WINGITS WPGB5PSxxTAP User Manual
Technical Data Sheet
Model:
WPGB5TAP
Part Numbers:
WPGB5PS12TAP WPGB5SN12TAP
12” Polished Finish
WPGB5PS16TAP
16” Polished Finish
WPGB5PS18TAP
18” Polished Finish
WPGB5PS24TAP
24” Polished Finish
WPGB5PS30TAP
30” Polished Finish
WPGB5PS32TAP
32” Polished Finish
WPGB5PS36TAP
36” Polished Finish
WPGB5PS42TAP
42” Polished Finish
WPGB5PS48TAP
48” Polished Finish
12” Satin Finish
WPGB5SN16TAP
16” Satin Finish
WPGB5SN18TAP
18” Satin Finish
WPGB5SN24TAP
24” Satin Finish
WPGB5SN30TAP
30” Satin Finish
WPGB5SN32TAP
32” Satin Finish
WPGB5SN36TAP
36” Satin Finish
WPGB5SN42TAP
42” Satin Finish
WPGB5SN48TAP
48” Satin Finish
PLATINUM
™
Stainless Steel Grab Bar - Taper Flange
• 7 Bold Flange Designs
• All parts are 18/8 Stainless Steel (Type 304) - tubing is 18-gauge (1.2mm)
• Mounting Flanges are 3”(75mm) in diameter, 3/32”(2.5mm) thick, HeliArc
welded to the tubing. Mounting Flanges have 5 holes for attachment to WINGITS
or adequate blocking.
• High End Cast Stainless Steel threaded Flange covers thread onto the Cast
Stainless Steel Flanges
• Provide 1-1/2”(38mm) clearance from wall.
Platinum Flange Style Options
BAND = BAN
HALO = HAL
ROPE = ROP
BEVEL = BEV
HEX = HEX
TAPER = TAP
TRI-STEP = TRI
MECHANICAL DATA
Width: See product part number for width. Complete length of Grab Bar is usable surface.
Diameter: 1.25” (3.2cm)
PRODUCT COMPOSITION
Entire product is 18/8 (304) stainless steel.
MODALITY
Use: Wall Installation.
Load Capability: 800 lbs (362.9kg)
INSTALLATION
®
W
INGITS
PLATINUM™ Structural Stainless Steel Grab Bars are designed to hold live loads and
must be installed into adequate structural blocking or with WI NGITS® Grab Bar Fasteners
CERTIFICATIONS
®
W
INGITS
PLATINUM™ Structural Stainless Steel Grab Bars meet or exceed the
applicable requirements of all building codes, ADA criteria, and 2010 ADAAG and
2009 ANSI standards.
RECOMMENDED INTEGRATION
®
INGITS
For hollow wall construction, it is recommended that W
are used with this product. See Fastener instructions for applications.
Grab Bar Fasteners
20140822_rev3
Toll Free: 877-894-6448 • www.wingits.com • sales@wingits.com
1.25’’
Technical Data Sheet
Overall Length
(Mounting Length +3’’)
Mounting Center Length
(12’’ to 48’’)
2.75’’
Holes - 1/4”
Slots - 1/4” x 1/2”
(used when installing with
the WINGITS® Grab Bar
Fastening System)
Bolt Circle is 2.3125”
3’’
Grab Bar
Mounting Flange
Grab Bar Tube
Overall Length
(Mounting Length +3’’)
Thread on Cover
3”
.5” Cover
Height
INCLUDED HARDWARE
Stainless Steel Screws x 6
Toll Free: 877-894-6448 • www.wingits.com • sales@wingits.com
OPTIONAL HARDWARE
(Sold Separately)
Grab Bar WingIts (GBW40) x 2 RES WingIts (RESGBW35) x 2
Loading...