Page 1
W10000VE/A
GENERATOR
INSTALLATION AND
OPERATORS
WINCO INC. 225 S. CORDOVA AVE. LE CENTER, MN 56057 507-357-6821
MANUAL
SERVICE DEPT. 507-357-6831
www.wincogen.com
Page 2
TABLE OF CONTENTS
SAVE THESE INSTRUCTIONS 2
TESTING POLICY 2
SPECIFICATIONS 3
GENERATOR
SAFETY INFORMATION 3
ANSI SAFETY DEFINITIONS
INTRODUCTION 4
INTENDED USES
RESTRICTED USES
UNIT CAPABILITIES 4
GENERATOR CONNECTIONS
STARTING ELECTRIC MOTORS
PREPARING THE UNIT 5
UNPACKING
LUBRICATION
OIL RECOMMENDATIONS
OIL ALERT SYSTEM
GASOLINE
AUTOMATIC VOLTAGE REGULATOR
BATTERY INSTALLATION
BATTERY CHARGING
LIFTING EYE INSTALLATION
OPTIONAL DOLLY KIT
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed
during installation and maintenance of the generator. Read and
understand all instructions in the manual before starting and operating
the generator.
USING THIS MANUAL
Congratulations on your choice of a WINCO generator. You have
selected a high-quality, precision-engineered generator designed and
tested to give you years of satisfactory service.
To get the best performance from your new generator, it is important
that you carefully read and follow the operating instructions in this
manual.
Should you experience a problem please follow the “Troubleshooting
Tables” near the end of this manual. The warranty listed in the manual
describes what you can expect from WINCO should you need service
assistance in the future.
COPY YOUR MODEL AND SERIAL NUMBER HERE
No other WINCO generator has the same serial number as yours.
If you should ever need to contact us on this unit, it will help us to
respond to your needs faster.
MODEL __________________________________________________
INITIAL START UP 7
BASIC OPERATION
STARTING HINTS
CONNECTING THE LOADS 8
APPLYING THE LOADS
GROUNDING
WIRING
ENGINE CARE 9
MAINTENANCE SCHEDULE
CHANGING THE OIL
TROUBLESHOOTING 10
DUAL ELEMENT AIR FILTER
SPARK PLUG
CARBON CANISTER
GENERATOR CARE 11
EXERCISING THE GENERATOR
GENERATOR MAINTENANCE
CLEANING
RECEPTACLE PANEL WIRING DIAGRAM 11
36 MONTH LIMITED WARRANTY 12
SERIAL NUMBER _________________________________________
PURCHASE DATE _________________________________________
DEALER NAME ___________________________________________
DEALER PHONE # ________________________________________
TESTING POLICY
Before any generator is shipped from the factory, it is fully checked
for performance. The generator is loaded to its full capacity, and the
voltage, current, and frequency are carefully checked.
Rated output of generator is based on engineering tests of typical units,
and is subject to, and limited by, the temperature, altitude, fuel, and
other conditions specied by the manufacturer of applicable engines.
OPM-113
2
REV A
Page 3
SPECIFICATIONS
GENERATOR
1. ELECTRICAL SHOCK -
The output voltage present in this equipment can cause fatal electric
shock. This equipment must be operated by a responsible person.
Model W10000VE/A
Surge Watts 10,000
Continuous Watts 9,600
Volts 120/240
Amps 80/40
Generator Manufacturer Mecc Alte
Generator Model Number ES20F-160
Part Number 16346-025
Rotor Resistance 6.5 Ohms
Stator Resistance 0.124 Ohms
Regulation AVR
ENGINE
Engine Manufacturer Briggs & Stratton
Engine Model Number 543477
Type & Code 0614-G1
Spark Plug Gap 0.030 in
Intake Valve Clearance 0.007 - 0.0 in
Exhaust Valve Clearance 0.004 - 0.006 in
Oil Capacity 2.4-2.5 qts (78-80 oz)
A. Do not allow anyone to operate the generator without proper
instruction.
B. Guard against electric shock.
C. Avoid contact with live terminals or receptacles.
D. Use extreme care if operating this unit in rain or snow.
E. Use only three-pronged grounded receptacles
and extension cords.
F. Be sure the unit is properly grounded to an
external ground rod driven into the earth.
2. FIRE HAZARD -
Gasoline and other fuels present a hazard of possible explosion and/
or re.
A. Do not refuel when the engine is running or hot.
B. Keep fuel containers out of reach of children.
C. Do not smoke or use open ame near the generator set or fuel
tank.
D. Keep a re extinguisher nearby and know its proper use.
Fire extinguishers rated ABC by NFPA are appropriate.
E. Store fuel only in an approved container, and only in a well
ventilated area.
F. Follow local codes for closeness to combustible material.
SAFETY INFORMATION
This engine generator set has been designed and manufactured to
allow safe, reliable performance. Poor maintenance, improper or
careless use can result in potentially deadly hazards; from electrical
shock, exhaust gas asphyxiation, or re. Please read all safety
instructions carefully before installation or use. Keep these instructions
handy for future reference. Take special note and follow all warnings on
the unit labels and in the manuals.
ANSI SAFETY DEFINITIONS
DANGER:
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury. This signal word is to be
limited to the most extreme situations.
WARNING:
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION:
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may also be used to
alert against unsafe practices.
3. DEADLY EXHAUST GAS -
Exhaust fumes from any gasoline engine contain carbon monoxide, an
invisible, odorless and deadly gas that must be mixed with fresh air.
A. Operate only in well ventilated areas.
B. Never operate indoors including attached garages
C. Never operate the unit in such a way as to allow exhaust gases
to seep back into closed rooms (i.e. through windows, walls,
oors).
4. NOISE HAZARD -
Excessive noise is not only tiring, but continual exposure can lead to
loss of hearing.
A. Use hearing protection when working around this equipment for
long periods of time.
B. Keep your neighbors in mind when using this equipment.
5. CLEANLINESS -
Keep the generator and surrounding area clean.
A. Remove all grease, ice, snow or materials that create
slippery conditions around the unit.
B. Remove any rags or other materials that could create a
potential re hazard.
C. Carefully clean up any gas or oil spills before starting the unit.
3REV A
OMP-113
Page 4
6. SERVICING EQUIPMENT -
All service, including the installation or replacement of service parts,
should be performed only by a qualied technician.
UNIT CAPABILITIES
GENERATOR CONNECTIONS
A. Use only factory approved repair parts.
B. Do not work on this equipment when fatigued.
C. Never remove the protective guards, covers, or receptacle
panels while the engine is running.
D. Use extreme caution when working on electrical components.
High output voltage from this equipment can cause serious
injury or death.
E. Always avoid hot mufers, exhaust manifolds, and engine parts.
They can cause severe burns instantly.
F. The use of the engine-generator set must comply with all
national, state, and local codes.
INTRODUCTION
INTENDED USES
This engine generator set has been designed primarily for portable
heavy duty commercial use. Both 120 volt and 240 volt receptacles
are provided in the control panel to plug in your loads (lights, portable
tools, and small appliances). These units are dual wound generators,
therefore the 120 volt loads must be equally split with 1/2 of the rated
capacity available on each of the two 120 volt circuits.
This portable unit requires large quantities of fresh air for cooling the
engine and generator. For safety, long life and adequate performance,
these units should never be run in small compartments without positive
fresh air ow.
RESTRICTED USES
DO NOT remove from the cradle assembly. Removal of the generator
from the cradle assembly may cause excessive vibration and damage
to the engine-generator set.
DO NOT install and operate this generator in a small compartment,
i.e. generator compartments of vehicles, motor homes or travel
trailers. These compartments will not allow enough free ow of fresh
air to reach the engine generator set for cooling and will cause the
unit to overheat, damaging both the engine and generator. Small
compartments will also develop hot spots where there is very little air
ow and may cause a re.
PLEASE NOTE: There are 3rd party companies making enclosures for
generators that have been properly engineered. The use of these 3rd
party enclosures is acceptable as long as they have been certied and
meet current code.
W10000VE/A: 120 Volt and 240 Volt receptacles are provided for
connection to various loads. The diagram below represents this 9,600
watt (rated output) generator. A & B represent the 120 volt output legs
of this generator. Up to 4,800 watts at 120 volts (40 Amps) can be
drawn from the receptacles attached to either A or B output legs. This
generator is capable of producing 40 Amps of 240 volt current at C.
Check the appliance or tool nameplates for the current and voltage to
insure compatibility. Remember that power taken from C reduces the
power available at equally both A and B and vice versa.
STARTING ELECTRIC MOTORS
Electric motors require much more current (amps) to start them than to
run them. Some motors, particularly low cost split-phase motors, are
very hard to start and require 5 to 7 times as much starting current as
running current. Capacitor motors are easier to start and usually require
2 to 4 times as much starting current as running current. Repulsion
Induction motors are the easiest to start and require only 1 1/2 to 2 1/2
times as much starting as running current.
Most fractional horsepower motors take about the same amount
of current to run them whether they are Repulsion Induction (RI),
Capacitor (Cap), or Split-Phase (SP) type.
If the electric motor is connected to a hard starting load such as an air
compressor, it will require more starting current. If it is connected to a
light load, or no load such as a power saw, it will require less starting
current. The exact requirement will also vary with the brand or design
of the motor.
Self-exciting generators respond to severe overloading differently than
utility power. When overloaded, the engine is not able to supply enough
power to bring the electric motor up to operating speed. The generator
responds with high initial starting current, but the engine speed drops
sharply. The overload may stall the engine. If allowed to operate at very
low speeds, the electric motor starting winding will burn out in a short
time. The generator winding might also be damaged.
CAUTION: EQUIPMENT DAMAGE
Running the generator set under these conditions may result in
damage to the generator stator as well as the motor winding.
DO NOT attempt to operate at 50 cycles. These units are designed and
governed to operate at 60 cycles only.
OPM-113
The heavy surge of current required for starting motors is required for
only an instant. The generator will not be damaged if it can bring the
motor up to speed in a few seconds of time. If difculty is experienced
in starting motors, turn all other electrical loads off and if possible
reduce the load on the electric motor.
4
REV A
Page 5
PREPARING THE UNIT
A
C
A
B
SAE 30
10W-30
Synthetic 5W-30
5W-30
°F °C
OIL RECOMMENDATIONS
UNPACKING
CAUTION: EQUIPMENT DAMAGE
THIS UNIT HAS BEEN SHIPPED WITH OIL. Failure to maintain the
engine oil at the proper level will result in serious engine damage.
When you unpack your engine-generator set be sure to remove all the
information sheets and manuals from the carton.
1. As you receive your unit, it is critical to check it for any damage. If
any damage is noted, it is always easiest to refuse the shipment and
let WINCO take care of the freight claim. If you sign for the unit, the
transfer of the ownership requires that you le the freight claim
2. Before proceeding with the preparations of your new generator
for operation, take a couple of minutes to ensure the unit you have
received is the correct model and review the specication pages in this
manual to ensure that this unit meets your job requirements.
LUBRICATION
Before starting the engine, check that the crankcase has the proper
level of a good quality oil. The recommended grade oil and quantity
of oil required is listed in the engine operator’s manual and in the Oil
Recommendations section of this manual. The engine normally holds
2.4 to 2.5 quarts of oil. Use the dipstick (‘A’ in following image) to
ensure that you have the correct amount of oil. The full oil level mark
on the dipstick is depicted in the following image as ‘B’.
B
C
Outdoor temperatures determine the proper oil viscosity for the
engines. Use the chart to select the best viscosity for the outdoor
temperature range expected.
OIL ALERT SYSTEM
This generator is equipped with a low oil shutdown system. This Briggs
& Stratton engine uses an oil pressure switch system. If the system
senses low oil pressure, it will automatically shut down the engine. This
feature is designed to prevent costly repairs and downtime.
CAUTION: EQUIPMENT DAMAGE
Allowing the engine to shutdown repeatedly on low oil level may cause
excessive wear which can be cumulative.
GASOLINE
When using gasoline, always use fresh, clean, unleaded fuel. The
engine is certied to operate on unleaded gasoline with a minimum
octane rating of 87 or higher. Gasoline containing no more the 10%
ethanol is acceptable.
CAUTION: EQUIPMENT DAMAGE
Do not use unapproved gasolines, such as E15 or E85. Do not mix
oil in the gasoline. Use of unapproved fuels will damage the engine
components and void the engine warranty.
If needed, oil is added to the engine by removing the oil cap and adding
oil at this point. After lling the crankcase to the proper level, be sure
you properly tighten the oil ll cap (‘C’).
NOTE: This engine generator must be on a level surface before you
check or add oil to the system.
The necessity of using the correct oil and keeping the crankcase full
cannot be overemphasized. Engine failures resulting from inadequate
or improper lubricant are considered abuse and not covered by the
generator or engine manufacturer’s warranty.
A
Use of fuels with content of ethanol greater than shown above may
cause starting and/or performance problems. Always ensure that the
fuel is clean and free of all impurities.
WARNING: FIRE DANGER
Gasoline and its fumes are VERY explosive when proper precautions
are not taken.
Never use gasoline that has been stored for an extended period of
time as the fuel will lose its volatile properties and you will be left with
varnish residue. The varnish like substance will clog the carburetor and
will not burn properly.
The use of fuel additives, such as Sta-Bil, or an equivalent will minimize
the formation of fuel gum deposits. If a unit has been out of operation
for an extended period of time, it is best to drain old fuel from the
engine and replace with fresh fuel before attempting to start.
See the engine manual for special instruction for operating this unit at
over 5000 feet.
5REV A
OMP-113
Page 6
AUTOMATIC VOLTAGE REGULATOR
These engines produce enough direct current to keep the battery
charged under normal operating conditions, but were not intended to
be used as a battery charger.
WARNING: PERSONAL INJURY
Lead acid batteries produce explosive hydrogen gas when charging.
Keep sparks, ames, and burning cigarettes away from the battery.
Ventilate the area when charging or using the battery in an enclosed
space. Lead acid batteries contain sulfuric acid, which causes severe
burns. If acid contacts eyes, skin, or clothing, ush well with water. For
contact with the eyes, get immediate medical attention.
The following is a list of connections on the AVR. These have been
factory set and other than voltage adjustment, should never be
changed.
TERMINALS
Terminal 1 - Excitation Negative
Terminal 2 - Excitation Positive
Terminal 3 - AVR Power Supply
Terminal 4 & 5 - Voltage Sensing Input
Terminal 6 & 7 - Common for Sensing and Power Supply
VOLTS
To adjust generator output voltage.
Clockwise to increase voltage.
STAB
To prevent voltage hunting.
Clockwise to decrease stability and consequently the response time.
HZ
Sets the intervention level of the under-frequency protection.
These have been factory set and should never be changed.
BATTERY INSTALLATION
BATTERY CHARGING
Units have a small ywheel charger built into the engine ywheel
assembly for recharging the starting battery. This ywheel charger
generates a small AC current that passes through a diode assembly
to produce DC charging current of about 1 to 3 Amps. This circuit is
not designed to be used as a battery charging circuit to recharge dead
batteries.
LIFTING EYE INSTALLATION
The lifting eye is shipped loose along with a bag of parts. Install the
base of the lifting eye below the middle support. See diagram below.
Button head
cap screw
Washer
.375
Flange
.31258 - 18
This engine generator set is shipped with a battery tie down kit for
customer installation. This kit consists of a battery tie down and
hardware for installation of the customer supplied battery on the unit.
If you intend to use the power plant’s electric start system, you will
need to purchase and install a battery to operate it.
A 12 Volt battery, group U1 rated at 275 CCA or larger is recommended
for this electric start engine-generator set. Follow the battery
manufacturers recommendations for servicing and charging prior to
use. Connect the battery to the electric start system using the cables
provided.
CAUTION: EQUIPMENT DAMAGE
These electric start engines are NEGATIVE GROUND. Use extreme
caution when connecting the battery. Connect the NEGATIVE battery
terminal to GROUND.
For your safety, always connect the positive battery cable to the “bat+”
terminal rst. Then connect the negative battery cable to the “bat-”
terminal. Make sure all connections are clean an tight. Reverse the
sequence when disconnecting, disconnect the negative cable rst.
OPM-113
OPTIONAL DOLLY KIT
An optional 2-wheel dolly kit is available for this generator. The dolly kit
comes with its own instructions and parts list.
CAUTION: EQUIPMENT DAMAGE
Be sure to check the wheels properly before operating the generator.
6
REV A
Page 7
INITIAL START UP
The throttle control on these generators is preset and locked to operate
at 3600 RPM (nominal) with no load speed set at 3690 RPM. Only
a trained service technician should be allowed to adjust this speed
setting.
BASIC OPERATION
MANUAL STARTING
1. Check oil level, rell as needed.
2. Turn on the fuel supply. Ref “A”.
3. Engage the choke (“B”) by pulling it out. A warm engine
will require less choking than a cold engine.
4. Rotate the key switch (‘C’) briey to the START position. Repeat
if necessary.
NOTE: The starter life is improved by using shorter cycles with time
to cool off between cranking cycles. Do NOT operate the starter more
than 15 seconds during each minute.
5. Gradually push the choke as the engine warms up.
6. The engine should promptly come up to operating speed.
Refer to the engine manual for additional starting, operating, and
stopping instructions
1. Check oil level, rell as needed.
2. Turn on the fuel supply. Ref “A”.
NOTE: There is a second fuel valve under the fuel tank that is used
when removing the tank. This valve is normally left on.
A
3. Engage the choke (“B”) by pulling it out. A warm engine
will require less choking than a cold engine.
1. CHECK OIL LEVEL
2.CHECK & CLEAN AIR CLEANER
3. CHANGE OIL
4. REPLACE OIL FILTER
5. CLEAN COOLING FINS
B
See Operating and Maintenance Instructions
CHOKE
RUN
8 hours
25 hours
100 hours
100 hours
100 hours
TM
C
4. Rotate the key switch (‘C’) to the run position.
5. Pull the starter grip lightly until resistance is felt, then pull
briskly.
6. When the engine starts, open the choke gradually.
7. The engine should promptly come up to operating speed.
CAUTION:
Do not allow the starter grip to snap back against the engine. Return it
gently to prevent damage to the starter.
ELECTRIC STARTING
If the engine is cold and stiff or if the battery is not fully charged,
starting can be made easier by slowly hand cranking the engine
through the compression stroke before pushing the starter switch. This
permits the starter to gain momentum before the heavy load of the
compression stroke occurs. This minimizes the drain on the battery
and improves the possibility of starting under such adverse conditions.
Always keep the battery charged, especially during cold weather
operation.
CAUTION: EQUIPMENT DAMAGE
Never permit the choke to remain on after the engine has run for a
short time. It is not necessary to choke the engine when it is warm.
Avoid over-choking.
STARTING HINTS
1. COLD WEATHER
A. Use the proper oil for the temperature expected.
B. Use fresh winter grade fuel. Winter grade gasoline is blended to
improve starting. Do not use summer grade gasoline.
2. HOT WEATHER
A. Use the proper oil for the temperature expected.
B. Use only summer blended gasoline. Using gasoline left over from
winter may cause the unit to vapor lock.
STOPPING AND STORING
1. Move the key to the “OFF” position.
2. Turn off the fuel supply valve.
3. Before extended storage (over 30 days) certain precautions
must be taken to ensure the fuel doesn’t deteriorate and clog the
fuel system.
NOTE: The use of a fuel additive, such as Sta-Bil or equivalent will
minimize the formation of gum deposits during storage. The additive
may be added to gasoline in the engines fuel tank or to gasoline in a
storage container.
A. Add the fuel stabilizer to the fuel in the tank and run for 2 minutes
to circulate the stabilizer throughout the fuel system.
B. If you choose to remove the remaining fuel from the fuel tank, it
must be drained into an approved container.
C. Start the engine and allow it to run until all the fuel in the
carburetor and the fuel lines has been used up and the engine
stops.
NOTE: Running the engine to use up the fuel in the lines and
carburetor will still leave a small amount of fuel in carburetor. It is best
extended storage to treat the fuel before draining.
D. While the engine is warm, drain the oil and rell with fresh oil.
E. Clean dirt and chaff from cylinder, cylinder head ns, blower
housing, screen, and mufer areas.
F. Store in a clean and dry area.
7REV A
OMP-113
Page 8
OPERATING SPEED
The engine-generator must be run at the correct speed in order to
produce the proper electrical voltage and frequency.
CAUTION: EQUIPMENT DAMAGE
The output voltage should be checked to ensure the generator is
working properly prior to connecting a load to the generator. Failure to
do so could result in damage to equipment plugged into the unit and
possible injury to the individual.
All small engines that use a governor spring have a tendency to slow
down when a load is applied. When the electrical load is connected
to the generator, the engine is more heavily loaded, and as a result,
the speed drops slightly. This unit is equipped with an AVR that
automatically adjusts output depending on RPM speed and applied
load. The slight variation in speed also affects the frequency of the
output current. This frequency variation has no appreciable effect
in the operation of motors, lights, and most appliances. However,
electronic equipment and clocks may be affected if correct RPM is not
maintained. See Load vs. Output chart.
CONNECTING THE LOADS
APPLYING THE LOADS
Allow the engine to warm up for two or three minutes before applying
any load. This will allow the engine to reach normal operating
temperature and oil to circulate throughout the engine. A shot warm-up
time will permit the engine to work more efciently when the load is
applied and will reduce the wear in the engine, extending its life.
Receptacles have been provided to allow loads to be connected to the
generator. The loads should be added one at a time. If a large motor
is being started: or multiple motors are being started, they should be
started individually and the largest should be started rst.
CAUTION: EQUIPMENT OVERLOAD
Keep the generator load within in the generator and receptacle
nameplate rating. Overloading may cause damage to the generator
and/or the loads.
Although individual units and models vary slightly, the normal voltage
and frequency of the engine-generator described in this manual are
approximately as follows, under varying loads:
LOAD vs. OUTPUT
Generator
Load
None 3690 61.5 120V
Half 3600 60.0 120V
Full 3510 58.5 120V
The speed of the engine was carefully adjusted at the factory so that
the generator produces the proper voltage and frequency. For normal
usage, the speed setting should not be charged. If the generator is
being run continuously on a very light load, it is often advisable to lower
the operating speed slightly.
Reference “A” in the following image is the speed adjustment for this
engine.
A
CAUTION: EQUIPMENT DAMAGE
SPEED ADJUSTMENTS SHOULD ONLY BE MADE BY A QUALIFIED
SERVICE TECH. Whenever making any speed adjustments, check the
unit with a voltmeter and a frequency meter or a tachometer and be
sure the voltage and speed are correct.
Speed
(RPM)
Frequency
(Hz)
Voltage
Most electric tools and appliances will have the voltage and amperage
requirements on their individual nameplates. When in doubt, consult
the manufacturer or a local electrician. The nameplate amperage rating
for electric motors can be misleading. See “Starting Electric Motors” in
the Unit Capabilities.
The engine governor will automatically adjust itself to the load.
No harm to the generator will result if it is operated with no load
connected. Proper utilization of the receptacles located on the control
panel is necessary to prevent damage to either the receptacles or
the generator. The generator is a limited source of electrical power,
therefore, pay special attention to the receptacle and generator ratings.
The nameplate rating can be obtained through a single receptacle as
long as the receptacles amperage rating is not exceeded.
GROUNDING
All units must be grounded. Drive a 3/4 or 1” copper pipe or rod into
the ground close to the engine-generator set. The pipe must penetrate
moist earth. Connect an approved ground clamp to the pipe. Run a
no. 10 Awg wire from the clamp to the generator ground lug on the
receptacle panel. Do not connect to a water pipe or to a ground used
by a radio system. The engine-generators covered in this manual were
designed primarily for portable use. If you are connecting into a building
wiring system that is already grounded using the 14-60 4 wire plug, you
do not have to ground the unit.
WARNING: PERSONAL DANGER
DO NOT OPERATE THIS GENERATOR INDOORS, The unit should
be stored in a warm, dry location. During a power outage, move the
unit outdoors to a at, dry location such as a driveway or sidewalk.
Output voltage should be checked periodically to ensure continued
proper operation of the generating plant and appliances. If the
generator is not equipped with a voltmeter, it can be checked with a
portable meter.
OPM-113
8
REV A
Page 9
WIRING
e. Install the oil filter by hand until the gasket
contacts the oil filter adapter, then tighten the oil
filter 1/2 to 3/4 turns.
f. Replace oil drain plug.
g. Remove oil filler plug and refill with new oil.
Refer to the table on page 5 for the proper
grade of oil based on your operating
temperature.
NOTE: This engine requires 78 to 80 ounces of oil
if it is completely drained. Use caution when refilling
the engine as some residual oil may have remained
in the engine. Always use the dipstick when filling
the engine with oil to prevent overfilling.
h. Replace filler plug.
I. Start the engine and warm it up.
J. After warming up the engine, recheck the oil
level and refill as necessary to bring it to the
proper level. See page 5 for proper oil level.
Maintenance Chart
Plug your tools such as drills, saws, blowers, sump pump, and
other items to be powered directly into the generator receptacles.
Before plugging in all the tools and cord sets, recheck the rating
of the generator set. Be sure it can handle the intended load and
is compatible with the voltage, phase, and current ratings. ‘Hard
wiring’ this unit directly into a temporary construction site electrical
system is NOT A SIMPLE DO-IT-YOURSELF JOB. For your safety,
all wiring must be done by a qualied electrician and conform to the
National Electric Code and comply with all state and local codes and
regulations. Check with local authorities before proceeding.
WARNING: PERSONAL DANGER
A fully isolated, double pole double throw manual transfer switch must
be installed any time a generator is being connected to an existing
distribution system.
1. These engine-generator sets are designed for portable heavy duty
commercial use. Receptacles are provided on the control panel to
permit 120 and 240 Volt portable appliances and tools to be plugged
directly into them. Please note that the 3-wire 240 Volt receptacle(s)
on these units are designed to power only 240 Volt tools. There are
two hot leads and a ground wire, but no neutral connection, in the
3-wire 240Volt receptacle. A 4-wire receptacle (two hot, one ground,
and one neutral) has been provided on the control panel for use in
temporary power applications requiring 120/240 Volt power.
2. If the generator set is connected to an existing distribution system,
a fully isolated manual transfer switch, specically designed for use
with GFCI, must be installed. The transfer switch prevents damage to
the generator and the other circuit components if main line power is
restored while the generator is connected. Installing a transfer switch
also permits the use of normal fusing.
ENGINE CARE
MAINTENANCE SCHEDULE
First 5 Hours
x Change oil
Every 8 Hours or Daily
x Check engine oil level
x Clean area around muffler and controls
Every 100 Hours or Annually
x Clean or change air filter *
x Clean pre-cleaner (if equipped) *
x Change engine oil and filter
x Replace spark plug
x Check muffler and spark arrester
Every 250 Hours or Annually
x Check valve clearance. Adjust if necessary.
Every 400 Hours or Annually
x Change air filter
x Replace fuel filter
x Clean air cooling system *
x Clean oil cooler fins *
* In dusty conditions or when airborne debris is present, clean more often.
If major engine service or repair is required, contact an authorized
engine service center. The manufacturer of these engines has
established an excellent world-wide engine service organization.
Engine service is very likely available from a nearby authorized dealer
or distributor.
CHECKING THE OIL LEVEL
3.Many homes and construction sites are wired for at least 60 to
100 Amp entrance service, much greater than the capacity of this
portable generator. When installing the generator at these sites, a
secondary emergency distribution panel may have to be installed.
The emergency distribution panel must be installed by a licensed
electrician according to all applicable codes. The electrician will move
the critical circuits to be powered during the outage to the emergency
panel. Keep in mind only a limited amount of amperage is available
from the generator set. Some circuit breakers may still have to be
turned off to prevent an overload on the generator during the initial
start up. See the nameplate on your generator for the amperage
capabilities of your unit.
CAUTION: EQUIPMENT DAMAGE
Failure to properly limit and balance the load applied to the generator
will cause the generator to produce low voltage and may damage
the engine generator set. It may also cause severe damage to the
loads connected to the generator at that time. Improper loading of the
generator set constitutes abuse and will not be covered by warranty.
The oil level must always be checked before the engine is started.
Refer to page 5 of this manual for instructions on checking the oil level.
Take care to remove any dirt or debris from around the oil plug before
removing. Be sure the oil level is maintained.
CHANGING THE OIL
Refer to the Maintenance Schedule Chart for required oil change
intervals.
A. Start the engine and warm it up, stop the engine and remove the
spark plug wire to prevent it from accidentally being started.
B. This engine has an oil drain valve for your convenience. Attach a
neoprene hose and drain the oil into an approved container.
Neoprene Hose, 1/2” I.D.
Cut to length
9REV A
OMP-113
Page 10
C. Remove the oil lter and dispose of it properly.
D. Before you install the new oil lter, clean the lter mounting base
and coat the seal of the new oil lter will clean engine oil.
E. Install the oil lter by hand until the gasket contacts the oil lter
adapter, then tighten the oil lter 1/2 to 3/4 turns.
F. Replace oil drain bolt making sure the sealing washer is in place.
G. Remover the oil lter plug and rell with new oil. Make sure to use
the proper grade oil based on your operating temperature.
SPARK PLUG
Replace annually or every 100 above hours of operation. Always
replace with the same spark plug that came in the engine and check
gap before installing. Spark plug gap is 0.030”. Poor spark will also
occur if spark plug wire does not t rmly on spark plug. If this happens,
reform the terminal to t rmly on spark plug tip.
NOTE: This engine requires 2.4-2.5 qts (78 to 80 oz) of oil if it is
completely drained. Use caution when relling the engine as some
residual oil may have remained in the engine. Always use the dipstick
when lling the engine with oil to prevent overlling.
H. Replace lter plug.
I. Start the engine and warm it up.
J . After warming up the engine, recheck the oil level and rell as
necessary to bring it to the proper level.
DUAL ELEMENT AIR FILTER
Clean and/or replace the foam pre-cleaner and the air lter annually or
every 100 hours. Service more often under dusty conditions.
WARNING: EQUIPMENT DAMAGE
Never start or run the engine with the air lter removed.
A. Loosen snaps (‘A’) and remove cover (‘B’).
B
A
D
E
G
F
B. Remove the nut (‘D’) and the retainer (‘E’).
C. Remove the air lter (‘F’).
D. Remove the pre-cleaner (‘G’) from the air lter.
E. To loosen debris, gently tap the air lter on a hard surface. If the
air lter is excessively dirty replace with a new lter.
CARBON CANISTER
Designed to collect, store, and dispose of fuel vapors created in the
fuel tank/fuel system. The canister should last the life of the unit as long
as it stays dry.
TROUBLESHOOTING
Problem Possible Causes
Won’t start Low oil level
Fouled spark plug
Out of fuel
Start switch in OFF position
Fuel Valve turned off
Plugged fuel lter
Blown fuse in key switch
Voltage too low AVR adjustment
Defective stator
Defective rotor (eld)
Defective AVR
Circuit breaker trips Defective load
Defective receptacle
Excessive load
Voltage too high Engine speed is too high
AVR Adjustment
Generator overheating Overloaded
Insufcient ventilation
No output voltage Short in load (disconnect)
Tripped or defective circuit breaker
Broken or loose wire
Defective receptacle
No residual magnetism (in generator)
Defective stator
Defective rotor (eld)
Defective AVR
Shorted diodes on rotor
GFCI receptacle tripped
NOTE: Do NOT use pressurized air or solvents to clean the lter.
Pressurized air can damage the lter and solvents will disolve the lter.
F. Wash the pre-cleaner in liquid detergent and water. Then allow it
to thoroughly air dry. DO NOT oil the pre-cleaner.
G. Install the pre-cleaner to the air lter..
H. Install the air lter and secure with retainer and nut.
I. Install and secure the cover.
OPM-113
10
REV A
Page 11
GENERATOR CARE
Proper care and maintenance of the generator is necessary to ensure
a long trouble free life.
B. Receptacles - Quality receptacles have been utilized. If a
receptacle should become cracked or otherwise damaged,
replace it. Using damaged or cracked receptacles can be both
dangerous to the operator and destructive to the equipment.
EXERCISING THE GENERATOR
The generator should be operated every three to four weeks. It should
be operated for a period of time sufcient to warm the unit up and to
dry out any moisture that has accumulated in the windings. If left, this
moisture can cause corrosion in the winding. Frequent operation of the
engine-generator set will also ensure that the set is operating properly
should it be needed in an emergency.
GENERATOR MAINTENANCE
Any major generator service, including the installation or replacement
of parts, should be performed only by a qualied electrical service
technician. USE ONLY FACTORY APPROVED REPAIR PARTS.
A. Bearing - The bearing used in these generators is a heavy duty,
double sealed ball bearing. They require no maintenance or
lubrication.
CLEANING
Remove dirt and debris with a cloth or brush. DO NOT use high
pressure spray to clean either the engine or the generator. The high
pressure spray could contaminate the fuel system and the generator
components.
1. Keep the air inlet screen on both the engine and generator free of
any dirt or debris to ensure proper cooling. At least yearly, remove
the blower housing on the engine and clean the chaff and dirt out of
the engine cooling ns and y wheel. Clean more often if necessary.
Failure to keep these areas clean may cause overheating and
permanent damage to the unit.
2. Periodically clean mufer area to remove all grass, dirt, and
combustible debris to prevent a re.
3. On engine mufers equipped with spark arresters, the spark arrester
must be removed every 50 hours for cleaning and inspection. Replace
if damaged.
GND
RECEPTACLE PANEL WIRING DIAGRAM
G2
G1
N
G1
N
GND
GND
G1
G2
G2
G1
GND
G1
G2
G2
G1
G1
GND
G2
40 AMP
G2
TIME METER
G1
G1
N
G1
N
N
G2
N
GNDGND
G1
N
G1
G2
GND
N
GND
N
G1
N
G2
G1
G2
G2
N
N
G1
G1
G1
N
G2
N
G2
G1
G1
N
G1
N
G1
11REV A
OMP-113
Page 12
36 MONTH LIMITED WARRANTY
WINCO warrants to the original purchaser for 36 months or 1000 hours, whichever occurs rst, that goods manufactured or supplied by it will be
free from defects in workmanship and material, provided such goods are installed, operated and maintained in accordance with WINCO written
instructions and applicable codes.
WINCO’s sole liability, and Purchaser’s sole remedy for a failure under this warranty, shall be limited to the repair of the product. At WINCO’s
option, material found to be defective in material or workmanship under normal use and service will be repaired or replaced. For warranty service,
return the product within the warranty period, to your nearest WINCO Authorized Service Center or to WINCO in Le Center Minnesota.
Duration Consumer, Commercial and Rental
Parts & Labor: 24 Months
Parts Only: 24-36 Months
EXCLUSIONS:
• Normal maintenance consumables or labor.
• This warranty does not cover travel time, mileage or labor for removal or re-installation of WINCO product from its application.
• Normal wear and tear.
• Costs of rental equipment.
• WINCO does not warrant engines. Engines are covered exclusively by the warranties of their respective manufacturers.
• WINCO does not warrant component parts that are warranted by their respective manufacturers.
• WINCO does not warrant modications or alterations which were not made by WINCO.
• WINCO does not warrant products which have been subjected to misuse and/or negligence or have been involved in an accident.
Proof of proper maintenance must be furnished upon request.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE DESCRIBED HEREIN. THERE ARE NO OTHER WARRANTIES,
EXPRESSED OR IMPLIED, OR OTHERWISE CREATED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, OR
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.
WINCO is liable for the repair or replacement of the product only and is not liable for incidental or consequential damages as permitted by your
state. This warranty gives you specic legal rights which may vary from state to state.
WINCO INC. • 225 S. CORDOVA AVE. • LE CENTER, MN 56057 • 507-357-6821
OPM-113
12
REV A
Loading...