Winegard RA-7296 User Manual
set 2 cable as shown in Figure 5. Attach
downlead cable to jack on wallplate/amplifier
marked antenna as shown in Figure 4. Attach
cable going to set 2 outlet to jack on power
supply marked SET 2. Attach cable coming
from cable input to jack on power supply marked
CABLE.
Set 2
Antenna
FIGURE 4
Cable
STEP 6. Mount wall plate/amplifier in wall
with screws provided and attach TV set cable to
jack on front. Connect TV set cable to input jack
on TV. Press switch on front of outlet and check
that light is on.
OPERATION: To receive cable signals
from outdoor receptacle: Press switch to
OFF position. Light on wallplate will go (OFF)
showing that power is no longer connected to
the amplifier and that both TV sets are receiving
signals from outdoor receptacle.
To receive signals from antenna: Press
switch to ON position. Light on wallplate will
come (ON) showing that power is connected to
the amplifier and both TV sets are receiving
signals from the antenna.
NOTE: Make sure the antenna is in the operating
position (up) and pointed at the station desired.
INSTALLING FC-5910
CONNECTORS ON COAX CABLE
1.
Outer Cover
2.
3.
Crimp Here
Step 1: Strip outer cover back 1/2"* from end of cable. Fray
braid back as far as outer cover will allow.
Step 2: Trim braid close to outer cover and remove 1/4"* of
inner insulation being careful not to nick center conductor.
Make sure no foil or braid can touch center conductor.
Step 3: Slide connector tip between braid and inner insulation
(braid and foil, on foil shield cable) and push connector on cable
as far as it will go. Crimp built-in ferrule with proper crimping
tool. Hex connector requires hex crimping tool. Do Not
crush cable out-of-round.
* If installing in very hot weather, increase dimensions 1/8"
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
Winegard Company warrants this product against defects in materials or
workmanship for a period of two (2) years from the date of original purchase. During
year one (1) of such warranty, Winegard Company will also pay authorized labor
costs to an authorized Winegard dealer to repair or replace defective products. No
warranty claim will be honored unless at the time the claim is made, Customer
presents proof of purchase to an authorized Winegard dealer (to locate the nearest
authorized Winegard dealer, contact Winegard Company, 3000 Kirkwood Street,
Burlington, Iowa 52601, Telephone 800-288-8094 or visit www.winegard.com).
Customer must provide proof of purchase with a dated sales receipt for the Winegard
product to verify the product is under warranty. If the date of purchase cannot be
verified, the warranty period shall be considered to begin thirty (30) days after the
date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the
product to an authorized Winegard dealer for service. Customer must provide
proof of purchase to verify the product is under warranty. If the product is brought to
an authorized Winegard dealer for service prior to expiration of year one (1) of the
warranty period and a defect in material or workmanship is verified by Winegard
Technical Services, Winegard Company will cover the Winegard dealer’s labor
(2 YEARS PARTS; 1 YEAR LABOR)
1/2" *
Inner Insu lation
¼" *
Center Conduc tor
FIGURE 5
charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval of the service is
at the sole discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3111 Kirkwood Street, Burlington, Iowa 52601, Telephone 800788-4417). Customer must return the product along with a brief description of the
problem and provide Winegard Technical Services with Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify
the product is under warranty. If the product is returned before the expiration of the
warranty period, Winegard Company will (at its option) either repair or replace the
product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation, misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard
in any manner whatsoever, removing or defacing any serial number, usage not in
accordance with product instructions or acts of nature such as damage caused by
wind, lightning, ice or corrosive environments such as salt spray and acid rain. This
Limited Warranty also does not apply if the product becomes unable to perform its’
intended function in any way as a result of the television signal provider making any
changes in technology or service.
A Return Material Authorization (RMA) is required prior to returning any product to
Winegard Company or Winegard Warranty Services under this warranty policy.
Please call our Technical Services Department at 800-788-4417 or send an e-mail
to warranty@winegard.com to obtain the RMA number. Please furnish the date of
purchase when requesting an RMA number. Enclose the product in a prepaid
package and write the RMA number in large, clear letters on the outside of the
package. To avoid confusion or misunderstanding, a shipment(s) without an RMA
number(s) or an unauthorized return(s) will be refused and returned to Customer
freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE
AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS
WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of
limitation of incidental or consequential damages, the above limitations or exclusions do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the
exclusion of limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state.
RETURN AUTHORIZATION POLICY
SATELLITE RECEIVER WARRANTY
See manufacturer’s limited warranty policy.
WS-MOBWARREV2 Rev. 1/10
Printed in U.S.A. 2451489 Rev. 1/10
INSTRUCTIONSSTEP 5. Install connectors on downlead and
MODEL RA-7296
Made in U.S.A.
RV WALL PLATE/
AMPLIFIER
DESCRIPTION
Wall plate/amplifier amplifies VHF/UHF TV
signals received by non-amplified Winegard
RV antennas with outdoor receptacle for TV set
and cable input. Wall plate/amplifier provides
a +12 Volt receptacle as well as antenna signals
to two TV sets. Cable input from outdoor
receptacle connects to wall plate and may be
switched so either antenna or cable signals
may be watched. See applications. Available
in white only.
NOTE: THIS UNIT IS AN AMPLIFIER. USE ONLY
WITH NON-AMPLIFIED RV ANTENNAS.
WINEGARD COMPANY
3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000
WARNING: Use this amplifier/
switch with only non-amplified
RV antennas.
APPLICATIONS AND
ALTERNATE CONNECTIONS
Non-Amplified
Antenna
Cable Input
Antenna
Input
Cable Input
Example 1
ON/OFF
Switch
Outdoor Receptacle
WA-1010
Set 1
WARNING: Do not connect high
current devices such as hair
dryers to +12 volt receptacle on
wall plate/amplifier. Maximum
current ratings of this receptacle
is 7.5 amps at +12 VDC.
TV
Outlet
Set 2
Non-Amplified
Antenna
Antenna
Input
ON/OFF
Switch
Antenna
Input
ON/OFF
Switch
Set 1
Non-Amplified
Antenna
Set 1
Cable
Input
Set 2
Example 2
Cable
Input
Set 2
Example 3
Outdoor Receptacle
WA-1010
TG-7221
Outdoor Receptacle
WA-1010
TV
Outlet
TV-1030
Splitter
TG-7221
INSTRUCTIONS
STEP 1. Select location for wall plate and
outdoor receptacle. Run two coax cables (RG59 type) between locations and install
connectors on each end. Mark cables so
"cable input" and "TV output" may be
identified. Antenna downlead and +12 VDC
will also be needed at inside wall plate/amplifier
location.
STEP 2. Refer to outdoor receptacle
instruction sheet on how to install cables and
receptacle. Make sure jack on outdoor
receptacle marked CABLE INPUT is attached
to cable going to jack marked CABLE on indoor
wall plate/amplifier.
STEP 3. The wall plate/amplifier assembly
may be flush mounted in most standard
electrical boxes. To flush mount cut a hole in
wall to fit the box. Run 2 #12 wires between wall
plate/amplifier and +12 VDC source and route
downlead cable to this location. Install cable
between set 2 outlet and power supply location
at this time.
WHEN CONNECTING CABLE OR WIRES
BE SURE SWITCH IS IN OFF POSITION.
STEP 4. Install terminals on wires from +12
VDC source as shown in Figure 1. Crimp
terminals with Craftsman type 4 crimping tool
or equivalent. See Figure 1. Push wires onto
tabs on terminal board as shown in Figure 2. If
in doubt as to the polarity of the wires, connect
them temporarily to tabs on circuit board and
press switch on front of outlet. If light comes on
polarity is correct. See Figure 3.
Connector
Insulation
FIGURE 1
FIGURE 2
FIGURE 3
Crimp Here
1/4"
Connector
Ferrule
#12 Wire
Remove 1/4" of
insulation from
#12 wire.
+12 VDC
Ground
WARNING
DO NOT connect high
current devices such as
hair dryers to this
receptacle. Maximum
current rating of this
receptacle is 7.5 amps at
12 VDC.
Loading...