DVD Recorder + VCR
RV4000
User Manual
POWER
PLAY/PAUSE STOP REW FF DVD• VCR
REC
CH
VCR
EJECT
VCR VCRDVD DVD
ONE-TOUCH COPY
DUAL
RV4000 DVD RECORDER +VCR
DVD
EJECT
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지A
INTRODUCTION
1
Important Safeguards
Important Safeguards
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and servicing instructions in
the literature accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
WARNING:
Do not install this equipment in a confined space such as a bookcase or
similar unit.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to
Article 820-40 of the National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of the cable entry as
practical.
CAUTION:
This DVD Recorder+VCR employs a Laser System. To ensure proper use of this product, please read this
owner’s manual carefully and retain for future reference. Should the DVD Recorder+VCR require maintenance,
contact an authorized service center. Use of controls, adjustments, or the performance of procedures other than
those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do
not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.
CAUTION:
The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as
vases, should be placed on the apparatus.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
CLASSE 1 PRODUIT LASER
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지1
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S
MANUAL AND THOSE MARKED ON THE PRODUCT. RETAIN THIS MANUAL FOR FUTURE
REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in
electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the
following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
2
Important Safeguards
IMPORTANT SAFETY INSTRUCTIONS
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the product is operated in a residential installation. This product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful interference to radio or television reception, which can
be determined by turning the product off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the product and receiver.
- Connect the product into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC COMPLIANCE:
The responsible party for this product’s compliance is: GoVideo, 7835 East McClain Drive, Scottsdale, AZ
85260, USA.
SERIAL NUMBER:
The serial number is found on the back of the DVD Recorder+VCR. This number is for this unit only. You should
record requested information here and retain this guide as a permanent record of your purchase.
Model No. ___________________________________
Serial No. ___________________________________
1 Read these instructions.
All these safety and operating instructions
should be read before the product is operated.
2 Keep these instructions.
The safety, operating and use instructions should
be retained for future reference.
3 Heed all warnings.
All warnings on the product and in the operating
instructions should be adhered to.
4 Follow all instructions.
All operating and use instructions should be
followed.
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지2
INTRODUCTION
3
5 Do not use this product near water.
For example: near a bath tub, wash bowl, kitchen
sink, laundry tub, in a wet basement; or near a
swimming pool; and other areas located near
water.
6 Clean only with dry cloth.
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from overheating.
The openings should never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
8
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatuses (including amplifiers) that produce
heat.
9
Make sure that rating of your household
electricity supply matches that shown on the
back of your product.
10
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11
Only use attachments/ accessories specified by
the manufacturer.
12
Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
apparatus. When a cart is used,
use caution when moving the
cart/ product combination to avoid injury from
tip-over.
13
Unplug this product during lightning storms or
when unused for long periods of time.
14
Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as: Power-supply cord
or plug is damaged; liquid has been spilled or
objects have fallen into the product; the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15
Do not connect the product to the power supply
if you have just moved it from a cold environment
to a warm room. This can lead to condensation
inside the product, which can damage it. Wait
for approx. 2 hrs for it to reach room
temperature.
16
Make sure the product is placed at least 10 cm
apart from other home appliances or obstacles to
ensure sufficient ventilation.
17
This product is designed to work continuously.
Switching if off(stand-by mode) does not
disconnect if from the mains. To disconnect if
from the mains you have to unplug it.
Important Safeguards
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지3
4
Table of Contents
Table of Contents
Important Safeguards _________________________1
Table of Contents ______________________________4
Overview ______________________________________5
Identification of Controls_______________________10
INTRODUCTION
Connecting Antenna/Cable ____________________15
Connecting a TV _______________________________16
Connecting an Amplifier/Receiver _____________18
Connecting Optional Equipment ______________19
CONNECTIONS
Initial Installation ______________________________20
Initial Setup____________________________________22
Setup Menu Overview 22
Menu Navigation 22
INSTALLATION Settings 22
RECORDING OPTIONS Settings 25
LANGUAGE Settings 26
PREFERENCE / Video Settings 27
PREFERENCE / Audio Settings 28
PREFERENCE / Parental Controls 30
Various PREFERENCE Settings 32
System Information 34
Restore Defaults 34
On-Screen Display Overview __________________35
SETUP
DVD Playback _________________________________38
VCR Playback _________________________________41
PLAYBACK
Basic Recording________________________________45
Recording from TV 45
One Touch Record (OTR) 46
Checking the Recording Time 46
To Pause the Recording 46
One Touch Copy - DVD to VHS 47
One Touch Copy - VHS to DVD 48
Timer Recording _______________________________49
Recording from an External Input _____________51
RECORDING
DISC Initialize __________________________________52
Disc Menu _____________________________________52
Editing _________________________________________56
EDITING
Troubleshooting _______________________________58
Technical Specifications ________________________61
REFERENCE
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지4
INTRODUCTION
5
Overview
Overview
DVD, DVD+R, DVD+RW?
What is a DVD?
DVD (Digital Versatile Disc) is a new storage medium that combines the convenience of the compact disc with
the latest digital video technology. DVD video uses modern MPEG2 data compression technology that enables
an entire feature film to be stored on a single five inch disc.
How good is the resolution of DVD compared with VHS?
The razor-sharp digital images have a resolution of more than 500 lines of 720 pixels per line. This is more than
twice as high as VHS and is even better than the laser disc. Its picture quality is easily comparable to the digital
masters produced in recording studios.
What can DVD+RW do?
DVD+ReWritable uses phase change media, the same technology on which rewritable CDs are based. A highperformance laser is used to change the reflective properties of the recording layer; this process can be
repeated more than a thousand times.
What can the DVD+R do?
DVD+R (write-once DVD). Unlike a DVD+RW disc, this disc can only be written to once. If it is not finalized after
a recording, further recordings can be added to it. Old recordings can be later deleted but they can no longer be
overwritten. The deleted recordings (titles) are marked 'deleted title'.
Before this disc can be played in a DVD player, it must be finalized in the DVD Recorder+VCR. Once this process
is complete, no further recordings can be added.
What can my DVD recorder do?
Your DVD Recorder+VCR is a machine for recording and playing back digital video discs with ‘two-way‘
compatibility with the universal DVD video standard. This means:
• existing DVD video discs can be played on the recorder.
• recordings made on your DVD Recorder+VCR can be played on other DVD video players and DVD ROM
drives.
Regional code
If the region number described on the DVD disc does not correspond to the
Region number of this player, the player will not play this disc.
1
ALL
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지5
6
Overview
Disc-related Terms
Title (DVD only)
The main film content or accompanying feature content or music album. Each title is assigned a title reference
number enabling you to locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller than titles. A title is composed of one or several
chapters. Each chapter is assigned a number to enable you to easily locate the chapter you want. Depending on
the disc, chapters may not be labeled.
Track (Audio CD only)
Sections of a picture or a musical piece on an audio CD. Each track is assigned a number, enabling you to easily
locate the track you want.
Which discs you can use
The following discs can be used in your DVD Recorder+VCR for playback and recording:
Playback and recording
DVD+RW (Digital Versatile Disc + ReWritable)
DVD+R (Digital Versatile Disc + Write-Once)
Playback only:
DVD Video (Digital Versatile Disc)
DVD-R (DVD-Recordable) : These discs can only be played back if the recording was made in video mode and
the recording was finalized.
DVD-RW (DVD-Rerecordable) : These discs can only be played back if the recording was made in video mode
and the recording was finalized.
Audio CD (Compact Disc Digital Audio)
Video CD (format 2.0)
Super Video CD
CD-R (CD recordable) Audio/ MP3 contents
CD-RW (CD rewritable) Audio/ MP3 contents
Not all recordable CD may be played by your player.
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지6
INTRODUCTION
7
Overview
Notes for Recording
• The recording times shown are not exact because the DVD Recorder+VCR uses variable bit-rate video
compression. This means that the exact recording time will depend on the material being recorded.
• When recording a TV broadcast, if the reception is poor or the picture contains interference, the recording
times may be shorter.
• The disc which is recorded in high speed (over or equal to 2X speed) may be unrecognized.
• If you record still pictures or audio only, the recording time may be longer.
• The displayed times for recording and time remaining may not always add up to exactly the length of the
disc.
• The recording time available may decrease if you heavily edit a disc.
• When using a DVD+R disc, you can keep recording until the disc is full, or until you finalize the disc. Before
you start a recording session, check the amount of recording time left on the disc.
Recording TV Audio Channels
The DVD Recorder+VCR can record one or two channel audio. For TV broadcasts, this usually means mono or
stereo, but some programs are broadcast with a main and a SAP (Secondary Audio Program) audio channel.
You can record either the main audio or the SAP audio.
Restrictions on Video Recording
• You cannot record copy-protected video using this DVD Recorder+VCR. Copy-protected video includes DVDVideo discs and some satellite broadcasts. If copy-protected material is encountered during a recording,
recording will pause or stop automatically and an error message will be displayed on-screen.
• Video that is ‘copy-once only’ can only be recorded using a DVD+RW discs with CPRM (see below).
Copyright Notice
• Audio and video recordings you make using the DVD Recorder+VCR are for your personal use only. You may
not sell, lend or rent them to other people.
• This product incorporates copyright protection technology that is protected by method claims of certain
U.S.patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
corporation. Reverse engineering or disassembly is prohibited.
About DVD Recording
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지7
8
Overview
Handling the Unit
When shipping the unit
The original shipping carton and packing materials come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products
in contact with the unit for a long period of time. They will leave marks on the surface.
Cleaning the Unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild
detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage
the surface of the unit.
To obtain a clear picture
The DVD Recorder+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are
dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after
every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your
nearest dealer.
Remote Control Operation Range
Point the remote control at the remote sensor and press the buttons.
Distance: About 23 ft (7 m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
Remote Control Battery Installation
Detach the battery cover on the rear of the remote control, and insert two size
AAA batteries with and aligned correctly.
Caution
Do not mix old and new batteries. Never mix different types of batteries (standard,
alkaline, etc.).
Precautions
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지8
INTRODUCTION
9
Overview
Handling Discs
Do not touch the playback side of the disc. Hold the disc by the edges
so that fingerprints will not get on the surface. Do not stick paper or
tape on the disc.
Storing Discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct
sunlight, as there may be a considerable temperature increase inside the car.
Cleaning Discs
Fingerprints and dust on the disc can cause poor picture quality and
sound distortion. Before playing, clean the disc with a clean cloth.
Wipe the disc from the center outward.
Do not use strong solvents such as alcohol, benzine, thinner,
commercially available cleaners, or anti-static spray intended for older
vinyl records.
Notes on Discs
About the Symbol
‘ ‘ may appear on the TV screen during operation. This icon means the function explained in this owner’s
manual is not available on that specific disc.
About Symbols
NoYes
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지9
10
Identification of Controls
Identification of Controls
!
POWER
Switches the DVD Recorder+VCR ON and OFF.
@
Cassette Compartment (VCR deck)
Insert a video cassette here.
#
EJECT (VCR)
Ejects the tape in the VCR deck.
$
Disc Tray (DVD deck)
Insert a disc here.
%
EJECT (DVD)
Opens or closes the disc tray.
^
ONE TOUCH COPY
Copies from DVD to VCR (or from VCR to DVD).
&
PLAY/PAUSE
Starts playback of a disc or tape. Pauses playback
or recording temporarily.
*
STOP
Stops playback.
(
REW
DVD: Fast reverse search.
VCR: Rewinds the tape during Stop mode. Press
during Play mode for fast reverse picture search.
)
FF
DVD: Fast forward search.
VCR: Advances the tape during Stop mode. Press
during Play mode for fast forward picture search.
1
SELECT DVD/VCR
Toggles control between the DVD deck and the
VCR deck.
2
Front Panel Display
Shows the current status of the DVD
Recorder+VCR.
3
CH …/†
Scans up or down through memorized channels or
move up and down when in DVD navigation
menu.
4
REC
Starts recording. Press repeatedly to set the
recording time. Lights red when the DVD
Recorder+VCR is under recording.
5
LINE1 (VIDEO, L-AUDIO-R)
Connects to the audio/video output of an external
source (VCR, Camcorder, etc.).
POWER
PLAY/PAUSE STOP REW FF DVD• VCR
REC
CH
VCR
EJECT
VCR VCRDVD DVD
ONE-TOUCH COPY
DUAL
DVD RECORDER +VCR
DVD
EJECT
L – AUDIO – R
LINE IN 1
VIDEO
! @ # $ %
^ 3
&*() 1 2 4 5
Front Panel
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지10
INTRODUCTION
11
Identification of Controls
Front Panel Display
! Indicates a VHS tape is inserted in the VCR deck.
@ Circle : Indicates VCR is under recording process.
Clock : Indicates VCR Timer recording is set.
# Indicates that a stereo broadcast is being
received.
$ Indicates when a Second Audio Program (SAP)
broadcast is being received.
% Indicates when the DVD Recorder+VCR is playing
or recording a tape in Hi-Fi.
^ Indicates the DVD Recorder+VCR is in TV mode
(as set by the TV/VCR button).
& Indicates current Repeat mode.
* Indicates when the DVD Recorder+VCR is locked.
( Indicates when the DVD Recorder+VCR sends
video in Progressive Scan mode.
)
Disc Type indicators
Indicates the type of disc loaded.
1 Circle : Indicates DVD+R(+RW) is under recording
process.
Clock : Indicates DVD Timer recording is set.
2 Indicates a disc is inserted in the DVD deck.
3 Indicates the current Recording mode.
4 Indicates AM or PM.
5
Front Panel Display Message
Indicates clock, total playing time, elapsed time,
remaining time, title number, chapter/track
number, channel, VCR counter etc.
6 3D : Indicates the audio is virtual surround.
dts : Indicates audio material of DVD disc is dts.
Dolby : Indicates audio material of DVD disc is
Dolby Digital.
! @ # $ % ^ & * ( ) 1 2
3 4 5 6
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지11
12
Identification of Controls
Remote Control
POWEREJECT
TV VIEWDVD
TRACKING
INPUT
MENU
SETUP
EDIT
DISPLAY
ENTER
SLOW–
REW
REC
AUDIO SUBTITLE ANGLE ZOOM
REPEAT A-B SEARCH P.SCAN
TITLE CLEAR TIMER
STOP REC SPEED
PLAY/PAUSE FF
SLOW+ PREV NEXT
CH+
CH–
VCR
TV/VCR 100+
POWER
Turns DVD Recorder+VCR on and off.
EJECT
- Opens and closes disc tray in DVD mode.
- Ejects tape in VCR deck in VCR mode.
TV VIEW
Changes to channel view.
DVD
Selects DVD mode.
VCR
Selects VCR mode.
INPUT
Switches the DVD Recorder+VCR input to Tuner, LINE1, LINE2
TV/VCR
Switches between the DVD Recorder+VCR tuner and your TV tuner.
SETUP
ENTER
Displays or exits Setup menu.
DISPLAY
Displays or exits some information about the loaded disc, VHS or viewing
channel.
EDIT
Edits the chapters or splits the titles of DVD+R(+RW).
Confirms menu selections.
CH+
CH–
- œ √…† : Selects menu options.
- CH(+/–) : Selects channels.
MENU
Accesses menus on DVD discs.
TRACKING
100+
- Selects numbered options in menus.
- Selects TV channels.
- Manually adjusts tracking.
REC
Starts recording. Press repeatedly to set the recording time. For more
details, Refer to One Touch Record(OTR) in page 46.
PLAY/PAUSE
- Starts playback.
- Pauses playback or recording temporarily. Press again to exit Pause mode.
STOP
Stops playback or recording.
FF
- DVD: Searches backward/forward.
- VCR: Rewinds/advances during Stop mode. Press during Play mode for
fast reverse/forward picture search.
REW
SLOW–
SLOW+
Increases or decreases the slow motion speed when playing DVD or VHS
tape.
PREV
NEXT
Skips to next chapter/track. Skips to next or previous chapter/track.
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지12
INTRODUCTION
13
Displays disc’s Title menu, if available.
Identification of Controls
REC SPEED
Selects Recording mode: - DVD : HQ (1hr), SP (2hrs), EP (4hrs) or SLP (6hrs).
- VCR : SP or SLP.
CLEAR
Reset the counter in the VCR mode.
TIMER
Displays Timer Recording menu.
AUDIO
Selects an audio language(DVD), audio channel(CD) or audio type
(Broadcast).
SUBTITLE
Selects a subtitle language.
ANGLE
Selects a DVD camera angle, if available.
ZOOM
Enlarges DVD video image.
REPEAT
Repeats chapter, track, title or all.
A-B
Repeats sequence between two points (A and B).
P.SCAN
Switches between Progressive Scan mode and Interlace Scan mode. This
function is activated only when the key is pressed for 3 seconds.
SEARCH
Changes a title or a chapter.
POWEREJECT
TV VIEWDVD
TRACKING
INPUT
MENU
SETUP
EDIT
DISPLAY
ENTER
SLOW–
REW
REC
AUDIO SUBTITLE ANGLE ZOOM
REPEAT A-B SEARCH P.SCAN
TITLE CLEAR TIMER
STOP REC SPEED
PLAY/PAUSE FF
SLOW+ PREV NEXT
CH+
CH–
VCR
TV/VCR 100+
Progressive Scan
If your TV system supports Progressive Scan, you can view high quality video by changing
the DVD Recorder+VCR set to send video as Progressive Scan mode. If the TV system
does not support Progressive Scan mode, Never try to change to Progressive scan mode.
If you changed the TV Scan mode by mistake, press [P.SCAN] key for 3 seconds then it
will be restored.
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지13
TITLE
!
AC Power Cord
Plug into a power outlet.
@
AUDIO OUT (L, R)
Connect to a TV or other equipment with audio
inputs.
#
COMPONENT/PROGRESSIVE VIDEO OUT (Y Pb Pr)
Connect to a TV with Component (Y Pb Pr) inputs.
$
AV OUT (VIDEO, L-AUDIO-R)
Connect to a TV with video and audio inputs.
%
LINE2 (VIDEO, L-AUDIO-R)
Connect to the audio/video output of an external
source (VCR, Camcorder, etc.).
^
RF IN (FROM ANT.)
Connect to your antenna or cable TV outlet.
&
RF OUT (TO TV)
Connect to a TV with an RF coaxial input.
*
COAXIAL (Digital Audio Out)
Connect to an amplifier with a coaxial digital
audio input.
(
S-VIDEO OUT
Connect to a TV with an S-Video Input.
Rear panel
14
Identification of Controls
! @# $% ^
( * &
Caution
Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the
DVD Recorder+VCR.
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지14
S-VIDEO
OUT
DVD & VCR OUT
AUDIO OUT COMPONENT OUT
R
L
COAXIAL
DIGITAL
AUDIO OUT
LINE 2
Pr
Pb
Y
OUT
R
L
ANT. IN
AUDIO
VIDEO
RF OUT
INTRODUCTION
15
Connections
Connections
Connecting Antenna/Cable
CONNECTIONS
1
Disconnect the antenna/cable from the rear of your
TV.
2
Identify the type of cable from your antenna. If it is
a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
the jack marked RF IN (FROM ANT.) on the DVD
Recorder+VCR.
Cable Service Without Cable Box
If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your
TV and attach it to the RF IN (FROM ANT.) jack on the DVD Recorder+VCR.
Use the supplied coaxial cable to connect between the DVD Recorder+VCR’s OUT (TO TV) jack and the 75 ohm
antenna input jack on your TV. With this connection, you can receive all midband, superband, and hyperband
channels (all cable channels).
Cable Service With Cable Box
If a cable box is required in your cable system, follow
the instructions shown below. This hookup permits both
TV and DVD Recorder+VCR operation.
To view or record a CATV channel:
1
Tune the TV to the correct video input channel.
2
Set the DVD Recorder+VCR to the output channel of
the cable box using the [CH …/†] or the [0-9] keys
on your DVD Recorder+VCR (e.g., CH3).
3
Select the channel you wish to view on the cable
box.
• There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of
the connections described below. Whichever TV connection you use will work with all input sources.
• Please refer to the manuals for your TV, VCR, stereo system or other devices as necessary to make the best
connections.
• For better sound reproduction, connect the DVD Recorder+VCR’s AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment. See ‘Connecting an Amplifier/Receiver‘ on page 18.
If you are using a cable box to tune channels, it is not necessary to run Auto Channel Search as indicated on page 23.
Caution
• Make sure the DVD Recorder+VCR is connected directly to the TV, and the TV is set to the correct video input.
• Do not connect the DVD Recorder+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
• Do not connect the DVD Recorder+VCR via your VCR. The DVD image could be distorted by the copy protection
system.
T
OUT
DIGITAL
AUDIO OUT
AUDIO OUT COMPONENT OUT
LINE 2
AUDIO
VIDEO
L
R
L
R
COAXIAL
Y
Pb
Pr
RF OUT
ANT. IN
DVD & VCR OUT
Antenna Antenna
Flat Wire
(300 ohm)
300/75 ohm
Adaptor
(Not supplied)
Cable TV
Wall Jack
OR OR
Rear of DVD Recorder+VCR
EO
OUT
DIGITAL
AUDIO OUT
AUDIO OUT COMPONENT OUT
LINE 2
AUDIO
VIDEO
L
R
L
R
COAXIAL
Y
Pb
Pr
RF OUT
ANT. IN
DVD & VCR OUT
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
Rear of DVD Recorder+VCR
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지15
Choose one of the following TV connections, depending on the capabilities of your equipment.
RF Coaxial Connection
Connect the RF OUT (TO TV) jack on the DVD
Recorder+VCR to the antenna in jack on your TV using
the supplied 75-ohm coaxial cable (R). If you use this
connection, tune your TV to the DVD Recorder+VCR’s
RF output channel (CH 3 or 4).
How to set the DVD Recorder+VCR’s RF output channel
Press [SETUP] and select Modulator out then press
[ENTER] to change the RF out channel. For details
refer to page 24.
Audio/Video Connection
1
Connect the VIDEO OUT jack on the DVD
Recorder+VCR to the video in jack on your TV
using the supplied video cable (V).
2
Connect the Left and Right AUDIO OUT jacks
from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables (A).
S-Video Connection
1
Connect the S-VIDEO OUT jack on the DVD Recorder+VCR to the S-Video in jack on your TV using an SVideo cable (S).
2
Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on
your TV using the supplied audio cables (A).
Component Video Connection
1
Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding
in jacks on your TV using a Y Pb Pr cable (C) if the component (Y, Pb, Pr) is available on your TV.
2
Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on
your TV using the supplied audio cables (A).
Connecting a TV
16
Connections
All video signals are available from all video outputs.
That means that whichever TV connection you use, it will
work with all input sources, including VHS out of the Component/Progressive Video Output.
ANTENNA
INPUT
L
R
Y
Pb
Pr
COMPONENT/PROGRESSIVE VIDEO INPUT
AUDIO INPUT
VIDEO
INPUT
S-VIDEO
INPUT
Rear of TV
S-VIDEO
OUT
OUT
DIGITAL
AUDIO OUT
AUDIO OUT COMPONENT OUT
LINE 2
AUDIO
VIDEO
L
R
L
R
COAXIAL
Y
Pb
Pr
RF OUT
ANT. IN
DVD & VCR OUT
Rear of DVD Recorder+VCR
R
S AVC
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지16
CONNECTIONS
17
Progressive Scan Connection
• If your television is a high-definition or ‘digital ready‘ television, you may take advantage of the DVD
Recorder+VCR’s Progressive Scan output for the highest video resolution possible.
• If your TV does not accept the Progressive Scan format, the picture will appear scrambled.
1
Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding
in jacks on your TV using an optional Y Pb Pr cable (C).
2
Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on
your TV using the supplied audio cables (A).
• Be sure to set the DVD Recorder+VCR to the Progressive Scan mode by pressing [P.SCAN] for 3 seconds on the
remoter control or changing the Scan mode in the Setup Menu; See page 27.
• Progressive Scan does not work with the RF, Audio/Video or S-Video connections.
Connections
DWL71D1D_RV4000(GB) 04.6.1 1:45 AM 페이지17
18
Connections
Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/ Pro Logic
Connect the Left and Right AUDIO OUT jacks on the DVD Recorder+VCR to the left and right audio in jacks on
your amplifier, receiver, or stereo system, using the supplied audio cables (A).
Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/Video receiver equipped
with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)
1
Connect one of the DVD Recorder+VCR’s DIGITAL AUDIO OUT jacks (OPTICAL O or COAXIAL X) to the
corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.
2
You will need to activate the DVD Recorder+VCR’s digital output; see ‘AUDIO Settings‘ on page 28.
Digital Multi-Channel Sound?
A digital multi-channel connection provides the best sound quality. For this you need a multi-channel
audio/video receiver that supports one or more of the audio formats supported by your DVD Recorder+VCR
(MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.
Connecting an Amplifier/Receiver
Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.
• If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce
a strong, distorted sound or no sound at all.
• 5.1 channel digital surround sound via the digital connection can only be obtained if your receiver is equipped with
a digital multi-channel decoder.
• To see the audio format of the current DVD on the on-screen display, press [AUDIO].
The DVD Recorder+VCR does not perform internal (2- channel) decoding of DTS sound tracks. To enjoy DTS multichannel surround, you must connect the DVD Recorder+VCR to a DTS compatible receiver via one of the DVD
Recorder+VCR’s digital audio outputs.
Amplifier (Receiver)
R
L
AUDIO INPUT DIGITAL INPUT
COAXIAL
S-VIDEO
OUT
OUT
DIGITAL
AUDIO OUT
AUDIO OUT COMPONENT OUT
LINE 2
AUDIO
VIDEO
L
R
L
R
COAXIAL
Y
Pb
Pr
RF OUT
ANT. IN
DVD & VCR OUT
Rear of DVD Recorder+VCR
A X
DWL71D1D_RV4000(GB) 04.6.1 1:46 AM 페이지18
CONNECTIONS
19
Connections
REC
CH
DVD RECORDER +VCR
DVD
EJECT
L – AUDIO – R
LINE IN 1
VIDEO
To receive audio/video signal from other equipment,
connect the LINE1 or LINE2 jacks on the DVD
Recorder+VCR to the audio/video out jacks on your
external component, using optional audio/video cables.
Connecting Optional Equipment
If you use the S-VIDEO jack on the front panel, there is
no signal output from the front panel VIDEO jack.
OUT
LINE 2
AUDIO
VIDEO
L
R
RF OUT
ANT. IN
DWL71D1D_RV4000(GB) 04.6.1 1:46 AM 페이지19
Loading...