Windsor Saber Cutter SCXC264, 10052430, 10052860, Saber Cutter SCX324, Saber Cutter SCXC324 Operator Instructions Manual
...
WALK BEHIND SCRUBBER
MODELS: SCX264 SCXC264 BSCSCX264
10052380 10052430 10052860
SCX324 SCXC324
10052390 10052440
Operating Instructions (ENG)
Instrucciones de funcionamiento (SPA)
86039080 - BP 01/24/13
PRV NO. 98964
IPX4
Read these instructions before using the machine
Lea las instrucciones antes de utilizar la máquina
MACHINE DATA LOG/OVERVIEW
Name: __________________________________________________________________________________________________
Address: _______________________________________________________________________________________________
Phone Number: _________________________________________________________________________________________
For the name and address of your dealer contact: Windsor Industries
MODEL _______________________________________
DATE OF PURCHASE __________________________
SERIAL NUMBER ______________________________
SALES REPRESENTATIVE # _____________________
DEALER NAME ________________________________
OPERATIONS GUIDE NUMBER ___________________
PUBLISHED
__________________________________________
YOUR DEALER
OVERVIEW
The Saber Cutter is a battery powered, self-propelled, hard floor scrubber intended for
commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor
with brushes or pads, and then vacuums the soiled water back into the recovery tank.
Warranty Registration
Thank you for purchasing a Windsor product. Warranty registration is quick and easy.
Your registration will allow us to serve you better over the lifetime of the product.
To register your product go to:
www.windsorind.com/WarrantyRegistration.aspx
For customer assistance:
1-800-444-7654
2
CUTTER 24V 86039080 05/04/11
Machine Data Log/Overview.........................2
Table of Contents..........................................3
HOW TO USE THIS MANUAL
How to use this Manual.................................1-1
SAFETY
Important Safety Instructions........................2-1
Hazard Intensity Level. .................................2-2
Safety Label Location. ..................................2-3
OPERATIONS
Technical Specifications. ..............................3-1
How the Machine Works...............................3-3
Components..................................................3-4
Controls.........................................................3-5
Machine Operation........................................3-9
Pre-Run Machine Inspection......................3-9
Starting Machine........................................3-9
Emergency Stop Procedures.....................3-9
Filling the Solution Tank.............................3-9
Scrubbing................................................ 3-10
Emptying & Cleaning Tanks.................... 3-11
MAINTENANCE
Service Schedule.............................. ........ 4-1
Batteries........................................................4-3
Battery Maintenance..................................4-3
Checking Battery Specific Gravity..............4-4
Charging the Batteries...............................4-4
Changing Batteries. ...................................4-5
Battery Connections...................................4-5
Squeegee Blades..........................................4-6
Adjusting Squeegee......................................4-6
Replace or Rotate Rear Squeegee Blade.. ..4-6
Replace or Rotate Front Squeegee Blade. ..4-6
Adjusting Squeegee Pitch................. ........ ..4-7
Adjusting Rear Deflection. ................ ........ ..4-7
Replacing Aqua-Mizer Squeege Blades.......4-7
Scrub Brushes. .............................................4-8
Types.........................................................4-8
Replacing or Installing Scrub Brushes.......4-8
Float Shut-Off................................................4-8
Solution Strainer ...........................................4-9
Brush Motor Replacement............................4-9
TABLE OF CONTENTS
Traction Motor Brush Replacement.. .........4-10
Circuit Breaker.................................. .........4-10
Brush Shrouds & Brush Skirts.......... .........4-10
Vacuum Motors................................. .........4-11
Actuator Scrub Deck......................... .........4-12
Greasing Axles ................................. .........4-13
Machine Troubleshooting ................. .........4-14
GROUP PARTS LIST
Control Handle............................................ 5-1
Cover (Front) & Tank Mount....................... 5-3
Cover (Top) & Tank Mount......................... 5-5
Decal........................................................... 5-7
Electrical Panel........................................... 5-9
Lift Handle................................................... 5-11
Lift Handle Linkage..................................... 5-13
Recovery Tank............................................ 5-15
Scrub Brush/Pad Driver.............................. 5-17
Scrub Deck Aqua-Mizer-26in Scrubhead ... 5-19
Scrub Deck Aqua-Mizer-32in Scrubhead ... 5-21
Scrub Deck Motors..................................... 5-23
Scrub Deck Skirt-26in Scrubhead............... 5-25
Scrub Deck Skirt-32in Scrubhead............... 5-27
Scrub Deck Lift Linkage-26in Scrub Deck.. 5-29
Scrub Deck Lift Linkage-32in Scrub Deck.. 5-31
Scrub Deck Lift ........................................... 5-33
Solution....................................................... 5-37
Squeegee-26in Scrubhead......................... 5-41
Squeegee-32in Scrubhead......................... 5-43
Squeegee Lift Linkage (Lower)................... 5-45
Vacuum....................................................... 5-47
Wheels & Frame......................................... 5-49
Wiring-Battery............................................. 5-51
Wiring-Control Panel................................... 5-53
Wiring-Main Harness.................................. 5-55
Wiring-Schematic-SCX264, SCX324.......... 5-57
Wiring-Schematic-SCXC264, SCXC324 .... 5-58
Brake-Option............................................... 5-59
Emergency Stop-Option ............................. 5-61
Accessory Pump-Option............................. 5-63
Battery Charger- SCXC264, SCXC324...... 5-65
Suggested Spare Parts............................... 5-67
EC Declaration of Conformity..................... 5-68
Warranty..................................................... 5-70
CUTTER 24V 86039080 04/17/07
HOW TO USE THIS MANUAL
This manual contains the following sections:
- HOW TO USE THIS MANUAL
- SAFETY
- OPERATIONS
- MAINTENANCE
- PARTS LIST
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
Parts may be ordered from authorized Windsor
dealers.
When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside of
the front cover of this manual.
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
DEALER NAME ______________________________
OPERATIONS GUIDE NUMBER __________________
PUBLISHED ________________________________
Copyright 2002 Windsor Industries, Printed in USA
The model and serial number of your machine is on
the back panel of the machine.
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards are identified that could
result in product or personal injury, or severe injury
resulting in death.
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
- Batteries
- Scrub Brushes
- Adjusting Squeegee
- Scrub Deck Skirt
- Squeegee Blade/Brush Head Options
- Service Schedule
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
- REF – column refers to the reference
number on the parts illustration.
- PART NO. – column lists the part
number for the part.
- PRV NO. – reference number.
- QTY – column lists the quantity of the
part used in that area of the machine.
- DESCRIPTION – column is a brief
description of the part.
- SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs. If
column has an asterisk (*), call
manufacturer for a serial number.
- NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
1-1
CUTTER 24V 86039080 04/17/07
IMPORTANT SAFETY INSTRUCTIONS
!
When using an battery powered appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
WARNING:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and
attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
This machine is not suitable for picking up hazardous dust.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
Disconnect battery before cleaning or servicing.
Before the machine is discarded, the batteries must be removed and properly disposed of.
Make sure all warning and caution labels are legible and properly attached to the machine.
During operation, attention shall be paid to other persons, especially children.
Before use all covers and doors shall be put in the positions specified in the instructions.
When leaving unattended, secure against unintentional movement.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.
Only chemicals recommended by the manufacturer shall be used.
This appliance has been designed for use with the brushes specified by the manufacturer. The fitting
of other brushes may affect its safety.
Do not use on surfaces having a gradient exceeding 2% unless the optional parking brake is installed
on the machine.
SAVE THESE INSTRUCTIONS
CUTTER 24V 86039080 04/17/07
2-1
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use Windsor approved replacement parts.
! WARNING
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep
top cover in raised position when charging. Keep sparks and flames away from the batteries. Do
not smoke around batteries.
! WARNING
Disconnect batteries before working on machine. Only qualified personnel should work inside
machine. Always wear eye protection and protective clothing when working on or near batteries.
Avoid skin contact with the acid contained in the batteries.
! WARNING
Never allow metal to lie across battery tops.
2-2
CUTTER 24V 86039080 04/17/07
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become
illegible, promptly replace them.
SAFETY DECAL
86252530
PRV NO. 81494
BATTERY CAUTION
86252520
PRV NO. 80885
SEE MANUAL
2% GRADE WARNING
CUTTER 24V 86039080 04/17/07
CIRCUIT BREAKER DECAL
86243530
PRV NO. 500565
2-3
TECHNICAL SPECIFICATIONS
ITEM DIMENSION/CAPACITY
Nominal power 1450 W
Rated Voltage 24VDC
Rated Amperage 60 Amps
Batteries 4 X 6 Volt 250-305-335AH @ 20 hr
rate
Scrub Brush Motors 2 X .75 hp (0.56 kW)
Vacuum Motor .75 hp (0.56 Kw)
Propelling Motor .3 hp (0.22 Kw)
Mass (GVW) 915 lbs. (415 kg) with 335 AH
Weight empty without batteries 346 lbs. (157 kg)
Solution Control Gravity feed, fully variable with
automatic shut-off in neutral
Solution tank capacity 23 gal. (87 l)
Recovery tank capacity 25 gal. (95 l)
Scrub brush diameter for 26 in. (66 cm) scrub head 13 in (33.0 cm)
Scrub brush diameter for 32 in. (81 cm) scrub head 16 in (41 cm)
Scrub brush pressure Actuated 0 lbs to 150 lbs (0 kg to 68
kg)
Scrub brush speed 200 rpm
Tires 2 x 10 in (25.4 cm) non-marking
foam-filled
Casters 2 X 4 in (10.2 cm) polyurethane solid
non-marking
Foundation Pressure (at recommended tire psi) 21 lbs./in 2 (140 kPa)
Maximum Speed 3.2 Miles/hour (5.2 km/hour)
Frame Construction Steel plate with epoxy powdercoat
finish.
Brakes (optional) Tire lock parking brake.
Minimum aisle u-turn width with 26 in. (66 cm) scrub head 64 in. (163 cm)
Minimum aisle u-turn width with 32 in. (81 cm) scrub head 69 in. (175 cm)
Maximum rated climb and descent angle with empty tanks and
without optional parking brake
Maximum rated climb and descent angle with full tanks and
without optional parking brake
2%
2%
3-1
CUTTER 24V 86039080 01/20/12
TECHNICAL SPECIFICATIONS
ITEM MEASURE
Height 45 in. (114 cm)
Length with 26 in. (66 cm) scrub head 64 in. (163 cm)
Length with 32 in. (81 cm) scrub head 66 in. (167 cm)
Width without squeegee and scrub head 24 in. (61 cm)
Width of squeegee for 26 in. (66 cm) scrub head 35 in. (89 cm)
Width of squeegee for 32 in. (81 cm) scrub head 39 in. (99 cm)
Width of scrub path for 26 in. (66 cm) scrub head 26 in. (66 cm)
Width of scrub path for 32 in. (81 cm) scrub head 32 in. (81 cm)
Length
SPECIAL NOTES:
The sound pressure level at the operator’s ear was
measured to be 72 dBA. This was a nearfield,
broad-band measurement taken in a typical industrial
environment on a tile floor. This appliance contains
no possible source of impact noise. The
instantaneous sound pressure level is below 63 Pa.
The weighted root mean square acceleration at the
operator’s arms was measured to be below 2.5m/s
This was a tri-axial, third-octave-band measurement
made during normal operation on a composite tile
floor. The measurement and related calculations
were made in accordance with ANSI S3.34-1986.
2
.
Width
Height
CUTTER 24V 86039080 04/17/07
3-2
HOW THE MACHINE WORKS
The Saber Cutter is a battery powered, selfpropelled, hard floor scrubber intended for
commercial use. The appliance applies a
cleaning solution onto a hard floor, scrubs the
floor with brushes, and then vacuums the soiled
water back into the recovery tank.
The machine's primary systems are the solution
system, scrub system, recovery system, and
directional control system.
The function of the solution system is to store
cleaning solution and deliver it to the scrub
system. The solution system consists of the
solution tank, strainer, valve and controls. The
solution tank stores cleaning solution (water and
detergent) until it is delivered to the scrub system.
The strainer protects the valve from debris. The
valve is a solenoid type valve, which controls the
delivery of cleaning solution to the scrub system.
The valve automatically prevents solution flow
unless the scrub brushes are turned on and the
machine is being propelled. The solution control
knob controls the amount of cleaning solution
delivered to the scrub system by controlling the
amount of time the valve is open.
The function of the scrub system is to scrub the
floor. The scrub system consists of two rotary
type disk scrub brushes, motors, scrub deck skirt,
lift mechanism and controls. The brushes scrub
the floor and the motors drive the brushes. The
brush drive hubs allow the scrub brushes to follow
irregularities and changes in the floor without
loosing contact with floor. The scrub deck skirt
controls the cleaning solution on the floor so that
the squeegee can pick it up. The brush lift
mechanisms are controls used to raise and lower
the deck.
3-3
CUTTER 24V 86039080 04/17/07
The function of the recovery system is to vacuum
the soiled water back into the recovery tank. The
recovery system consists of the squeegee,
vacuum motor, float ball filter, recovery tank and
controls. The squeegee wipes the dirty solution
off the floor as the machine moves forward. The
vacuum motor provides suction to draw the dirty
solution off the floor and into the recovery tank.
The recovery tank stores the dirty solution. The
float ball filter protects the vacuum fan from debris
and shuts off air going to the recovery tank when
tank is full. When flow of air is shut off the vacuum
motor will continue to run. At this time the
recovery tank must be drained.
The function of the directional control system is to
control the direction and speed of the machine.
The directional control system consists of the
propel control buttons, reverse button, speed
control knob/potentiometer, controller and
transaxle. The propel controls actuate switches
which cause the machine to move forward. For
reverse motion depress the reverse button while
depressing one of the propel controls. The speed
control knob actuates a potentiometer, which
signals speed. The controller interprets the
forward/reverse signals from the switches and the
speed signal from the potentiometer to command
the transaxle to propel the machine in the
direction, and at the speed, desired.
12
14
COMPONENTS
3
7
11
9
8
1. Control Panel
2. Front Cover
3. Recovery Tank
4. Recovery Tank Drain Hose
5. Scrub Head Shrouds
6. Solution Tank
7. Solution Tank Cover
8. Solution Tank Drain Hose
9. Solution Strainer
10. Squeegee
11. Aqua-Mizer
12. Top Cover
13. Vacuum Motor
14. Recovery Tank Dome
15. Accessory Pump Port (Optional)
10
1
6
15
13
4
2
5
CUTTER 24V 86039080 04/17/07
3-4
CONTROLS
15
6
8
3
13
7
2
5
9
16
12
1
4
10
14
3-5
11
CUTTER 24V 86039080 04/17/07
CONTROLS
6
1. Key Switch
2. Emergency Shut Off Switch (Optional)
3. Speed Control Knob
4. Propel Control Lever
5. Reverse Button
6. Brush Switch
7. Actuator Switch
8. Solution Control Knob
9. Vacuum Switch
1. KEY SWITCH
Controls the power for machine functions.
To turn machine on, rotate key clockwise.
To turn machine off, rotate key
counterclockwise.
FOR SAFETY: Always remove the key
when machine is unattended or during
service to prevent unauthorized
movement.
2. EMERGENCY SHUT-OFF SWITCH
(OPTIONAL)
Shuts off machine.
To shut off machine, push the switch.
To restart machine, rotate the switch
clockwise.
3. SPEED CONTROL KNOB
Controls the speed of the machine.
To increase speed, rotate knob clockwise.
To decrease speed, rotate knob
counterclockwise.
CUTTER 24V 86039080 04/17/07
10. Squeegee Lift Lever
11. Squeegee Pitch Adjustment Knob
12. Squeegee Deflection Adjustment Knobs
13. Battery Charge Level Indicator
14. Parking Brake (Optional)
15. Hour Meter (Optional)
16. Brush Pressure Indicator
4. PROPEL CONTROL LEVERS
Controls the machine direction, and scrub
brushes and solution flow.
To propel machine forward, squeeze either
propel lever.
The scrub brushes will not rotate and the
solution will not flow to scrub deck with the
propel levers in neutral.
5. REVERSE BUTTON
Controls the reverse function.
To propel machine backward, push the
reverse button while squeezing either propel
lever.
6. BRUSH SWITCH
Controls the scrub brush motors.
To turn scrub brushes on, press the bottom of
the switch. The brushes will not rotate with the
propel control levers in neutral.
To turn scrub brushes off, press the top of the
switch.
3-
CONTROLS
7. ACTUATOR SWITCH
Adjusts the amount of brush pressure to the
floor by raising or lowering the scrub deck.
To increase brush pressure, press the bottom
of the switch.
To decrease brush pressure or rise the scrub
deck, press the top of the switch.
8. SOLUTION CONTROL KNOB
Controls solution flow to scrub deck.
To increase flow, rotate knob clockwise.
To decrease flow, rotate knob counterclockwise.
If the brush motors are turned off or the propel
control levers are in neutral, the flow is
automatically interrupted until the motors are
turned on again. This feature prevents
unintentional draining of the solution tank and
allows the operator to adjust the solution flow to
the scrub deck without resetting each time the
scrubbing operation is interrupted.
9. VACUUM SWITCH
Controls the vacuum motor.
To start vacuum motor, press the bottom of the
switch.
To stop vacuum motor, press the top of the
switch.
10. SQUEEGEE LIFT LEVER
Raises and lowers the squeegee.
To lower the squeegee, lift the lever from its
raised position.
To raise the squeegee, lift the lever from its
lowered position.
11. SQUEEGEE PITCH ADJUSTMENT KNOB
Adjusts the deflection at the ends of the
squeegee.
To increase squeegee blade deflection at the
ends, turn knob counterclockwise.
To decrease squeegee blade deflection at the
ends, turn knob clockwise.
12. SQUEEGEE DEFLECTION ADJUSTMENT
KNOBS
Adjusts the deflection along the entire length of
the squeegee.
To increase squeegee blade deflection along the
entire length, turn the two knobs at the
squeegee ends counter-clockwise.
To decrease squeegee blade deflection along
the entire length, turn the two knobs at the
squeegee ends clockwise.
3-7
CUTTER 24V 86039080 04/17/07
13. BATTERY CHARGE LEVEL INDICATOR
Indicates the charge level of the batteries.
The meter display is divided into 10 vertical
bars. Bar illuminated on the far right indicate
full charge. Bars flashing near the left side
indicate the batteries should be recharged.
Further operation of the machine could
damage the machine or the batteries.
When the machine is left overnight with less
than a full charge, the display may initially
indicate a full charge. It will also indicate a full
charge if the batteries are disconnected, then
reconnected. After a few minutes of operation
the meter will give the correct charge level.
14. PARKING BRAKE (OPTIONAL)
Locks front wheels to prevent unintentional
movement.
To set parking brake, push down to lock notch.
To release parking brake, push down and over
out of the lock down notch.
15. HOUR METER (OPTIONAL)
Records the number of hours the machine has
been in operation. This information is useful
in determining when to service the machine.
16. BRUSH PRESSURE INDICATOR
The brush pressure indicator corresponds to
the amp draw of the scrub brush motors to tell
how hard the motors are working. The green
zone indicates medium or proper operating
brush pressure. The red zone indicates heavy
or excessive brush pressure. Operating in the
red zone may cause the brush circuit breakers
to trip.
CONTROLS
CUTTER 24V 86039080 04/17/07
3-8
MACHINE OPERATION
PRE-RUN MACHINE INSPECTION
Do a pre-run inspection to find possible problems that
could cause poor performance or lost time from
breakdown. Follow the same procedure each time to
avoid missing steps.
NOTE: See maintenance section for pre-run machine
inspection checklist items.
STARTING MACHINE
NOTE: Perform pre-run machine check before
operating machine.
FOR SAFETY: Before starting machine, make
sure that all safety devices are in place and
operating properly.
1. Turn the machine power on.
2. Release the parking brake, if your machine is
equipped with this option.
3. Engage the direction propel levers for the desired
direction.
EMERGENCY STOP PROCEDURES
1. Release the propel levers.
2. Turn machine power off with key switch.
3. If an electrical problem is suspected push in
emergency stop button, if machine is equipped
with this option.
4. Apply brakes, if your machine is equipped with
this option.
FILLING SOLUTION TANK
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
1. Turn the machine power off.
2. Set the parking brake if your machine is equipped
with this option.
3. Remove solution tank cover.
4. Fill the solution tank with clean water, leaving
enough room for the required amount of cleaning
solution. The solution tank capacity filled to 2” (5
cm) from bottom of fill inlet is 23 gallons (87 liters).
The water must not be hotter than 140° F (60°C)
to prevent damage to the tank.
5. Measure the chemical into the solution tank.
Liquid chemicals should be added to the solution
tank after filling with water. Dry chemicals should
be thoroughly mixed before being added into
solution tank. Commercially available, high
alkaline floor cleaners, are suitable for use in the
solution system.
NOTE: Read the chemical manufacturers
recommended proportion instructions.
6. Replace solution tank cover.
! WARNING
Flammable materials can cause an explosion or
fire. Do not use flammable materials in the tanks.
3-9
CUTTER 24V 86039080 04/17/07
NORMAL SCRUBBING
Plan the scrubbing pattern in advance. The
longest track is around the perimeter of the area
to be cleaned. For efficient operation, the runs
should be the longest possible without
stopping, or raising and lowering scrub
deck/squeegee.
NOTE: In order to achieve the best possible
results, the area which is to be cleaned should be
swept before scrubbing. Large debris, strings &
wire must be removed to prevent being caught in
brushes or squeegee.
turning,
CUTTER 24V 86039080 04/17/07
MACHINE OPERATION
TO BEGIN SCRUBBING
! WARNING
When operating the machine around people, pay
close attention for unexpected movement. Use
extra caution around children.
! CAUTION
Flammable liquids and/or reactive metals can
cause explosions or fire! Do not pick up.
1. Turn the machine power on.
2. Lower the squeegee.
3. Turn the vacuum on.
4. Lower the scrub brushes to the floor.
5. Turn the scrub brushes on (brushes will start
when machine is propelled).
6. Drive machine forward to begin scrubbing.
NOTE: Shut machine off immediately if water or
foam is expelled from the machine.
7. Adjust the speed of the machine, solution flow
and scrub brush pressure as necessary.
NOTE: Once solution flow rate is set it is not
necessary to shut off solution when stopping
scrubbing. Solution flow is automatically shut off
when brush motors stop. When brush motors are
activated, flow automatically resumes.
TO STOP SCRUBBING
1. Release the propel levers.
2. Turn the scrub brushes off.
3. Raise the scrub brushes.
4. Raise the squeegee.
5. Turn the vacuum off.
6. Turn the machine power off.
3-10
MACHINE OPERATION
DOUBLE SCRUB
For floors which are heavily soiled or have thick
accumulations of floor finish may not clean
sufficiently with one pass. In these cases it will be
necessary to double scrub.
To double scrub, make the first pass over the
surface being cleaned with the squeegee up,
vacuum off, the solution on, Aqua-Mizer removed
and brushes down. This allows the
contact with the soil while loosening the surface
accumulation with the brushes. Allow time for the
first application to stay in contact with the floor.
Length of time between the first and second pass
depends on amount of accumulation and the type of
chemical being used. A second scrubbing with the
squeegee down and again the solution and brushes
on will further loosen soil. The additional application
of solution will further assist the difficult cleaning job.
FOR SAFETY: When using machine, go slow on
inclines and slippery services.
EMPTYING AND CLEANING TANKS
1. Park the machine next to a floor drain. Drain
hose is on left rear corner of the machine.
2. Turn the machine power off and set parking
brake, if your machine is equipped with this
option.
SOLUTION TANK
1. Loosen small drain hose from the retainer, then
lower hose in direction of the drain.
2. Remove the solution tank cover.
3. Flush the solution tank out with clean water and
run several gallons of clean water through
systems. Do not use water hotter than 140°F
(60°C) to clean tank. Damage may occur.
NOTE: Never allow solution to remain in tank.
Damage to tank, seals and valves could occur.
4. Secure drain hose into the retainer.
3-11
solution to stay in
CUTTER 24V 86039080 04/17/07
RECOVERY TANK
1. Unhook the large drain hose from the retainer.
Unscrew the T-handle on plug enough to loosen
plug, then lower hose in direction of the drain.
Do not stand in front of end of hose. Recovered
solution will come out with force. Slowly remove
plug from drain hose.
2. Remove the recovery tank dome. Flush the
recovery tank out with clean water. Do not use
water hotter than 140°F (60°C) to clean tank.
Damage may occur.
3. Clean off the float shut-off system and inspect
for free movement of float. The float shut-off
system is located in the rear of the recovery
tank.
4. Replace the drain plug and secure drain hose in
bracket.
5. If machine is to be stored, leave the recovery
tank dome off.
SOLUTION
TANK COVER
RECOVERY
TANK COVER
SOLUTION
TANK DRAIN
RECOVERY
TANK DRAIN
SERVICE SCHEDULE
MAINTENANCE DAILY WEEKLY MONTHLY 100
Check batteries after charging; add water if necessary
Check pad wear to prevent buildup of chemicals
Check linkages and connectors for wear and damage
Check hoses for wear, blockages, or damage
Clean squeegee; check for adjustment; inspect for wear
Check handles, switches, knobs, domes, and gaskets for
damage
Clean out recovery tank
Clean out solution tank; remove and clean screen
Clean outside of all tanks; check for damage
Run vac motor for at least one minute to allow motor to dry
Store with dome off tank to allow the tank to dry
Check scrub deck skirt
Check batteries for corrosion, cracks and evidence of
overheating
Check all bearings for noise
Check all gaskets for wear and leakage
Check vac motor carbon brushes
Check brushes for wear; ensure bristles are not damaged
Check linkages for wear and damage
Grease transaxle
Grease wheels and casters
Check squeegee blades for wear and frame for damage
Check overall performance of machine
Clean batteries and terminals
Check parking brake (inspect cables, linkages and pulleys)
Check carbon brushes in all vacuum, brush drive, and propel
motors
Blow out dust in motors
Inspect motor commutators
Clean chains, cables and pulleys
Clean pivot points on squeegee and scrub deck linkages
MAINTENANCE
200
HRS
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
HRS
*
CUTTER 24V 86039080 04/17/07
4-1
MAINTENANCE
6
8
1. Batteries
2. Squeegee
3. Aqua Mizer
4. Scrub Brushes
5. Float Shut-Off
6. Solution Strainer
7. Brush Motor
8. Traction Motor
9. Circuit Breakers
10. Brush Shroud & Brush Skirts
11. Vacuum Motor
12. Actuator Scrub Brush
5
9
2
11
3
4
1
12
7
10
4-2
CUTTER 24V 86039080 04/17/07
1. BATTERIES
The batteries provide the power to operate the
machine. The batteries require regular maintenance
to keep them operating at peak efficiency.
The machine batteries will hold their charge for long
periods of time, but they can only be charged a
certain number of times. To get the greatest life
from the batteries, charge them when their charge
level reaches 25% of a full charge. Use a
hydrometer to check the charge level.
Do not allow the batteries to remain in a discharged
condition for any length of time. Never expose a
discharged battery to temperatures below freezing.
Discharged batteries will freeze causing cracked
cases. Do not operate the machine if the batteries
are in poor condition or if they have a charge level
below 25% (specific gravity below 1.155).
Keep all metallic objects off the top of the batteries,
as they may cause a short circuit. Replace worn or
damaged cables and terminals.
Check the electrolyte level in each battery cell
before and after charging the batteries. Never add
acid to the batteries, use distilled water. Do not
allow water level to fall below the battery plates.
Portions of plates exposed to air will be destroyed.
Do not overfill. Keep plugs firmly in place at all
times.
MAINTENANCE
! CAUTION
When servicing machine, avoid contact with
battery acid.
! WARNING
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
! WARNING
Wear eye protection and protective clothing
when working with batteries.
! WARNING
Charge batteries in a well ventilated area.
BATTERY MAINTENANCE
1. When cleaning the batteries, use a solution of
baking soda and water. Do not allow the
cleaning fluid to enter the battery cells,
electrolyte will be neutralized.
2. Maintain the proper electrolyte level in each
battery cell. If a cell should accidentally
overflow, clean immediately.
3. Wipe off the top of the batteries at least once a
week.
4. Test battery condition with a hydrometer at least
once a week.
5. Ensure that all connections are tight and all
corrosion removed.
6. Every 4 to 6 months, remove that batteries from
the machine and clean the battery cases and
battery compartment.
CUTTER 24V 86039080 04/17/07
4-3
MAINTENANCE
CHECKING BATTERY SPECIFIC GRAVITY
Use a hydrometer to check the battery specific
gravity.
CHECKING GRAVITY
A. Hydrometer
B. Battery
NOTE: Do not take readings immediately after
adding distilled water, if the water and acid are not
thoroughly mixed, the reading may not be accurate.
Check the hydrometer readings against this chart.
SPECIFIC GRAVITY
@ 80
NOTE: If the readings are taken when the battery
electrolyte is any temperature other than 80
°C), the reading must be temperature corrected.
(27
To find the corrected specific gravity reading when
the temperature of the battery electrolyte is other
than 80
reading 0.004 (4 points), for each 10
80
Subtract (-) from the specific reading 0.004 (4
points), for each 10
°F (27°): Add (+) to the specific gravity
° (27°C).
4-4
Battery Check
BATTERY CONDITION
°
F (27°C)
1.265 100% CHARGED
1.225 75% CHARGED
1.190 50% CHARGED
1.155 25% CHARGED
1.120 DISCHARGED
°F
°F (6°C) above
°F (6°C) below 80°F (27°C).
CUTTER 24V 86039080 04/17/07
TO CHARGE THE BATTERIES
! WARNING
When servicing machine, avoid contact with
battery acid.
! CAUTION
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
! WARNING
Wear eye protection and protective clothing
when working with batteries.
! WARNING
Charge batteries in a well ventilated area. Leave
the battery cover open.
Use a 24 volt, 18 amp maximum output or 25 amp
(depending on the size of the batteries), DC charger
which will automatically shut off when the batteries
are fully charged.
1. Stop the machine in a clean, well ventilated area
next to the charger.
2. Turn “OFF” machine.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
3. Raise the battery cover.
! WARNING
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
4. Check the electrolyte level in each battery cell.
Before charging, add just enough distilled water
to cover the plates. After charging is complete,
add just enough distilled water to bring up the
level to the indicator ring. If the water level is
too high before charging, normal expansion rate
of the electrolyte may cause an overflow.
Resulting in a loss of battery acid balance and
damage the machine.
5. Replace the battery caps, and leave them in
place while charging.
6. Unplug the battery connector from the machine.
FOR SAFETY: When charging, connect the
charger to the batteries before connecting the
charger to the AC wall outlet. Never connect the
charger to the AC wall outlet first. Hazardous
sparks may result.
7. Plug the charger connector into the battery
connector. Connect the charger AC plug to a
wall outlet. The charger gauge should indicate
that the batteries are charging.
8. When the batteries are fully charged, disconnect
the charger from the AC wall outlet, then
disconnect the charger from the batteries.
9. Connect the batteries to the machine connector.
10. Check the electrolyte level. It should be up to
the indicator ring. If necessary, add distilled
water.
11. Lower the battery cover.
Machines equipped with Onboard Charger:
1. Connect charger’s AC power cord to AC mains.
The charger’s YELLOW “AC” LED will light.
Note: When charger is energized, all machine
function will shut down.
2. Current level being delivered to the batteries will
be displayed on the charger’s bar graph.
3. When battery charge level has reached 80% the
YELLOW “80%” LED will light.
4. Batteries will then receive a low current “finishcharge” indicated by the flashing GREEN
“100%” LED.
5. Charging cycle is complete when “100%” LED is
continuously GREEN.
6. Disconnect charger’s AC power cord.
7. Raise battery cover and check the battery
electrolyte level. It should be up to the indicator
ring. If necessary, add distilled water.
8. Lower the battery cover.
Note: For additional information about battery
charger function, please see the charger Product
Manual.
CUTTER 24V 86039080 04/17/07
MAINTENANCE
CHANGING BATTERIES
Stop the machine in a clean area next to the
charger. Turn off machine.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn off machine
and remove key.
1. Raise the battery cover.
2. Disconnect battery pack from machine.
3. Use the proper size open end wrench to
disconnect main ground wire first and secure
cable terminal away from batteries.
4. Disconnect main positive lead and secure cable
terminals away from batteries.
5. Loosen both terminals on each jumper cable
and remove one at a time.
6. Prepare a suitable site to place the batteries.
7. Attach suitable battery lifting device and lift
batteries from the machine.
!
WARNING
Batteries are a potential environmental hazard.
Consult your battery supplier for safe disposal
methods.
BLK
BLK
+
RED
BLK
-
+
RED
-
+
RED BLK
-
-
BLK
RED
REDRED
-
+
-
BLK
++
FRONT OF MACHINE
4-5
MAINTENANCE
2. SQUEEGEE BLADES
The front squeegee blade allows solution to pass
through channels in the blade into the squeegee
assembly while maintaining vacuum to provide lift.
The front blade has four wear surfaces and can be
rotated for extended life. The front blade should not
require regular replacement under normal use.
The rear blade wipes the floor to a near dry
condition. It is important the rear blade be in good
condition to properly do its job. As with the front,
each squeegee blade assembly has four wear
surfaces for extended service.
Check both the front and rear squeegee blades for
damage, wear, and adjustment each day in the prerun check. Change the front blade if it is torn or has
an uneven edge. Change the rear blade if it is less
than 1/2 the original thickness.
ADJUSTING SQUEEGEE
Adjusting the squeegee is a two-part process. First,
the squeegee assembly must have correct pitch in
order for the squeegee blade to have the same
deflection at each tip as well as the center. The
knob on the squeegee linkage controls the pitch
adjustment. The second adjustment is the
deflection. Knobs on each end of the squeegee
control this.
CORRECT
NOT ENOUGH
SQUEEGEE SIDE VIEW OF
4-6
SQUEEGEE DEFLECTION
TOO MUCH
CUTTER 24V 86039080 04/17/07
TO REMOVE SQUEEGEE ASSEMBLY
1. With the squeegee in the up position, turn key
switch “OFF”.
2. Disconnect vacuum hose from squeegee and
loosen both knobs.
3. Pull squeegee assembly rearward from the
lifting carrier.
4. Inspect or repair as necessary and reinstall.
TO REPLACE OR ROTATE REAR
SQUEEGEE BLADES
1. With the squeegee in the up position, turn key
switch “OFF”.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
2. Remove the squeegee assembly from the
machine. Unlatch and remove blade retainer
strap and remove squeegee blade.
3. Rotate the squeegee to new edge position or
replace as required. Each blade has four new
edge positions.
4. Install blade on locating pins of squeegee
assembly.
5. Install squeegee retainer strap.
6. Fasten and lock latch, adjust latch only tight
enough to take up slack in retaining strap.
TO REPLACE OR ROTATE FRONT
SQUEEGEE BLADE
1. With the squeegee in the up position, turn key
switch “OFF”.
2. Remove the squeegee from the machine.
Loosen three thumbscrews and remove the
retainer strap and squeegee blade.
3. Rotate the squeegee to new edge position or
replace as required. Each blade has four new
edge positions. When installing the front blade,
tighten the center thumbscrew first. Insure that
the retainer strap is pressed against the blade
before tightening the outer screws.
7
TO ADJUST SQUEEGEE PITCH
1. Choose a smooth, level surface. Turn “ON” the
key switch. Lower the squeegee and drive
forward at least 2 feet (60cm.).
2. With the squeegee down, stop the machine. Do
not allow machine to roll back.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn off machine
and remove key.
3. Determine the differences, if any, in deflection of
the squeegee blade between each end and the
middle. Proper adjustment is obtained when
deflection is equal all the way across the
squeegee blade. The bubble level should also
indicate when the squeegee is adjusted
properly. When the air bubble is in the center of
the vial, the deflection should be even across
the squeegee blade.
4. To decrease the deflection of the squeegee
blade at the ends, tighten knob near the
squeegee center. To increase the deflection at
the ends of the squeegee assembly, loosen
knob.
5. Check the deflection of the squeegee blades
again. Repeat steps 1 through 4 until the
deflection is equal across the entire rear
squeegee blade.
3/8”
PROPER DEFLECTION OF SQUEEGEE BLADE
CUTTER 24V 86039080 04/17/07
MAINTENANCE
TO ADJUST AMOUNT OF REAR
SQUEEGEE DEFLECTION
1. Choose a smooth, level surface. Lower the
squeegee and drive forward at least 2 feet
(60cm).
2. With the squeegee down, stop the machine. Do
not allow machine to roll back.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
3. Observe the amount of squeegee deflection. It
should deflect 3/8 in. (9.5mm) across the entire
width of the squeegee.
4. To increase the squeegee deflection, turn the 2
knobs at the squeegee ends counter-clockwise.
To decrease the deflection, turn the knobs
clockwise.
NOTE: The deflection should be consistent along
the length of the squeegee. If the deflection varies
from end to end the knobs can be adjusted
independently to correct the variation.
5. Turn on the key switch. Raise, then lower
squeegee assembly. Drive forward at least
2 feet (60cm).
6. Repeat steps 2 through 4 until deflection of
3/8 in. (9.5mm) is reached.
3. TO REPLACE AQUA-MIZER
SQUEEGEE BLADES
These squeegee blades have two wear edges. To
use the second edge:
1. Remove deck shrouds.
2. Remove brushes or pad drivers.
3. Remove each of the Aqua-Mizer squeegee
systems.
4. Remove the hardware from each system that
retains the blade.
5. Flip the blades and replace hardware.
6. Re-install each Aqua-Mizer system, brushes or
pad drivers and shrouds.
4-
MAINTENANCE
4. SCRUB BRUSHES
There are four different types of brushes available to
cover applications from cleaning heavily soiled floors
to polishing. A pad driver is also available to take
advantage of the many cleaning pads on the market.
Please refer to the following to assist in selecting the
proper brush or pad for the work at hand.
UNCOATED FLOORS
Aggressive Grit is a nylon fiber impregnated with
silicone carbide grit. It grinds away stain, soil, and
removes surface material.
Mild Grit is a less aggressive silicone carbide grit
suitable for cleaning medium soil conditions.
Advantages are faster ground speed than nylon
bristles on light solid applications.
Polypropylene is a general-purpose scrub brush
with stiff bristles. Polypropylene works well for
maintaining concrete, wood and tile floors.
FINISHED FLOORS
Nylon bristles are used in a variety of applications
on coated or uncoated surfaces.
White Pads (Polishing) are used for dry polishing to
achieve a high-gloss appearance, or surface
washing on highly polished or burnished floors.
Red Pads (Buffing) are used for light-duty
scrubbing. When used with a mild detergent they
will provide surface cleaning without removing the
finish.
Blue Pads (Scrubbing) are used for heavy-duty
scrubbing and light stripping. The blue pads remove
less finish than brown stripping pads, yet will remove
black marks, stains and dirt.
Black Pads (Stripping) are used for easy and
complete removal of old floor waxes/finishes. They
will quickly remove ground in dirt, black heel marks,
and spills. When used with the proper stripper, this
pad leaves the floor clean and ready for finishing.
The scrub brushes should be checked before each
days work for wire, string, wear and damage.
4-8
CUTTER 24V 86039080 04/17/07
REPLACING OR INSTALLING SCRUB
BRUSHES
1. With the scrub deck up, turn “OFF” the machine.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn OFF
machine and remove key.
2. Remove the two brush cover shrouds.
3. Locate release lever on top of brush or pad
driver. Rotate release lever counter-clockwise
and the brush/pad driver will release and drop
down.
4. To reinstall, center the brush driver under the
brush drive hub. Raise until it contacts brush
driver assembly. Turn clockwise until release
lever plate locks into position.
5. Replace the two brush cover shrouds.
NOTE: Check that release plate is completely
closed and pad/brush is securely attached. Damage
to driver or brush could occur.
5. RECOVERY TANK FLOAT SHUT-OFF
When water is no longer being vacuumed from
the floor and the vacuum fan is operating, the
ball float has engaged. The vacuum motor
will not vacuum water with recovery tank full.
The recovery tank must be drained.
1. The float shut-off screen can be cleaned in or
out of the machine.
2. To clean the float shut-off while it is inside the
machine wipe material off screen then rinse.
Check that the ball is also clean and moves
freely.
3. To remove the float shut-off, grasp the screen
with one hand and the connected tube with
the other. Tilt and pull the float screen
assembly to pull it off the barb on the tube.
To install, place one hand on the tube, and
then tilt and push the float screen assembly
over the barb on the tube.
6. SOLUTION STRAINER
The solution strainer is located in front of the left
front wheel. The solution strainer protects the
solenoid valve from debris. If there is little or no
solution flow to the ground, check the strainer for
debris. Drain the solution tank and clean the
solution strainer. To remove the strainer, turn the
bottom part of the strainer counterclockwise until
the bottom is separated. Clean out the debris
from the wire mesh and re-assemble. Make sure
the O-ring gasket is in place when re-assembled
7. BRUSH MOTOR
! WARNING
Do not use a pressure washer to clean around
the brush motors. Use tap pressure only.
CHANGING BRUSH MOTORS
1. With the scrub deck in the stored position,
disconnect brush motor wiring connector from
harness.
2. Remove shrouds from scrub deck to access and
remove scrub brushes or pad drivers.
3. Remove retaining bolt, lock washer, flat washer
and star drive from brush motor shaft.
4. Remove 4 brush motor mounting bolts located
under scrub deck.
5. Remove brush motor.
6. Reverse steps to install.
MAINTENANCE
BRUSH MOTOR CARBON BRUSH
REPLACEMENT
1. Scribe alignment mark on motor barrel to motor
cap. Remove two bolts.
2. Remove end cap from motor.
NOTE: Motors contain two wave washers in cap.
Do not lose these.
3. Release brus h from spring tension. Remove
screw connecting brush wire lead to brush
holder. Clean brush holder to insure free
movement.
4. Retract spring and install new brush. Install
connector screw and lead.
5. When all new brushes are installed. Place all in
retracted position, held into brush holder by
spring tension.
6. Carefully place end cap onto bearing on motor
shaft.
NOTE: Use care to assure wave washer
alignment.
7. With end cap in partially installed position,
release all brushes to contact position with
motor commutator.
NOTE: Failure to insure all brushes are
released will result in motor failure.
8. Reset end cap and realign with scribe marks
on motor barrel. Reinstall the two attach bolts
from cap into base.
9. Maintain alignment between motor barrel base
and cap.
CUTTER 24V 86039080 04/17/07
4-9
MAINTENANCE
8. TRACTION MOTOR
! WARNING
Do not use a pressure washer to clean around the
motors. Use tap pressure only.
TRACTION MOTOR CARBON BRUSH
REPLACEMENT
FOR SAFETY: Before leaving or servicing machine,
stop on a level surface, turn off machine and remove
key.
1. Disconnect batteries from machine.
2. Disconnect the electrical connection to the
traction motor.
3. Remove brush cap.
4. Release brush from spring tension. Remove
screw connecting brush wire lead to brush
holder. Clean brush holder to insure free
movement.
5. Install new brush and reinstall connecting screw
and lead.
6. When all new brushes are installed. Place all in
retracted position, held into brush holder by
spring tension.
7. Carefully replace brush cap.
4-10
CUTTER 24V 86039080 04/17/07
9. CIRCUIT BREAKERS
Circuit breakers interrupt the flow of power in
the event of an electrical overload. When a
circuit breaker is tripped, reset it by pressing
the exposed button. If a circuit breaker
continues to trip, the cause of the electrical
overload should be found and corrected.
30 Amp. Protects the left scrub
brush motor.
30 Amp. Protects the right scrub
25 Amp. Protects the propel
motor.
brush motor.
25 Amp. Protects the vacuum
motor.
3 Amp. Protects the machine
controls.
10. BRUSH SHROUDS & BRUSH SKIRTS
Contain the water in the shroud area. The skirt
will flex over uneven floors and also as the brush
or pad wears. As the brush wears the shrouds
can be adjusted so that skirt does not have to flex
so much.
Remove three bolts on each side that fasten the
bracket to the cover and re-assemble in the top
holes. When the brushes are replaced with new
ones move the covers back to the lower set of
holes.
11. VACUUM MOTOR
(Refer to the Vacuum Group in the parts section of
manual)
! WARNING
Do not use a pressure washer to clean around the
vacuum motors. Use tap pressure only. Care
must be taken so that water is not directed into
vacuum motor air intakes.
CHANGING VACUUM MOTOR
1. Remove side cover.
2. Disconnect electrical connector to the vacuum
motor.
3. Loosen clamp and disconnect hose from vacuum
intake.
4. Remove vacuum motor mounting bracket bolts,
which are located under frame.
5. Remove vacuum motor and mounting bracket
assembly.
6. Reverse steps to install
Vacuum Motor Carbon Brushes Replacement (Windsor)
End Cap
Carbon
Brushes
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Important:
These brushes wear quicker as the length shortens
due to increased heat. Spring inside brush housing
will damage motor if brushes are allowed to wear
away completely.
MAINTENANCE
Vacuum Motor Carbon Brushes Replacement (Ametek)
End Cap
Carbon
Brushes
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Note:
Place
stop in
groove.
Important:
These brushes wear quicker as the length shortens
due to increased heat. Spring inside brush housing
will damage motor if brushes are allowed to wear
away completely.
3/8 (9.5mm)
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.
3
[9.5mm]
8
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.
CUTTER 24V 86039080 04/17/07
4-11
12. ACTUATOR SCRUB DECK
REMOVAL/REPLACEMENT
FOR SAFETY: Before leaving or servicing
machine, stop on a level surface, turn off
machine and set parking brake (If option is
installed).
1. Remove front cover.
2. Remove the two nuts below the scrub deck that
attach the actuator bracket.
3. Remove clevis pin and rue ring from lower
bracket of actuator, make sure not allow actuator
bracket to rotate.
4. Disconnect actuator from wiring harness.
5. Remove upper clevis pin and rue ring from
actuator bracket.
6. Reverse steps to install.
MAINTENANCE
SCRUB DECK ACTUATOR ADJUSTMENT
The actuator will need to be adjusted when replaced.
To adjust the actuator:
1. While holding actuator barrel to prevent it from
spinning, apply power to the actuator such that it
is fully extended. Positive power to white wire,
and negative/ground to black. Limit switch within
actuator will stop it.
2. Turn barrel out one or more full turns to assure
that when it is retracted it will not bind against
itself.
3. While holding actuator barrel to prevent it from
spinning, apply power to the actuator such that it
is fully retracted. Positive power to black wire,
and negative/ground to white wire. Limit switch
within actuator will stop it.
4. With actuator fully retracted, turn barrel in until it
touches the base of the threaded shaft.
5. At the bottomed out position, turn the barrel out
1 1/2 turns, then enough more to allow
connection to lift linkage.
6. Connect actuator to lift linkage.
7. Check travel of actuator during operation.
4-12
CUTTER 24V 86039080 04/17/07
Loading...