Winco IV Pole User Manual

Page 1 of 8

IV -

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

before attempting to use this product; otherwise injury may occur.

Winco assumes no responsibility for damage or injury caused by improper assembly,

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

IV Pole Attachm ent

For Models:

2570, 2571, 2572, 2573, 2574, 2575, 5251,5261, 5271, 5281, 5291, 5351,
5361, 5400,5560,5570,5580,5670, 5680,5851,5861,6530,6531, 6540,
6541, 6550, 6551, 6560, 6570, 6571, 6700, 6710, 6740, 6750, 6940,
6950, 6980, 6990

If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone]

installation, use, or maintenance of these products.

TO REDUCE THE RISK OF INJURY TO PERSONS:

1. READ AND FOLLOW ALL DIRECTIONS.

2. DO NOT use the IV pole for pulling, moving, or holding the chair in place.

3. DO NOT use this attachment in any location or on products other than those listed in these
instructions.

4. DO NOT make any modifications to the bracket or pole.

5. IV Pole and included bracket are designed for hanging IV solutions ONLY.

6. Immediately remove from service; Any chair with mechanical or visible damage.

7. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.

8. SAVE THESE INSTRUCTIONS for future reference and training.

5516 Southwest 1

Ocala, FL 34474

1-800-237-3377 / 352-854-2929 / Fax: [phone]

e-mail: [e-mail]

Visit us on the web: www.wincomfg.com

006312 Revision F Date 10-22-13 JWC

CUSTOMER INSTRUCTIONS

st

Lane

FIG. 4

●Parts Included:

480500

FIG. 1

FIG. 3

NOTE:

FIG. 2

Pictures shown with 227600A OPTION

●IV Pole Attachment

Models: 5251, 5261, 5291, 5351, 5361, 5851, 5861, 6530, 6531, 6540, 6541, 6 570, 657 1

Description: Qty. Part Number
IV U-Bracket Assembly 1 227600 (LEFT)
227605 (RIGHT)

¼-20 Nylon Lock-nut (1-installed) 3 566204
¾” Phillips-head Screw (installed) 1 566504
2¾” Phillips-head Scre w 2 566571
IV Pole 1

●Tools needed:

• Phillips Head Screwdriver

• 7/16” wrench (multiple size wrench included)

• Powered tools NOT recommended –

●Assembly Instructions

1. Locate the rear-side of the chair and place the
“IV U-Bracket Assembly” onto the rear chair
frame rail. (FIG.1)

Left & Right is determined – as if sitting

2. Next insert the (2) 2¾” screws into the holes provided
on the bracket assembly. (FIG.2)

3. Secure the bracket to the chair frame using the (2)

nylon lock-nuts.

Tighten using the wrench provided. (FIG.3)

4. Insert the IV Pole.
Your chair should look like that of (FIG.4) when

assembly is complete.

006312 Revision F Date 10-22-13 JWC

Page 2 of 8

in the chair

NOTE:

●Parts Included:

IV Pole 1 480500

FIG. 1
FIG. 3

FIG. 4

FIG. 2

IMPORTANT:

FIG. 2A

527 ONLY

●IV Pole Attachment

Models: 5271, 5281, 6550, 6551

Description: Qty. Part Number
IV U-Bracket Assembly 1 227600 (LEFT)

227605 (RIGHT)
IV Spacer 1 227607
1” Grey Cap 2 700700

¼-20 Nylon Lock-nut (1 installed) 3 566204
¾” Phillips-head Screw (installed) 1 566504
2¾” Phillips-head Scre w 2 566571

●Tools needed:

• Phillips Head Screwdriver

• 7/16” wrench (multiple size wrench included)

• Powered tools NOT recommended –

●Assembly Instructions

1. Locate the proper location on the chair for the
“IV U-Bracket Assembly”. (FIG.1 & 1A)

Left & Right is determined – as if sitting

2. Insert the “IV Spacer” into the “IV U-Bracket”

(FIG. 2 or FIG.2A) and place onto chair frame.

527 “IV Spacer” s hould be placed towards

the top of the “IV U-bracket”. (FIG.2A)

3. Insert the two screws through the holes in the
“IV U-Bracket”. (FIG.2B)

4. Screw on the nylon lock-nuts and, using the wrenc h
provided, tighten the lock-nuts to the bracket. (FIG.3)

5. Your chair should look similar to that of (FIG.4)

006312 Revision F Date 10-22-13 JWC

Page 3 of 8

in the chair

NOTE:

●Parts Included:

IV Pole 1 480500

FIG. 1
FIG. 3

FIG. 4

FIG. 2

●IV Pole Attachment

Models: 2570, 2571, 2572, 2573, 2574, 2575

Description: Qty. Part Number
IV U-Bracket Assembly 1 227600 (RIGHT)

227605 (LEFT)
IV Spacer 1 227607
1” Grey Cap 2 700700

¼-20 Nylon Lock-nut (1 installed) 3 566204
¾” Phillips-head Screw (installed) 1 566504
2¾” Phillips-head Scre w 2 566571

●Tools needed:

• Phillips Head Screwdriver

• 7/16” wrench (multiple size wrench included)

• Powered tools NOT recommended –

●Assembly Instructions

6. Locate the proper location on the chair for the
“IV U-Bracket Assembly”. (FIG.1)

Left & Right is determined – as if sitting

7. Insert the “IV Spacer” into the “IV U-Bracket”
(FIG.2) and place onto chair frame.

8. Insert the two screws through the holes in the
“IV U-Bracket”. (FIG.3)

9. Screw on the nylon lock-nuts and, using the wrench
provided, tighten the lock-nuts to the bracket. (FIG.3)

10. Your chair should look similar to that of (FIG.4)

006312 Revision F Date 10-22-13 JWC

Page 4 of 8

in the chair

●Parts Included:

FIG. 2A

FIG. 2

FIG. 1

NOTE:

in the chair

FIG. 4

FIG. 3

●IV Pole Attachment

Models: 5560, 5680, 6560, 6740, 6750, 6940, 6950, 6980, 6990

Description: Qty. Part Number
IV Bracket Assembly (

IV Bracket Assembly
¼-20 Nylon Lock-nut (installed) 1 566204
¾” Phillips-head Screw (installed) 1 566504

●Tools needed:

• Phillips Head Screwdriver (5560/6560 ONLY)

• ½” Wrench

• 3/16” Allen Wrench

• Powered tools NOT recommended –

●Assembly Instructions
5560/6560 & 6980/699 0 (Right Side ONLY)

(6940/6950 & 6980/6990 Left Side ONLY instructions on next page)

1. First, check the bracket that came with your
IV Pole Attachment Kit. Verify that the screw and
lock-nut, already installed, are in their proper location.

(FIG. 1

2. Locate the left or right rear side for 5560/6560.
Locate the right-rear side for 6980/6990. (FIG.2)

3. Unscrew the bolts in the cross brace. (FIG.2A)

Left & Right is determined – as if sitting

4. Place the “IV Bracket” over the cross brace,

reinsert the screws, and tighten to a snug fit. (FIG.3)

5. Your chair should look like (FIG.4).

006312 Revision F Date 10-22-13 JWC

Page 5 of 8

5560, 6560, 6940, 6950) 1 227610

(6980, 6990) 1 227610B

(6940/6950/6980/6990 ONLY)

(6940/6950/6980/6990 ONLY)

NOTE:

NOTE:

FIG. 2

FIG. 3

FIG. 4

FIG. 4A

FIG. 6

FIG. 1

FIG. 5

Page 6 of 8

●Assembly Instructions
5680, 6740, 67 50, 6940/6950 & [6980/6990 (Left Side Only)]

1. First, check the bracket that came with your
IV Pole Attachment Kit. Verify that the screw and
lock-nut, already installed, are in their proper location.

(FIG. 1)

2. Locate the left or right rear side for 6940/6950.
Locate the left rear side for 6980/6990.

Left & Right is determined – as if sitting

in the chair

3. CAREFULLY place the chair on it’s side &
And open the swing arm all the way. (FIG.2)

4. Using a ½” wrench & a 3/16” allen wrench unscre w
the swing-arm hinge bolt. (FIG.3)

Some FORCE may need to be applied to the

allen wrench in order to loosen the hinge bolt

5. Take the loosened bolt out of the arm bracket, lift
upholstered swing-arm off of frame, and place on
floor.

6. Use a ½” wrench and REMOVE the bolts from the
hinge bracket. (FIG.4)

7. Line up the “IV Bracket” with the holes in the
upholstered arm. Be sure the pre-installed screw
and nut on the “IV Bracket” is towards the
bottom. (FIG.4A)

8. Place the arm bracket on top of the “IV Bracket”
and re-install the 2 bolts using a ½” wrench. (FIG.4)

9. Re-install the upholstered arm onto the chair frame

(FIG.5)

10. Your chair should look like (FIG.6)

006312 Revision F Date 10-22-13 JWC

●Parts Included:

FIG. 1

FIG. 3

NOTE:

FIG. 2

FIG. 4

●IV Pole Attachment

Models: 5400, 5570, 5580, 5670, 6700, 6710

Description: Qty. Part Number

IV Bracket Assembly 1 227630 (LEFT or RIGHT)
¼-20 Nylon Lock-nut (installed) 1 566204
¾” Phillips-head Screw (installed) 1 566504
IV Pole 1 480500

●Tools needed:

• Phillips Head Screwdriver

• Powered tools NOT recommended –

●Assembly Instructions

1. Locate the rear-side of the chair and remove the 2 screws
from the rear-brace (FIG.1)

Left & Right is determined – as if sitting

2. Next, line up the holes in the IV bracket with the holes in the
rear-brace. (FIG.2)

Nut and bolt pre-installed on the IV tube should be in
down position. (FIG.2-ARROW)

3. Secure the bracket to the chair frame using the (2)
screws previously removed in step 1. (FIG.3)

5. Insert the IV Pole.
Your chair should look like that of (FIG.4)

when assembly is complete.

006312 Revision F Date 10-22-13 JWC

Page 7 of 8

in the chair

Page 8 of 8

006312 Revision F Date 10-22-13 JWC