Windsor NMWU2215N, 10066700 Operator Instructions Manual

150 PSI - 17 Gallon
Operating instructions (ENG)
MODELS:
NMWU2215N
10066700
86330780-D 09/22/11
Read these instructions before using the machine.
Machine Data Log/Overview
OVERVIEW
The Dominator is an electric powered carpet extractor intended for commercial use. This appliance applies a cleaning solution to the carpet and then vacuums the soiled water back into the recovery tank.
Warranty Registration
Thank you for purchasing a Windsor product. Warranty registration is quick and easy.
Your registration will allow us to serve you better over the lifetime of the product.
www.windsorind.com/WarrantyRegistration.aspx
2 86330780 DOMINATOR 150 PSI
To register your product go to :
For customer assistance:
1-800-444-7654
Table of Contents
Machine Data Log/Overview. . . . . . . . . . . . . . . . . . .2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . .4
Safety
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5
HAZARD INTENSITY LEVEL. . . . . . . . . . . . . . . . . .6
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . .8
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . . .9
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . .11
Chemicals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Pre-Run Inspection. . . . . . . . . . . . . . . . . . . . . . . . .12
Equipment Set-up. . . . . . . . . . . . . . . . . . . . . . . . . .12
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PARTS
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Solution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Vacuum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Suggested Spare Parts. . . . . . . . . . . . . . . . . . . . . 38
Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Maintenance
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . .14
Daily/Regular Maintenance. . . . . . . . . . . . . . . . . . .14
Vacuum Motor Replacement . . . . . . . . . . . . . . . . .15
Solution Pump Replacement . . . . . . . . . . . . . . . . .16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .17
86330780 DOMINATOR 150 PSI 3
How to Use This Manual
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
Serial Number Tag
This manual contains the following sections:
How to Use This Manual
•Safety
Operations
Maintenance
•Parts List
The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.
The model and serial number of your machine is located approximately where shown.
The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death.
The OPERAT IONS section is to familiarize the operator with the operation and function of the machine.
The MAINTENANCE section contains preventive main­tenance to keep the machine and its components in good working condition. They are listed in this general order:
Maintenance
•Lubrication
Vacuum Motor Replacement
Solution Pump Replacement
Troubleshooting
The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:
REF – column refers to the reference number on the parts illustration.
PART NO. – column lists the part number for the part.
PRV NO. – reference number.
QTY – column lists the quantity of the part used in that area of the machine.
DESCRIPTION – column is a brief description of the part.
SERIAL NO. FROM – If this column has an (*) and a Reference number, see the SERIAL NUMBERS page in the back of your manual. If column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustra­tion is shown, it displays the older design.
NOTES – column for information not noted by the other columns.
NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.
4 86330780 DOMINATOR 150 PSI
NOTE: The manual part number is located on the lower left corner of the front cover.
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before mainte-
nance or service.
Use only indoors. Do not use outdoors or expose to rain. Do not allow machine to be used as a toy. Close attent ion is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer's recommended components and attach­ments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around
sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces. Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow. This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust. Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use , for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.
not working properly, has been dropped, damaged, left outdoors, or
Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
86330780 DOMINATOR 150 PSI 5
Safety
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in min or personal in jury or pr oduct or pr operty damage. FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equip­ment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects.
WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jacket s, shirts, or sl eeves when wor king on the mac hine. Use only manufacturer approved replacement parts.
6 86330780 DOMINATOR 150 PSI
Safety Labels
Label Circuit Interrupter 86200570 PRV # 170-41
Label Warning 86244300 PRV # 500955
W ARNING!
FOR YOUR PROTECTION USE A GROUND FAULT CIRCUIT INTERRUPTER
Safety
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them.
86330780 DOMINATOR 150 PSI 7
Safety
Grounding Instructions THIS PRODUCT IS FOR COMMERCIAL
USE ONLY. ELECTRICAL:
In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunc­tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordi­nances.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig. A". A temporary adaptor that looks like the adaptor in "Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.
8 86330780 DOMINATOR 150 PSI
Technical Specifications
Height
Length
Width
ITEM MEASURE
Electrical 115 Volt, 60 hz, 15A Solution Pump 150 psi Solution Capacity 17 Gal Recovery Capacity 14 Gal Height 43 inches Length 32.5 inches Width 22.5 inches Vaccum Motor Dual 2 Stage Weight- Empty 120lbs Weight-Full Solution 261 lbs Power cord 1 X 25 feet
Operations
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for thier safety.
86330780 DOMINATOR 150 PSI 9
Operations
6
7
5
4
3
2
1
Controls
1. Vacuum Accessory Tool Hook-up
2. Solution Pump Switch
3. Vacuum 1 Switch
4. Vacuum 2 Switch
5. Breaker for Vacuum 2
6. Breaker for Vacuum 1
7. Solution Accessory Tool Hook-up
10 86330780 DOMINATOR 150 PSI
Machine Operation
Care must be exercised in the use of all chemicals. Chemicals are poisonous and can pose a health risk. Read and follow manfacturers instructions regarding dangers and correct usages.
The internal parts of the pump used in the mach ine are suitable for use with most carpet cleaning chemicals. But they are susceptible to chemical attack from some cleaning substances, such as hydrocarbon solvents and chlorinated bleaches. These non-compatible materials are not of the type used for carpet cleaning.
Chemicals Suitable Chemicals
Alkalis
Detergents
Hydroxides
•Soaps
Vinegar
Operations
Only use chemicals approved for use with this machine. Use of non-compatible chemicals may cause machine damage and will not be covered under the warranty. Carefully read ingredients on manfacturer's label before using any product in this machine.
Do not let pump run dry.
Do not let pump run unattended.
Non-Compatible
Aldehydes
Aromatics Hydrocarbons
SP Butyls
Carbon Tetrachloride
Clorox*
Chlorinated Bleaches
Chlorinated Hydrocarbons
•Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
Trichlorethylene
D-Limonene
*Registered Trademark
86330780 DOMINATOR 150 PSI 11
Operations
Pre-Run Inspection
1. Check all fittings and connectors for proper assembly.
2. Check all hoses for leaks. Repair or replace any damaged hoses.
3. Check power cord(s) for any damage. If damaged, replace.
Equipment Set-up
1. Plug power cord from machine into properly grounded wall outlet.
2. Turn vacuum motor switch on and off to make sure there is electrical power at machine.
3. Connect vac hose to machine. Slide the swivel cuff over the outlet on the tank.
4. Connect the hose to your machine and wand. Pull back the knurled collar on the quick disconnect coupler and push onto the connection on the chassis. To avoid leaks, check that a positive connection was made.
NOTE: Wand orifice must be equivalent or larger than an 04 nozzle.
5. Using a clean container, fill the solution tank with clean hot water . Do not use water over 13 0°F. Mix in a non-foaming cleaning concentrate for use in hot water extraction machines, following the manu­facture's instructions printed on container.
NOTE: When using a powder cleaner, pre-mix with hot water in a clean container before adding to the solution tank.
Cleaning
Always use defoamer if foaming occurs. Foam will suspend large particles that may damage vacuum(s) as well as allow liquid into the vacuum motor(s) without activating the float shutoff.
1. Prior to cleaning, make certain that the nozzle is functioning properly.
a. To check, hold the wand about one foot above
the surface to be cleaned and open the wand valve. A full spray should be observed from the nozzle.
b. If the nozzle is not showing a full spray pattern,
adjust nozzle for proper pattern, clean, or replace nozzle.
2. Normally , chemical is applied on the push stroke of the wand when cleaning. Vacuuming is done on the pull stroke. For heavily soiled carpets the wand may be used in a scrubbing manner, applying chemical in both the push and pull stroke.
3. When cleaning, keep the working opening (wand mouth) flat on the surface being cleaned. Keep the wand moving when the valve is open.
4. The shutoff float inside the vacuum tank will impede the vacuum flow when the vacuum tank is full. When this occurs, empty the vacuum tank by opening the dump valve and dispose of the waste in a proper manner.
Once the vacuum tank has been emptied, you may once again proceed with cleaning.
6. Turn pump and vacuum switch(s) to the on position.
12 86330780 DOMINATOR 150 PSI
Notes:
86330780 DOMINATOR 150 PSI 13
Maintenance
Periodic Maintenance
Twice a month, flush a white vinegar solution (one quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the machin e. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow dry.
NOTE: Do not use pins, wires, etc. to clean nozzles as this could destroy the spray pattern.
Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. The electrical cable must be well insulated and cable connector screw ke pt tight. If the cable insulation is broken or frayed, repair or replace immediately. Don't take chances with elctrical fire or shock.
Daily/Regular Maintenance
Before making any repairs or adjustments to the machine, disconnect the power cords from the electrical source.
1. Empty unused cleaning solution from the solution tank.
2. Inspect and clean filter screen in solution tank.
3. Flush pumping system with 1 to 2 gallons of clean water.
4. After each use, rinse tank with fresh water. Period­ically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a 10-1 bleach to water solution. Waste water should be disposed of properly.
Do not allow machine to freeze.
SERVICE SCHEDULE DAILY WEEKLY QUARTERLY
Check machine for cord damage * Check recovery dome and gasket for damage and cleanliness * Check hoses for wear, blockages, or damage * Check handles, switches, and knobs for damage * Run one gallon of water through system * Clean out recovery tank and check float valve to make sure it moves freely * Clean out solution tank and remove and clean vacuum intake screen * Clean outside of all tanks and check for damage * Run vac motor for at least one minute to allow motor to dry * Store with dome off tank to allow the tank to dry * Check all gaskets for wear and leakage * Check pump pressure; observe spray pattern and check with gau ge if
necessary Check and clean solution screen * Check cables for fraying * Check overall performance of machine * Check vac motor carbon brushes *
*
14 86330780 DOMINATOR 150 PSI
Only qualified maintenance personnel are to
Vacuum Motor Carbon Brushes Replacement
3 8
[9.5mm]
Carbon Brushes
End Cap
WARNING: The green ground wire must be attached for safe operation. See wiring diagram.
If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.
Important: These brushes wear quicker as the length shortens
due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.
Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.
perform the following repairs.
Vacuum Motor Replacement
1. Turn off all switches and unplug machine.
2. Remove hardware under front of machine to access component compartment.
3. Remove vacuum motor cover and disconnect motor wires.
4. Remove the vacuum motor.
5. Reverse process to install vacuum motor.
Maintenance
86330780 DOMINATOR 150 PSI 15
Maintenance
Solution Pump Replacement
Only qualified maintenance personnel are to perform the following repairs.
PUMP REPLACEMENT KITS 150 PSI
Bypass Valve Kit 86258830 PRV NO. 84161
16 86330780 DOMINATOR 150 PSI
Diaphragm Kit 86235100 PRV NO. 29206
Maintenance
Troubleshooting
PROBLEM CAUSE SOLUTION
Unit not plugged in Connect unit to 3 prong grounded outlet.
Loss of Power
Electrical shock
Vac motor speed varies or doesn't run
Loss of vacuum
Pump runs no solution
Pump runs, loss of pressure
Pump will not run
Solution hose fitting hard to connect
Carpet not getting clean
Carpet too wet Over saturation Make several passes without spray Carpet browning
Solution not flowing properly
Dead electrical circuit Check building circuit breaker or fuse box. Faulty power cord Replace Receptacle not grounded Contact an electrician to check building's wiring
Internal wiring problem Vacuum circuit breaker tripped Reset Breaker
Faulty vacuum motor Replace Faulty switch Replace Loose vacuum dome Center and seal dome over tank
Crack in dome or poor joint Lint or dirt clogging vacuum screen With power off clean screen
Loose cuffs on vacuum hose Tighten cuffs turning counterclockwise Vac motor seals leaking Replace Floor tool vac chamber clogged Wash out with hose. Pick lint out with a wire Vacuum hose damaged Replace Recovery tank full / Float ball stuck in
the up position Pump inlet screen plugged Clean inlet screen
Pump not primed Internal or external solution line
damaged and leaking Internal pump components wearing out Replace, see pump kit components Faulty switch Replace
Loose wiring Repair or replace
Corrosion on fittings.
Severe soil conditions
Leaving carpet too wet Check for loss of vac pressure Too much chemical Check label for correct solution concentration Solution hose connection Check for positive connection Faulty pump Repair or replace Faulty floor tool valve / Nozzle Repair or replace Faulty pump switch Repair
Have a trained service technician check machine's wiring
Replace or repair using acrylic plastic cement only
Turn off power, drain recovery tank.
Press trigger to open valve on cleaning wand to relieve air lock.
Replace
Clean with steel wool. Soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant.
Make several passes at right angles to each other. Use a pre-spray.
86330780 DOMINATOR 150 PSI 17
Notes:
18 86330780 DOMINATOR 150 PSI
PARTS
86330780 DOMINATOR 150 PSI
Control Panel
5
2
11
10
10
1
4
12
6
3
7
8
9
20 86330780 DOMINATOR 150 PSI
Control Panel
REF PART NO. PRV NO. QTY DESCRIPTION
1 86202230 390-09A 2 WASHER 9/16 S/S USS THICK 2 86002370 20035 1 CLAMP, 7/16 DIA NYLON UL 3 86002450 22015 1 COUPLER, 1/4 QD 4 86197390 31021 1 ELBOW, 1/4NPT 45D STREET 5 86005700 57104 2 NUT, 10-32 HEX W/ STAR 6 86276820 70740 6 SCR, 10-32 X 1/2 PTHMS BLK NP 7 86007140 72130 3 SWITCH, SPST 2-POSITION ROCKER 8 86008900 80845 2 BOOT, SEAL PUSH BUTTON 7/16
9 86323520 - 1 PANEL, CONTROL, 150 10 86313020 - 2 GASKET, .125 T X .25 W X 15.6 11 86313030 - 4 GASKET, .125 T X .25 W X 7.2 12 86318320 - 2 BREAKER, 13A, 250VAC, 32VDC
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 21
Electrical
16
6
15
14
13
10
3
1
12
9
17
5
7
11
2
4
8
3
18
19
22 86330780 DOMINATOR 150 PSI
Electrical
REF PART NO. PRV NO. QTY DESCRIPTION
1 86201510 390-26 2 SPACER NYLON 1/4ID X 1/2 OD 2 86005670 57040 1 NUT, 1/2 NPT CONDUIT 3 86005700 57104 3 NUT, 10-32 W/STAR WASHER PLTD 4 86273830 70020 2 SCR, 1/4-20 X 1/2 HHCS SS 5 86006850 70393 2 SET SCR, 1/4-20 X 1.25L 6 86256200 73200 1 STRAIN RELEIF, 1/2 NPT FLEX 7 86255900 73538 2 STANDOFF, 6-32 X 5/8 HEX NYL 8 86010630 87013 2 WASHER, 1/4 X 5/8 FLAT SS 9 86316460 - 1 BRKT, ELECTRICAL
10 86316540 - 1 CONNECTOR, 5 POS, PUSH WIRE 11 86316700 - 1 BRKT, CORD STRAIN RELIEF 12 86318620 - 1 CORD ASM, 14/3 SJT X 25' BLK 13 86319090 - 1 FUSE HOLDER, PANEL MNT 14 86319110 - 1 FUSE, 1/4" X 1 1/4", 4A 15 86317580 - 1 BRKT, CORD, BLANK 16 86005810 57245 2 NUT, 1/4-20 NYLOCK 17 86323330 - 2 WASHER, 1/4" ID X 1.0D FLAT BLK 18 86198460 20008 1 CLAMP, 5/8 NYLON UL/CSA 19 86006590 70088 1 SCREW 10-32 X 1/2 PPHMS SS NP
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 23
Frame
1
2
3
4
5
6
7
8
9
10
11
24 86330780 DOMINATOR 150 PSI
Frame
REF PART NO. PRV NO. QTY DESCRIPTION
1 86199430 040-03 2 CASTER, SWIVEL 4" 250# CPCTY
2 86001660 41236 2 HUBCAP, 5/8 SHAFT
3 86005810 57245 8 NUT, 1/4-20 HEX NYLOCK SS
4 86276080 70595 1 SCR, 10-32 X 1” PPHMS GRN
5 86010630 87013 8 WASHER, 1/4 X 5/8 FLAT SS
6 86005700 57104 2 NUT, 10-32 HEX W/STAR
7 86010730 87088 4 WASHER, 5/8 X 1-3/16 FLAT SS
8 86219480 41567 2 HUBCAP, 9.75" WHEEL
9 86309790 - 2 WHEEL, 12" X 2.25” 10 86312830 - 1 FRAME, 5/8" AXLE, DUAL VAC 11 86277500 70853 8 SCR,1/4-20 X 5/8 CARR SS
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 25
Labels
1
2
3
26 86330780 DOMINATOR 150 PSI
Labels
REF PART NO. PRV NO. QTY DESCRIPTION
1 86321760 - 1 LABEL, DOM, RH 2 86321770 - 1 LABEL, DOM, LH 3 86330730 - 1 LABEL, DOM, 150
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 27
Pump
12
3
1
13
11
6
5
2
4
9
10
7
11
8
FROM SOLUTION TANK
TO SOLUTION FITTING
28 86330780 DOMINATOR 150 PSI
Pump
REF PART NO. PRV NO. QTY DESCRIPTION
1 86197290 14076 1 BUSHING, 3/8 MPT X 1/4 FPT HEX
2 86233150 20042 1 CLAMP, 3/8 WORM GEAR
3 86197360 31016 1 ELBOW, 1/4 NPT STREET
4 86282320 39710 1 HOSE, 1/2ID WIRE BOUND X 26"
5 86197940 40027 1 HOSEBARB, 3/8 MPT X 1/2 HOSE 90
6 86005640 57030 4 NUT, 10-32 HEX NYLOCK
7 86005710 57105 1 NUT, 1/4-20 HEX W/STAR WASHER
8 86274450 70202 4 SCR, 10-32 X 1.25 HHMS PLTD
9 86233410 81270 1 CLAMP, 3/4 DIA CUSHION .406 DIA 10 86010630 87013 1 WASHER, 1/4 X 5/8 FLAT SS 11 86010650 87018 8 WASHER, #10 X 9/16 FLAT 12 86317880 - 1 HOSE,49.0 GRY3/8 1/4MPTX1/4MPT 13 86318630 - 1 PUMP, 115V 150PSI BYPASS
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 29
Recovery
21
10
17
9
7
1
10
12
13
10
5
20
16
14
8
2
4
19
3
15
18
11
6
30 86330780 DOMINATOR 150 PSI
Recovery
REF PART NO. PRV NO. QTY DESCRIPTION
1 86161460 15-808123 1 DUMP VALVE, 1 1/2”
2 86002620 260-64A 1 ACCESS, COVER CLEAR 6" W/RIM
3 86197820 31002 1 ELBOW, 1.5 FPT X FS PVC
4 86004000 35255 1 GASKET, TANK LID
5 86197040 57264 2 NUT, 5/16-18 HEX ACORN PLTD
6 86273740 70010 2 SCR, 1/4-20 X 1.50 HHCS SS
7 86273750 70011 4 SCR, 1/4-20 X 5/8 HHCS SS
8 86275800 70546 6 SCR, 8 X 3/4 PFHT/S BLK ZINC
9 86010630 87013 4 WASHER, 1/4 X 5/8 FLAT SS 10 86010670 87029 6 WASHER, 5/16 X 3/4 SS 11 86323330 - 2 WASHER, 1/4 ID X 1.0 OD FLAT BLK 12 86011020 89202 2 WHEEL, 3" DIA. CUSHION RUBBER 13 86001350 140390 2 BUSHING, SPANNER .435 X 1.10 14 86311510 - 1 ADAPTER, FLOAT 30 DEG, 2” 15 86324960 - 1 TANK, RECOVERY, TRIMMED 16 86313040 - 1 SCRN, FLOAT, SHTOFF, 2” 17 86316710 - 2 BRKT, CORD, MOUNT 18 86317230 - 1 HOSEBARB,1.5MPT X 1.5 W/FLNG 19 86317720 - 2 SCR, 5/16-18 X 2.50 BSHCS SS 20 86320790 - 1 PIPE ASM, 2", VACUUM 21 86233120 20019 1 CLAMP, 2.75" WORM GEAR
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 31
Solution
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
1
22
23
13
6
32 86330780 DOMINATOR 150 PSI
Solution
REF PART NO. PRV NO. QTY DESCRIPTION
1 86173640 11-800437 1 ADPT,3/8 BLKHD COMPLETE
2 86233150 20042 1 CLAMP, 3/8 WORM GEAR
3 86238460 36259 2 HOOK, STRAP
4 86197940 40027 1 HOSEBARB, 3/8 MPT X 1/2 HOSE 90
5 86273740 70010 1 SCR, 1/4-20 X 1.50 HHCS SS
6 86273830 70020 11 SCR, 1/4-20 X 1/2 HHCS SS
7 86005810 57245 2 NUT, 1/4-20 HEX NYLOCK SS
8 86324210 - 4 SCR, 1/4-20 X 5/8 BHCS BLK
9 86276160 70604 2 SCR, 10-32 X 5/8 PPHMS BLK 10 86007970 73864 1 STRAINER, 3/8 IN. NPT 60 MESH 11 86233410 81270 2 CLAMP, 3/4 DIA CUSHION .406 DIA 12 86010670 87029 2 WASHER, 5/16 X 3/4 SS 13 86010630 87013 12 WASHER, 1/4 X 5/8 FLAT SS 14 86323330 - 2 WASHER, 1/4 ID X 1.0 OD FLAT BLK 15 86311990 - 1 HINGE, 9.5" LG X .074 THK 16 86312000 - 1 LID, SOLUTION, COVER 17 86312010 - 1 LID, SOLUTION, HINGE BRKT 18 86330160 - 1 TANK, 17G SOL, 150 TRIM, BLU 19 86297620 - 2 STRAP, HAND TOOL 20 86317560 - 1 SPACER, .50 ODX .28 ID X 1.0L 21 86318790 - 1 WASHER, 1.032ID X 1.5OD X .0 62THK 22 86242130 48100 2 KNOB, 1/4 HEX PRESS-LOC WING 23 86324030 - 2 PLATE, MOUNTING, SOLUTION
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 33
Vacuum
12
11
10
9
8
7
6
5
4
3
2
1
4
13
34 86330780 DOMINATOR 150 PSI
Vacuum
REF PART NO. PRV NO. QTY DESCRIPTION
1 86005810 57245 8 NUT, 1/4-20 HEX NYLOCK SS 2 86274090 70092 5 SCR, 10-32 X 1.5 PPHMS 3 86233430 81431 2 CLAMP, 2.50 WORM GEAR 4 86010630 87013 16 WASHER, 1/4 X 5/8 FLAT SS 5 86278990 8 7017 8 WASHER, #8 X 3/8 FLAT 6 86311520 - 1 MANIFOLD, VACUUM, DUAL 7 86312990 - 1 GASKET , VAC MANIFOLD, DUAL 8 86314710 - 8 SCR, 1/4-20 X 5.50 HHCS PLT 9 86317630 - 8 SCR, #8 X 3/4" PPHSMS TYPE AB
10 86318300 - 1 HOSE, VAC, 2.0 ID X 18"L 11 86318760 - 2 VAC ASM, 2-STAGE, 120V
- 86135320 140687 - SP BRUSHES SET (120V VAC)
12 86312080 - 2 COVER, VAC MOTOR 13 86312220 - 2 BASE, VAC MOTOR, 2 STAGE
- 86319020 - - VAC HOUSING, 2 STAGE INCLUDES 12, 13
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 35
Wiring Diagram
1
-VACUUM -VACUUM -PUMP SWITCH SWITCH SWITCH
-TERMINAL BLOCK
MOTOR MOTOR MOTOR
-POWER CORD
BLK
WHT
WHT/7 WHT/8
WHT
WHT
BLK
BLK-WHT
GRY-WHT
BLU/1 BLU-BLK/2 GRY/3
GRN
GRN
GRN GRN GRN
13AMP 13AMP
4AMP
-VACUUM -VACUUM -PUMP
-CB
-CB
-FUSE
MMM MMM MMM
36 86330780 DOMINATOR 150 PSI
Wiring Diagram
REF PART NO. PRV NO. QTY DESCRIPTION
1 98407900 - 1 HARNESS KIT, SINGLE CORD
SERIAL NO.
FROM
NOTES
86330780 DOMINATOR 150 PSI 37
Suggested Spare Parts
PART NO. PRV NO. DESCRIPTION
86135320 140687 BRUSH SET, 120V VAC 86199430 040-03 CASTER SWIVEL 4” 250# CAPACITY 86002620 260-64A ACCESS COVER CLEAR 6” W/RIM 86319110 - FUSE, 1/4” X 1-1/4”, 4A 86318760 - VAC ASSY 2-STG, 120V 86007140 72130 SWITCH, SPST 2-POSITION ROCKER 86309790 - WHEEL, 12” X 2.25” 86001660 41236 HUBCAP, 5/8” SHAFT 86007970 73864 STRAINER 3/8” NPT 60 MESH 86357300 - TERMINAL STRIP, 12 POST IDEAL CUT TO FIT
SERIAL NO.
FROM
NOTES
38 86330780 DOMINATOR 150 PSI
Serial Numbers
REF.
NO.
1N/A
MODEL: SERIAL #
86330780 DOMINATOR 150 PSI 39
Notes:
40 86330780 DOMINATOR 150 PSI
Loading...