Winegard MM-3003, MM-3200, MM-3084, MM-3002 User Manual
INSTALLATION INSTRUCTIONS
®
WINEGARD
18" Digital Satellite Antenna
Truck/RV Mount
Model MM-3200 Antenna
Models MM-3084, MM-3002 & MM-3003
ANTENNA/MOUNT MADE IN U.S.A.
U.S. Patent 5,532,710
NOTE: The MM-3084 Mount Pipe and
MM-3002/3003 Clamp Brackets are not
supplied with MM-3200.
LNBF
Feed Support
Elevation
Assembly
18" Antenna
Backup Support
UNPACKING
After unpacking the system, verify that you have the
following: antenna/mount, elevation assembly, feed
support w/LNBF & coaxial cable attached, compass and
storage bag. If you do not, call Winegard Company at
1-800-288-8094 between the hours of 8:00 a.m. and
3:30 p.m central time, Monday through Friday.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787
Printed in U.S.A. © Winegard Company 1999 2451160 Rev. 10/99
NOTE: Before proceeding with installation of
satellite antenna/mount, viewing enclosed
installation video is recommended.
ASSEMBLY
STEP 1. Attach feed support to the backup support.
See Figures 1 & 2. Make sure spring is locked into
place.
Feed Support
E-Clip
After inserting pin,
swing long part of
spring up into the
feed support and
snap into place
under cable clip.
Spring
Feed Support
Pin
Spring
Coax Downlead
from LNBF
E-Clip
Backup Support
Backup Support
Pin
FIGURE 1
STEP 2. Remove the two top bolts from the backup
support and attach the elevation assembly to antenna.
See Figure 3. Tighten bolts securely.
FIGURE 2
Slide elevation
assembly into place
Elevation Assembly
FIGURE 3
2
Backup Support
STEP 3. Attach the MM-3084 (pipe that antenna
mounts on) to your truck/RV. If using the MM-3002
clamp brackets, proceed to step 9. If using the MM3003 clamp brackets, proceed to step 4.
MM-3003 Assembly
STEP 4. Disassemble pipe per number sequence
shown in Figure 4 so that you can slide both MM-3003
brackets onto the pipe.
MM-3003
4
Pin
Stop Collar
1
2
3
STEP 7. Use (4) 5/16" x 1-1/2" bolts supplied to secure
pipe clamp brackets to side of truck/RV. See Figure 5.
Try to maintain as much separation between the
clamp brackets as possible. See Figure 7. It is
recommended that you attach the top clamp with one
bolt, then check vertical alignment before attaching
bottom clamp and finishing top.
Make sure pipe
is vertical
Try to maintain as
much separation
between the
clamp brackets
as possible.
See Figure 7,
page 4.
Elevation
FIGURE 4
STEP 5. Reassemble pipe after sliding both clamp
brackets onto pipe; make sure the stop collar snaps
firmly onto the pin.
STEP 6. Determine where you want to mount the
pipe. It is recommended that you try to bolt into
something solid on your truck/RV and someplace close
to a window so you can listen/watch your TV when
tuning the system. Make sure pipe is vertical (straight
up and down), this will make finding the satellite(s)
easier. Also make sure antenna will clear top of
truck/RV (if possible). NOTE: A second set of
clamp brackets and pipe is recommended for other
side of truck. Winegard Company cannot recommend
specific mounting locations because of the many truck/
RV styles.
Clamp
Use (2) 5/16" x 1-1/2"
bolts supplied per
clamp
Tighten bolt to prevent
pipe from moving
FIGURE 5
STEP 8. Tighten clamp bracket bolts to prevent pipe
from moving, See Figure 5. You are now ready to aim
the antenna; proceed to Operation, page 5.
Rev. 5/99
3
Loading...