Windsor Floor Polisher SP13-10090220, SP17IE-10090270, SP20-10090310, SP17X-10090280, SP15-10090230 Operating Instructions Manual

MODELS:
U17-10090580 SP13-10090220 SPT17-10090370 SP17IE-10090270
U20-10090600 SP15-10090230 SPT20X-10090380 SP17IA-10090260
U17X-10090590 SP17-10090240 SP17XIE-10090300
U20X-10090610 SP20-10090310 SP17XIA-10090290
UDS20-10090630 SP17X-10090280 SPDS17IE-10090340
SP20X-10090320 SPDS17IA-10090330
SPDS20-10090350 SP17HDIE-10090250

FLOOR POLISHE

R

Operating Instructions (ENG)

86309580-A
10/08/08

IPX4

MACHINE DATA LOG/OVERVIEW

86309580 FLOOR POLISHER 10/08/08

2

Model:
Date of Purchase:
Serial Number:
Sales Representative:
Address:
Phone Number:

TABLE OF CONTENTS

86309580 FLOOR POLISHER 10/08/08

3

Machine Data Log.............................2

Table of Contents..............................3

HOW TO USE THIS MANUAL

How to use this Manual.....................1-1

SAFETY

Important Safety Instructions............2-1

Hazard Intensity Level. .....................2-2

Grounding Instructions 120V. ...........2-3

Grounding Instructions 230V ............2-4

Safety Label Location .......................2-5

OPERATION

Technical Specifications ...................3-1

Handle Installation ............................3-2

Controls.............................................3-3

Handle Adjustment............................3-3

Machine Operation............................3-4

Pad Driver Installation.......................3-4

MAINTENANCE

Scrub Brush/Pads.............................4-1

Machine Troubleshooting..................4-2

GROUP PARTS LIST

Brush/Pad Driver Group....................5-1

Electrical – 120v................................5-3

Electrical – 230v................................5-5

Deck..................................................5-7

Handle...............................................5-9

Motor.................................................5-11

Wiring-120V......................................5-13

Wiring-230V......................................5-15

Suggested Spare Parts.....................5-14

HOW TO USE THIS MANUAL

86309580 FLOOR POLISHER 10/08/08

1-1

This manual contains the following sections:

- HOW TO USE THIS MANUAL

- SAFETY

- OPERATIONS

- MAINTENANCE

- PARTS LIST

The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.

Parts may be ordered from authorized dealers.
When placing an order for parts, the machine
model and machine serial number are important.
Refer to the MACHINE DATA box which is filled
out during the installation of your machine. The
MACHINE DATA box is located on the inside of
the front cover of this manual.

The SAFETY section contains important
information regarding hazard or unsafe practices
of the machine. Levels of hazards are identified
that could result in product or personal injury, or
severe injury resulting in death.

The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.

The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:

The PARTS LIST section contains assembled
parts illustrations and corresponding parts list. The
parts lists include a number of columns of
information:

- REF – column refers to the reference
number on the parts illustration.

- PART NO. – column lists the part
number for the part.

- PRV NO. - Reference No.

- QTY – column lists the quantity of the

part used in that area of the machine.

- DESCRIPTION – column is a brief
description of the part.

- SERIAL NO. FROM – If this column
has an (*) and a Reference number,
see the SERIAL NUMBERS page in
the back of your manual. If column
has two asterisk (**), call manufacturer
for serial number. The serial number
indicates the first machine the part
number is applicable to. The main
illustration shows the most current
design of the machine. When a boxed
illustration is shown, it displays the
older design.

- NOTES – column for information not
noted by the other columns.

NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.

NOTE: The number on the lower left corner of the
front cover is the part number for this manual.

SAFETY

86309580 FLOOR POLISHER 10/08/08

2-1

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

To reduce the risk of fire, electric shock, or injury:

Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.

If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water,
return it to an authorized service center.

Do not operate the machine with any openings blocked. Keep openings free of debri s that may reduce
airflow.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine
near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories,
shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.
During operation, attention shall be paid to other persons, especially children.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, unplug the machine.
Do not handle the plug or machine with wet hands.
Do not unplug machine by pulling on cord. To unplug, grasp the plug, not

the cord.

Do not use with damaged cord or plug. Follow all instructions in this manual concerning grounding the
machine.

Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edge s or
corners.

Do not pull/run machine over cord. Keep cord away from heated surfaces.
Connect to a properly grounded outlet. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

SAFETY

86309580 FLOOR POLISHER 10/08/08

2-2

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words – WARNING and CAUTION and

FOR SAFTEY. The level of hazard intensity is determined by the following definitions:

WARNING – Hazards or unsafe practices which COULD result in severe
personal injury or death.

CAUTION – Hazards or unsafe practices which could result in minor personal
injury or product or property damage.

FOR SAFETY: To identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the devices on the machine. Please take the necessary steps to train the machine
operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and Understood.
In Flammable or Explosive areas.
In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose fitting clothing, jackets, shirts, or sleeves when working
on the machine. Use approved replacement parts.

SAFETY

86309580 FLOOR POLISHER 10/08/08

2-3

GROUNDING INSTUCTIONS-120V

THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.

ELECTRICAL:
In the USA this machine operates on a one 15
amp nominal 120V, 60 hz, A.C. power circuit. The
amp, hertz, and voltage are listed on the data label
found on each machine. Using voltages above or
below those indicated on the data label will cause
serious damage to the motors.

GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to
reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment­grounding conductor and grounding plug. The
plug must be inserted into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.

This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like the
plug in “Fig. A”. A temporary adaptor that looks
like the adaptor in “Fig . C” may be used to
connect this plug to a 2-pole receptacle as shown
in “Fig. B”, if a properly grounded outlet is not
available. The temporary adaptor should be used
only until a properly grounded outlet (Fig. A) can
be installed by a qualified electrician. The green
colored rigid ear, lug, or the like extending from
the adaptor must be connected to a permanent
ground such as a properly grounded outlet box
cover. Whenever the adaptor is used, it must be
held in place by a metal screw.

Improper connection of the equipment­grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in doubt
as to whether the outlet is properly grounded.
Do not modify the plug provided with the
appliance - if it will not fit the outlet, have a
proper outlet installed by a qualified
electrician.

USING AN ADAPTOR

GROUNDING CONNECTION

Note: Ada

p

tors are not allowed in Canada.

Outlet

Tab for Grounding

Outlet Box

FIGURE C

Grounded

FIGURE A

Adaptor

Screw

FIGURE B

Adaptor

Metal Screw

Grounded

Grounding Pin

SAFETY

86309580 FLOOR POLISHER 10/08/08

2-4

GROUNDING INSTRUCTIONS-230V

THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.

ELECTRICAL:
The amp, hertz, and voltage are listed on the
data label found on each machine. Using
voltages above or below those indicated on the
data label will cause serious damage to the
motors.

EXTENSION CORDS:

If an extension cord is used, the wire size must
be at least one size larger than the power cord
on the machine, and must be limited to 50 feet
(15.5m) in length.

GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding
provides a path of least resistance for electric
current to reduce the risk of electric shock.
This appliance is equipped with a cord having
an equipment-grounding conductor and
grounding plug. The plug must be inserted
into an appropriate outlet that is properly
installed and grounded in accordance with all
local codes and ordinances.

Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug
provided with the appliance - if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.

SAFETY

86309580 FLOOR POLISHER 10/08/08

2

-

5

SAFETY LABEL LOCATION

NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time,
the labels become illegible contact your authorized representative for prompt replacement.

WARNING LABEL
P/N 86219740
PRV NO. 500194

TECHNICAL SPECIFICATIONS

86309580 FLOOR POLISHER 10/08/08

3

-

1

ITEM DIMENSION/CAPACITY/MODEL

CONSTRUCTION

Heavy-duty die cast aluminum deck with heavy­duty rubber bumper, tubular steel adjustable
handle with die cast aluminum handle housing

MOTOR

1HP 115V induction SP13, SP15, SP17, U17, SP17, SP20, U20

1.5HP 115V induction SP17X, U17X, SPT20X, SP20X, U20X

1.75 HP 115V 175/300RPM SPDS20, UDS20
1HP 230V induction SP17IA, SP17IE

1.5 HP 230V induction SP17HDIE, SP17XIA, SP17XIE

1.75 HP 230V 175/300RPM SPDS17IA, SPDS17IE

BRUSH/PAD SPEED

175 rpm

SP13, SP15, SP17, U17, SP17, SP20, U20,
SP17X, U17X, SPT20X, SP20X, U20X

146 rpm 230V

SP17HDIE , SP17IA, SP17IE, SP17XIA,
SP17XIE

175/300 rpm UDS20, SPDS20, SPDS17IA, SPDS17IE

ELECTRICAL SYSTEM

115 volts, 60 Hz

SP13, SP15,, SP17, U17,SPT17, SP17X, U17X,
SP20, U20, SPT20X, SP20X, U20X,
SPDS20, USD20

230 volts, 50Hz

SP17HDIE, SP17XIA, SPX17IE, SPDS17IE,
SP17IA, SP17XIA, SPDS17IA

CABLE

50’ (15 m), 14/3, built in cord wrap

SP13, SP15,, SP17, U17,SPT17, SP17X, U17X,
SP20, U20, SPT20X, SP20X, U20X,
SPDS20, USD20

75’ (22.9) 1.5mm³, built in cord wrap

SP17HDIE, SP17XIA, SPX17IE, SPDS17IE,
SP17IA, SP17XIA, SPDS17IA

SWITCHES

Dual levers with safety lock

WHEELS

Two 5” (12.7 cm) dia., 1.25” (3 cm) wide, non­marking tread

HANDLE

1.5” (4 cm) tubular steel, adjustable, easy to use

thumb activated safety lock
DIMENSIONS (L X W X H)
13” (33 cm) model 21.0” (53 cm) x 14” (36 cm) x 47” (119 cm)

15” (38 cm) model 22.0” (56 cm) x 16” (41 cm) x 47” (119 cm)
17” (43 cm) model 23.0” (58 cm) x 18” (46 cm) x 47” (119 cm)
20” (51 cm) model 24.5” (62 cm) x 21” (53 cm) x 47” (119 cm)