Page 1
INSTALLATION INSTRUCTIONS
2 WHEEL DOLLY KIT
MODEL WC10000VE
COMPONENT LIST
REF. # PART # DESCRIPTION QTY.
1 300066-14 Left Handle Support 1
2 61857-008 Handle 1
3 16205-004S Foot 1
4 300066-15 Right Handle Support 1
5 64326-024 Axle 1
6 43657-008 Wheel & Tire 2
16199-125 Parts Bag 1
113030-00 16199-025I
Page 2
STEP 1
Open hardware bag and account for all fasteners and components.
•
FASTENERS & MISC. COMPONENTS
(not shown in actual size)
7
12
19
13
20
14
15
10
11
9
8
16
17
18
21
22
FASTENER & COMPONENT LIST
REF # PART # DESCRIPTION QTY
7 91245-000 5/16” X 5” Bolt 4
8 64688-006 Spacer 2
9 20191-000 Shock Mount 2
10 64327-000 Hub Cap 2
11 93402-002 Hole Plug 2
12 56842-005 1/4” X 2” Carriage Bolt 2
13 47517-000 1/4” Nylock Hex Nut 2
14 466-000 1/4” X 3/4” Bolt 2
15 62912-000 Foam Strip 1
16 1178-000 Flat Washer 2
17 96286-006 Nylon Flat Washer 2
18 91672-011 5/16” X 4” Bolt 2
19 16249-000 5/16” Flange Lock Hex Nut 6
20 526-000 Flat Washer 6
21 16248-000 1/4” Flange Lock Hex Nut 2
22 16343-000 Axle End Protector 2
23 15775-019 Axle Bracket 2
213030-00 16199-025I
Page 3
STEP 2
Remove the generator from the pallet and block generator up 8 to 10 inches to
•
gain access to the botton of the cradle assembly. A lifting jack or hoist may also
be used if available.
STEP 3
Bolt shock mounts (ref. 9) to the bottom of the foot bracket (ref. 3) using hardware
•
(ref. 14 & 21). Place foot bracket (ref. 3) into the front cross channel of the cradle
and bolt on with hardware (ref. 18, 19, 20).
313030-00 16199-025I
Page 4
STEP 4
Place both axle brackets (ref. 23) into the rear cross channel of the cradle and bolt
•
on with hardware (ref. 7, 20, 19)
Tap one hubcap (ref.10) onto axle using a rubber mallet. Slide washer (ref. 16),
•
wheel (ref. 6) and spacer (ref. 8) onto axle (ref. 5). Then slide assembly through
the two axle brackets. Place other spacer, wheel and washer on axle and lower to
the ground. Place the other hubcap on the axle and tap into place with a rubber
mallet.
STEP 5
Install hole plugs (ref. 11) into ends of handle (ref. 2). Cut the foam strip (ref. 15)
•
in half using a scissors. Apply to the underside of the handle supports (ref. 1 & 4).
Bolt left and right handle supports (ref. 1 & 4) to the cradle using hardware on
•
cradle. Attach handle (ref. 2) using hardware (ref. 12, 17, 13). Tighten the nylock
hex nuts. Do not over-tighten so that the handle will move freely.
413030-00 16199-025I
Loading...