Windsor RMBS12, RMBS16 User Manual

Operating Instructions (ENG)

MODELS: RMBS12 BEFORE S/N12236

RMBS16 BEFORE S/N 16905

J

980124 09/20/05

Read instructions before operating the machine.

MACHINE DATA LOG/OVERVIEW

2

YOUR DEALER

Address: _______________________________________________________________________________________________

MODEL _______________________________________
DATE OF PURCHASE __________________________
SERIAL NUMBER ______________________________

SALES REPRESENTATIVE # _____________________
DEALER NAME ________________________________
OPERATIONS GUIDE NUMBER ___________________

PUBLISHED __________________________________________

Copyright 2003 Windsor Industries, Printed in USA

Name: __________________________________________________________________________________________________

For the name and address of your dealer contact: Windsor Industries

Phone Number: _________________________________________________________________________________________

OVERVIEW

The Windsor Rombus Carpet Maintainer is designed to maintain your carpet using the Rombus
quick clean, quick dry carpet care system. The machine has two counter rotating brushes that help
scrub chemical into the carpet. The chemical, Red Carpet Rombus Carpet Clean Chemical,
encapsulates the dirt, allowing both to be vacuumed up once the chemical has dried. The brushes

also help to raise the pile of the carpet, giving it a lush groomed appearance.

ROMBUS 980124 07/02/03

TABLE OF CONTENTS

3

Machine Data Log/Overview.......................2

Table of Contents........................................3

HOW TO USE THIS MANUAL

How to use this Manual...............................1-1

SAFETY

Important Safety Instructions......................2-1

Hazard Intensity Level................................2-2

Grounding Instructions. ...............................2-3

OPERATIONS

Technical Specifications.............................3-1

How the Machine Works.............................3-2

Machine Operation......................................3-3

Pre-run Inspection...............................3-3

Starting Machine..................................3-3

Machine Shut-down and Storage........3-3

MAINTENANCE

GROUP PARTS LIST

Handle Group..............................................5-1

Base - Motor Group....................................5-3

Base - Brush Group....................................5-5

Notes...........................................................5-7

Warranty.....................................................5-8

Brush Cleaning and Maintenance...............4-1

Machine Maintenance.................................4-1

Daily Maintenance...............................4-1

Periodic Maintenance..........................4-1

Annual Maintenance............................4-1

Machine Troubleshooting............................4-2

ROMBUS 980124 07/02/03

HOW TO USE THIS MANUAL

This manual contains the following sections:

- HOW TO USE THIS MANUAL

- SAFETY

- OPERATIONS

- MAINTENANCE

- PARTS LIST

The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.

Parts may be ordered from authorized Windsor
dealers. When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside
of the front cover of this manual.

MODEL _____________________________________

DATE OF PURCHASE ________________________

SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
DEALER NAME ______________________________

OPERATIONS GUIDE NUMBER __________________

PUBLISHED ________________________________

Copyright 2002 Windsor Industries, Printed in USA

The PARTS LIST section contains assembled
parts illustrations and corresponding parts list. The
parts lists include a number of columns of
information:

- REF – column refers to the reference
number on the parts illustration.

- PART NO. – column lists the part
number for the part.

- QTY – column lists the quantity of the
part used in that area of the machine.

- DESCRIPTION – column is a brief
description of the part.

- SERIAL NO. FROM – column
indicates the first machine the part
number is applicable to. When the
machine design has changed, this
column will indicate serial number of
applicable machine. The main
illustration shows the most current
design of the machine. The boxed
illustrations show older designs. If
column has an asterisk (*), call
manufacturer for serial number.

- NOTES – column for information not
noted by the other columns.

NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.

The model and serial number of your machine is
on the operator’s left hand side, side panel of
base.

The SAFETY section contains important
information regarding hazard or unsafe practices
of the machine. Levels of hazards is identified that
could result in product or personal injury, or severe
injury resulting in death.

The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.

The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition.

NOTE: The 98# on the lower left corner of the front
cover is the part number for this manual.

ROMBUS 980124 07/02/03

IMPORTANT SAFETY INSTRUCTIONS

!

WARNING:

When using an electrical appliance, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

This machine is for commercial use.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet . See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before

maintenance or service.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near

children.
Use only as described in this manual. Use only manufacturer’s recommended components and

attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning

grounding the machine. If the machine is not working properly , has been dropped, damaged, left
outdoors, or dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord
around sharp edges or corners.

Do not run machine over cord or allow the rotating brushes to come in contact with the cord. Keep
cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical
cord.

Always use cable restraint provided and wind the cable around the cable holder on the handle. For
quick release of the electrical cable rotate the cable holder 180 degrees.

Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may

reduce airflow.
Machine is designed for indoor use only and must not be operate or stored outdoors in wet

conditions.

Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this

machine near flammable fluids, dust or vapors.
Only the brushes provided with the machine or those specified by the manufacturer can be used.

The intended use of the brushes is specifically for the cleaning of carpeting and should not be used
in any other way.

This machine is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

SAVE THESE INSTRUCTIONS

ROMBUS 980124 07/02/03

2-1

HAZARD INTENSITY LEVEL

!

WARNING

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

! CAUTION

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or

property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist.
Locate all safety devices on the machine. Please take the necessary steps to train the machine
operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use Windsor approved replacement parts.

.

ROMBUS 980124 07/02/03

2-2