AUTOMATIC SCRUBBER
MODELS: SCC172 QSCC172 SCHC172
HCC172 QSCC172IA
10066320 10066300 10066330
10066270 10066310
86221970-AA
01/06/12
IPX4
Read these instructions before using the machine
MACHINE DATA LOG/OVERVIEW
MODEL _______________________________________
DATE OF PURCHASE __________________________
SERIAL NUMBER ______________________________
SALES REPRESENTATIVE # _____________________
Name: ________________________________________________________________________________________________
Address: ______________________________________________________________________________________________
Phone Number: ________________________________________________________________________________________
YOUR DEALER
OVERVIEW
The Automatic Scrubber is a battery powered, hard floor scrubber intended for commercial
use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with a brush
or pad, and then vacuums the soiled water back into the recovery tank.
Warranty Registration
Thank you for choosing our product. Warranty registration is quick and easy.
Your registration will allow us to serve you better over the lifetime of the product.
http://warranty.karcherna.com/warrantyregistration.aspx
2
To register your product go to:
86221970 17” SCRUBBER 08/15/11
Machine Data Log/Overview................................2
Table of Contents.................................................3
HOW TO USE THIS MANUAL
How to use this Manual........................................1-1
SAFETY
Important Safety Instructions ...............................2-1
Hazard Intensity Level..........................................2-2
Safety Label Location...........................................2-3
OPERATIONS
Technical Specifications.......................................3-1
How the Machine Works......................................3-3
Components.........................................................3-4
Controls................................................................3-5
Machine Operation............................................. 3-7
Pre-Run Machine Inspection .......................... 3-7
Filling Solution Tank........................................ 3-7
Scrubbing. ....................................................... 3-7
Emptying & Cleaning Tanks............................ 3-8
MAINTENANCE
Batteries...............................................................4-1
Battery Maintenance.........................................4-1
Checking Battery Specific Gravity.....................4-2
Charging the Batteries. .....................................4-2
On-Board Charger Battery Selection................4-3
Changing Batteries............................................4-4
Battery Connections..........................................4-4
Scrub Brushes......................................................4-5
Types.................................................................4-5
Replacing or Removing Scrub Brushes............4-6
Installing Scrub Brushes...................................4-6
Squeegee Blades.................................................4-6
Replace Squeegee Blade.................................4-6
Remove Squeegee Assembly. .........................4-6
Service Schedule.................................................4-7
Machine Troubleshooting.....................................4-8
86221970 17” SCRUBBER 10/12/09
TABLE OF CONTENTS
PARTS LIST
Decal ..................................................................5-1
Control Panel-w/Charger....................................5-3
Control Panel-SCHC172 w/Charger ..................5-5
Control Panel-QSC172.......................................5-7
Hour Meter
Handle................................................................5-11
Recovery Tank ...................................................5-13
Scrub Brush/Pad Driver......................................5-15
Scrub Motor/Lift..................................................5-17
Solution Tank .....................................................5-19
Squeegee...........................................................5-21
Squeegee Lift.....................................................5-23
Vacuum..............................................................5-25
Wheel & Frame ..................................................5-27
Onboard Charger ...............................................5-29
Wiring – Battery Cables......................................5-31
Wiring – Main Harness – all except QSC172 &
SCHC172 ...........................................................5-33
Wiring – Main Harness – SCHC172...................5-35
Wiring – Main Harness QSC172........................5-37
Wiring – Schematic – all except QSC172 &
SCHC172 ...........................................................5-39
Wiring – Schematic – SCHC172........................5-40
Wiring – Schematic – QSC172 ..........................5-41
Suggested Spare Parts......................................5-42
.........................................................5-9
3
HOW TO USE THIS MANUAL
This manual contains the following sections:
- HOW TO USE THIS MANUAL
- SAFETY
- OPERATIONS
- MAINTENANCE
- PARTS LIST
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
Parts may be ordered from authorized Windsor
dealers. When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside of
the front cover of this manual.
NOTE: For warranty information, contact your local
dealer or sales representative.
MODEL ______________________________________________
DATE OF PURCHASE __________________________________
SERIAL NUMBER _____________________________________
SALES REPRESENTATIVE # ___________________________
DEALER NAME _______________________________________
OPERATIONS GUIDE NUMBER __________________________
PUBLISHED __________________________________________
The model and serial number of your machine are
located as shown.
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards are identified that could
result in product or personal injury, or severe injury
resulting in death.
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
- Batteries
- Scrub Brushes
- Squeegee
- Service Schedule
- Machine Troubleshooting
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
- REF – column refers to the reference
number on the parts illustration.
- PART NO. – column lists the part number
for the part.
- PRV NO. – reference number.
- QTY – column lists the quantity of the
part used in that area of the machine.
- DESCRIPTION – column is a brief
description of the part.
- SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine. The
main illustration shows the most current
design of the machine. The boxed
illustrations show older designs.
- NOTES – column for information not noted
by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
1-1
86221970 17” SCRUBBER 08/20/09
IMPORTANT SAFETY INSTRUCTIONS
When using a battery powered appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components
and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
This machine is not suitable for picking up hazardous dust.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops
and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
Disconnect battery before cleaning or servicing.
Before the machine is discarded, the batteries must be removed and properly disposed of.
Make sure all warning and caution labels are legible and properly attached to the machine.
During operation, attention shall be paid to other persons, especially children.
Before use all covers and doors shall be put in the positions specified in the instructions.
When leaving unattended, secure against unintentional movement.
The machine shall only be operated by instructed and authorized persons.
Only chemicals recommended by the manufacturer shall be used.
This appliance has been designed for use with the brushes specified by the manufacturer.
The fitting of other brushes may affect its safety.
Do not use on surfaces having a gradient exceeding 2%.
SAVE THESE INSTRUCTIONS
86221970 17” SCRUBBER 01/03/07
2-1
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and
FOR SAFETY. The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or
property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist.
Locate all safety devices on the machine. Please take the necessary steps to train the machine
operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on
the machine. Use Windsor approved replacement parts.
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away.
Keep solution tank in raised position when charging. Keep sparks and flames away from the
batteries. Do not smoke around batteries.
Disconnect batteries before working on machine. Only qualified personnel should work inside
machine. Always wear eye protection and protective clothing when working on or near
batteries. Avoid skin contact with the acid contained in the batteries.
Never allow metal to lie across battery tops.
2-2
86221970 17” SCRUBBER 01/03/07
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become
illegible, promptly replace them.
FLAMMABLE
MATERIALS CAN
CAUSE EXPLOSION
OR FIRE.
DO NOT USE OR
PICK UP FLAMMABLE
MATERIAL.
SAFETY LABEL 86252540
PRV NO. 81505
BATTERY CAUTION 86252520
PRV NO. 80885
86221970 17” SCRUBBER 08/20/09
2-3
TECHNICAL SPECIFICATIONS
ITEM DIMENSION/CAPACITY
Rated Voltage 24 VDC
Rated Amperage 30 Amps
Batteries 2 x 12 Volt 105-130 AH
Scrub Brush Motor 0.75hp (0.56 kw)
Vacuum Motor 24 VDC 2 stage by pass
Mass (GVW) 319 lbs (144.7 kg)
Weight empty without batteries 142 lbs (64.4 kg)
Solution Control Gravity feed, fully variable
Solution tank capacity 8 Gal (30.3 ℓ)
Recovery tank capacity 10 Gal (37.9 ℓ)
Scrub brush diameter 17 in (430 mm)
Scrub brush pressure 33 lbs (15 kg)
Scrub brush speed 200 RPM
Wheels 2 x 6 in (15 cm) Thermoplastic non
marking
Casters 3.0 x 1.0 (75 mm)
Foundation Pressure 286 lbs/in² (1992.6 Kpa)
Coverage 6700 ft²/hr
Frame Construction Steel with epoxy powdercoat finish
Minimum aisle u-turn width 44 in (1110 mm)
Maximum rated climb and descent angle with empty
tanks
Maximum rated climb and descent angle with full tanks 2%
2%
3-1
86221970 17” SCRUBBER 01/03/07
TECHNICAL SPECIFICATIONS
ITEM MEASURE
Height 35 in (0.89 m)
Length 42 in (1.07 m)
Width without squeegee 20 in (0.51 m)
Width of squeegee 31 in (0.79 m)
Width of scrub path 17 in (0.43 m)
SPECIAL NOTES:
The A-weighted sound pressure level emitted by the
appliance was measured to be 74.1 dBA. This is a
space-averaged, broad-band measurement
determined according to IEC 704-I. This appliance
contains no possible source of impact noise.
Length
Height
The overall root-mean-squared acceleration at the
operator’s arms was measured to be less than 1.0
m/s². This is a tri-axial, broadband measurement
made during normal operation on a composite tile
floor.
Width
86221970 17” SCRUBBER 08/20/09
3-2
HOW THIS MACHINE WORKS
This Automatic Scrubber is a battery powered, hard
floor scrubber intended for commercial use. The
appliance applies a cleaning solution onto a hard
floor, scrubs the floor with a brush, and then
vacuums the soiled water back into the recovery
tank.
The machine's primary systems are the solution
system, scrub system and recovery system.
The function of the solution system is to store
cleaning solution and deliver it to the scrub system.
The solution system consists of the solution tank,
strainer, and valve. The solution tank stores cleaning
solution (water and detergent) until it is delivered to
the scrub system. The strainer protects the valve
from debris. The machine has a ball-type valve
which controls the amount of cleaning solution
delivered to the scrub system. The solenoid type
valve controls the delivery of cleaning solution to the
scrub system. The valve automatically prevents
solution flow unless the scrub brushes are turned
on. The solution control lever controls the amount of
cleaning solution delivered to the scrub system.
3-3
86221970 17” SCRUBBER 01/03/07
The function of the scrub system is to scrub the
floor. The scrub system consists of a rotary type
disk scrub brush, motor, and lift linkage. The brush
scrubs the floor and the motor drives the brush. The
brush lift lever raises and lowers motor and brush.
The function of the recovery system is to vacuum the
soiled water back into the recovery tank. The
recovery system consists of the squeegee, vacuum
motor, screen, and recovery tank. The squeegee
wipes the dirty solution off the floor as the machine
moves forward. The vacuum motor provides suction
to draw the dirty solution off the floor and into the
recovery tank. The screen protects the vacuum fan
from debris. The recovery tank stores the dirty
solution. The float ball in the tank activates when
the recovery tank is full.
1
2
4
9
12
1. Control Panel
2. Control Handle
3. Recovery Tank
4. Recovery Tank Drain Hose
5. Recovery Tank Domel
6. Scrub Brush/Pad
7. Solution Tank
8. Solution Tank Cover
COMPONENTS
5
3
7
10
13
6
14
9. Solution Tank Drain Hose
10. Solution Strainer
11. Solution Tank Support Lanyard
12. Squeegee
13. Vacuum Motor
14. Solenoid Valve
11
8
86221970 17” SCRUBBER 08/20/09
3-4
CONTROLS
5
1
6
4
2
9
8
7
3
1. Solution Control Lever
2. Brush Switch
3. Brush Lift Pedal
4. Vacuum Switch
5. Squeegee Lift Lever
3-5
86221970 17” SCRUBBER 01/07/11
6. Battery Charge Level Indicator
7. Hour Meter
8. Circuit Breaker
9. Brush Reverse Switch
1. SOLUTION CONTROL LEVER
Controls solution flow to scrub deck.
To increase flow push the knob forward to the
desired flow.
To decrease flow pull the knob back.
2. BRUSH SWITCH
Controls the scrub brush motor.
To turn scrub brush on, press the top of the
switch.
To turn scrub brush off, press the bottom of the
switch.
3. BRUSH LIFT PEDAL
Raises and lowers the brush.
To lower the brush, push down on pedal and
move to the left.
To raise the brush, lift the lever from its lowered
position.
4. VACUUM SWITCH
Controls the vacuum motor.
To start vacuum motor, press the top of the
switch.
To stop vacuum motor, press the bottom of the
switch.
5. SQUEEGEE LIFT LEVER
Raises and lowers the squeegee.
To lower the squeegee, lift and pull the lever to
the right and then lower.
To raise the squeegee, lift the lever and push it
to the left.
86221970 17” SCRUBBER 01/07/12
CONTROLS
6. BATTERY CHARGE LEVEL INDICATOR
Indicates the charge level of the batteries.
The meter display is divided into 10 vertical
bars. Bars illuminated on the top indicate full
charge. Bars flashing near the bottom indicate
the batteries should be recharged. Further
operation of the machine could damage the
machine or the batteries.
When the machine is left overnight with less
than a full charge, the display may initially
indicate a full charge. It will also indicate a full
charge if the batteries are disconnected, then
reconnected. After a few minutes of operation
the meter will give the correct charge level.
7. HOUR METER
Records the number of hours the machine’s
brush has been in operation. This information is
useful in determining when to service the
machine.
8. CIRCUIT BREAKERS
Circuit breakers interrupt the flow of power in the
event of an electrical overload. When a circuit
breaker is tripped, reset it by pressing the
exposed button. If a circuit breaker continues to
trip, the cause of the electrical overload should
be found and corrected.
25 Amp. Protects the scrub brush
motor.
25 Amp. Protects the vacuum
motor.
9. BRUSH REVERSE SWITCH
Reverses the scrub brush motor.
To activate, slide locking mechanism and press
the bottom of the switch.
3-6
MACHINE OPERATIONS
PRE-RUN MACHINE INSPECTION
Do a pre-run inspection to find possible problems
that could cause poor performance or lost time from
breakdown. Follow the same procedure each time to
avoid missing steps.
NOTE: See maintenance section for pre-run
machine inspection checklist items.
FILLING SOLUTION TANK
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine.
1. Turn the machine off.
2. Remove solution tank cover.
3. Fill the solution tank with clean water, leaving
enough room for the required amount of
cleaning solution. The solution tank capacity is
8 gallons (30.3 liters). The water must not be
hotter than 140° F (60°C) to prevent damage to
the tank.
4. Measure the chemical into the solution tank.
Liquid chemicals should be added to the solution
tank after filling with water. Dry chemicals
should be thoroughly mixed before being added
into the solution tank. Commercially available,
high alkaline floor cleaners are suitable for use
in the solution system.
NOTE: Read the chemical manufacturers
recommended proportion instructions.
5. Replace solution tank cover.
Flammable materials can cause an explosion or
fire. Do not use flammable materials in the
tanks.
NORMAL SCRUBBING
Plan the scrubbing pattern in advance. The longest
track is around the perimeter of the area to be
cleaned. For efficient operation, the runs should be
the longest possible without turning, stopping, or
raising and lowering scrub brush/squeegee.
NOTE: In order to achieve the best possible results,
the area that is to be cleaned should be swept
before scrubbing. Large debris, strings & wire mu st
be removed to prevent being caught in the brush or
squeegee.
3-7
86221970 17” SCRUBBER 01/03/07
MACHINE OPERATION
TO BEGIN SCRUBBING
When operating the machine around people, pay
close attention for unexpected movement. Use
extra caution around children.
Flammable liquids and/or reactive metals can
cause explosions or fire! Do not pick up.
1. Lower the squeegee.
2. Turn the vacuum on.
3. Lower the scrub brush to the floor.
4. Turn the scrub brush on.
5. Push machine forward to begin scrubbing.
NOTE: Shut machine off immediately if water or
foam is expelled from the machine.
6. Adjust the solution flow as necessary.
TO STOP SCRUBBING
1. Turn the scrub brush off.
2. Raise the scrub brush.
3. Raise the squeegee.
4. Turn the vacuum off.
DOUBLE SCRUB
For floors, which are heavily soiled or have thick
accumulations of floor finish the machine may not
clean sufficiently with one pass. In these cases it will
be necessary to double scrub. To double scrub,
make the first pass over the surface being cleaned
with the squeegee up, vacuum off, the solution on,
and brush down and on. This allows the solution to
stay in contact with the soil while loosening the
surface accumulation with the brush. Allow time for
the first application to stay in contact with the floor.
The length of time between the first and second
pass depends on the amount of accumulation and
the type of chemical being used. A second
scrubbing with the squeegee down, vacuum on and
again with solution and brush on will further loosen
the soil. The additional application of solution will
further assist the difficult cleaning job.
FOR SAFETY: When using machine, go slow on
inclines and slippery services.
EMPTYING AND CLEANING TANKS
1. Park the machine next to a drain. Drain hoses
are on the rear of the machine.
2. Turn the machine off.
SOLUTION TANK
1. Pull the small drain hose from the retainer.
Lower the hose in the direction of the drain.
2. Remove the solution tank cover.
3. Flush the solution tank out with clean water and
run several gallons of clean water through
systems. Do not use water hotter than 140°F
(60°C) to clean the tank, damage may occur.
NOTE: Never allow solution to remain in tank.
Damage to tank, seals and valves could occur.
4. Replace drain hose to retainer.
RECOVERY TANK
1. Unhook the large drain hose from the retainer.
Unscrew the drain cap from the end of the
recovery tank drain hose. Lower the hose in the
direction of the drain. Do not stand in front of the
end of the hose. Recovered solution will come
out with force.
2. Flush the recovery tank out with clean water. Do
not use water hotter than 140°F (60°C) to clean
the tank, damage may occur.
3. Clean off the float and check for free movement
of the float ball.
4. Replace the drain plug and secure the drain
hose in the retainer.
86221970 17” SCRUBBER 08/20/09
3-8
MAINTENANCE
BATTERIES (WET CELL BATTERIES ONLY)
The batteries provide the power to operate the
machine. The batteries require regular maintenance
to keep them operating at peak efficiency.
The machine batteries will hold their charge for long
periods of time, but they can only be charged a
certain number of times. To get the greatest life
from the batteries, charge them when their charge
level reaches 25% of a full charge. Use a
hydrometer to check the charge level.
Do not allow the batteries to remain in a discharged
condition for any length of time. Never expose a
discharged battery to temperatures below freezing.
Discharged batteries will freeze causing cracked
cases. Do not operate the machine if the batteries
are in poor condition or if they have a charge level
below 25% (specific gravity below 1.155).
Keep all metallic objects off the top of the batteries,
as they may cause a short circuit. Replace worn or
damaged cables and terminals.
Check the electrolyte level in each battery cell
before and after charging the batteries. Never add
acid to the batteries, use distilled water. Do not
allow water level to fall below the battery plates.
Portions of plates exposed to air will be destroyed.
Do not overfill. Keep plugs firmly in place at all
times.
When servicing machine, avoid contact with
battery acid.
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
Wear eye protection and protective clothing
when working with batteries.
Charge batteries in a well ventilated area.
BATTERY MAINTENANCE
1. When cleaning the batteries, use a solution of
baking soda and water. Do not allow the
cleaning fluid to enter the battery cells,
electrolyte will be neutralized.
2. Maintain the proper electrolyte level in each
battery cell. If a cell should accidentally
overflow, clean immediately.
3. Wipe off the top of the batteries at least once a
week.
4. Test battery condition with a hydrometer at least
once a week.
5. Ensure that all connections are tight and all
corrosion removed.
6. Every 4 to 6 months remove the batteries from
the machine and clean the battery cases and
battery compartment.
4-1
86221970 17” SCRUBBER 01/03/07
CHECKING BATTERY SPECIFIC GRAVITY
Use a hydrometer to check the battery specific
gravity.
CHECKING GRAVITY
A. Hydrometer
B. Battery
NOTE: Do not take readings immediately after
adding distilled water, if the water and acid are not
thoroughly mixed, the reading may not be accurate.
Check the hydrometer readings against this chart.
SPECIFIC GRAVITY
°
F (27°C)
@ 80
1.265 100% CHARGED
1.225 75% CHARGED
1.190 50% CHARGED
1.155 25% CHARGED
1.120 DISCHARGED
NOTE: If the readings are taken when the battery
electrolyte is any temperature other than 80°F
(27°C), the reading must be temperature corrected.
To find the corrected specific gravity reading when
the temperature of the battery electrolyte is other
than 80°F (27°): Add (+) to the specific gravity
reading 0.004 (4 points), for each 10°F (6°C) above
80° (27°C).
Subtract (-) from the specific reading 0.004 (4
points), for each 10°F (6°C) below 80°F (27°C)
Battery Check
BATTERY CONDITION
86221970 17” SCRUBBER 01/03/07
MAINTENANCE
TO CHARGE THE BATTERIES
When servicing machine, avoid contact with
battery acid.
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
Wear eye protection and protective clothing
when working with batteries.
Charge batteries in a well ventilated area. Leave
the solution tank open.
MACHINES EQUIPPED WITH ONBOARD
CHARGER
1. Fully open Recovery Tank/Battery Cover or prop
in partially open position using bracket
(included). This will provide additional venting of
batteries during charging cycle.
2. Connect charger’s AC power cord to AC mains.
The charger’s YELLOW “AC” LED will light.
NOTE: When charger is energized, all machine
function will shut down.
3. After several seconds, the charger’s green LED
will flash to indicate that charging is in process.
NOTE: If no lights are illuminated, or yellow LED
flashes, refer to the charger Product Manual
Troubleshooting section.
4. When charging is complete, both the yellow and
green LEDs will remain on. The charger is now
in standby mode.
5. Disconnect charger’s AC power cord.
6. Raise battery cover and check the battery
electrolyte level. It should be up to the indicator
ring. If necessary, add distilled water.
7. Lower the battery cover
NOTE: For additional information about battery
charger function, please see the charger Product
Manual.
4-2
MAINTENANCE-From Serial Number **
ON-BOARD CHARGER BATTERY SELECTION
! WARNING
Disconnect charger from wall outlet before
changing charge profiles. Failing to do so could
result in electrical shock.
DIPSWITCH: SW1
Charging Curve Table
DP1 DP2 CHARGING CURVE
ON OFF IUIa-ACD-for Wet batteries (default
setting)
ON ON IUIa-O AGM-for AGM or Gel batteries
(maintenance free)
Dipswitches are located behind the label on the front
of the charger. Peel the top right corner back to
reveal two sets of dipswitches.
Only dipswitch SW1 effects the charging curve.
Select the appropriate dip switch setting from the
Charging Curve Table. Do not change settings of
SW2. Changing settings of SW2 dipswitch could
result in charger failure.
Once the appropriate charger setting has been
selected, replace label. To verify charger settings,
observe charger immediately after startup. When
configured for lead-acid batteries, the red LED will
flash twice. If configured for gel/AGM batteries the
green LED will flash twice.
**CALL MANUFACTURER FOR SERIAL NUMBER
4-3
86221970 17” SCRUBBER 11/25/09
MACHINES WITHOUT ONBOARD CHARGER
Use a 24 volt, 12 amp maximum output, DC charger
which will automatically shut off when the batteries
are fully charged to charge the two battery pack.
1. Stop the machine in a clean, well ventilated area
next to the charger.
2. Turn the machine off.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine.
3. Drain recovery tank and raise the recovery tank.
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
4. Check the electrolyte level in each battery cell.
Before charging, add just enough distilled water
to cover the plates. After charging is complete,
add just enough distilled water to bring up the
level to the indicator ring. If the water level is
too high before charging, normal expansion rate
of the electrolyte may cause an overflow.
Resulting in a loss of battery acid balance and
damage the machine.
5. Replace the battery caps, and leave them in
place while charging.
6. Unplug the battery connector from the machine.
FOR SAFETY: When charging, connect the
charger to the batteries before connecting the
charger to the AC wall outlet. Never connect the
charger to the AC wall outlet first. Hazardous
sparks may result.
7. Plug the charger connector into the battery
connector. Connect the charger AC plug to a
wall outlet. The charger gauge should indicate
that the batteries are charging.
8. When the batteries are fully charged, disconnect
the charger from the AC wall outlet, then
disconnect the charger from the batteries.
9. Connect the batteries to the machine connector.
10. Check the electrolyte level. It should be up to
the indicator ring. If necessary, add distilled
water.
11. Lower the recovery tank.
86221970 17” SCRUBBER 01/03/07
MAINTENANCE
CHANGING BATTERIES
Stop the machine in a clean area next to the
charger. Turn off machine.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn off machine.
1. Drain recovery tank and raise the recovery tank.
2. Disconnect battery pack from machine.
3. Disconnect squeegee lift cable and vacuum
hose.
4. Prepare a suitable site to place the batteries.
5. Pull battery tray with batteries out of rear of
machine.
Batteries are a potential environmental hazard.
Consult your battery supplier for safe disposal
methods.
+ red
- blk
- blk
+ red
4-4
MAINTENANCE
SCRUB BRUSHES
NOTE: All original equipment brushes are equipped
with “Perform Alert©”. This feature will tell the
operator when it is time to replace the scrub brush.
“Perform Alert©” brushes have pre-trimmed bright
yellow tufts to indicate the length of a worn out
brush. When the tufts in the scrub brush wear to a
length equal to the yellow tufts, the scrub brush
should be replaced.
There are three different types of brushes available
to cover applications from cleaning heavily soiled
floors to polishing. A pad driver is also available to
take advantage of the many cleaning pads on the
market and further add to the flexibility of the Saber
Compact. Please refer to the following to assist in
selecting the proper brush or pad for the work at
hand.
UNCOATED FLOORS
Mild Grit is a less aggressive silicone carbide grit
suitable for cleaning medium soil conditions.
Advantages are faster ground speed than nylon
bristles on light solid applications.
Polypropylene is a general-purpose scrub brush
with stiff bristles. Polypropylene works well for
maintaining concrete, wood and tile floors.
4-5
86221970 17” SCRUBBER 01/03/07
FINISHED FLOORS
Nylon bristles are used in a variety of applications
on coated or uncoated surfaces.
White Pads (Polishing) are used for dry polishing to
achieve a high-gloss appearance, or surface
washing on highly polished or burnished floors.
Red Pads (Buffing) are used for light-duty
scrubbing. When used with a mild detergent they
will provide surface cleaning without removing the
finish.
Blue Pads (Scrubbing) are used for heavy-duty
scrubbing and light stripping. The blue pads remove
less finish than brown stripping pads, yet will remove
black marks, stains and dirt.
Brown Pads (Stripping) are used for easy and
complete removal of old floor waxes/finishes. They
will quickly remove ground in dirt, black heel marks,
and spills. When used with the proper stripper, this
pad leaves the floor clean and ready for finishing.
The scrub brush should be checked before each
days work for wire, string, wear and damage. The
scrub brush should be replaced if brush bristles are
missing or if yellow Perform Alert © indicates
minimum brush length.
MAINTENANCE
REPLACING OR REMOVING SCRUB BRUSHES
1. Turn the machine off.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn OFF
machine.
2. Raise the scrub deck up by pushing down on the
pedal.
3. Locate the brush reverse switch on the rear of
the panel. Slide locking mechanism and press to
activate the motor then release to disconnect
brush driver.
4. Tilt and pull machine back to expose brush
driver.
INSTALLING SCRUB BRUSHES
1. Turn the machine off.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn OFF
machine.
2. Tilt and push machine over brush driver. The
brush centering bracket will position the brush
driver.
3. Lower the scrub deck by pushing the pedal
down and to the left.
4. Locate the brush switch and turn on.
SQUEEGEE BLADES
The front squeegee blade allows solution to pass
through channels in the blade into the squeegee
assembly while maintaining vacuum to provide lift.
The rear blade wipes the floor to a near dry
condition. It is important the rear blade be in good
condition to properly do its job.
Check both the front and rear squeegee blades for
damage and wear each day in the pre-run check.
Change the front blade if it is torn or has an uneven
edge. Change the rear blade if it is less than 1/2 the
original thickness.
TO REMOVE SQUEEGEE ASSEMBLY
1. With the squeegee in the up position, turn the
machine power off.
2. Loosen both squeegee knobs and pull squeegee
assembly rearward from the lifting carrier.
3. Inspect or repair as necessary and reinstall.
TO REPLACE SQUEEGEE BLADES
1. With the squeegee in the up position, turn the
machine power off.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine.
2. Remove the squeegee assembly from the
machine. Remove all screws and remove blade
retainer strap and remove squeegee blade.
3. Replace squeegee blades as required.
4. Install squeegee blade.
5. Install squeegee retainer strap.
6. Install all screws starting from center and
working to ends.
86221970 17” SCRUBBER 01/07/12
4-6
MAINTENANCE
4
-
SERVICE SCHEDULE
MAINTENANCE DAILY WEEKLY MONTHLY ANNUALLY
Before
starting
the work
period
End of work
period
before
storing
Check battery acid level *
Check vac hose connections *
Clean the squeegee blades *
Inspect brush or pad for debris:
wire string, wear
Inspect float ball screen *
Drain & rinse tanks *
Raise squeegee assembly *
Raise scrub deck assembly *
Charge the batteries. *
Remove the pad driver/brush *
Check the brush/pad for damage
and/or wear
Clean squeegee blades *
Clean recovery tank shut off &
screen
Check battery cells w/ hydrometer *
Check solution strainer *
Check pivot points and casters for
proper lubrication
Inspect tank and hoses *
Clean tops of batteries *
Check battery cable clamps *
Use a vacuum to remove lint from
the motor windings
Grease casters *
Inspect all motors for carbon
motor brush wear
*
*
*
*
*
*
7
86221970 17” SCRUBBER 01/03/07
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Poor or no water pick-up
Debris caught on squeegee Remove debris
Worn squeegee blades Replace squeegee blades
Vacuum hose clogged Clear obstruction from hose
Vacuum hose disconnected
from squeegee or recovery
tank
Vacuum hose damaged Replace vacuum hose
Reconnect vacuum hose
Vacuum motor does not run, or runs
slowly
Poor scrubbing performance
Vacuum motor inlet screen
dirty
Recovery tank not sealed Check vacuum motor
Foam filling recovery tank Empty recovery tank
Recovery tank full Drain recovery tank
Circuit breaker tripped Reset circuit breaker
Loose connection Check motor wires and
Faulty vacuum contractor Replace contactor
Worn vacuum motor brushes Replace brushes, check
Debris caught in scrub brush Remove debris
Worn brush or pad Replace brush or pad
Improper detergent, brush or
pad used
Low scrub brush down
pressure
Low battery charge Charge batteries
Clean inlet screen
position. Replace damaged
seal.
Use less or different
detergent
Use defoamer
connections
commutator
Contact equipment or
application specialist
Increase brush pressure
Brush motor does not run, or runs
slowly
86221970 17” SCRUBBER 01/03/07
Circuit breaker tripped Reset circuit breaker
Loose connection Check motor wires and
connection
Faulty brush motor contactor Replace contactor
Worn brush motor brushes Replace brushes, check
commutator
4-8
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Little or no solution flow to the floor
Solution tank empty Fill solution tank
Solution flow turned off or set
too low
Solution strainer plugged Clean solution strainer
Solution hoses obstructed Clear obstruction from hose
Turn on or increase flow
setting
No power to machine
Little or no propel
Solution solenoid valve
obstructed or stuck
Battery disconnected Check all battery cable
Emergency shut-off activated Reset
Battery connections corroded Clean connections
Faulty main contactor Replace contactor
Faulty power switch Replace switch
Low battery charge Charge batteries
Machine turned on with
directional control button(s)
not in neutral
Controller overheated Allow cool down period
Loose connection Check motor wires and
Clean or replace
connections
Allow control button to return
to neutral. Restart
connection
86221970 17” SCRUBBER 01/03/07
4-9
17” SCRUBBER
PARTS LIST
86221970 17” SCRUBBER 01/03/07
DECAL
3A
3B
1A
1B
2A
2B
5
4
5-1
86221970 17” SCRUBBER 04/17/09
REF PART NO. PRV NO. QTY DESCRIPTION
1A 86243040 500301 1 LABEL, MAIN (RIGHT)
1B 86244000 500789 1 LABEL, MAIN (RIGHT) HCC172
2A 86243050 500302 1 LABEL, MAIN (LEFT)
2B 86244010 500790 1 LABEL, MAIN (LEFT) HCC172
3A 86004970 50990 1 LABEL, LOGO DOMED
3B 86244020 500794 1 LABEL, LOGO DOMED HCC172
4 86220670 501027 1 LABEL, CIRCUIT BREAKER
5 86220660 501026 1 LABEL, PANEL 17 IN
SERIAL NO.
FROM
NOTES:
SCC172, QSCC172,
SCHC172, QSC172
SCC172, QSCC172,
SCHC172, QSC172
SCC172, QSCC172,
SCHC172, QSC172
DECAL
86221970 17” SCRUBBER 04/17/09
5-2
CONTROL PANEL- W/CHARGER
5-3
86221970 17” SCRUBBER 01/07/12
CONTROL PANEL – W/CHARGER
REF PART NO. PRV NO. QTY DESCRIPTION
1 86348660 - 1 SWITCH, 2 POSN, BRUSH
2 86007140 72130 1 SWITCH, SPST 2-POSITION ROCKER
3 86348650 - 1 SWITCH, 2 POSN, LOCKING
4 86276820 70740 6 SCR, 10-32 X 1/2 PTHMS BLK NP
5 86218800 41540 1 HANGER, CHARGER CORD 172
6 86215420 140888 2 BOOT, M12 CIRCUIT BREAKER
7 86215860 140913 1 BRKT, HOSE HOOK
8 86231240 140429 1 BUSHING, .75 ID X .25 H
9 86255910 73659 2 STANDOFF, 1/4-20 X 1.0 HEX INS
10 86006850 70393 2 SET SCR, 1/4-20 X 1.25 L
11 86222310 57311 3 NUT, 1/4-20 UNC
12 86005640 57030 4 NUT, 10-32 HEX NYLOCK
13 86215680 140931 2 BREAKER, 25A, 250VAC 50VDC
14 86005680 57047 2 NUT, 1/4-20 HEX NYLOCK
15 86274290 70162 2 SCR, 10-32 X 3/8 PPHMS SS
16 86222490 61480 1 PANEL, SCRUBBER 17 IN
17 86010660 87025 5 WASHER, 1/4 LOCK EXT STAR SS
18 86224880 730365 4 STANDOFF, HEX BRASS 6-32 THRD
19 86246970 54192 1 METER, 24V BATTERY W/OUTPUT
20 86251420 67610 1 RELAY, 24VDC 40A /BRKT
21 86218070 35358 2 GASKET, ELECTRIC COVER SIDE
22 86218080 35359 1 GASKET, ELECTRICAL COVER
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 01/07/12
5-4
CONTROL PANEL- SCHC172 W/CHARGER
1
2
16
22
11
18
4
19
3
21
4
20
17
18
4
5
4
6
12
13
5-5
86221970 17” SCRUBBER 05/18/11
15
12
23
17
11
17
10
14
7
8
9
CONTROL PANEL SCHC172 W/CHARGER
REF PART NO. PRV NO. QTY DESCRIPTION
1 86348660 - 1 SWITCH, 2 POSN, BRUSH
2 86007140 72130 1 SWITCH, SPST 2-POSITION ROCKER
3 86257090 72181 1 SWITCH, DPST 2-POSITION ROCKER
4 86276820 70740 6 SCR, 10-32 X 1/2 PPHMS BLK NP
5 86218800 41540 1 HANGER, CHARGER CORD 172
6 86215420 140888 2 BOOT, M12 CIRCUIT BREAKER
7 86215860 140913 1 BRKT, HOSE HOOK
8 86231240 140429 1 BUSHING, .75 ID X .25 H
9 86255910 73659 2 STANDOFF, 1/4-20 X 1.0 HEX INS
10 86006850 70393 2 SET SCR, 1/4-20 X 1.25 L
11 86222310 57311 4 NUT, 1/4-20 HEX UNC BLACK C
12 86005640 57030 4 NUT, 10-32 HEX NYLOCK SS
13 86215680 140931 2 BREAKER, 25A, 250VAC, 50VDC
14 86274290 70162 2 SCR, 10-32 X 3/8 PPHMS SS
15 86005680 57047 2 NUT, 1/4-20 HEX NYLOCK
16 86222490 61480 1 PANEL, SCRUBBER
17 86010660 87025 5 WASHER, 1/4 LOCK EXT STAR SS
18 86224880 730365 4 STANDOFF, HEX BRASS 6-32 THRD
19 86246970 54192 1 METER, 24V BATTERY W/OUTPUT
20 86251420 67610 2 RELAY, 24VDC 40A W/BRKT
21 86218070 35358 2 GASKET, ELECTRICAL COVER SIDE
22 86218080 35359 1 GASKET, ELECTRICAL COVER
23 86251400 67495 1 RELAY, BATTERY METER OUTPUT
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 01/04/11
5-6
CONTROL PANEL – QSC172
1
2
5
19
18
20
18
16
3
4
4
4
14
6
5-7
12
13
15
12
17
11
10
17
86221970 17” SCRUBBER 01/07/12
14
7
8
9
CONTROL PANEL-QSC172
REF PART NO. PRV NO. QTY DESCRIPTION
1 86348660 - 1 SWITCH, 2 POSN, BRUSH
2 86007140 72130 1 SWITCH, SPST 2-POSITION ROCKER
3 86348650 - 1 SWITCH, 2 POSN, LOCKING
4 86276820 70740 4 SCR, 10-32 X 1/2 PPHMS BLK NP
5 86218080 35359 1 GASKET, ELECTRICAL COVER
6 86215420 140888 2 BOOT, M12 CIRCUIT BREAKER
7 86215860 140913 2 BRKT, HOSE HOOK
8 86231240 140429 1 BUSHING, .75 ID X .25 H
9 86255910 73659 2 STANDOFF, 1/4-20 X 1.0 HEX INS
10 86006850 70393 2 SET SCR, 1/4-20 X 1.25 L
11 86222310 57311 2 NUT, 1/4-20 HEX UNC BLACK C
12 86005640 57030 4 NUT, 10-32 HEX NYLOCK SS
13 86215680 140931 2 BREAKER, 25A, 250VAC, 50VDC
14 86274290 70162 2 SCR, 10-32 X 3/8 PPHMS SS
15 86005680 57047 2 NUT, 1/4-20 HEX NYLOCK
16 86222490 61480 1 PANEL, SCRUBBER
17 86010660 87025 4 WASHER, 1/4 LOCK EXT STAR SS
18 86224880 730365 4 STANDOFF, HEX BRASS 6-32 THRD
19 86246970 54192 1 METER, 24V BATTERY W/OUTPUT
20 86218070 35358 2 GASKET, ELECTRICAL COVER SIDE
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 01/07/12
5-8
HOUR METER
2
5
1
4
3
5-9
86221970 17” SCRUBBER 04/17/09
REF PART NO. PRV NO. QTY DESCRIPTION
1 86267420 880283 1 WIRE, 3.5 BLK/18 79011 X 76040
2 86260500 880349 1 WIRE ASM, HOUR METER
3 86005530 54154 1 METER, 12-48 VDC LED HOUR
4 86261240 29243 1 DIODE ASM, 76031 X 76031
5 86261340 67457 1 RESISTOR ASM, 2.7K OHM 1 WATT
SERIAL NO.
FROM
HOUR METER
NOTES:
86221970 17” SCRUBBER 04/17/09
5-10
HANDLE
4
3
5
2
1
6
7
5-11
86221970 17” SCRUBBER 08/20/09
HANDLE
REF PART NO. PRV NO. QTY DESCRIPTION
1 86218620 38349 1 HANDLE, 17 IN SCRUBBER
2 86004880 48079 2 KNOB, 2.25 OD X 5/16-18 X 2.19 STUD
3 86221880 51416 2 LOCK, HANDLE, MALE
4 86221890 51417 2 LOCK, HANDLE, FEMALE
5 86069430 140439 2 BRKT, HANDLE MOUNT SUPPORT
6 86216530 270143 2 CAP, HANDLE
7 86277230 70815 2 SCR, 5/16-18 X 2.25 BSHCS SS SCHC172 ONLY
SERIAL NO.
FROM
ALL EXCEPT
NOTES:
SCHC172
86221970 17” SCRUBBER 04/17/09
5-12
RECOVERY TANK
1
10
17
11
19
18
20
10
12
10
13
16
4
10
2
3
14
5A
5B
5-13
15
9
8
7
6
SCHC172
86221970 17” SCRUBBER 07/27/09
RECOVERY TANK
REF PART NO. PRV NO. QTY DESCRIPTION
1 86003340 28062 1 DOME, 13 X 11
2 86006600 70114 4 SCR, #10 X 3/4 PPHST TYPE B SS
3 86222860 620100 1 PLATE, VAC INLET COVER
4 86003680 34380 1 FLOAT SHUT-OFF
5A 86225290 75476 1 TANK, RECOVERY DK GRY
5B 86225280 75475 1 TANK, RECOVERY, TEAL SCHC172
6 86003010 27759 1 CUFF, HOSE, 1.5 IN BLACK
7 86246070 51352 1 LANYARD, DRAIN HOSE QSC172 ONLY
8 86004290 39491 1 HOSE, 1.5 BLK VAC X 45”
9 86004190 39337 1 HOSE, 1.5 BLK VAC X 24”
10 86002390 20063 4 CLAMP, 1.75” WORM GEAR X .312
11 86328980 - 1 DRAIN CAP ASSEMBLY
12 86240130 39560 1 HOSE, P-TRAP 45 DEG
13 86004010 35274 1 GASKET, DOME EDGE
14 86218100 35361 1 GASKET, VAC INLET
15 86216790 20109 1 CLIP, VAC HOSE COIL
16 86279880 27425 1 CORD, 1/8” X 16”
17 86215060 140967 1 BAFFLE, AIR INTAKE
18 86223820 70926 2 SCR, 10-32 X .748 PPHMS SS C
19 86222280 57307 2 NUT, 10-32 HEX NYLOCK SS C
20 86010650 87018 2 WASHER, #10 X 9/16 OD
SERIAL NO.
FROM
ALL EXCEPT
NOTES:
SCHC172
86221970 17” SCRUBBER 07/27/09
5-14
SCRUB BRUSH/PAD DRIVER
5-15
86221970 17” SCRUBBER 04/17/09
SCRUB BRUSH/PAD DRIVER
REF PART NO. PRV NO. QTY DESCRIPTION
1 86000680 02464 1 PAD DRIVER, 17” BA
2 86005070 51284 1 LOCK, PAD CENTER SNAP, TWO STEP
3 86276580 70694 3 SCR, 8-32 X 3/4 PTHMS SS
4A 86000650 02461 - BRUSH, 17” POLYPRO BA
4B 86000660 02462 - BRUSH, NYLON BA
4C 86000670 02463 - BRUSH, 17” GRIT BA
4D 86000700 02509 - BRUSH, NYLON UNTRIMMED
5 86340340 - 3 SCR, M6 X 40MM PFHMS SS
86004990
6
51076 3 LUG, BRUSH MOUNTING
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/01/10
5-16
SCRUB MOTOR/LIFT
1
2A
3A
3B
32
5
2B
7
29
14
15
30
28
31
SCHC172
7
6
8
9
10
11
12
13
18
33
16
7
27
26
5-17
25
11
23
24
17
34
19
20
21
22
12
86221970 17” SCRUBBER 07/17/09
SCRUB MOTOR/LIFT
REF PART NO. PRV NO. QTY DESCRIPTION
1 86005320 53630 1 MOTOR ASM, 24VDC 200 RPM GEAR
2A 86010610 84203 1 VALVE, 24VDC SOL 3/8 HOSE CIM
2B 86010540 84141 1 VALVE, 24VDC SOL 1/2 HOSEBARB SCHC172
3A 86282080 39567 1 HOSE 3/8 NYLOBRD X 3.5
3B 82681470 39386 1 HOSE, 1/2 VINYL X 4 SCHC172
4 OPEN
5 86215990 149987 1 BRKT, SOLENOID VALVE 172
6 86070650 140711 1 BRKT, MTR MNT STIFFENER
7 86270830 57023 9 NUT, 5/16-18 HEX NYLOCK SS
8 86259400 87205 4 WASHER, THRUST .51 ID X 1 OD BRO
9 86259410 87206 4 WASHER, THRUST .51 ID X 1 OD X .063
10 86231250 140430 4 BUSHING, .5 OD X .31 ID X .4 L SS
11 86010670 87029 8 WASHER, 5-16 SS FLAT
12 86007020 70673 5 SCR, 5/16 –18 X 1.25 HHCS SS
13 86072600 14431 1 BRKT, MOTOR TRACK
14 86278910 87003 7 WASHER, 3/8 X 7/8 OD SS
15 86006740 70266 4 SCR, 3/8-16 X 1” HHCS GR5
16 86073580 620043 1 BRKT, DECK STIFFENER
17 86276800 70734 1 SCR, 10-32 X 3/8 HHMS SS
18 86173350 87515 2 WASHER, M5, FLAT, ISO7089, SS
19 86224610 730359 1 SPRING, BRUSH CLIP
20 86003430 29237 1 DRIVER, BRUSH ASSIST
21 86279630 87212 1 WASHER, .344 ID X 1.13 OD X .09 T PLT
22 86279130 87083 1 WASHER, 5/16 SPLIT LOCK PLTD
23 86006560 70083 4 SCR, 5/16-18 X 1HHCS SS
24 86225820 87508 1 WASHER, .78 ID X 1.63 OD X .197 PLT
25 86007690 73240 1 SPRING, EXT .50 OD X 2.25 L X .063 W
26 86272340 66191 1 PIN, CLEVIS 3/16 X .50 PLTD
27 86221740 51414 1 LEVER, MOTOR LIFT
28 86278360 70731 1 SHOULDER BOLT, 3/8 OD X 1/2L SS
29 86072610 14432 1 BRKT, MOTOR TRACK
30 86072590 14430 1 BRKT, MOTOR MOUNT
31 86004810 48040 1 KEY, 1/4 SQ X 1.00
32 86276730 70719 2 SCR, M4 X 8MM LG PPHMS
33 86172950 70909 2 SCR, M5X12, SHCS, ISO4762, SS
34 86279470 87165 1 WASHER, #10 SPLIT LOCK PLTD
SERIAL NO.
FROM
ALL
ALL
NOTES:
EXCEPT
SCHC172
EXCEPT
SCHC172
86221970 17” SCRUBBER 07/17/09
5-18
SOLUTION TANK
4
3
2
26
13
28
27
16
33
1
34
35
7
6
5
8
30
31
29
25
5-19
32A
32B
23
22
24
86221970 17” SCRUBBER 08/20/09
19A
19B
18A
18B
10
21
20
9
10
11
12
13
14
15
17
16
SOLUTION TANK
REF PART NO. PRV NO. QTY DESCRIPTION
1 86239620 41385 1 HINGE, 17 IN SCRUBBER
2 86010660 87025 6 WASHER, 1/4 LOCK EXT STAR SS
3 86276700 70716 4 SCR, 1/4-20 X 1/2 PTHMS
4 86003210 27906 1 CABLE, TANK LANYARD
5 86278260 70298 2 SHOULDER BOLT, 5/16 X 3/8 SSHLD
6 86215820 140886 1 BRKT, TANK SUPPORT
7 86234790 27827 1 COVER, SOLUTION TANK
8 86279880 27425 1 CORD, 1/8” X 16”
9 86282110 39571 1 HOSE, 1/2” ID WIRE BOUND X 5.5”
10 86197940 40027 2 HOSEBARB, 3/8 MPT X 1/2 90 D
11 86069410 140406 1 BRKT, VALVE MOUNT
12 86224430 730375 1 SPACER, .259 ID X 3/8 OD X .37
13 86221750 51418 1 LEVER, SOLUTION CABLE
14 86222280 57307 1 NUT, 10-32 HEX NYLOCK SS
15 86328920 - 1 SCR, HHSS, M4X5.3 SS WAS 70403
16 86006980 70591 3 SCR, 10-32 X 1/2 HHCS SS
17 86010650 87018 1 WASHER, #10 X 9/16 OD
18A 86282090 39569 1 HOSE, 3/8” ID X .05 W CLR X 12” NYLOBRD
18B 86281640 39471 1 HOSE, 1/2” VINYL X 15” NYLOBRD SCHC172
19A 86240430 40083 1 HOSEBARB, 3/8 MPT X 3/8 NYLON
19B 86001590 40049 1 HOSEBARB, 3/8 MPT X 1/2 NYLON SCHC172
20 86248020 81380 1 NUT, SEALED BULKHEAD
21 86225680 84201 1 VALVE, 3/8 FPT BALL
22 86233110 20018 1 CLAMP, 1.0 WORM GEAR
23 86219160 40108 1 HOSEBARB, 1/2 MPT X 3/4 90D
24 86282100 39570 1 HOSE, 3/4 ID X .12 W CL X 36 L
25 86005640 57030 2 NUT, 10-32 HEX NYLOCK
26 86276820 70740 6 SCR, 10-32 X 1/2 PPHMS BLK
27 86242100 48083 1 KNOB, SOLUTION LEVER
28 86240810 830156 1 HOSEBARB, 1/2 MPT X 3/4
29 86007350 730040 1 STRAINER, 3/8” NPT 20 MESH
30 86198450 20005 1 CLAMP, 5/16 NYLON
31 86221020 501102 1 LABEL, VENT/DRAIN
32A 86322090 - 1 TANK, SOLN SC17 DK BLU
32B
86327580
33 86274290 70162 1 SCR, 10-32 X 3/8 PPHMS SS
34 86279190 87095 1 WASHER, #10 FLAT PLTD
35 86279790 87489 1 WASHER, #10 X 9/16 OD
** CALL MANUFACTURER FOR SERIAL NUMBER
- 1 TANK, SOLN SC17 DK GRY
SERIAL NO.
FROM
ALL
ALL
**
**
NOTES:
EXCEPT
SCHC172
EXCEPT
SCHC172
ALL
EXCEPT
HCC172
WAS
86032460
HCC172
WAS
86032470
86221970 17” SCRUBBER 08/07/09
5-20
SQUEEGEE
30
29
2
25
24
26
14
21
23
21
22
20
28
27
11
13
6
7
1
8A
8B
8C
8D
3
4
5
9
10
12
10
14
17
15
5-21
86221970 17” SCRUBBER 09/17/10
16
18A
18B
19
REF PART NO. PRV NO. QTY
86223740
1
86225450
2
86332620
3
86219690
4
86215800
5
86219730
6
86224950
7
86215360
8A
86007370
8B
86007260
8C
86007610
8D
86224240
9
86225790
10
86011020
11
86001350
12
86334640
13
86222300
14
86332670
15
86223750
16
86223760
17
86215350
18A
86007360
18B
86087870
19
86010880
20
86225780
21
86008660
22
86279650
23
86215810
24
86222590
25
86222290
26
86332630
27
86332650
28
86276610
29
30 86224870 730384 1 SQUEEGEE, 17 INCH CAST
70872 2 SCR, 1/4-20 X .59 PPHMS SS C
78936 1 TUBE, 17 IN. TRANSITION
- 1 GASKET, SUCTION, SQG TRANS
48080 2 KNOB, 1.5 OD X 5/16-18
140883 1 BRKT, SQUEEGEE MOUNT
48112 10 KNOB, SQUEEGEE RETAINER
730366 1 STRAP, SQUEEGEE BLADE, REAR
730372 1 BLADE, SQUEEGEE, REAR
730058 1 BLADE, RED REAR SOFT DURO 40
730003 - BLADE, BLU, RIB FRT/REAR URETHANE
730227 - BLADE, RED, REAR MEDIUM DURO 60
70870 2 SHOULDE R BLT, .305 OD X 1.77 SS C
87504 4 WASHE R, 5/16 X .63 SS
89202 2 WHEEL, 3” DIA CUSHION RUBBER
140390 2 BUSHING, SPANNER .435 X 1.10
- 1 PLATE, TOP, CAST SQG
57309 6 NUT, 5/16-1 8 JAM SS
- 2 SQUEEGEE, END INSERT 17 IN
70873 2 SCR, 5/16-18 X 1.77 BHSMS SS
70874 2 SCR, 5/16-18 X 2.17 BHSMS SS
730371 1 BLADE, SQUEEGEE FRONT
730057 1 BLADE, RED FRONT 5 SLOT DURO 40
730002 1 STRAP, FRONT AND REAR STANDARD
89058 2 WHEEL, 1.5 OD X .31 ID X .75 W GRY
87503 4 WASHE R, 5-16 X .55 SS
80605 2 COTTER, 5/16” RING
87222 2 WASHER, SEAL 5/16 X 3/4 OD SS
140884 2 BRKT, SQG WHEEL
66876 2 PIN, CLEVIS 5/16 1.469 C
57308 2 NUT, 5/16-1 8 HEX NYLOCK SS
- 1 GASKET, LOWER, 17" SQG
- 1 SQUEEGEE, CENTER INSERT, 17IN
70697 2 SCR, 1/4-20 X 1.25 PPHMS SS
DESCRIPTION
* COMPLETE ASSEMBLY, ITEM 5 NOT INCLUDED
SQUEEGEE
SERIAL NO.
FROM
NOTES:
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
*
86221970 17” SCRUBBER 09/17/10
5-22
SQUEEGEE LIFT
5-23
86221970 17” SCRUBBER 04/17/09
SQUEEGEE LIFT
REF PART NO. PRV NO. QTY DESCRIPTION
1 86005680 57047 1 NUT, 1/4-20 HEX NYLOCK
2 86270830 57023 2 NUT, 5/16-18 HEX NYLOCK SS
3 86249050 82058 1 PIN, CLEVIS 3/8 X 3.50 PLTD
4 86008670 80606 1 COTTER, 3/8” RING
5 86007020 70673 2 SCR, 5/16-18 X 1.25 HHCS SS
6 86228840 09124 2 BEARING, FLANGED .314 ID X .502 OD
7 86259400 87205 2 WASHER, THRUST .51 ID X 10 D BRO
8 86006320 66338 1 PLATE, SQUEEGEE LIFT
9 86259410 87206 2 WASHER, THRUST .51 ID X 1 OD X .063
10 86239670 41386 1 HOOK, SAFTEY CLIP
11 86003220 27921 1 CABLE, SQUEEGEE LIFT 21.4 L
12 86246460 51351 1 LEVER, SQUEEGEE LIFT
13 86005640 57030 1 NUT, 10-32 HEX NYLOCK
14 86136860 70356 1 SHOULDER BOLT, 5/16 OD X 2.0 L
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-24
VACUUM
5-25
86221970 17” SCRUBBER 04/17/09
VACUUM
REF PART NO. PRV NO. QTY DESCRIPTION
1 86003760 35166 1 GASKET, VAC MTR
2A 86005440 53797 1 VAC MOTOR, 24VDC 2ST TD
2B 86135310 140686 - BRUSH SET, 24/36V VAC, WINDSOR SERVICE ONLY
3 86217750 31374 1 ELBOW, VAC MUFFLER 90 DEG
4 86072620 14433 3 BRKT, VAC MOTOR MNT
5 86216000 149988 1 BRKT, MUFFLER 172
6 86222220 54204 1 MUFFLER, VACUUM FOAM 172
7 86215370 140896 1 BLANKET, SOUND REDUCTION
8 86273750 70011 3 SCR, 1/4-20 X 5/8 HHCS SS NP
9 86010630 87013 3 WASHER, 1/4 ID X 5/8 OD SS
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-26
WHEEL & FRAME
5-27
86221970 17” SCRUBBER 04/17/09
WHEEL & FRAME
REF PART NO. PRV NO. QTY DESCRIPTION
1 86003700 34421 1 FRAME, 17 IN SCRUBBER
2 86223770 70875 2 SCR, 5/16-18 X 1.89 HHCS SS C
3 86011020 89202 2 WHEEL, 3” DIA CUSHION RUBBER
4 86216400 140903 2 BUSHING, SPANNER .435 X 1.19
5 86078910 620029 2 PLATE, CASTER MOUNT
6 86270830 57023 4 NUT, 5/16-18 HEX NYLOCK SS
7 86070600 140692 2 BRKT, SPLASH GUARD
8 86271770 57252 8 NUT, 10-24 HEX NYLOCK SS
9 86343450 - 2 SWIVEL CASTER, 3.7 “ *(1)
10 86279130 87083 8 WASHER, 5/16 SPLIT LOCK PLTD
11 86006930 70514 8 SCREW 5/16-18 X 1.00 BSHCS SS *(1)
12 86276770 70726 8 SCR, 10-24 X 5/8 HHMS SS
13 86010650 87018 8 WASHER, #10 X 9/16 OD
14 86253870 730043 2 SKIRT, CASTER SHIELD
15 86082060 62893 1 PLATE, BRUSH CENTER
16 86273740 70010 3 SCR, 1/4-20 X 1.2 HHCS SS
17 86010810 87191 3 WASHER, 1/4” ID X 1.0 OD FLAT SS
18 86259870 89223 2 WHEEL, 1.25 TREAD X 6 DIA
19 86276750 70722 2 SCR, 5/16-18 X 2.5 FHSC SS
20 OPEN - - -
21 OPEN - - -
22 86087880 730035 2 STRAP, SKIRT SIDE
23 86007320 730029 1 SKIRT, 17” SCRUBBER
24 86276620 70699 8 SCR, 10-24 X 1/2 PTHMS SS
*SEE SERIAL NUMBER PAGE.
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 06/22/10
5-28
ONBOARD CHARGER
5-29
86221970 17” SCRUBBER 10/12/09
REF PART NO.
1 86216670 270051 1
2 86215790 140880 1 BRKT, 17 IN CHARGER
3 86215780 140879 1 BRKT, TOP 17 IN CHARGER
4 86218060 35357 2 GASKET, 4.25 L X .55 W X .38
5 86220720 501033 1 LABEL, CHARGER 1608FS SERVICE ONLY
6A 86234390 23725 1 CORD ASM, 16/3 SJTW X 2M IEC
6B 86217090 23726 1 CORD ASM, 16/3 AUST X IEC
6C 86217100 23727 1 CORD ASM, 16/3 UK X IEC
6D 86217110 23728 1 CORD ASM, 16/3 EURO X IEC
7 86274290 70162 4 SCR, 10-32 X 3/8 PPHMS SS
8 86279190 87095 4 WASHER, #10 FLAT PLTD
9 86198450 20005 1 CLAMP, 5/16 NYLON
10 98408080 - 1 KIT, 17” SPE CHARGER **
11 86323400 - 1 BRKT, 17” CHARGER SPE RIGHT **
12 86323410 - 1 BRKT, 17” CHARGER SPE LEFT **
**CALL MANUFACTURER FOR SERIAL NUMBER
PRV
NO.
QTY DESCRIPTION
CHARGER, CURTIS 1608, 17
INCH
ONBOARD CHARGER
SERIAL
NO.
THAILAND,
AUSTRALIA, CHINA
MALAYSIA, HONG
INDONESIA,
NOTES:
TAIWAN, US
SERVICE PART
SERVICE PART
KONG,
SINGAPORE, UK
SERVICE PART
KOREA, EURO
SERVICE PART
86221970 17” SCRUBBER 10/12/09
5-30
WIRING–BATTERY CABLES
5-31
86221970 17” SCRUBBER 04/17/09
WIRING-BATTERY CABLES
REF PART NO. PRV NO. QTY DESCRIPTION
1 86260470 880268 1 WIRE ASM, 26.5 6G RNG X C TERM
2 86225330 78942 1 TRAY, BATTERY INJ MOLDED
3 86002540 23174 1 BATTERY CBL ASM, 2 X 21 W/ANDRSN
4 86002510 23125 1 WIRE, 4 X 15 B CLAMP X B CLAMP
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-32
WIRING-MAIN HARNESS- ALL EXCEPT QSC172, & SCHC172
2 BLK
1 RED
BRUSH
MOTOR
20 RED
SOLENOID
VALVE
8
7
21 BLK
10
4 BLK
5
3 RED
VAC
MOTOR
6
7
9
BRUSH
12
SWITCH
11 RED
BRUSH
MOTOR
BRUSH
REVERSE
1 RED
20 RED
25A
10 BLK
2 BLK
3 RED
POSITIVE
TERMINAL
85
CHARGING
INHIBIT
RELAY
VAC
MOTOR
30
87A
VAC
SWITCH
17 RED
86
25A
BATTERY
METER
NEGATIVE
TERMINAL
HOUR
METER
6 RED
3
2
4
1
BLK
4 BLK
21 BLK
21
3
BLK
RED
2 BLK
11
6
3
4
2
1
5-33
5 RED
POSITIVE
BATTERY
CABLE
86221970 17” SCRUBBER 10/12/09
NEGATIVE
BATTERY
CABLE
13
WIRING-MAIN HARNESS-ALL EXCEPT QSC172, & SCHC172
REF PART NO. PRV NO. QTY DESCRIPTION
1 86218890 880448 1 HARNESS, SCRUBBER 172
2 86261230 29242 1 DIODE ASM, 76031 X 76042
3 86261240 29243 1 DIODE ASM, 76031 X 76031
4 86261340 67457 1 RESISTOR ASM, 2.7K OHM 1 WATT
5 86268570 88401 1 WIRE, 3” BLK/14 76029 X 76029
6 86267420 880283 2 WIRE, 3.5 BLK/18 76011 X 76040
7 86267410 880282 2 WIRE, 6” RED/14 76010 X 76029
8 86267620 880306 1 WIRE, 5.5 BLK/14 76001 X 76029
9 86268380 88286 1 WIRE, 4” RED/14 76029 X 76029
10 86226170 880447 1 WIRE, 5” RED/18 76031 X 76047
11 86226190 880450 1 WIRE, 11.5” RED/14 76001 X 76029
12 86268030 880456 1 WIRE, 14” RED/10 76081 X 76064
13 86226210 880457 1 WIRE, 9” RED/12 76064 X 76076
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-34
WIRING-MAIN HARNESS-SCHC172
5
7
7
11
6
13
15
10
9
2
1
8
12
13
6
3
4
5-35
86221970 17” SCRUBBER 10/12/09
14
WIRING-MAIN HARNESS-SCHC172
REF PART NO. PRV NO. QTY DESCRIPTION
1 86218890 880448 1 HARNESS, SCRUBBER 172
2 86261230 29242 1 DIODE ASM, 76031 X 76042
3 86261240 29243 1 DIODE ASM, 76031 X 76031
4 86261340 67457 1 RESISTOR ASM, 2.7K OHM 1 WATT
5 86268570 88401 1 WIRE, 3” BLK/14 76029 X 76029
6 86267420 880283 2 WIRE, 3.5 BLK/18 76011 X 76040
7 86267410 880282 2 WIRE, 6” RED/14 76010 X 76029
8 86267620 880306 1 WIRE, 5.5 BLK/14 76001 X 76029
9 86268380 88286 1 WIRE, 4” RED/14 76029 X 76029
10 86267360 880271 1 WIRE, 14” BLK/18 76011 X 76040
11 86226170 880447 1 WIRE, 5” RED/18 76031 X 76047
12 86226190 880450 1 WIRE, 11.5” RED/14 76001 X 76029
13 86268030 880456 2 WIRE, 14” RED/10 76081 X 76064
14 86226210 880457 1 WIRE, 9” RED/12 76064 X 76076
15 86014120 - 1 WIRE, 6” RED/10 76064 X 76064
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-36
WIRING-MAIN HARNESS-QSC172
5-37
86221970 17” SCRUBBER 04/17/09
WIRING–MAIN HARNESS QSC172
REF PART NO. PRV NO. QTY DESCRIPTION
1 86218890 880448 1 HARNESS, SCRUBBER 172
2 86261230 29242 1 DIODE ASM, 76031 X 76042
3 86261240 29243 1 DIODE ASM, 76031 X 76031
4 86261340 67457 1 RESISTOR ASM, 2.7K OHM 1 WATT
5 86268570 88401 1 WIRE, 3” BLK/14 76029 X 76029
6 86267420 880283 2 WIRE, 3.5 BLK/18 76011 X 76040
7 86267410 880282 2 WIRE, 6” RED/14 76010 X 76029
8 86267620 880306 1 WIRE, 5.5 BLK/14 76001 X 76029
9 86268380 88286 1 WIRE, 4” RED/14 76029 X 76029
10 86226170 880447 1 WIRE, 5” RED/18 76031 X 76047
11 86267430 880284 2 WIRE, 4.5 RED/14 76001 X 76029
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-38
WIRING-SCHEMATIC- ALL EXCEPT QSC172, & SCHC172
VAC
MOTOR
WIRE 3
BRUSH
MOTOR
WIRE 1
WIRE 4
WIRE 2
SOLENOID
VALVE
WIRE 20
WIRE 21
BATTERY
METER
86226170 - PRV NO. 880447
86267420
PRV NO. 880283
2
3
1
4
WIRE 17
VACUUM
86267410
PRV NO. 880282
86267410
PRV NO. 880282
25A
86268570
PRV NO. 88401
WIRE 2
BRUSH
REVERSE
86267620
86268570 - PRV NO. 88401
BRUSH
86268380
PRV NO. 88286
WIRE 4
86267420 - PRV NO. 880283
WIRE 3
86267410
PRV NO. 880282
25A
PRV NO. 880306
86267410
PRV NO. 880282
POSITIVE
TERMINAL
WIRE 11
WIRE 5
WIRE 1
86261230
PRV NO. 29242
86261240
HOUR
METER
86267420 - PRV NO. 880283
PRV NO. 29243
2
3
1
WIRE 6
WIRE 5
NEGATIVE
86261340
PRV NO. 67457
WIRE 10
86267420
PRV NO. 880283
WIRE 10
86267620 - PRV NO. 880306
WIRE 4
86267420 - PRV NO. 880283
86267620 - PRV NO. 880306
WIRE 21
TERMINAL
86226210 - PRV NO. 880457
86268030 - PRV NO. 880456
86266190 - PRV NO. 880450
RELAY
86
87A
30
85
BLACK FROM CHARGER
5-39
86221970 17” SCRUBBER 10/12/09
86260470 - PRV NO. 880268
BATTERY
POWER
RED FROM CHARGER
BLACK FROM CHARGER
BATTERY
AC INPUT
CHARGER
WIRING-SCHEMATIC-SCHC172
BATTERY
METER
86266170
PRV NO. 880447
86267420
PRV NO. 880283
2
3
1
4
VACUUM
86267410
PRV NO. 880282
VAC
MOTOR
WIRE 3
WIRE 17
WIRE 3
WIRE 4
86267420 - PRV NO. 880283
WIRE 4
86268570
PRV NO. 88401
BRUSH
REVERSE
BRUSH
86268380
PRV NO. 88286
86267410
WIRE 2
PRV NO. 880282
BRUSH
MOTOR
WIRE 2
WIRE 11
86267620
PRV NO. 880306
WIRE 5
WIRE 1
WIRE 1
86261230
PRV NO. 29242
WIRE 10
WIRE 10
86267620
PRV NO. 880306
SOLENOID
VALVE
WIRE 20
86267420
PRV NO. 880283
HOUR
METER
WIRE 21
86261240
PRV NO. 29243
WIRE 6
WIRE 5
86261340
PRV NO. 67457
86267410
PRV NO. 880282
NOT USED
GREEN
YELLOW
ORANGE
25A
86267410
PRV NO. 880282
25A
RELAY
RED
WHITE
BLACK
86268030
PRV NO. 880456
86
87A
30
85
86226210 - PRV NO. 880457
86014120
86226190 - PRV NO. 880450
RELAY
86
87A
30
85
RED FROM CHARGER
86267360 - PRV NO. 880271
POSITIVE
TERMINAL
BATTERY
POWER
86260470
PRV NO. 880268
86262830 - PRV NO. 880283
WIRE 4
86267620 - PRV NO. 880306
WIRE 21
86267420 - PRV NO. 880283
AC INPUT
NEGATIVE
TERMINAL
BLACK FROM CHARGER
BLACK FROM CHARGER
BATTERY
CHARGER
86221970 17” SCRUBBER 10/12/09
5-40
WIRING-SCHEMATIC-QSC172
VAC
MOTOR
WIRE 3
WIRE 4
86267420
PRV NO. 880283
BATTERY
METER
86266170 - PRV NO. 880447
2
3
1
4
VACUUM
86267410
PRV NO. 880282
WIRE 17
86267420 - PRV NO. 880283
WIRE 3
WIRE 4
86268570
PRV NO. 88401
BRUSH
REVERSE
BRUSH
86268380
PRV NO. 88286
WIRE 2
86267410
PRV NO. 880282
BRUSH
MOTOR
WIRE 2
WIRE 11
86267620
PRV NO. 880306
SOLENOID
VALVE
WIRE 1
WIRE 1
86261230
PRV NO. 29242
WIRE 10
WIRE 10
86267620
WIRE 5
PRV NO. 880306
WIRE 20
86267420
PRV NO. 880283
HOUR
METER
WIRE 21
86261240
PRV NO. 29243
WIRE 6
WIRE 5
86261340
PRV NO. 67457
86267410
25A
PRV NO. 880282
86267430 - PRV NO. 880284
POSITIVE
TERMINAL
BATTERY
POWER
25A
86267410
PRV NO. 880282
86267430 - PRV NO. 880284
86260470 - PRV NO. 880268
WIRE 4
86267420 - PRV NO. 880283
86267620 - PRV NO. 88 0306
WIRE 21
86267420 - PRV NO. 880283
NEGATIVE
TERMINAL
5-41
86221970 17” SCRUBBER 04/17/09
SUGGESTED SPARE PARTS
PART NO. PRV NO. DESCRIPTION
86215680 140931 BREAKER, 25A 250VAC 50VDC
86135310 140686 BRUSH SET, 24/36V VAC, WINDSOR
86001360 140394 BRUSH SET, CCL MOTORS
86002510 23125 WIRE 4 X 15 BCLAMP X BCLAMP
86002540 23174 WIRE ASM 2X21 BATTERY W/ ANDERSON
86003630 34351 FLOAT SHUT-OFF
86003760 35166 GASKET, VAC MTR
86003980 35249 GASKET, SQG. .13 THK X 8.00 LG
86219690 48080 KNOB, 1.5 OD X 5/16-18
86242100 48083 KNOB, SOLUTION LEVER
86007320 730029 SKIRT, 17 IN SCRUBBER
86224610 730359 SPRING, BRUSH CLIP
86007350 730040 STRAINER, 3/8” NPT 20 MESH
86007360 730057 BLADE, SQUEEGEE FRONT
86007610 730227 BLADE, SQUEEGEE REAR
86252520 80885 SAFETY DECAL, BATTERY CAUTION
86252540 81505 SAFETY DECAL, SOLUTION WARNING
SERIAL NO.
FROM
NOTES:
86221970 17” SCRUBBER 04/17/09
5-42
NOTES
REF.
NO.
1 1.006-627.0: 10066270000010, 1.006-630.0: 10066300000085, 1.006-631.0: 10066310000054, 1.006-
632.0: 10066320001169, 1.006-633.0: 10066330000029
MODEL: SERIAL #:
5-43
86221970 17” SCRUBBER 06/22/10
Loading...