Win-Holt WHSS-1 User Manual
Film Wrapper Technical Bulletin
Models:
WHSS-1; WHSS-2;
WHSC-3; WHSC-3/KD
New York • Pennsylvania • Georgia • Texas • California
China • India
800-444-3595 www.winholt.com
1
Directory
Customer Service Bulletin............................2
Film Loading Instructions:
Film Axle.........................................................3
Film Roll Axle Assembly lnstuctions...........4
Electrical Diagram.........................................5
Testing............................................................6
Replacement Parts........................................7-10
Trouble Shooting...........................................11
Assembly Instructions For WHSC-3/KD.......12-13
WHSC-3
Customer Service Bulletin
CUSTOMER SERVICE BULLETIN
The Win-Holt Film Wrappers are used to apply a thin plastic lm or
protective plastic covering over packaging. They consist of a lm
dispensing mechanism, a heated cut off rod, and a heated plate for
sealing the lm.
DISPENSING MECHANISMS: AXLE
The Dispensing Mechanisms of lm is axle. The wrappers are
available as table models for one or two rolls of lm or a console
model for three rolls mounted on axles. Models accept lm roll
widths up to 18”. Contact your lm supplier for application information
regarding lm thickness and color.
HEATED CUT OFF ROD
The Heated Cut-off Rod cuts the desired length of lm. The
temperature is factory preset and controlled electronically.
HOT PLATE SEALING
The Hot plate is an aluminum casting with a bolt-on element. The
operator seals the ends ofthe lm on the Hot Plate. The thermostat which is mounted under the hot plate is adjusted by a plastic
knob mounted on the right side of the hot plate. Adjustment ranges
from”off to a maximum of 410°F. Temperature setting is determined
by lm thickness, air temperature (kitchen or cooler) and operator’s
speed.
REPLACEMENT PARTS: IN-STOCK AND INTERCHANGEABLE
Replacement parts are available in stock for immediate shipment.
ELECTRICAL LOAD
Unit is rated at 8 AMPS, 115 VOLTS
New York • Pennsylvania • Georgia • Texas • California
China • India
800-444-3595 www.winholt.com
2
Loading The Film Axle
LOADING THE FILM AXLE:
1. Loosen all Wing Nuts. Swing out right and left Bearing Blocks.
2. Lift out the Axle Assembly. Unscrew Wing End Cap, position Pin
End Cap for correct fi lm width, secure with Pin and 0-Ring.
3. Position the cardboard core of the Film Roll against the taper
of the Pin End Cap. Make certain thatthe fi lm will dispense
from the bottom ofthe roll.
4. Replace Wing End Cap and Screw tightly.
5. Replace Axle and Film onto the Lower Bearing Blocks. Swing
Upper Bearing Blocks back into place. Tighten and adjust Wing
Nuts for desired fi lm tension.
MODEL: WHSS-1
MODEL: WHSC-3
MODEL: WHSS-2
New York • Pennsylvania • Georgia • Texas • California
China • India
800-444-3595 www.winholt.com
3
Film Roll Axle Assembly
FILM ROLL AXLE ASSEMBLY INSTRUCTIONS:
1. Install Bearing Block Assembly (A) on the left side of Base, line
up holes and insert Carriage Bolts (B) and tighten using Wing
Nuts (C).
2. Repeat step (1) on right side of Base.
3. Loosen all Wing Nuts (D) on Bearing Blocks on both sides to
loosen top of Bearing Blocks, and then rotate top to expose
Film Roll Axle Slots.
4. Install Film on Film Roll Axle (F), tighten Core Adapter Wing
Nut (G), and insert in slots in the bottom of the Bearing Blocks.
5. Rotate the top of Bearing Block to cover shaft of Film Roll Axle,
and tighten Wing Nuts (D) to the required tension.
MODEL: WHSS-1
New York • Pennsylvania • Georgia • Texas • California
China • India
800-444-3595 www.winholt.com
4
Loading...