) You can enlarge the screen on freeze mode.
Zoom Level 6
VOLVOL
Page 43
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Press the ‘FREEZE’ Button.
• If you wish to freeze a picture, press the ‘FREEZE’ button. Y ou can still hear the sound.
• Press FREEZE button to cancel the ‘FREEZE’ function.
• To view the enlarged images, press the [ZOOM+] button.
1
FREEZE
42
Watching a
Still Image
• You can view still images temporarily with this function. However, displaying the same images such as still images for a long time may cause image sticking.
Watching a Still Image
NOTES:
1) Displaying the same images such as still images for a long time may cause image sticking (after-image lagging).
2) In this case, such “image sticking” may become less noticeable if moving images are later displayed for a long time.
3) However, an image sticking may become a permanent one, damaging the Plasma Display; therefore, avoid displaying the same images for a long time.
4) Use the function [ISM], while displaying still images for a long
period of time to minimize this effect.
Freeze
Zoom Level 7
Move the Screen Position.
• While you are in ‘FREEZE’ mode, press the / , / buttons to move screen stepwise up/down and
left/right.
2
VOLVOL
Page 44
Adjusting Auto
Sound Mode
• Enjoy various sound modes by selecting your favorite Sound Mode depending on the kinds of moving pictures.
Adjusting Auto Sound Mode
43
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Select SOUND Mode.
SOUND
MODE
• Press the [SOUND MODE] on the Remote Control.
• Press of the [SOUND MODE] for the first time will display the current SOUND MODE.
Every Press of the Button Changes Modes.
SOUND
MODE
• Each time you press the button, a different sound mode appears. The sequence used is as follows:
* Normal : Suitable for watching any motion picture * Movie : Select this mode to simulate being at a movie theater * Music : Ideal for listening to music * News : Allows human voice to be heard more clearly * User : Allows the user to adjust as desired.
MENU will Disappear .
• After selecting a desired SOUND Mode, on-screen menu will disappear in about 2~3 seconds.
• Normal, Movie, Music, News Modes are factory preset values.
If you want to customize the sound modes at your preference, refer to the following page.
3
1
2
Normal Movie
Music UserNews
Page 45
Customizing Sound Mode
• This feature allows the user at adjust at his preference.
Customizing Sound Mode
44
Press the / Button.
• Select [SOUND] by the / buttons, then press the button to display the following.
Select SOUND BALANCE.
• Select [SOUND BALANCE] by the / buttons, then adjust it.
• Sound balance is best at ‘0’.
• Sound Balance: Adjusts sound balance of left and right speaker.
3
Press the MENU Button.
• The MENU Screen as below will be displayed.
1
2
MENU
Picture
Sound Screen Utility Input
Mode Brightness Contrast Color Tint Sharpness Color Temp.
Normal
Normal
INPUT
SELECT
ZOOM
DISPLAY
-
MENU
POWER
ZOOM+
Move
Picture
VOLVOL
Sound
Screen Utility Input
Balance Spatial Effect Sound Mode
Move
Previous
Select
Off
Normal
Previous
Select
VOL VOL
PICTURE
MODE
MODE
FREEZE
MUTESOUND
SCREEN
MODE
SLEEP
VOLVOL
Picture Sound Screen Utility Input
Balance Spatial Effect Sound Mode
Move
Off
Normal
Previous
Adjust
Page 46
Select the Spatial Effect Mode.
• Select Spatial Effect by pressing the / buttons, then select ON/OFF by pressing the button.
• Spatial Effect: Used to feel grotesque by emphasizing stereo effect.
Select the SOUND Mode.
4
5
45
• Select the Sound Mode by pressing the / buttons, then adjust it by pressing the / buttons.
* Normal : Suitable for watching any motion picture * Movie : Select this mode to simulate being at a movie
theater * Music : Suitable for listening to music * News : Allows human voice to be heard more clearly * User : Allows the user to adjust as desired.
NOTES:
1) Custom Mode : Used as an Equalizer with which the user can adjust the sound frequency as desired.
2) If you modify the sound frequency in auto Sound Mode (News, Movie, Music, etc.), it is automatically switched to the User Mode.
3) Low sound is emphasized as the frequency is lowered to 120 Hz, and high sound as raised to 10 KHz.
4) When INPUT is MONO and if you make connection to the Left Audio Input, you can hear from both speakers.
VOLVOL
VOLVOL
Normal Movie
Music UserNews
Picture Sound Screen Utility Input
Balance
Spatial Effect
Sound Mode
Move
Picture Sound Screen Utility Input
Balance Spatial Effect
Sound Mode
On
Normal
Previous
Adjust
Off
Normal
Move
Previous
Adjust
Page 47
INPUT SIGNAL
• Used to select INPUT signal of external device connected to the PDP.
Selecting INPUT SIGNAL
46
Press the INPUT SELECT Button.
INPUT
SELECT
• Press the [INPUT SELECT] button on the Remote Control or the PDP Display to select [COMPONENT 1] or [COMPONENT 2].
• Each time you press the [input select] button, a different screen mode appears. The sequence used is as follows: COMPONENT 1 --> COMPONENT 2 -- >VIDEO 1 - -> VIDEO 2
--> PC --> DVI
1
NOTES:
1) If an external device is not connected or INPUT signal is not applied, Warning Message (“No Signal”) would be displayed.
2) In this case, check if external device is connected and/or terminal connection is properly done.
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
PC
Component1
PC
DVI
Component2
Video1
Video2
Page 48
47
Press the MENU Button.
MENU
• Press the [MENU] button on the Remote Control.
1
Adjusting from the
MENU Screen
Select INPUT.
• Select [INPUT] by the / button.
Select INPUT SIGNAL.
• Select [INPUT SIGNAL] by the / buttons, then press the button.
3
2
Picture
Sound Screen Utility Input
Mode Brightness Contrast Color Tint Sharpness Color Temp.
Normal
Normal
VOLVOL
Picture Sound Screen Utility
Input
Move
Previous
PC
DVI Component 1 (DTV/DVD) Component 2 (DTV/DVD)
Video 1 Video 2
Move
Select
Previous
Select
VOLVOL
Picture Sound Screen Utility Input
PC
DVI Component 1 (DTV/DVD) Component 2 (DTV/DVD)
Video 1 Video 2
Move
Previous
Select
Page 49
Checking the
Current Input Signal
• Used to check the INPUT signal mode, resolution, frequency, etc. of the current screen.
Checking the Current Input Signal
48
Press the DISPLAY Button.
DISPLAY
• Press the [DISPLA Y] button on the Remote Control.
1
1. If you watch Digital Broadcasts:
Displays which input terminal is used, and indicates the input signal mode. Indicates the horizontal and vertical resolution of the current INPUT signal. Indicates the frequency of the current INPUT signal.
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
Component 1
1920 x 1080
60 Hz
Component 1
1920 x 1080
60 Hz
2. If you watch DVD image:
Displays which input terminal is used, and indicates the signal mode. Indicates the mode and frequency of the current INPUT signal.
Component 2
YUV 60 Hz
3. If you watch VCR image:
Displays which input terminal is used, and indicates the signal mode. Indicates the mode and frequency of the current INPUT signal.
Video 1
NTSC 60 Hz
NOTES:
1) DAEWOO PLASMA can receive NTSC, PAL, SECAM, etc.
2) “1920 x 1080” displayed in the INPUT signal does not indicate the resolution of the monitor, but the signal that is sent by Digital Broadcasting Receiver.
Page 50
Selecting
Languages
• Used to select transparency of the background screen and language used in MENU.
Press the MENU Button.
MENU
• The MENU screen will be displayed as below.
Press the / Button.
• Select [Utility] by the / button.
Select the MENU BACKGROUND SCREEN.
• Select the MENU [Background Screen] by pressing the button.
• Every press of the button while you are in the[MENU Background Screen] would switch between Transparent/Opaque.
3
1
2
Selecting MENU Background Screen and Language
4949
VOLVOL
Picture
Sound Screen Utility Input
Mode Brightness Contrast Color Tint Sharpness Color Temp.
Move
Normal
Normal
Picture Sound Screen
Utility
Input
Background Language Initialize ISM
Previous
Select
Opaque
English Press key Press key
Move
VOLVOL
Picture Sound Screen Utility Input
Background
Language Initialize ISM
Move
Opaque
English Press key Press key
Previous
Adjust
Previous
Select
Page 51
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
ZOOM+
MENU
VOL VOL
Back to
Initialization
• You can restore the values of the adjustment/setting made in the MENU to factory settings.
Selecting MENU Background Screen and Languages
Select MENU LANGUAGE SELECT by the / Button.
• Select LANGUAGE by the / button.
• Every press of the button while you are in the [LANGUAGE] mode would cycle through the different languages.
INITIALIZATION will Start.
• Select [INITIALIZATION] by the / buttons, then press the button to start initialization.
4
5
50
When [INITIALIZA TION] is completed:
1) When [INITIALIZATION] is completed, those values that have been set in the User Mode of [SCREEN MODE] and [SOUND MODE] will be returned to the factory preset values.
2) When you try to initialize, be advised that you should think it over.
3) The items in the [SCREEN] Menu in PC or DVI INPUT are also initialized (i.e., H. Size, V. Size, H. Position, V. Position, Phase, Frequency, etc.)
4) Language, volume, OSD background, input mode are not initialized.
VOLVOL
VOLVOL
NOTES:
*
When Power is turned ON first time, ‘SELECT LANGAUGE’ Mode will be displayed, then, select a
desired language by button. (Displayed only once)
Picture Sound Screen Utility Input
Background
Language
Initialize ISM
Move
Opaque
English Press key Press key
Previous
Adjust
Picture Sound Screen Utility Input
Background Language
Initialize
ISM
Move
Opaque
English
Press key
Press key
Previous
Adjust
Page 52
51
ISM
• Image sticking minimisation.
• Displaying a still image like PC input for a long time causes part image sticking in the panel
• The ISM function minimise this effect.
Press the MENU Button.
MENU
• The MENU screen will be displayed as below.
Press the / Button.
• Select [Utility] by the / button.
Select the MENU ISM SCREEN.
• Select the MENU [ISM] by pressing the /button.
• Press of the button while you are in the ISM.
3
1
2
Selecting Image Sticking Minimization
Picture
Sound Screen Utility Input
Mode Brightness Contrast Color Tint Sharpness Color Temp.
Move
Normal
Normal
Previous
Select
Picture Sound
VOLVOL
Screen
Utility
Input
Background Language Initialize ISM
Move
VOLVOL
Picture Sound Screen Utility Input
Background Language Initialize
ISM
Opaque
English Press key Press key
Previous
Select
Opaque
English Press key
Press key
Move
Previous
Adjust
Page 53
52
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
ZOOM+
MENU
VOL VOL
Selecting Image Sticking Minimization
Select Functions.
• Every press of the button after select function by the / button would switch between ON/OFF.
4
NOTES:
*
Pixel Shift : The whole screen shifts up/down,
left/right at 10sec interval to minimize image sticking.
*
Low Bright : When displaying a stand picture or
a fixed pattern for a long time, brightness level decreases to minimize image sticking. Return to the original brightness level if picture change or mode off.
*
Image Invert : Displays inverted image.
VOLVOL
Picture Sound Screen Utility Input
Pixel Shift
Low Bright Image Invert
Move
Off Off Off
Previous
Adjust
Page 54
Setting
Sleep Timer
• SLEEP TIMER turns the Monitor off after a preset time.
Press the SLEEP Button.
SLEEP
• Press the [SLEEP] button on the Remote Control.
• Pressing the [SLEEP] button first time will display the current setting for SLEEP TIMER.
• To cancel the SLEEP TIMER, press the [SLEEP] button to select ‘OFF’.
1
Setting Sleep Timer
53
INPUT
SELECT
POWER
DISPLAY
ZOOM
-
PICTURE
MODE
SCREEN
MODE
FREEZE
MUTESOUND
MODE
SLEEP
ZOOM+
MENU
VOL VOL
NOTES:
1) On-screen information disappears if you do not take any action for about two seconds after pressing the SLEEP button.
2) If you turn the Monitor off after setting SLEEP, the setting is erased.
Sleep Timer off
Sleep Timer off
Sleep Timer 15 Minutes
Sleep Timer 30 Minutes
Sleep Timer 120 Minutes
Sleep Timer 90 Minutes
Sleep Timer 60 Minutes
Page 55
Before Requesting Service
54
Before
Requesting for a
Service
St yo mm
ps
C
h e c k s
A
c
t
i o n
• There are empty spots at the top and the bottom area of the screen.
• Check if the screen size of an image is wider than 16:9 aspect ratio (theater screen size).
• When video screen is wider than 16:9 aspect ratio, you may see dark areas at the top and the bottom of the screen.
• The Display makes a snapping sound.
• Check if the pictures and sound are
normal.
• This sound is produced due to
variations in room temperature.
• This sound does not indicate that the
Display has a problem if the pictures and sound can be viewed and heard properly.
• Remote control does not function properly.
• Check for any obstacle between the
Remote Control and the Display.
• Check for dead batteries and
incorrect battery orientation.
• Check if the Remote Control is the
right one.
• Remove any obstacle between the
Remote Control and the Display.
• Replace batteries and use the correct
polarity (+) or (-) of the batteries.
• Use the pertinent Remote Control
proper to the model.
St yo mm
ps
C
h e c k s
A
c
t
i o n
• Screen size is suddenly changed.
• The screen size of a video image
may not be matched to the size of the dark initial screen.
• Check by using other video tape.
• System auto detection.
• If above statement shows while watching, for safety the internal system is automatically detected and PDP will be turn off.
• Please contact nearest Service Center immediately.
• There are spots on the screen or screen rolls.
• Check if your product is affected by
any interference from automobiles, high-voltage transmission lines, neon signs or other potential sources.
Before requesting for a service, check the following points once again.
Because system is unstable
power will be off after 5 seconds.
Page 56
55
SPECIFICA TIONS
In the event that the product has been submerged in the water in rainy season:
Immediately wash it with clean water, and dry it in ashadow place, then call for service from the nearest Daewoo Service Center. Never plug the Power Cord since there is risk of electric shock and damag of the product.
*
Appearance and specifications of this product are subject to change for improving the product without prior notice.
DISPLAY UNIT
Diagonal Size 126cm (50”) Screen Aspect Ratio 16 : 9 Display Resolution 1366(H) X 768(V) dots Pixel Pitch 0.81(H) X 0.81(V) mm Output Color 16,770,000 Colors Video Signal NTSC, PAL, SECAM, P AL-M/N, NTSC4.43 Dimension 48.1 1(W) X 29.06(H) X 3.70(D) inches. Weight 105.8 Lbs Power Requirement AC 100-240V , 50/60Hz
INPUT/OUTPUT TERMINAL
INPUT/OUTPUT ITEMS VIDEO AUDIO
COMPONENT INPUT
DTV/DVD ONLY (LEFT/RIGHT) (Y, Pb/Cb, Pr/Cr), 2 sets 2 sets
EXTERNAL VIDEO INPUT two RCA jacks (LEFT/RIGHT)
INPUT S-VIDEO INPUT two 4 pin Mini DIN jack 2 sets
Computer(PC)
one 15 pin D-sub jack (LEFT/RIGHT) DVI-D(Digital only) 1 set each
AUDIO OUTPUT SPEAKER OUTPUT(sold separately) 16W (two 8W)
Loading...