Wincomm WMP-19B, WMP-22B User Manual

WMP-19B/22B

Medical Panel PC

USER’S MANUAL

V1.0

Copyright© ,2016. All rights reserved

All other brand names are registered trademarks of their respective owners.

The information contained in this document is subject to change without notice

ii

Date

Version

Description

Remark

2016/5/31

1.0

First release

James

Version Change History

WMP-19B/22B User’s manual

iii

Acknowledgments

 Intel® Celeron processor is registered trademarks of Intel®

Corporation.

 IBM, PC/AT, PS/2 are trademarks of International Business

Machines Corporation.

 Microsoft

®

Windows is a registered trademark of Microsoft

Corporation.

 RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
 C&T is a trademark of Chips and Technologies, Inc.
 UMC is a trademark of United Microelectronics Corporation.
 ITE is a trademark of Integrated Technology Express, Inc.
 Intel is a trademark or registered trademark of Intel

Corporation.

 Microsoft Windows is a registered trademark of Microsoft

Corporation.

®

 Winbond is a registered trademark of Winbond Electronics

Corporation.

All other product names or trademarks are properties of
their respective owners.

WMP-19B/22B User’s manual

iv

FCC Class B

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 18 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment.
This equipment generates, uses and can radiate radio frequency energy. If
not installed and used in accordance with this user manual, it may cause
harmful interference to radio communications.
Note that even when this equipment is installed and used in accordance
with this user manual, there is still no guarantee that interference will not
occur. If this equipment is believed to be causing harmful interference to
radio or television reception, this can be determined by turning the
equipment on and off. If interference is occurring, the user is encouraged
to try to correct the interference by one or more of the following measures:

 Increase the separation between the equipment and the receiver
 Connect the equipment to a power outlet on a circuit different from

that to which the receiver is connected

 Consult the dealer or an experienced radio/TV technician for help

Warning:

Any changes or modifications made to the equipment which are
not expressly approved by the relevant standards authority could
void your authority to operate the equipment.

To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.

Do not modify this equipment without authorization of the
manufacturer.

WMP-19B/22B User’s manual

v

Safety Instructions

Intended use

The WMP-19B/22B is intended to serve as a medical monitor
which is designed for general purpose for hospital environment. It
shall not be used for life-supporting system.

Intended User profile

The equipment is intended for infant or adults by profession
Health care professionals.

Greeting & Setup

Thank you for purchasing the WMP-19B/22B unit. We wish that
this unit will be durable and reliable in providing your medical
application needs. Please follow the instructions below to ensure
the unit continues to have high performance.

Unpacking

After opening the carton, there will be a medical panel PC unit
with an accessory box. Examine the contents to see if there are
damages to the unit and if all accessories are present.

Setting up

Please read this manual carefully and remember to keep this
manual for future reference.

Safety Instructions & Cleaning

The unit has undergone various tests in order to comply with
safety standards. Inappropriate use of the open frame unit may
be dangerous. Please remember to follow the instructions below
to insure your safety during the installation and operating
process.

Transporting & Placement of unit

1. When moving the unit on a cart; be very cautious. Quick

stops, excessive forces and uneven surfaces may cause
the cart to overturn thus risking the unit to fall to the
ground.

2. If the medical panel PC unit does fall to the ground,

immediately turn the power off and disconnect cords. Then

WMP-19B/22B User’s manual

vi

contact a service technician for repairs. Continual use of
the unit may result cause a fire or electric shock. Also, do
not repair the unit on your own.

3. Having two or more people transporting the display unit is

recommended. In addition, when installing the unit by
suspending it also requires two or more people.

4. Before suspending the unit, make sure the material used

for suspension is sturdy and stable. If not properly
suspended, the display unit may fall and cause serious
injury to people standing nearby as well as to the unit
itself.

5. If you wish to mount the display unit, remember to use

only the mounting hardware recommended by the
manufacturer.

Electrical and Power Source Related

1. This medical panel PC unit must operate on a power source

as shown on the specification label. If you are not sure
what type of power supply used in the area, consult your
dealer or local power supplier.

2. The power cords must not be damaged. Applied pressure,

added heat, and tugging may damage the power cord.

3. The power cord must be routed properly when setup takes

place. We advise that this aspect measure is to prevent
people from stepping on the cords or while the unit is
suspended to prevent flying objects from getting tangled
with the unit.

4. For plug-in equipment, the power outlet socket must be

located near the equipment and must be easily accessible.

5. Do not overload the AC outlets or extension cords.

Electrical shocks or fires may occur from overloading.

6. Do not touch the power source during a thunderstorm.

7. If your hands are wet, do not touch the plug.

8. Use your thumb and index finger, grip firmly on the power

cord to disconnect from the electrical socket. By pulling the
power cord, may result in damaging it.

WMP-19B/22B User’s manual

vii

9. If the unit is not going to be in use for an extended period

of time, remember to disconnect the unit.

10. The medical panel PC unit uses voltage between

100-240VAC. Connect the unit to a power source with the
same numerical value as shown. Please use only the power
cord provided by the dealer to ensure safety and EMC
compliance.

Various Factors of Environment

1. Do not insert objects into the openings.

2. Do not have liquids seep into the internal areas of the

medical panel PC unit.

3. Having liquids seep in or inserting objects into the unit

may result in electric shocks from taking and/or short
circuiting the internal parts.

4. Do not place the medical panel PC unit in the presence of

high moisture areas.

5. Do not install the medical panel PC unit in a wet

environment.

6. Do not place near unit near heat generating sources.

7. Do not place the unit in a location where it will come in

contact with fumes or steam.

8. Remember to keep the medical panel PC unit away from

the presence of dust.

9. If water has flow in or seep in, immediately disconnect the

open frame unit. Then contact a service technician for
repairs.

Ventilation Spacing

1. Do not cover or block the openings on the top and back

sides of the display unit. Inadequate ventilation may cause
overheating thus reducing the lifespan of the unit.

2. Unless proper ventilation is present, do not place unit in an

enclosed area; such as a built-in shelf. Keep a minimum
distance of 10 cm between the display unit and wall.

WMP-19B/22B User’s manual

viii

No power

1. Connect the AC adapter to the computer, and
then plug it into an AC outlet.

2. Turn on the computer.

Operating principle

 A Medical Panel PC has four main components: the

arithmetic logic unit (ALU), the control unit, the memory,
and the input and output devices (collectively termed I/O).
These parts are interconnected by buses, often made of
groups of wires.

 The control unit, ALU, and registers are collectively known as

a central processing unit (CPU).

 Inside each of these parts are thousands to trillions of small

electrical circuits which can be turned off or on by means of
an electronic switch. Each circuit represents a bit (binary
digit) of information so that when the circuit is on it
represents a "1", and when off it represents a "0" (in positive
logic representation). The circuits are arranged in logic gates
so that one or more of the circuits may control the state of
one or more of the other circuits.

Cleaning the unit

1. Remember to turn off the power source and to unplug the

cord from the outlet before cleaning the unit.

2. Carefully dismount the unit or bring the unit down from

suspension to clean.

3. Please use a dry soft cloth to clean the unit.

4. Take a dry cloth and wipe the unit dry. Remember to avoid

having liquids seep into the internal components and areas
of the medical panel PC unit.

Error message / Troubleshooting

Servicing, Repairing, Maintenance & Safety Checks

1. If the unit is not functioning properly, observe the

performance level of the display closely to determine what
type of servicing is needed.

WMP-19B/22B User’s manual

ix

ISO 7000-0434: Caution.

ISO 7000-1641: Follow operating instructions or
Consult instructions for use.

IEC 60417 -5009: STAND-BY.
IEC 60417-5031: Direct current.

2. Do not attempt to repair the medical panel PC unit on your

own. Disassembling the cover exposes users’ to high

voltages and other dangerous conditions. Notify and
request a qualified service technician for servicing the unit.

3. To avoid risk of electric shock, this equipment must only be

connected to a supply mains with protective earth.

4. If any of the following situations occur turn the power

source off and unplug the unit. Then contact a qualified
service technician.

(a) A liquid was spilled on the unit or objects have fallen

into the unit.

(b) The unit is soaked with liquids.
(c) The unit is dropped or damaged.
(d) If smoke or strange odor is flowing out of the operating

unit.

(e) If the power cord or plug is damaged.
(f) When the functions of the unit are dysfunctional.

5. When replacement parts are needed for the medical panel

PC unit, make sure service technicians use replacement
parts specified by the manufacturer, or those with the
same characteristics and performance as the original
parts. If unauthorized parts are used it may result in
starting a fire, electrical shock and/or other dangers.

WMP-19B/22B User’s manual

x

EU-wide legislation, as implemented in each
Member State, requires that waste electrical and
electronic products carrying the mark (left) must be
disposed of separately from normal household
waste. This includes monitors and electrical
accessories, such as signal cables or power cords.
When you need to dispose of your display products,
please follow the guidance of your local authority, or
ask the shop where you purchased the product, or if
applicable, follow any agreements made between
yourself.

The mark on electrical and electronic products only
applies to the current European Union Member

States.

WMP-19B/22B User’s manual

xi

When networking with electrical devices, the operator is
responsible for ensuring that the resulting system meets the
requirements set forth by the following standards:

– EN 60601-1 (IEC 60601-1)

Medical electrical equipment
Part 1: General requirements for safety

– EN 60601-1-1 (IEC 60601-1-1)

Medical electrical equipment
Part 1-1: General requirements for safety
Collateral standard: Safety requirements for
Medical electrical systems

– EN 60601-1-2 (IEC 60601-1-2)

Medical electrical equipment
Part 1-2: General requirements for safety
Collateral standard: Electromagnetic compatibility;
Requirements and tests

Accessory
equipment
connected to
the analog
and digital
interfaces
must be in
compliance with the respective nationally harmonized IEC
standards (i.e. IEC 60950 for data processing equipment, IEC
60065 for video equipment, IEC 61010-1 for laboratory
equipment, and IEC 60601-1 for medical equipment.)
Furthermore all configurations shall comply with the system
standard IEC 60601-1-1. Everybody who connects additional
equipment to the signal input part or signal output part
configures a medical system, and is therefore, responsible that
the system complies with the requirements of the system
standard IEC 60601-1-1. The unit is for exclusive interconnection
with IEC 60601-1 certified equipment in the patient environment
and IEC 60XXX certified equipment outside of the patient
environment. If in doubt, consult the technical services
department or your local representative.

WMP-19B/22B User’s manual

xii

Caution:

DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW

-20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE
EQUIPMENT.

This equipment shall not be used in life support systems.

The user is not to touch SIP/SOPs and the patient at the same
time.

Caution – Use suitable mounting apparatus to avoid risk of injury.

Caution - Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the instructions.

The sound pressure level at the operator’s position according to

IEC 704-1:1982 is no more than 70dB (A).

A) Grounding reliability can only be achieved when the equipment

is connected to an equivalent receptacle marked “Hospital
Only” or “Hospital Grade”.

B) Use a power cord that matches the voltage of the power outlet,

which has been approved and complies with the safety
standard of your particular country.

C) Caution: This adapter Sinpro HPU180A-108 is a forming part of

the medical device

Contact information:

Wincomm Corporation
3F, No.14, Prosperity Road II, Science-Based Industrial Park,
Hsinchu, Taiwan 300, R.O.C
TEL: [phone]

E-Mail: [e-mail]

WMP-19B/22B User’s manual

xiii

Table of Contents

Acknowledgments ...................................... iii

FCC Class B ............................................... iv

Safety Instructions ...................................... v

Introduction ............................................ 1

Product Description .................................... 1

Package list ............................................... 2

Features ................................................... 3

Specifications ............................................ 4

Guidance and manufacturer’s declaration –

electromagnetic emissions ...................... 7

Guidance and manufacturer’s declaration –

electromagnetic immunity ...................... 8

Immunity .................................................. 9

Cleaning/Disinfecting ................................. 11

Getting Started ..................................... 12

System Set Up .......................................... 12

Dimension ................................................ 13

System View............................................. 15

Disconnect Device ..................................... 18

BIOS Setup ........................................... 19

Appendix ............................................... 31

A. Jumper settings and Connectors .............. 31

B. Battery Pack Specifications (optional kit) .. 50
C. How to disable battery when system hang up

-WMP-19B/22B ......................................... 51

D. Scrap Computer Recycling ...................... 52

WMP-19B/22B User’s manual

1

Introduction

Product Description

The WMP-19B/22B Medical Panel PC is based on Intel 5th
generation Core i mobile CPU (H series) processor, it

accommodates one 2.5” SATA III hard disk drive and up to 16GB
DDR3L SODIMM.

The high brightness LCD, smart fan solution, integrated
multimedia functions and extensive expansion options make
them the perfect platform upon which to build comprehensive
lifestyle computing applications.

The WMP-19B/22B includes all the features of a powerful
computer into a slim and attractive chassis. WMP-22B has a
250nits 21.5” TFT display with 1920 x 1080 resolutions.
WMP-19B has a 19” 350nits TFT display with 1280 x 1024

resolutions. Integrating with high brightness LCD is easier to analyze
DICOM image.

The WMP-19B/22B is compact, two Giga LAN and selectable
WLAN network compatible PC with full safety and medical
approval and features to control a dedicated system with a wide
variety of applications. Combining the WMP-19B/22B into your
system can achieve both cost-saving and efficient improvements.

Common applications include LIS (Lab Information Systems) and
Electronic Medical Record. The WMP-19B/22B are definitely your
perfect choices.

WMP-19B/22B User’s manual

2

Package list

Before you begin installing your Medical Station, please make
sure that the following items have been shipped:

 The WMP-19B/22B Medical Panel PC unit
 User's manual, chipset drivers
 Power Adapter x 1 (Mf:Sinpro, type/model: HPU180A-108)
 Power cord – Hospital grade used (US type), or other type in

UK, EU…etc.

 Screw x 8 (VESA 75/100 use)

WMP-19B/22B User’s manual

3

Features



 Anti-bacteria (MRSA) plastic housing
 21.5" full HD (1920X1080) / 19” (1280x1024) Panel
 High performance 4
 Supports Dual Channel DDR3L SODIMM up to 16GB
 P.cap Multi-Touch Screen
 Easy wipe surfaces with no internal corners
 IP65 at front side
 Smart Fan solution
 Two mini PCI-e expansion (One full size and one half size)
 HDD Anti-vibration mechanism
 Supports PCI-E x16 riser card (option)
 Easy clean full flat 5 wire resistive touch screen (customized

order configuration)

th/5th

generation intel Core i mobile CPU

 USB/LAN/COM isolated module by different configuration

(optional order configuration)

 Optional 28W battery pack, desktop stand
 DICOM Compliance (project customized)

WMP-19B/22B User’s manual

4

Display

21,5” 250 nits 1920x1080 TFT LCD
19” 350 nits 1280x1024 TFT LCD

CPU Support

FCBGA1364 4th/5th generation Intel® Core

i7/i5 processor (47W max.)

Disk Drive Space

2.5” Hard Disk Drive (SATA III)

Expansion

One PCI-E x 16 expansion slot (+3.3V loaded 3A,
total loaded 9.9W)

Button

Power Button// Audio adjustment (+)(-) //
brightness (+)(-) // LCD on/off // Clean me(auto
release after 1 minute)

I/O

Standard version

PCI-E x 16 slot *1(optional riser card)
RS-232 port *1 + RS-232/422/485 port *1
USB 3.0 port *4
DC-in w/ lock function *1
Gigabit LAN RJ-45 Connectors *2
DP output *2
Sound:
Line-in *1
Line-out *1
2W Speaker *2 (WMP-19B) / 1.5W Speaker *2
(WMP-22B)

Isolated version

Isolated 4KV USB2.0 *1
Isolated 4KV GigaLAN *1
Isolated 4KV RS-232 *1, RS-232/422/485 *1
(The isolated ports verified through Dielectric test
4000Vac only)
RS-232 port *1 + RS-232/422/485 port *1
USB 3.0 port *4
DC-in w/ lock function *1
Gigabit LAN RJ-45 Connectors *2
DP output *2
Sound:
Line-in *1
Line-out *1
2W Speaker *2 (WMP-19B) / 1.5W Speaker *2
(WMP-22B)

Specifications

[

Hardware Specifications

WMP-19B/22B User’s manual

5

Model Name

WMP-22B

WMP-19B

Display Type

21.5” LED

19” LED

Max. Resolution

1920 x 1080

1280 x 1024

Contrast Ratio

1000 : 1 (Typ)

1000 : 1 (Typ)

Pixel Pitch (um)

248.25 × 248.25

294 x 294

Luminance
(cd/m2)

250 (TYP)

350 (TYP)

Viewing Angle

170°(H)

170°(H)

160°(V)

160°(V)

Power

Close-frame

MFR

Sinpro

Type

HPU180A-108

Input Rating

AC 100 ~ 240 V, 1.2 – 0.5A @ 47 ~ 63 Hz

Output Rating

DC 24V, 7.5A

MTBF

100,000 hrs operation at 25°C

Classification

Power by Class I certified power adapter.
No applied part.

Mode of operation

Continuous operation

System input rating

DC 24V, 7A

Architecture

Close-frame

Front Bezel

PCT touch screen / PET bezel with resistive
touch screen

Color

Medical-white

Mounting / Holder

VESA 75/100mm

Construction

3mm ABS + PC TYPE Plastic housing

Dimension (WxHxD)

WMP-22B: 540 x 375 x 78 mm
WMP-19B: 450 x 420 x 85.3 mm

Net Weight

WMP-22B: 8.0 kg (w/o power adapter)

WMP-19B: 7.5 kg (w/o power adapter)

Packing Filler

PE

LCD Specifications

Cautions:

Continuous displaying fixed pattern may induce image sticking.

It’s recommended to use screen saver or moving content
periodically if fixed pattern is displayed on the screen.

Power Adapter Specifications

Mechanical Specifications

WMP-19B/22B User’s manual

6

Temperature

Operating: 0°C to 40°C (32°F ~104°F)
Storage, Transportation: -20°C to 60°C (-4°F
~140°F)

Humidity

Operating:
10% to 90%@ 40°C, non-condensing
Storage, Transportation:
10% to 90%, non-condensing

Vibration

Operating: 15g/0.53 oz, 11 ms, half sine wave
Non-operating: 50g/1.76 oz, 11 ms, half sine
wave

Shock

Operating: 5 ~ 17 Hz ,
Amplitude：0.117 ~ 500Hz ,

Acceleration：1.0G
Non-operating:10~55Hz/0.15g, 55~500Hz/2.0g

Altitudes

Operational: up to 3000 m (9842 feet)
Shipping: up to 12192 m (40000 feet)

Pressure

700 – 1060 hPa (Operation)
186 – 1060 hPa (Storage)
186 – 1060 hPa (Transportation)

EMI / Safety

CE / FCC / VCCI Class B/UL 60601-1/EN 60601-1

IP

Front bezel, IP-65 Certified

Noise

Under 30db (at 25°C)

Type

Full flat projective capacitive touch panel

Interface

Controller with USB interface, 5V

Resolution

100ppi to 25ppi Based WIN7 definition ppi
(Pixel per inch)

Light Transmission

90% ± 3%

Life Time

100M times

Type

Full flat 5-wire, Analog Resistive

Interface

USB interface, 5V

Resolution

4096 x 4096

Light Transmission

>78% at 550 nm wavelength

Life Time

35M times, 250g at same place

Environmental Specifications

Touch Screen
Configuration 1 - P.cap touch

Configuration 2 - 5 wire Resistive touch

WMP-19B/22B User’s manual

7

Guidance and manufacturer’s declaration – electromagnetic
emissions

The model WMP-19B/22B is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
WMP-19B/22B should assure that it is used in such an environment.

Emissions test

Compliance

Electromagnetic environment –

guidance

RF emissions
CISPR 11

The model WMP-19B/22B uses RF
energy only for its internal function.
Therefore, its RF emissions are very
low and are not likely to cause any
interference in nearby electronic
equipment.

RF emissions
CISPR 11

The model WMP-19B/22B is suitable
for use in all establishments,
including domestic establishments
and those directly connected to the
public low-voltage power supply
network that supplies buildings used
for domestic purposes.
Harmonic
emissions

IEC 61000-3-2

Voltage
fluctuations/

flicker emissions
IEC 61000-3-3

Recommended separation distances between

portable and mobile RF communications equipment and the model

WMP-19B/22B

The model WMP-19B/22B is intended for use in an electromagnetic
environment in which radiated RF disturbances are controlled. The
customer or the user of the model WMP-19B/22B can help prevent
electromagnetic interference by maintaining a minimum distance
between portable and mobile RF communications equipment
(transmitters) and the model WMP-19B/22B as recommended below,
according to the maximum output power of the communications
equipment.

Rated maximum
output power of

transmitter

W

Separation distance according to

frequency of transmitter

m

150 kHz to

80 MHz

d = 1,2

80 MHz to

800 MHz

d = 1,2

800 MHz to

2,5 GHz

d = 2,3

0,01

0,12

0,12

0,23

WMP-19B/22B User’s manual

8

0,1

0,38

0,38

0,73 1 1,2

1,2

2,3

10

3,8

3,8

7,3

100

12

12

23

For transmitters rated at a maximum output power not listed above, the
recommended separation distanced in meters (m) can be estimated
using the equation applicable to the frequency of the transmitter, where P
is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher
frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures,
objects and people.

Guidance and manufacturer’s declaration – electromagnetic
immunity

The model WMP-19B/22B is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
WMP-19B/22B should assure that it is used in such an environment.

Immunity test

IEC 60601

test level

Compliance

level

Electromagnetic

environment –

guidance

Electrostatic
discharge
(ESD)

IEC 61000-4-2

6 kV contact

8 kV air

6 kV contact

8 kV air

Floors should be
wood, concrete or
ceramic tile. If floors
are covered with
synthetic material, the
relative humidity
should be at least 30
%.

Electrical fast
transient/burst

IEC 61000-4-4

2 kV for
power

supply lines

1 kV for
input/output

lines

2 kV for
power

supply lines

1 kV for
input/output

lines

Mains power quality
should be that of a
typical commercial or
hospital environment.

WMP-19B/22B User’s manual

9

Surge
IEC 61000-4-5

1 kV line(s)
to line(s)

2 kV line(s)
to earth

1 kV line(s)
to line(s)

2 kV line(s)
to earth

Mains power quality
should be that of a
typical commercial or
hospital environment.

interruptions
and

voltage
variations

on power
supply

input lines

IEC
61000-4-11

<5 % UT
(>95 % dip in

UT)
for 0,5 cycle

40 % UT
(60 % dip in

UT)
for 5 cycles

70 % UT
(30 % dip in

UT)
for 25 cycles

<5 % UT
(>95 % dip in

UT)
for 5 sec

<5 % UT
(>95 % dip in

UT)
for 0,5 cycle

40 % UT
(60 % dip in

UT)
for 5 cycles

70 % UT
(30 % dip in

UT)
for 25 cycles

<5 % UT
(>95 % dip in

UT)
for 5 sec

Mains power quality
should be that of a
typical commercial or
hospital environment.
If the user of the
model
WMP-19B/22B
requires continued
operation during
power

mains interruptions, it
is recommended that
the model
WMP-19B/22B be
powered from an
uninterruptible power
supply or a battery.

Power
frequency

(50/60 Hz)
magnetic field

IEC 61000-4-8

3 A/m

3 A/m

Power frequency
magnetic fields
should be at levels
characteristic of a
typical location in a
typical commercial or
hospital environment.

NOTE UT is the a.c. mains voltage prior to application of the test level.

Guidance and manufacturer’s declaration – electromagnetic immunity

The model WMP-19B/22B is intended for use in the electromagnetic environment specified below. The
customer or the user of the model WMP-19B/22B should assure that it is used in such an environment.

Immunity

IEC

60601

test level

Compliance

level

Electromagnetic environment – guidance

WMP-19B/22B User’s manual

10

Conducted RF
IEC 61000-4-6

Radiated RF
IEC 61000-4-3

3 Vrms
150 kHz

to 80
MHz

3 V/m
80 MHz

to 2,5
GHz

Vrms

V/m

Portable and mobile RF communications
equipment should be used no closer to any part
of the model WMP-19B/22B, including cables,
than the recommended separation distance
calculated from the equation applicable to the
frequency of the transmitter.

Recommended separation distance

d = 1,2

d = 1,2 80 MHz to 800 MHz
d = 2,3 800 MHz to 2,5 GHz

where P is the maximum output power rating of
the transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in meters
(m).

Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey, a
should be less than the compliance level in
each frequency range. b

Interference may occur in the vicinity of
equipment marked with the following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption
and reflection from structures, objects and people.

a

Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones

and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be
predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field strength in
the location in which the model WMP-19B/22B is used exceeds the applicable RF compliance level
above, the model WMP-19B/22B should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as reorienting or relocating
the model WMP-19B/22B.

b

Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

WMP-19B/22B User’s manual

11

Cleaning/Disinfecting



Steps:

1. Wipe the WMP-19B/22B with a dry clean cloth.

2. Operate with manufacturer’s instructions or hospital protocol.



Cautions:

 Do not immerse or rinse the WMP-19B/22B and its

peripherals. If you accidentally spill liquid on the device,
disconnect the unit from the power source. Contact your
Biomed regarding the continued safety of the unit before
placing it back in operation.

 Do not spray cleaning agent on the chassis.
 Do not use disinfectants that contain phenol.
 Do not autoclave or clean the WMP-19B/22B or its

peripherals with strong aromatic, chlorinated, ketone, ether,
or Esther solvents, sharp tools or abrasives. Never immerse
electrical connectors in water or other liquids.

WMP-19B/22B User’s manual

12

Caution:

In order to boot up system from USB-CD/DVD drive,
please connect USB-CD/DVD drive, turn on computer

power, keep on pressing “F11” key, go into BIOS quick
boot menu, select “USB-CD ROM”, WAIT FOR 20

SECONDS, then press enter, system OS will boot up
from USB-CD/DVD drive directly.

Notice:

The installation is only to be carried out by
manufacturer trained and authorized personnel.

Getting Started

System Set Up

The following is a summary of the steps in setting up the system
for use.
(1). You can fix the system to a mounting fixture using the screw

holes on the sides of the system.

(2). Make any required external connections such as the display,

keyboard, and LAN.

(3). Plug the appropriate end of the power cord into the power

connector on the rear of the system and the plug to an
electrical outlet.

(4). Waiting for 3 seconds then press the power switch on the

front panel of the system once to turn on the system power.

(5). If necessary, run the BIOS SETUP programs to configure the

system.

WMP-19B/22B User’s manual

13

Dimension

WMP-22B

(VESA Mount Screw type: M4)

WMP-19B/22B User’s manual

14

WMP-19B

(VESA Mount Screw type: M4)

WMP-19B/22B User’s manual

15

Webcam (optional)

System View



Front View

Hotkey and LED definition at front panel

Located on Touch screen bottom side, from left to right, front view
1-1. Up. HDD: Amber
1-2 Down. Battery:

AC mode: Dark
Battery mode: Yellow
Battery low: Yellow blinking

2. Power (with LED status indicator: ON: Green, OFF: dark)

3. Volume adjustment (-)

4. Volume adjustment (+)

5. Brightness (-)

6. Brightness (+)

7. LCD on/off (with LED status indicator: LCD ON: dark, LCD OFF:

WMP-19B/22B User’s manual

16

Amber)

8. Clean me (with LED status indicator: ON: Yellow, OFF: dark) /
DICOM switch (w/ DICOM mode)

a. Keep on contacting 5 seconds to active
b. keep contacting 5 seconds to release
c. auto release after 60 seconds
d. keep on contacting below for 5 seconds to toggle DICOM

mode enabled/disable if DICOM module presents

I/O parts (WMP-19B/22B)

WMP-19B/22B User’s manual

17

Isolated I/O parts (WMP-19B/22B)

WMP-19B/22B User’s manual

18

Unplug the power cord from the power
adapter jack to disconnect the device.

Disconnect Device 

Turn off the system:

Turning off WMP-19B/22B properly is important for system
reliability.

1. On the start menu, click “Shut down” and select “OK”

WMP-19B/22B User’s manual

19

BIOS Setup

BIOS Introduction

The AMI BIOS (Basic Input / Output System) installed in your

computer system’s ROM supports Intel processors. The BIOS

provides critical low-level support for a standard device such as
disk drives, serial ports and parallel ports. It also adds virus and
password protection as well as special support for detailed
fine-tuning of the chipset controlling the entire system.

BIOS Setup

The AMI BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system
stores the Setup utility. When you turn on the computer, the AMI
BIOS is immediately activated. Pressing the <Del> key
immediately allows you to enter the Setup utility. If you are a
little bit late pressing the <Del> key, POST (Power On Self Test)
will continue with its test routines, thus preventing you from
invoking the Setup. If you still wish to enter Setup, restart the

system by pressing the ”Reset” button or simultaneously pressing

the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message
will appear on the screen:

Press <DEL> to Enter Setup

In general, you press the arrow keys to highlight items, <Enter>
to select, the <PgUp> and <PgDn> keys to change entries, <F1>
for help and <Esc> to quit.

When you enter the Setup utility, the Main Menu screen will
appear on the screen. The Main Menu allows you to select from
various setup functions and exit choices.

WMP-19B/22B User’s manual

20

Main

This section provides information on the BIOS information, and Battery information

System Date
Set the system date. Use the <Tab> key to switch between data
elements.

System Time
Set the system time. Use the <Tab> key to switch between time
elements.

WMP-19B/22B User’s manual

21

Advanced

Trusted Computing

Configuration

Enables or disables BIOS support for security device. O.S. will
not show Security Device. TCG EFI protocol and INT1A interface
will not be available.

ACPI Settings

Enable Hibernation

Enables or Disables System ability to Hibernate (0S/S4
Sleep State). This option may be not effective with some OS.

ACPI Sleep State

Select the highest ACPI sleep state the system will enter
when the SISPEND button is pressed.

F81216 Super IO Configuration

Serial Port 1 Configuration
Serial Port
Enable or Disable Serial Port (COM).

Function

WMP-19B/22B User’s manual

22

RS232,RS422,RS485
Change Settings
Select an optimal settings for super IO Device.
Change Settings
Select an optimal settings for Super IO Device.

Set Parameters of Serial Port 1.

Serial Port 2 Configuration
Serial Port
Enable or Disable Serial Port (COM).

Change Settings

Select an optimal settings for super IO Device.

Serial Port 3 Configuration
Serial Port
Enable or Disable Serial Port (COM).

Change Settings

Select an optimal settings for super IO Device.

Serial Port 4 Configuration
Serial Port
Enable or Disable Serial Port (COM).

Serial Port 5 Configuration
Serial Port
Enable or Disable Serial Port (COM).

Serial Port 6 Configuration
Serial Port
Enable or Disable Serial Port (COM).

Change Settings

Select an optimal settings for super IO Device.

Intel(R) Smart Connect Technology

ISCT Support

Enable/Disable Intel Smart Connect

S5 RTC Wake Settings

Wake system From S5

WMP-19B/22B User’s manual

23

Enable or disable System wake on alarm event. Select
FixedTime, System will wake on the hr::min::sec specified.
Select DynamicTime , System will wake on the current time
+ Increase minute(s).

CPU Configuration

Socket 0 CPU Information

Socket specific CPU Information.

IDE Configuration

Serial-ATA (SATA)

Enable / disable Serial ATA.

SATA Test Mode

Test Mode enable / disable.

SATA Speed Support

SATA Speed Support Gen1 or Gen2.

SATA ODD Port

SATA ODD is Port0 or Port1.

SATA Mode

Select IDE / AHCI

Serial-ATA Port 0

Enable / Disable Serial ATA Port 0.

SATA Port0 HotPlug

Enable / Disable SATA Port0 HotPlug.

Serial-ATA Port 1

Enable / Disable Serial ATA Port 1.

SATA Port0 HotPlug

Enable / Disable SATA Port1 HotPlug

Embedded Controller Configuration

Lock key click time

Number of seconds to press lock key to (un)active.
1~10 seconds mean press hold time.

Locked Status Hold Time

WMP-19B/22B User’s manual

24

Number of minutes to keep lock status. 0 means lock always.
1~100 minutes mean lock hold time.

Power key
Enable / Disable power key.

Mute key
Enable / Disable Mute key.

Volume Up/Dn keys
Enable / Disable Vol+/Vol- key.

LCD Brightness Up/Dn keys
Enable / Disable LCD Brightness up/down key.

LCD Backlight On / Off key
Enable / Disable LCD Backlight key.

Lock key
Enable / Disable Lock key.

Webcam key
Enable / Disable webcam key.

Fn key

Enable/Disable Function key

Miscellaneous Configuration

PCI Express Dynamic Clock Gating

Enable / Disable PCIE Dynamic Clock Gating.

Show/hide hidden items

For debug only.
Show / hide hidden items.

Info Report Configuration

Post Report

Post Repost Support Enabled / Disabled.

Info Error Message

Info Error Message Support Enabled / Disabled.

WMP-19B/22B User’s manual

25

Summary Screen

Summary Screen Support Enabled / Disabled.

USB Configuration

USB Support

USB Support Parameters.

Legacy USB Support

Enables Legacy USB support. AUTO option disables legacy
support if no USB devices are connected. DISABLE option will
keep USB devices available only for EFI applications

XHCI Hand-off

Enable / Disable XHCI Controller Legacy support.

USB Mass Storage Driver Support

Enable/Disable USB Mass Storage Driver Support.

WMP-19B/22B User’s manual

26

Chipset

North Bridge
Config Intel IGD Settings.
South Bridge

High Precision Timer

Enable or Disable the High Precision Event Timer.

Audio Controller

Control Detection of the Azalia device.
Disabled = Azalia will be unconditionally disabled.
Enable = Azalia will be unconditionally Enabled.
Auto = Azalia will be enabled if present disabled otherwise.

Restore AC Power Loss
Select AC power state when power is re-applied after a power
failure.

WMP-19B/22B User’s manual

27

Security

Administrator Password

Set Administrator Password.

User Password

Set user Password.

P0：TOSHIBA MQ01
HDD Security Configuration for selected drive.

WMP-19B/22B User’s manual

28

Boot

Setup Prompt Timeout

Number of seconds to wait for setup activation key.

65535(0xFFFF) means indefinite waiting.
Bootup Numlock State

Selects the keyboard NumLock state.
PXE Boot

PXE Network Boot Enable / Disable.
OS Selection

OS Selection.
Quiet Boot

Enable or disables Quiet Boot option.
Boot Option #1

Sets the system boot order.
Boot Option #2

Sets the system boot order.

WMP-19B/22B User’s manual

29

Save & Exit

Save Changes and Exit

Exit system setup after saving the changes.

Discard Changes and Exit

Exit system setup without saving any changes.

Save Changes and Reset

Reset the system after saving the changes.

Discard Changes and Reset

Reset system setup without saving the changes.

Save Changes

Save the changes done so far to any of setup options.

Discard Changes

Discard the changes done so far to any of setup options.

Restore Defaults

Restore/load default values for all the setup options.

WMP-19B/22B User’s manual

30

Save as User Defaults

Save the changes done so far as User Defaults.

Restore User Defaults

Restore the User Defaults to all the setup options.

Boot Override

To override the boot device.

Launch EFI Shell From filesystem device
Attempts to Launch EFI Shell application (Shell.efi) from one of
the available filesystem devices.

Reset System with ME disable ModeMEUD000
ME will runs into the temporary disable mode, Ignore if ME
Ignition FWMEUD001.

WMP-19B/22B User’s manual

APPENDIX

31

Appendix

A. Jumper settings and Connectors

This appendix gives the definitions and shows the positions of
jumpers, headers and connectors. All of the configuration
jumpers on WMP-19B/22B are in the proper position.

Note: Some of jumpers or connectors will be removed
base on system configuration.

Jumper and Connector Definition Block

WMP-19B/22B User’s manual

APPENDIX

32

Description

Jumper Setting

Analog Inverter

1-2

PWM Inverter

2-3

Description

Jumper Setting

X+/UL_R

1-2 (default)

Y+/UR_R

3-4 (default)

X+/UL_R

5-6

Y+/UR_R

7-8

SWITCH_4_5W

9-10

GPIO0

GPIO1

GPIO2

GPIO3

Description

Jumper Setting

1 0 0 0 1024X768(6bit)

0 1 0 0

1024X768(8bit)

0 0 1 0

1280X800(8bit)

0 1 1 0

1280X1024(8bit)

0 1 1

1

1920X1080(8bit)

GPIO0 Low
(default)

 JP1 – Backlight Type Selection

 JP2 – Touch Panel Type Selection

 JP3 – Panel Resolution Settings

WMP-19B/22B User’s manual

33

 JP4 – LVDS Power Settings

Description

Jumper Setting

+5VS

1-2 (default)

+5VS

3-4 (default)

+3.3VS

5-6

+3.3VS

7-8

Description

Jumper Setting

Normal Open

1-2 (default)

CMOS Clear

2-3

Description

Jumper Setting

mSATA_SEL43

2-3

mSATA_SEL51

1-2

Description

Jumper Setting

SATA DOM

1-2 ---power +5V

SATA Port

2-3(default)--- GND

 JP6 – CMOS clear

APPENDIX

 JP7 – mSATA setting

 JP8 – SATA or SATA DOM Selection

WMP-19B/22B User’s manual

APPENDIX

34

Pin #

Signal Description

1

+12VS

2

Ground

3

Ground

4

+5VS

Pin #

Signal Description

1

BATT+

2

BATT+

3

BATT+

4

BATT_T

5

BATT_CLK

6

BATT_DAT

7

BATT_EN#

8

Ground

9

Ground

10

Ground

Connector Definition

PJ1 /PJ2 – HDD Power Connector

PJ3 – Battery Connector

PJ4 – Power Jack Connector

WMP-19B/22B User’s manual

35

Pin #

Signal Description

1

DC In

2

DC In

3

Ground

4

Ground

5

Ground

Pin #

Signal Description

1

+5VSB

2

+5VSB

3

Data -

4

Data +

5

Ground

6

Ground

Pin

Symbol

Pin

Symbol

Pin

Symbol

Pin

Symbol

Pin

Symbol

Pin

Symbol

1

VREFDQ

69

DQ27

137

DQS4

2

VSS

70

DQ31

138

VSS 3 VSS

71

VSS

139

VSS 4 DQ4

72

VSS

140

DQ38

5

DQ0

73

CKE0

141

DQ34

6

DQ5

74

NC

142

DQ39

7

DQ1

75

VDD

143

DQ35

8

VSS

76

VDD

144

VSS 9 VSS

77

NC

145

VSS

10

DQS0#

78

NC

146

DQ44

11

DM0

79

BA2

147

DQ40

12

DQS0

80

NF/A14

148

DQ45

13

VSS

81

VDD

149

DQ41

14

VSS

82

VDD

150

VSS

15

DQ2

83

A12

151

VSS

16

DQ6

84

A11

152

DQS5#

17

DQ3

85

A9

153

DM5

18

DQ7

86

A7

154

DQS5

19

VSS

87

VDD

155

VSS

20

VSS

88

VDD

156

VSS

21

DQ8

89

A8

157

DQ42

22

DQ12

90

A6

158

DQ46

23

DQ9

91

A5

159

DQ43

24

DQ13

92

A4

160

DQ47

25

VSS

93

VDD

161

VSS

26

VSS

94

VDD

162

VSS

27

DQS1#

95

A3

163

DQ48

28

DM1

96

A2

164

DQ52

29

DQS1

97

A1

165

DQ49

30

RESET#

98

A0

166

DQ53

J1/J2/J3/J11/J12/J13 – Internal USB Pin Header

Pin1

APPENDIX

J3 / J11 – DDR3 SO-DIMM Interface

J3 H9.2 STD
J11 H9.2 REV

WMP-19B/22B User’s manual

APPENDIX

36

31

VSS

99

VDD

167

VSS

32

VSS

100

VDD

168

VSS

33

DQ10

101

CK0

169

DQS6#

34

DQ14

102

CK1

170

DM6

35

DQ11

103

CK0#

171

DQS6

36

DQ15

104

CK1#

172

VSS

37

VSS

105

VDD

173

VSS

38

VSS

106

VDD

174

DQ54

39

DQ16

107

A10

175

DQ50

40

DQ20

108

BA1

176

DQ55

41

DQ17

109

BA0

177

DQ51

42

DQ21

110

RAS#

178

VSS

43

VSS

111

VDD

179

VSS

44

VSS

112

VDD

180

DQ60

45

DQS2#

113

WE#

181

DQ56

46

DM2

114

S0#

182

DQ61

47

DQS2

115

CAS#

183

DQ57

48

VSS

116

ODT0

184

VSS

49

VSS

117

VDD

185

VSS

50

DQ22

118

VDD

186

DQS7#

51

DQ18

119

A13

187

DM7

52

DQ23

120

NC

188

DQS7

53

DQ19

121

NC

189

VSS

54

VSS

122

NC

190

VSS

55

VSS

123

VDD

191

DQ58

56

DQ28

124

VDD

192

DQ62

57

DQ24

125

NC

193

DQ59

58

DQ29

126

VREFCA

194

DQ63

59

DQ25

127

VSS

195

VSS

60

VSS

128

VSS

196

VSS

61

VSS

129

DQ32

197

SA0

62

DQ3#

130

DQ36

198

EVENT#

63

DM3

131

DQ33

199

VDDSP
D

64

DQ3

132

DQ37

200

SDA
65

VSS

133

VSS

201

SA1

66

VSS

134

VSS

202

SCL

67

DQ26

135

DQS4#

203

VTT

68

DQ30

136

DM4

204

VTT

Pin #

Signal Description

Pin #

Signal Description

1

+LCD (+5V/ +3.3V)

2

+LCD (+5V/ +3.3V)

3

+LCD (+5V/ +3.3V)

4

+LCD (+5V/ +3.3V)

5

Ground

6

Ground

7

Ground

8

Ground

9

A_RxIn0-

10

B_RxIn0-

11

A_RxIn0+

12

B_RxIn0+

13

Ground

14

Ground

15

A_RxIn1-

16

B_RxIn1-

17

A_RxIn1+

18

B_RxIn1+

19

Ground

20

Ground

21

A_RxIn2-

22

B_RxIn2-

23

A_RxIn2+

24

B_RxIn2+

25

Ground

26

Ground

27

A_CKIN-

28

B_CKIN-

29

A_CKIN+

30

B_CKIN+

31

Ground

32

Ground

J4 – LVDS Interface

WMP-19B/22B User’s manual

37

33

A_RxIn3-

34

B_RxIn3-

35

A_RxIn3+

36

B_RxIn3+

37

Ground

38

Ground

39

Ground

40

Ground

1

9

Pin #

Signal Description

8-wire

4-wire

5-wire

1

UL(X+)

UL(X+)

UL(X+)

2

UR(Y+)

UR(Y+)

UR(Y+)

3

N/A

N/A

PROBE

4

LR(X-)

LR(X-)

LR(X-)

5

LL(Y-)

LL(Y-)

LL(Y-)

6

X+_DRIVE

N/A

N/A

7

Y+_DRIVE

N/A

N/A

8

X-_DRIVE

N/A

N/A

9

Y-_DRIVE

N/A

N/A

J5 – Res Touch Panel Interface

APPENDIX

J6 / J12 – Mini PCI Express Socket

WMP-19B/22B User’s manual

APPENDIX

38

Pin #

Signal Description

Pin #

Signal Description

1

CS# 5 SI

2

SO 6 SCLK

3

WP#

7

HOLD#

4

VSS

8

VDD

Pin #

Signal Description

Pin #

Signal Description

1

WAKE#

2

+3.3VSB

3

Reserved

4

GND 5 Reserved

6

+1.5VS

7

CLKREQ#

8

Reserved

9

GND

10

Reserved

11

REFCLK-

12

Reserved

13

REFCLK+

14

Reserved

15

GND

16

Reserved

17

Reserved

18

GND

19

Reserved

20

Reserved

21

GND

22

PERST#

23

PERn0

24

+3.3VSB

25

PERp0

26

GND

27

GND

28

+1.5VS

29

GND

30

SMB_CLK

31

PETn0

32

SMB_DATA

33

PETp0

34

GND

35

GND

36

USB_D-

37

GND

38

USB_D+

39

+3.3VSB

40

GND

41

+3.3VSB

42

Reserved

43

GND

44

Reserved

45

CL_CLK

46

Reserved

47

CL_ DATA

48

+1.5VS

49

Controller Link RST#

50

GND

51

Reserved

52

+3.3VSB

J7 – BIOS Socket

WMP-19B/22B User’s manual

39

J8 – PCT Touch

Pin #

Signal Description

1

+5VSB

2

+5VSB

3

Data -

4

Data +

5

Ground

6

Ground

Pin #

Signal Description

1

+5VSB

2

+5VSB

3

Data -

4

Data +

5

Ground

6

Ground

APPENDIX

J9/J14/J15 – Internal USB 2.0 Pin Header (co-layout)

Pin1

J16– Power / HDD LED

WMP-19B/22B User’s manual

APPENDIX

40

Pin #

Signal Description

1

SATA_LED#

2

+3.3VSB

3

+3.3VSB

4

PWR_LED#

Pin #

Signal Description

Pin #

Signal Description

1

TRST#

2

+3.3VSB

3

TMS

4

RDY#

5

TDI 6 GND

7

TCK

8

GND

9

TDO

10

GND

Pin #

Signal Description

Pin #

Signal Description

1

LPC AD0

2

PLT reset#

3

LPC AD1

4

SERIRQ

5

LPC AD2

6

+3.3VS

7

LPC AD3

8

+5VSB

9

LPC Frame#

10

CLKRUN#

11

Debug CLK

12

SMB CLK

13

GND

14

SMB DATA

15

SUS_STAT#

16

+3.3VSB

J17 – For JTAG

J18 –TPM / ID-394

WMP-19B/22B User’s manual

41

Pin #

Signal Description

1

Ground

2

Tx+ 3 Tx-

4

Ground

5

Rx- 6 Rx+ 7 Ground

Pin #

Signal Description

1

KBDATA

2

MSDATA

3

Ground

4

+5VSB

5

KBCLK

6

MSCLK

J19 / J21 – Standard SATA Interface

APPENDIX

J23 – PS2 KB/MS

WMP-19B/22B User’s manual

APPENDIX

42

Pin #

Signal Description

1

EC_RESET#

2

GND

Pin #

Signal Description

1

RTC +3.3V

2

GND

Pin #

Signal Description

Pin #

Signal Description

1

GEN_GPO1

2

GEN_GPI1

3

GEN_GPO2

4

GEN_GPI2

5

GEN_GPO3

6

GEN_GPI3

7

GEN_GPO4

8

GEN_GPI4

9

+5V

10

+5V

11

GND

12

GND

J24 – EC Reset

J25 – Battery Socket

J27 – GPIO Connect

WMP-19B/22B User’s manual

APPENDIX

43

Pin #

Signal Description

1

+5VSB

2

+3.3VSB

3

KP_SCL

4

KP_SDA

5

PWR_LED#

6

KP_P_LED

7

SATA_LED#

8

GND

9

GND

Pin #

Signal Description

1

+5VSB

2

+3.3VSB

3

KP_SCL

4

KP_SDA

5

PWR_LED#

6

KP_P_LED

7

SATA_LED#

8

GND

9

GND

J28 –CAP Front Bezel Button Light Sensor Connect

J29 –Light Sensor Connect

WMP-19B/22B User’s manual

APPENDIX

44

Pin #

Signal Description

Pin #

Signal Description

1

232_DCD#

2

232_DSR#

3

232_SIN

4

232_RTS#

5

232_SOUT

6

232_CTS#

7

232_DTR#

8

232_RI#

9

GND

10

+5VS / +12VS

Pin #

Signal Description

Pin #

Signal Description

1

DCD#

2

DSR#

3

SIN 4 RTS#

5

SOUT

6

CTS#

7

DTR#

8

RI# 9 GND

10

+5VS

J30 – Internal COM4 Serial Port

J31 – Internal COM4 TTL

J32 – External USB 3.0 Port

WMP-19B/22B User’s manual

45

Pin #

Signal Description

1

+5V

2

Data-

3

Data+

4

GND

5

SSRX-

6

SSRX+

7

GND

8

SSTX-

9

SSTX+

Pin #

Signal Description

J33 (RIGHT CH)

J42 (LEFT CH)

1

ROUT+

LOUT+

2

ROUT-

LOUT-

Pin #

Signal Description

1

Data0+

2

Data0-

3

Data1+

4

Data2+

5

Data2-

6

Data1-

7

Data3+

8

Data3-

J33, J42 – RIGHT / LEFT CH for Speaker

APPENDIX

J34 –External RJ45 Ethernet Port

WMP-19B/22B User’s manual

APPENDIX

46

Pin #

Signal Description

1

Power ON

2

GND

Pin #

Signal Description

1

+5V

2

USB_D-

3

USB_D+

4

GND

Pin #

Signal Description

Pin #

Signal Description

1

DVI Data2-

2

DVI Data2+

3

GND

4

NC 5 NC 6 DVI SCL

J35 – Power Switch connect

J36,J37,J38 – External USB 2.0 Port

J39 – External DVI-I Connector

WMP-19B/22B User’s manual

47

7

DVI SDA

8

VSYNC

9

DVI Data1-

10

DVI Data1+

11

GND

12

NC

13

NC

14

+5V

15

GND

16

Hot Plug Detect

17

DVI Data0-

18

DVI Data0+

19

GND

20

CRT_CLK

21

CRT_DATA

22

GND

23

DVI Clock+

24

DVI Clock-

C1

CRT_R

C2

CRT_G

C3

CRT_B

C4

HSYNC

C5

GND

C6

GND

Pin #

Signal Description

J40

Line Out (stereo) Green

J41

Microphone (stereo) Pink

Pin #

Signal Description

Pin #

Signal Description

1

232_DCD#

2

232_DSR#

3

232_SIN

4

232_RTS#

5

232_SOUT

6

232_CTS#

7

232_DTR#

8

232_RI#

9

GND

10

+5VS

J40 / J41 – External Audio Phone Jack

APPENDIX

J43 – Internal COM3 Serial Port

WMP-19B/22B User’s manual

APPENDIX

48

Pin #

Signal Description

1

SYS_RESET#

2

GND

3

GND

4

GND

Pin #

Signal Description

1

SYS_RESET#

2

GND

Pin #

Signal Description

Pin #

Signal Description

1

232_DCD

2

232_SIN

3

232_SOUT

4

232_DTR

5

GND

6

232_DSR

7

232_RTS

8

232_CTS

9

232_RI

10

Not Used

J44 – Reset Button

J45 – Reset connector

J46 – External COM2 Connector

WMP-19B/22B User’s manual

49

J47 – External COM1 Connector

Pin #

Signal Description

RS-232

RS-422

RS-485

1

Carrier Detect

Transmit Data -

Transmit Data -

2

Receive Data

Transmit Data +

Transmit Data +

3

Transmit Data

Receive Data +

NC

4

Data Terminal Ready

Receive Data -

NC

5

Ground

NC

NC 6 Data Set Ready

NC

NC

7

Request to Send

NC

NC 8 Clear to Send

NC

NC 9 Ring Indicator

NC

NC

APPENDIX

WMP-19B/22B User’s manual

APPENDIX

50

Battery Model133

BP-WMP226 22/3900 SA

Battery Type

Li-ion 2S2P

Minimum Capacity

3900 mAh

Nominal Voltage

7.2 V

Max. Charge Voltage

8.4V

Cut Off Voltage

6.0v

Suggested Charge

Current (Max.)

2A

System Continuous
Discharging Current

(Max.)

16.6 A

The End of Charge

Condition

150 mA/min

Discharge Protection

UVP/OCP

Charge Protection

OVP/OTP

Self-discharge Rate

10uA ~800 uA

Dimensions

133 x 47 x 21mm

Weight

240g max.

Ambient Temperature

0°C ~ +40°C

Storage Temperature

-20°C ~ +60°C

Energy

28.08Wh

Backup

53 W/ 40 min

B. Battery Pack Specifications (optional kit)

WMP-19B/22B User’s manual

APPENDIX

51

C. How to disable battery when system hang up

-WMP-19B/22B

1. When system hang up, press power button 10 seconds to turn

off system. If you can’t power on system by power button.
Please follow below step to reset system.

2. Remove AC power cord, then the battery LED will on.

3. Press volume up key 10 seconds, then all LED will turn on and

turn off

4. Plug in AC power cord again, press power button then you can

power on system.

WMP-19B/22B User’s manual

APPENDIX

52

D. Scrap Computer Recycling

If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform us as
soon as possible for the suitable solution. For the computers that
are no longer useful or work well, please contact with worldwide
distributors for recycling.

The worldwide distributors show on the following website:

http://www.wincomm.com.tw/contact.aspx

Note:
Follow the national requirement to dispose unit

WMP-19B/22B User’s manual