Automatic Multi-Satellite TV Antenna
Replacement LNB Instructions
for Models RP-SK01, RP-SK05, RP-SK09, and RP-SK73
For help, email help@winegard.com or call 1-800-788-4417
www.winegard.com/mobile
2452261
Raising the Antenna
1. Press and hold “POWER” for two seconds to turn on the interface
box. Wait until the interface box finishes “connecting to antenna.” The
TRAV’LER® antenna may enter the search routine after ten seconds.
Pay attention to the pinch points as the antenna raises!
2. Wait until the antenna has at least raised to a position in which the feed
arm is parallel to the roof. Then, press “POWER” and “SELECT” at the
same time. The antenna should stop moving.
3. Unplug the interface box. Continue with instructions for your model of
replacement LNB.
Model RP-SK01 DISH® 1000 Replacement LNB
1. Remove and set aside the two screws from the wider end of the
underside of the integrated adapter.
2. Carefully slide the LNB out from
the integrated adapter. Disconnect
LNB slid out from
integrated adapter
the three cables from the LNB
using a 7/16” wrench.
3. Connect the three cables running
through the integrated adapter
to ports 1–3 (in any order) on the
replacement LNB. Tighten each
cable until fingertight, and then use
a 7/16” wrench to tighten a quarter
Integrated
adapter
Screws removed
from integrated adapter
turn more.
4. Slide the LNB into the integrated adapter, and re-install the two
screws (removed earlier) through the integrated adapter and LNB.
Model RP-SK05 DIRECTV® Slimline Repl. LNB
1. Remove and set aside the four
nuts and bolts holding the LNB
guard to the feed arm. Then, slide
the LNB guard down the feed arm
and toward the reflector.
2. Remove and set aside the two screws
holding the LNB to the feed arm.
Bolts holding
LNB guard
to feed arm
LNB guard
Screws holding
LNB to feed arm
3. Carefully slide the LNB out from the feed arm. Disconnect the four
coax cables from the LNB using a
7
/16” wrench.
4. Connect the four coax cables running through the feed arm to the
replacement LNB. The coax cables can be connected in any order.
Tighten the cables until fingertight, and then use a 7/16” wrench to
tighten a quarter turn more.
5. Slide the LNB into the feed arm, and re-install the two screws
(removed earlier) through the underside of the feed arm and
replacement LNB. Tighten.
6. Slide the LNB guard up the feed arm and over the LNB. The front of
the LNB guard should be ~½″ in front of the LNB and should not be
touching the LNB. Install the four bolts through the four holes in the
LNB guard. Thread a nut onto each bolt, and tighten.
Model RP-SK09 DIRECTV SWM Slimline Repl. LNB
1. Remove and set aside the four
nuts and bolts holding the LNB
guard to the feed arm. Then, slide
the LNB guard down the feed
arm and toward the reflector.
2. Remove and set aside the two
screws holding the LNB to the
feed arm.
3. Carefully slide the LNB out from the
feed arm. Disconnect the coax cable
from the LNB using a 7/16” wrench.
4. Connect the coax cable running through the feed arm to the
replacement LNB. Tighten the cable until fingertight, and then use a
7
/16” wrench to tighten a quarter turn more.
5. Slide the LNB into the feed arm, and re-install the two screws
(removed earlier) through the underside of the feed arm and
replacement LNB. Tighten.
6. Slide the LNB guard up the feed arm and over the LNB. The front of
the LNB guard should be ~½″ in front of the LNB and should not be
touching the LNB. Install the four bolts through the four holes in the
LNB guard. Thread a nut onto each bolt, and tighten.
Front of
LNB guard
Bolts holding
LNB guard
to feed arm
Screws holding
LNB to feed arm
Feed arm
Model RP-SK73 Shaw Direct Replacement LNB
1. Remove and set aside the four nuts and bolts holding the LNB guard
to the feed arm. Then, remove the LNB guard from the feed arm.
2. Remove and set aside the screw holding the LNB to the feed arm.
3. Disconnect the four coax cables from the
LNB using a 7/16” wrench, and carefully
remove the LNB from the feed arm.
4. Connect the four cables running
through the feed arm to the four
ports on the replacement LNB. The
cables can be connected in any order.
Tighten each cable until fingertight,
and then use a 7/16” wrench to tighten
a quarter turn more.
Four coax cables
connected to LNB
5. Slide the LNB into the feed arm, and re-install the screw (removed earlier)
through the underside of the feed arm and replacement LNB. Tighten.
6. Slide the LNB guard onto the feed arm and over the LNB. The front of
the LNB guard should be ~½″ in front of the LNB.
Screw holding
LNB to feed arm
Bolts holding LNB
guard to feed arm
7. Install the four bolts through the four holes in the LNB guard. Thread a
nut onto each bolt, and tighten.
Stowing the Antenna
1. Plug in the interface box.
2. Press and hold “POWER” for two seconds to turn on the interface box.
Then, press the Power button again to stow the antenna.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
1-800/788-4417 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. • ©2012 Winegard Company Rev1 4/13 2452261
DIRECTV is a registered trademark of DIRECTV, LLC. DISH is a registered trademark of DISH Network L.L.C.
Disclaimer: Although every effort has been made to ensure that the information in this manual is correct
and complete, no company shall be held liable for any errors or omissions in this manual. Information
provided in this manual was accurate at time of printing.
Winegard and TRAV’LER are registered trademarks of Winegard Company.
Shaw Direct is a trademark of Shaw Satellite G.P.
Loading...