Windster WIND1024 Installation

RA-7730SS RA-7736SS
RA-7742SS RA-7748SS

For residential and indoor use only.

4

Limited Wa r ranty P.1 5 -P.1 6

WINDSTER recommends that all kitchen range hood

be installed by a certified installer.

27”-35”

27” 35”

If the hood is mounted too low, it may caused heat damaged and fire hazard.

IMPORTANT SAFETY INSTRUCTIONS
WARNING – To reduce the risk of fire, electric shock, or injury to persons, observe

the following:
DO NOT spray any liquid form cleaner on hood surface including lights and control
switch. To clean the range hood, spray liquid form cleaner directly onto cleaning
cloth for hood cleaning.

A. Use this unit onl y in the manner i

code(s).

- All electrial work have to be done by certified electrician.

- This range hood requires a 120V/60Hz electrical supply and must meet local required
safety code(s).

Installation and Maintenance must be carried out by qualified installer

Duct cover and extension duct cover fitment may vary depend on the mounting height of the
range hood.

5

Install the Upper Mounting Bracket and then adjust the duct to the required height.

.

Ensure the mounted range hood is level when installed for optimum performance.
(Fig.4)

NOT

To fit the duct to the top of the chimney, slide the bottom lip under the black plastic
plate and then lock into place with the 4 screws provided(Fig. 5)

The chimney duct can be adjust to
desired height.

11-3/4"

Fig. 5

Fi g . 6 Fi g . 7

Use a level to balance out both sides to
ensure the hood will be properly mounted.

Prepare and extend the duct cover to your
desired height for mounting.

Mount the unit onto the wall with correct
wall screws. (Note different types of walls
require different types of screws)

Fi g . 9Fi g . 8

Measure and balance the duct cover
bracket at the desired height.

Fi g . 10

Install the aluminum flex hose to the outlet
of the hood. (Flex hose not included)

Fi g . 11

Duct cover will come with “teeth” to be
installed into the slot on the hood.

6

Black plastic plate.

Fi g . 12

Correctly align the duct cover into black

Fi g . 13

plastic plate.

Fi g . 14

Evenly slide duct cover into the slot of the
hood.

Fi g . 16 Fi g . 17

Screw in the screws into the bottom duct
cover to the hood.

Fi g . 15

Attach duct cover to duct cover bracket
and screw in the screws provided.

Completed photo of how the finished
installation should look like.

7

All figures below are for optional ductless installation. The
steps will continue after Figure 9 above.

Fig. 18

Figure 18 (Ductless kit box photo)
–Remove the content from box.

Kit will include:
Fig. 19 - (1) Recirculation exhaust
Fig. 20 - (1) Round collar
Fig. 21 - (2) Charcoal filter
Fig. 22 - (6) Screws

Fig. 23 Measure and balance the
recirculation exhaust and line it up
with the exhaust opening in the duct
cover.

Fig. 24 Install aluminum flex hose in
between the recirculation exhaust and
the outlet of the hood.(Flex hose not
included)

Fig. 25 Remove grease filters (baffle
or aluminum) to expose the motor.

Fig. 19

Fig. 21

Fi g . 23

Fig. 20

Fig. 22

Fi g . 24

Fig. 26 Install covering the white
plastic grill and rotate
counter-clockwise. Installation
complete when it is secured.

Fi g . 25

8

8

Fi g . 26

Test the LED lights after putting the LED lights back into original position.

AL700

9

10

3W

AL700

27

Problem

Check power plug to see if it is plugged
firmly into the power socket.

10

28

Range hood should be turn on before cooking to create air pocket.
After cooking, range hood should be kept on for additional time until complete
ventilation of cooking odor.

9

10

28

11

1111

Model:
RA-77 Series

Switch

Switch holder

12

29

Motor

Yellow

Capacitor

LED LED

Blue

Gray

Red

White

Brown

White

Power

R

Fig. 29 RA-77 Series Electrical Schematic Diagram

White

Black

RA-77 SERIES

See M. DIAGRAMS (Page.14)

3W

LED Driver

Green

160W

13

14

Limited Warranty

Windster Hoods Inc. warrants this product against defects in material or

workmanship as follows:

1) Labor: For a period of one (1) year from the date of purchase, if this product

is determined to be defective, Windster will repair or replace the product, at its

option, at no charge. After the warranty period, you must pay for all labor

charges. During the “labor” warranty period there will be no c

2) Parts: In addition, Windster will supply, at no charge, new or rebuilt

replacements in exchange for defective parts for a period of two (2) years.

After the warranty period, you must pay for all parts costs. During the “parts”

warranty period, there will be no charge for parts

You must carry-in or mail-in your product during the warranty period. This warranty

only applies to products purch

ased and serviced in the United States or Canada.

What Is Not Covered By These Warranties:

1) Conditions and damages resulting from any of the following:

Improper installation, delivery, or maintenance.

Any repair, modification, alteration or adjustment not authorized by the

manufacturer or an authorized service dealers.

Misuse, abuse, accidents, or unreasonable use.

Incorrect electric current, voltage or supply.

Improper setting of any control.

Improper chemical cleaning.

2) Light Bulbs

3) Products purchased for commercial or industrial use (such as in a hotel, office,

restaurant, or other business)

4) Damage due to earthquake, flood, storm, etc.

harge for labor.

15

Defective Products:

.

All products will be inspected, tested, and carefully packed by the manufacturer

before shipping to customers. Products that are damaged during transit can only be

exchanged for the same product, under the condition that the customer must get a

RMA (Return Merchandise Authorization) from Windster. When products are

received defective, you must notify us within the 3 business days of receiving the

package. Replacement products are only shipped when the RMA is issued. NO

EXCEPTIONS.

Return Policy

Windster offers only the best and highest quality products. If you are not satisfied

with your purchase, please contact us within 3 business days of product arrival to

obtain a Return Merchandise Authorization (RMA). Returns sent without a RMA will

not be accepted. There will be a 25% re-stocking fee for every returned items.

Shipping fee will also be deducted from the original purchase price. When returning a

package, please include a copy of your purchase receipt. Use the original shipping

box and packing materials and completely remove or cover the original shipping label

Make sure that products are in brand new condition, uninstalled, un-drilled, and

contain everything that came with the package as when you first received it. If any

parts or manuals are missing, we have the right not to accept the return.

16

5101 Commerce Drive

Baldwin Park, CA 91706

TEL: [phone]

FAX: [phone]