WINGITS RESGBW35 User Manual
WINGITS
®
RESGBW35
World’s Strongest Fastener
RESGBW35
Structurally Engineered Grab Bar WINGITS
Features / Benefits
• Exceeds ADA Guidelines and ALL Building Codes
• Eliminates the need for Blocking
• Waterproof and Fire-resistant
• Rated up to 600 lbs. in Drywall with Tile
• Used to Install WINGITS® Grab Bars
• Patented Worldwide
™
®
Install WINGITS® RESGBW35 Quickly and Easily
with the APACHE200 Carbide Drill Bit
Industrial Grade Carbide Drill Bit
• Rated at 200 holes in ceramic wall tile
• Drills holes through ceramic wall tiles in seconds
• No hammer drill required - this precision cutting drill does all the work
• Industrial grade carbide cutting tool
• Engineered for standard and cordless drills
• Designed for ceramic, marble and plaster
Installation Videos can be viewed at:
www.wingits.com
Bradley Beach, NJ USA • Toll Free: 877-894-6448
www.wingits.com • sales@wingits.com
W34-05022013
WINGITS
®
Commercial Grab Bar Fastening System Installation Guide. WINGITS
®
Grab Bar Fastening Systems
Installation Instructions
RESGBW35
Exceed Building Codes For Grab Bars In The Following Wall Substrates:
• 5/8” Drywall - Painted or Wallpapered
• 1/2” or 5/8” Drywall with Tub Surrounds
• 1/2” or 5/8” Drywall with Tile, Marble or Stone
• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass, Faux Marble, Acrylic and Plastics
• Multiple Layers of Drywall, Plaster and Lathe
• 1/4” Acrylic/Fiberglass Tub Surrounds
• Most Wall Panels, All Masonary Type Boards, with or without Decorative Panels
NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL
When Attempting To Meet Commercial Building Codes.
NOTE: For Maximum Safety and to meet ADA Requirements, Grab Bars should be Installed Horizontally 33-36” from the floor.
Before You Install:
• Verify the length of the grab bar by measuring from the inside of one flange to the outside of the other.
• To ensure adequate clearance, a stud finder should be used to verify there are no studs within the area
where the WINGITS® will be installed.
Make sure that there is at least 1.5” away from the edge of the stud. If concerned, drill a pilot hole and insert a piece of wire in
the shape of an “L” - twirl the wire to make sure there is nothing in the way.
• Clean wall surface
Screw
Wings
INSTALLATION INSTRUCTIONS
1. PEEL the 1/4” liner (scored)
off the tape and fold up until
properly placed.
3. Use the tape as a template,
Drill out two 3/4” holes.
5. Insert the WINGS into the FACEPLATE
(the tubes interlock). Extend the WINGITS
FACEPLATE
WINGS
6. Compress and insert the WINGS
into the drilled hole.
7. WINGS should be flush with the
wall surface.
8. Pop WINGITS
by pushing on the FACE PLATE.
®
through the hole
Installation Holes
2. Determine location of Grab Bar and mark
length on the wall, remove center hole,
then place tape with the center hole over
mark. Stick tape to the wall remove the remaining liner.
4. Once holes are drilled remove tape liner.
®
to full length.
Face Plate
9. Using the enclosed 3.5”
STAINLESS STEEL SCREWS,
attach the object to the WINGITS
Grab Bar installed with RESGBW35 WINGITS
NOTE:
Strength and stability are greatly affected by
projection off the wall surface and the length
of interaction with the wall surface. Call us at
877.894.6448 for guidance. WINGITS
designed to be used in vertical walls only.
DO NOT USE IN CEILINGS.
Screw
3M®
Waterproof
Tape/Liner
®.
®
Wings
®
are
View Installation Videos at: www.wingits.com
Loading...