Wind n Go 7351 Operating Instructions Manual
Wind ‘N Go® 1-Watt Waterproof Flashlight #7351
IMPORTANT SAFEGUARDS
• Read all instructions before operating
• Do not look directly at the light; may cause injury to your eyes
• Do not use in flammable or explosive environments
• Do not operate at temperatures above 120°F or below 32°F
• Turn off flashlight before charging
• Do not use alcohol, flammable or other solvents on or near this unit-only clean with warm
water and soft cloth
• Protect LED lens from damage and scratching
• Administer close supervision when using around children
• Never use or submerge in water with DC CAP removed
PARTS IDENTIFICATION
CHARGING
Note: Before charging, turn flashlight off.
Dynamo charging by hand crank
1. Open DYNAMO HAND CRANK and rotate clockwise at approximately 120 cycles/minute
for a minimum of 1 minute. Winding for longer periods of time will yield longer power
durations.
2. Close DYNAMO HAND CRANK and unit is now ready for use.
3. If desired to verify that charging is taking place, remove the DC IN/OUT PORT cap to
exposes the small green LED charge indicator light. Caution: Close cap and seal completely
to assure waterproof integrity after charging and before use. Do not open cap under water.
4. Unit may also be charged under water.
AC/DC Adapter charging (adapter not included)
1. Charge the internal battery of the flashlight for increased standby power by using an
auxiliary AC/DC ADAPTER.
2. Remove the DC IN/OUT PORT cap to expose the DC IN/OUT PORT. Carefully plug the small
male connector of the AC/DC ADAPTER into the DC IN/OUT PORT. Plug the adapter into
an approved 120V AC power outlet. Verify that the charge is taking place by assuring the
small LED indicator light is illuminated. Close cap and seal completely to assure waterproof
integrity after charging and before use.
3. Full charge times are indicated in the specifications on the back page.
Charging a cell phone
1. Unit charges cell phones by using the DYNAMO HAND CRANK.
2. Flashlight includes a Nokia cell phone adapter tip to match most common Nokia phones.
3. To charge your phone, connect the Universal DC cable into the DC IN/OUT PORT of the
flashlight. Plug the other end of the cable directly into the Nokia phone, or the appropriate
adapter tip for your phone.
4. Wind the flashlight DYNAMO HAND CRANK for a minimum of 1–3 minutes for a 1-5
minute phone call, depending on cell phone model. Longer cranking duration will increase
talk time ability.
FLASHLIGHT OPERATION
Press the ON/OFF BUTTON located on front of flashlight.
• Press once to activate the 2 left and right side LEDs
• Press twice to activate center 1-watt single LED
• Press third time to activate 1-watt single LED with flashers
• Press fourth time to turn flashlight off
Dynamo Hand
Crank
On/Off Button
1-Watt LED
2 - Standard
LEDs
Wrist
Strap
DC In/Out Port
OPERATING INSTRUCTIONS
TECHNICAL INFORMATION
SPECIFICATIONS
INTERNAL RECHARGEABLE
BATTERY
3.6V 800mAh Ni-Mh
DC INPUT 6V 200 mA
DC OUTPUT 6V 700-800 mA
WEIGHT 11 oz.
DIMENSIONS 7” L x 3” W x 2.25” H (173 x 69 x 56.5 mm)
BRIGHTNESS IN MCD 1-watt center LED = 250,000 MCD (20 lm)
2 side LEDs = 30,000 MCD (4 lm)
POWER DURATION FLASHLIGHT FLASHER
1 minute winding 1-watt center LED = 20 minutes
2 side LEDs = 50 minutes
1-watt center LED = 50 minutes
AC/DC Charge
(Full charge = 8 hours)
1-watt center LED = 8 hours
2 side LEDs = 40 hours
1-watt center LED = 40 hours
CELL PHONE CHARGING
1-3 minutes of
winding
3-7 minutes of emergency talk time.
Longer talk times may be achieved with additional winding.
AERVOE INDUSTRIES, INC.
Gardnerville, NV 89410 • 1-800-227-0196
www.aervoe.com • mailbox@aervoe.com
7351inst; cs6/15
1-Watt Waterproof
Flashlight
Wind ‘N Go is a registered trademark of Aervoe Industries, Inc.
Loading...