Winco EIC-400, EIC-400B Operating Instructions Manual

PROFESSIONAL

INDUCTION COOKTOP

Operating Instruction Manual

Model Voltage

EIC-4 00 120V ~ 60Hz 180 0W 15A 120 – 460° F

EIC-4 00B 240V ~ 60Hz 320 0W 13.3A 120 – 460° F

BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS

Congratulations on your purchase of this WINCO commercial induction range. WINCO takes pride in the quality of
its products. When used as intended and with proper care and maintenance, you will experience years of reliable
operation from this equipment. To ensure best results, it is important that you read and follow the instructions in this
manual carefully. It’s important to save these instructions for future reference.

Power

(W)

Amps Temp R ang e

50 – 240° C

50 – 240° C

Dimensions

Width Depth Height

13"

330mm

13"

330mm

15-3/8"
390mm

15-3/8"
390mm

4"

100mm

4"

100mm

Professional Induction Cooktop

Important For Future Reference

Please complete this information and retain this manual for the life of the product. For
Warranty Service and/or parts, this information is required. Please see Page 8 for More
information on your Warranty and how to register.

EIC-400 / -400B

EIC-4

Model Number Serial Number Date Purchased

WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE

!

PROPERTY DAMAGE, INJURY OR DEATH. READ THE
INSTALLATION, OPERATION AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING
OR SERVICING THIS EQUIPMENT.

CAUTION: THESE MODELS ARE DESIGNED, BUILT
AND SOLD FOR COMMERCIAL USE ONLY. IF THESE

!

MODELS ARE POSITIONED SO THE GENERAL
PUBLIC CAN USE THE EQUIPMENT, MAKE SURE
THAT CAUTION SIGNS, WARNINGS AND OPERATING
INSTRUCTIONS ARE CLEARLY POSTED NEAR EACH
UNIT SO THAT ANYONE USING THE EQUIPMENT WILL
USE IT CORRECTLY AND NOT INJURE THEMSELVES OR
HARM THE EQUIPMENT.

AVERTISSEMENT: TouTE INSTAllATIoN, RéglAgE,
ModIfIcATIoN, RépARATIoN ou ENTRETIEN
INcoRREcT pEuT occASIoNNER dES doMMAgES
MATéRIElS, dES blESSuRES gRAVES ou lA MoRT.
lIRE lES INTRucTIoNS d'INSTAllATIoN, d'uTIlISATIoN ET
d'ENTRETIEN ATTENTIVEMENT AVANT d'INSTAllER ou dE
RépARER cET AppAREIl.

ATTENTIoN: cES ModèlES SoNT coNçuS, fAbRIquéS,
ET VENduS pouR uN uSAgE coMMERcIAl SEulEMENT.
SI cES ModèlES SoNT plAcéS pouR quE lE gRANd
publIc puISSE lES uTIlISER, ASSuREz-VouS quE lES coNSIgNES
d’ATTENTIoN, d'AVERTISSEMENT, ET lES INSTRucTIoNS
d'uTIlISATIoN SoIENT clAIREMENT AffIchéES pRèS dE
chAquE uNITé dE SoRTE quE N'IMpoRTE quEl uTIlISATEuR dE
l'AppAREIl l'EMploIE coRREcTEMENT ET NE SE blESSE pAS ou
N'ENdoMMAgE pAS l'AppAREIl.

!

!

WARNING: A FACTORY AUTHORIZED SERVICE
PROVIDER SHOULD HANDLE ALL MAINTENANCE

!

AND REPAIR. BEFORE DOING ANY MAINTENANCE
OR REPAIR, FOLLOW THE SERVICE SET UP
ARRANGEMENT ON PAGE 8.

Introduction

Congratulations on the purchase of your WINCO machine. Please take the time to carefully read through this manual to ensure the machine is
operated and maintained properly, to ensure the best possible performance from this product for many years.

WINCO will not accept liability if:

• The instructions in this manual have not been followed correctly.

• Non-authorized personnel have tampered with the machine.

• Non-original spare parts are used.

• The machine has not been handled and cleaned correctly.

• There is any use damage to the unit.

2

AVERTISSEMENT: uN TEchNIcIEN AuToRISé pAR
l'uSINE dEVRA EffEcTuER TouT l'ENTRETIEN ET lES
RépARATIoNS. AVANT dE fAIRE TouT ENTRETIEN ou
RépARATIoN, VEuIllEz coNTAcTER WINco.

!

Table of Contents

Specications .............................................................................. 1

Warnings ..................................................................................... 2

Introduction ................................................................................ 2

Table of Contents ....................................................................... 3

Packaging .................................................................................... 3

Important Safeguards ................................................................ 4

Consignes de sécurité importantes ........................................ 5

Operation .................................................................................... 6

Cleaning, Care & Maintenance ................................................. 7

Safety ........................................................................................... 7

Professional Induction Cooktop

Service & Repair .......................................................................... 7

Troubleshooting ......................................................................... 7

Limited Warranty ....................................................................... 8

Package Contents

All units come with an Operating Instruction Manual
and the following:

• EIC-400 / -400B Induction Cooktop

WINCO prides itself on quality and service, ensuring that at the time of
packing, all products are supplied fully functional and free of damage.
Should you nd any damage as a result of freight, please contact your
WINCO dealer immediately.

Unpacking the Equipment

DISPOSE OF ALL PACKAGING MATERIALS IN AN
ENVIRONMENTALLY RESPONSIBLE MANNER.

1. Remove all packing materials and tape, as well as any protective
plastic and cardboard, from the unit.

2. Clean any glue residue left over from the plastic or tape.

3. Place the unit in the desired position and height.

SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN
PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES
ARENEEDED.

NOTE

Please remember that this manual and the warning labels do not replace the need to be alert, to properly train
and supervise operators, and to use common sense when using this equipment.

3

Important Safeguards

These instructions should be followed at all times. Failure to follow
these instructions could result in injury to yourself and others.

WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY
PRECAUTIONS AND COMMON SENSE SHOULD BE FOLLOWED,
INCLUDING BUT NOT LIMITED TO THE FOLLOWING:

1. Read all instructions. Do not use this appliance for anything other
than its intended use.

2. DO NOT touch any surfaces that may be hot.

3. Unplug from outlet when not in use prior to installing or removing
parts and before cleaning. Allow for the device to cool rst before
handling.

4. To protect against the risk of electrical shock, do not immerse the
appliance, cord or plug in water, or other liquids.

WARNING AVERTISSEMENT

Electrical Shock Hazard

Keep water an d other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an el ectrical sho ck.

Do not spray w ater or cleaning
products. Liquid could contact
the electrical components
and cause a s hort circuit o r an
elect rical shock. Do n ot use unit
if power cor d is damaged or has
been modied.

5. DO NOT operate this device or any other electrical equipment
with a damaged cord or plug, or after the unit malfunctions,
is dropped or damaged in any manner. Return to the nearest
WINCO Authorized Service Center for examination, repair and/or
adjustment.

6. The use of accessory attachments not recommended by WINCO
may cause re, electric shock or injury.

Risque de choc électrique

Conser ver l'eau et d'autres liqui des
de pénétr er à l'intérieur de l'app areil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.

Ne pas pulvé riser de l'eau ou des pro duits
de nettoyage. Le liquide pourrait contacter
avec les comp osants élec triques et caus er
un court- circuit ou un cho c électrique.
Ne pas util iser l'appareil si le cor don
d'alimentation est endommagé.
ou a été modi é.

WARNING AVERTISSEMENT

Fire Hazard.

Correct installation precautions,
procedures and regulations
must be fo llowed. Operati on
and safe ty training is ne cessary
for all use rs of this equipme nt.

7. Not intended for outdoor installation.

8. DO NOT let the cord hang over the edge of a table or counter,
or touch hot surfaces.

9. DO NOT place on or near a hot gas or electric burner, or in a
heated oven.

10. This appliance should always be on a stable and steady countertop
or table. Allow sucient space around the cooking area. Never use
the unit on/near low-heat-resistant materials (carpet, vinyl).

Risque d'incendie

La surcha ue des vapeurs d' huile ou de
l'huile peut s'enammer et provoquer
un incendi e. Surveillez la temp érature,
la qualité et l e niveau d’huile. Uti lisez et
entrete nez le système d'élimi nation des
vapeurs d'huile.

11. This appliance is not intended for use by individuals (including
children) with reduced or impaired physical, sensory or mental
capabilities, or lack of experience or knowledge, unless they have
been given proper supervision or instruction concerning the use of
this appliance by a person responsible for their safety.

12. Do not place any object between the pot/pan and the glass
surface of the unit.

13. DO NOT cook on a broken cooktop – if the cooktop should break,
cleaning solutions and spillovers may penetrate the broken or
damaged surface and create a risk of electrical shock.

14. Clean the cooktop with caution – if a wet sponge or cloth is used
to wipe spills on a hot cooking surface, exercise caution to avoid
steam burns. NOTE: some cleaners may produce noxious ames
when applied to a hot surface.

15. DO NOT place metal objects such as knives, forks, spoons and lids
on the glass surface, as they can get very hot.

16. Items with a magnetic eld, including radios, televisions,
automatic banking cards and cassette tapes, may aect the
functioning of the unit.

17. It is not recommended to heat pots/pans when empty. Pots/Pans
will heat extremely quick.

18. If an extension cord power-supply is used,
a. The marked electrical rating of the extension cord should be

rated the same or greater than the electrical rating of the unit.

b. The cord should be located so that it will not drape over the

countertop or tabletop where it can be damaged or moved
unintentionally.

NOTE:

Use of an adapter is not permitted in Canada.

SAVE THESE INSTRUCTIONS

Proper Grounding · Mise à la terre correcte

This machine is provided with a three-pronged
grounding plug. The outlet to which this plug
is connected must be proper ly grounded. If the
receptacle is not the proper grounding type, cont act
an electrician. DO NOT, under any circums tances, cut
or remove the thir d ground prong from the power cord
or use any adapter plug.

Cette machine est équip ée d'une che à trois broches.
La prise sur laquelle cette che es t branchée doit être
correctement mise à la terre. Si la prise n'est pas le type
de mise à la terre, contactez avec un électric ien. NE PAS,
en aucun cas couper ou enlever la troisiè me broche de
terre à partir du cordon d'al imentation ou utiliser un
adaptateur.

USE A GROUNDED OUTLE T
DO NOT ADD AN ADAPTO R

TO THE PLUG

UTILISER UNE PRISE AVEC MI SE
À LA TERRE NE PAS AJO UTER UN

ADAPTATEUR SUR LA FICHE

4

Consignes de sécurité importantes

Ces instructions doivent être suivies en tout temps. Le non-respect de
ces instructions peut entraîner des blessures sur vous-même ou sur
d'autres personnes.

LORSQUE VOUS UTILISEZ DES APPAREILS ÉLECTRIQUES,
DES PRÉCAUTIONS ÉLÉMENTAIRES DE SÉCURITÉ ET DE BON
SENS DOIVENT ÊTRE OBSERVÉES, Y COMPRISMAIS PAS
SEULEMENTÀ CE QUI SUIT :

1. Lire toutes les instructions. N'utilisez cet appareil que pour l’usage
auquel il est prévu.

2. NE PAS TOUCHER les surfaces qui peuvent être chaudes – veillez à
toujours utiliser les poignées ou boutons.

3. Débranchez l’appareil: quand hors service; avant d'installer ou de
retirer des pièces; avant le nettoyage. Laissez l'appareil refroidir
d'abord.

4. Pour vous protéger contre tout risque de choc électrique, ne
plongez pas l'appareil, le cordon ou la prise dans l'eau ou dans
d’autres liquides.

WARNING

Electrical Shock Hazard

Keep water an d other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an el ectrical sho ck.

Do not spray w ater or cleaning
products. Liquid could contact
the electrical components
and cause a s hort circuit o r an
elect rical shock. Do n ot use unit
if power cor d is damaged or has
been modied.

AVERTISSEMENT

Risque de choc électrique

Conser ver l'eau et d'autres liqui des
de pénétr er à l'intérieur de l'app areil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.

Ne pas pulvé riser de l'eau ou des pro duits
de nettoyage. Le liquide pourrait contacter
avec les comp osants élec triques et caus er
un court- circuit ou un cho c électrique.
Ne pas util iser l'appareil si le cor don
d'alimentation est endommagé.
ou a été modi é.

5. NE PAS UTILISER cet appareil ou tout autre équipement électrique
dont le cordon ou la che sont endommagés, ou si l'appareil
fonctionne mal, est tombé ou est endommagé de quelque
manière. Retournez l’appareil au centre de service autorisé WINCO
le plus proche pour examen, réparation et/ou réglage.

6. L'utilisation d'accessoires non recommandés par WINCO peut
provoquer incendie, électrocution ou blessures.

7. Non prévu pour une installation en extérieur.

8. NE PAS LAISSER le cordon pendre au bord d'une table ou d’un
comptoir, ou toucher des surfaces chaudes.

9. NE PAS PLACER sur ou près d'un brûleur à gaz ou électrique, ou
dans un four chaué.

10. Cet appareil doit toujours se trouver sur une table ou un plan de
travail stable et régulier. Laissez susamment d’espace autour de
la zone de cuisson. N’utilisez jamais l’appareil sur des matériaux de
faible résistance à la chaleur (tapis ou du vinyle).

11. Cet appareil n'est pas destiné à être utilisé par des personnes
(enfants y compris) aux capacités physiques, sensorielles ou
mentales réduites, ou ne bénéciant pas de l’expérience ou du
savoir nécessaires à son utilisation, à moins qu'elles aient reçu
un encadrement ou une formation adéquats par une personne
responsable de leur sécurité.

12. Ne placez aucun objet entre la casserole ou la poêle et la surface
de verre de l’appareil.

13. NE PAS CUISINER sur un plan de travail ssuré – si tel est le cas, les
produits de nettoyage et les débordements peuvent pénétrer la
surface cassée ou endommagée et créer un risque d’électrocution.

14. Nettoyer la plaque de cuisson avec précaution – si une éponge
ou un chion humide est utilisé pour essuyer les déversements
sur une surface de cuisson chaude, faire preuve de prudence
pour éviter les brûlures de vapeur. Certains nettoyants peuvent
produire des ammes toxiques lorsqu’ils sont appliqués sur une
surface chaude.

15. NE PLACER AUCUN objet métallique tels que couteaux, fourchettes,
cuillères et couvercles sur la surface de verre, car ils peuvent
devenir chauds.

16. Les objets magnétiques, y compris radios, télévisions, cartes
bancaires automatiques et cassettes vidéo peuvent aecter le
fonctionnement de l'appareil.

17. Il n'est pas recommandé de réchauer les casseroles/poêles vides.
Les casseroles/poêles chauent très rapidement.

18. Si un cordon/rallonge d’alimentation est utilisé(e),
a. la puissance électrique indiquée sur la rallonge doit être au

moins aussi élevée que la puissance de l’appareil.

b. le cordon doit être disposé de manière à ne pas reposer sur le

comptoir ou sur la table sous peine d’être endommagé ou retiré
involontairement.

MISE EN gARdE : AVANT d'uTIlISER uN AdApTATEuR, Il fAuT
déTERMINER quE lA VIS SuR lA pRISE EST coRREcTEMENT
MISE à lA TERRE. EN cAS dE douTE, coNSulTEz uN
élEcTRIcIEN.

SûR qu’Il EST coRREcTEMENT RElIé à lA TERRE.

N’uTIlISEz jAMAIS uN AdApTATEuR, SAuf SI VouS êTES

REMARQUE :

L’utilisation d'un adaptateur n'est pas autorisée au
Canada.

CONSERVEZ CES INSTRUCTIONS

5

Operation

Note

Your WINCO® Commercial Induction Cooker defaults
to the power setting, shown in wattage. To view the
temperature setting in Fahrenheit, press the "TEMP"
button. Each time the unit is plugged in, it will
default to the power setting for that unit:

EIC-400/1300W and EIC-400B/1600W. To change
this, press the up or down arrows in the power or
temperature setting.

PARTS

1. Heat Mode Setting (Wattage)

2. Temperature Mode Setting (°C / °F)

3. Timer Mode Setting (Mins)

4. LED Display

5. Adjustment Control for Temperature/Heat/Timer

6. On/O Power Button

7. Stainless Steel Housing

8. Schott™ Ceramic Glass Cooking Surface

Note

Induction range requires induction ready cookware.

Compatible pans include at-bottom pans and/or pots with a
diameter of 4.75 –10 inches, made of steel, cast iron, enameled
iron, or stainless steel – please check with the pan manufacturer to
conrm induction compatibility.

If the pan is not induction ready, it will not register on the induction
range. The LED display will show “-----“ ashing when attempting
to select a heat mode without an induction ready pan on the glass
cooking surface.

The unit will automatically shut o after 10 seconds of not having an
induction ready pan on it.

1. Before turning on the power, ensure that your cookware is on
the ceramic cooking surface. This induction range is equipped
with small-object detection capability, which will prevent it from
operating unless you have an appropriately sized induction ready
pan in place.

2. To turn the power on, press the ON/OFF button and choose a
cooking mode by pressing the HEAT or TEMP buttons. The unit will
default to Heat mode (EIC-400 to 1300W or EIC-400B to 1600W),
when turned on.

a. The HEAT button allows you to choose how many watts of

power to cook with.

1

2

3

4

5

b. The TEMP button allows you to choose the temperature at which

to cook.

3. Once a cooking mode has been chosen, use the UP and DOWN
buttons to set the desired wattage or temperature.

4. The unit will operate continuously for up to 2.5 hours, after which
time the unit will automatically shut down for safety. If you wish to
continue, press the On/O Button to restart the unit.

8

7

6

Choosing Fahrenheit or Celsius

Unit will automatically default to °F once plugged in.

In TEMP mode, you can choose Fahrenheit (°F) or Celsius (°C). When the
unit is plugged in and in the OFF position, the LED screen will be blank.
Press and hold the TEMP button for three seconds. The screen will
illuminate and display °C or °F. The current setting will blink.
Use the UP buttons to switch to your desired setting. Once your desired
setting is blinking, press the TEMP button to conrm and then press
ON/OFF to start.

Setting the Timer

1. Turn the unit on and choose your cooking mode by pressing TEMP
or HEAT.

2. Press the TIMER button and use the UP and DOWN buttons to
adjust time anywhere from 1 minute to 150 minutes (2.5 hours).
Once the timer display switches back to Cooking Mode, the timer
will begin to count down, and the LED next to the ‘Timer(Min)’ will
remain lit.

3. When the time has counted down to “0” the unit will beep once
and then shut down.

4. Please note that the maximum cooking time is 150 minutes. If
the unit is on for 10 minutes prior to setting the timer, the max
allowable timer is 140 minutes. To reset to the maximum time
allowable, turn the unit o and back on with the On/O button.

6

Cleaning, Care & Maintenance

Service and Repair

To maintain the appearance and increase the service life, clean
the unit and glass surface after each day’s operation. However,
you may determine that the unit requires more frequent cleaning
depending on the volume of production.

ALWAYS unplug the unit after every use, before cleaning and when
not in operation. The exterior of the unit may be cleaned by carefully
wiping with a damp cloth.

There are no user-serviceable parts within this appliance. Do not
remove any components or service panels on this product. To avoid
serious injury or damage, NEVER attempt to repair the unit
or replace a damaged power cord yourself. Contact a WINCO® Approved
Service Technician to make repairs.

To initiate warranty service contact: [e-mail]
or call: 973-295-3899

DO clean the cooking surface while the unit is slightly warm with
warm & soapy water. DO NOT use cold water on a warm/hot surface.

NEVER submerge the device completely in/under water. DO NOT clean
with a water jet.

WARNING:

The cooking surface will

DO NOT send unit to WINCO® without rst contacting our customer
service department.

See "Limited Warranty" section on page 8 for details.

be hot after use. Exercise caution when
handling cooking utensils and cookware.

HOT

Troubleshooting

Before placing a service call, please refer to the below chart in the event of the following LED display error codes.

ERROR CODE DESCRIPTION OF ERROR RECOMMENDED SOLUTION

EIC-400 EIC-400B

There is no cookware or no suitable cookware on the

“---“ shows on display and the unit

beeps

E1 E01

E2 E02

E3 E03 The accessory and spare parts are damaged

E5 E05 The heater is damaged

E6 E06

E7 E07

E08

E9

EE Unit has reached maximum cooking time Press On/O Button to restart the unit.

range. The power will shut o within 10 seconds if there
is no cookware detected, or the wrong type of cookware
is on the unit.

EIC-400 voltage is under 75V

EIC-400B voltage is under 145V

EIC-400 voltage is over 143V

EIC-400B voltage is over 275V

The temperature sensor underneath cooking area is
defective, thermal protection has shut the unit o due
to overheating

The cooking temperature inside the unit is too hot Unplug the unit and let it cool for at least 20 minutes. Once the

The temperature sensor underneath cooking area is
defective

Malfunction has been activated or triggered Unplug the unit. Plug the unit back in and continue use. If the

Check power cord

Make sure your pot/pan is induction-compatible.

Check diameter of the pot/pan. It must have a at bottom that is
between 4.75” and 10” diameter.

Check electrical specications of power source.

Contact WINCO

Unplug the unit and let it cool. Plug the unit back in and continue
use. If the range still does not function, contact WINCO.

range has completely cooled down, position it away from the wall
& ensure there are no obstructions to airow. Plug the unit back
in and continue use.

Unplug the unit and let it cool. Plug the unit back in and continue
use. If the range still does not function, contact WINCO.

range still does not function, contact WINCO.

7

Limited Warranty

WINCO warrants to the original purchaser of new equipment that said
equipment, when installed in accordance with our instructions within
North America and subjected to normal use, is free from defects in
material or workmanship for a period of 1 year. The labor warranty is
one year from original installation or 18 months from actual factory
shipment date, whichever date occurs rst.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE.

WINCO’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY
IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING
EQUIPMENT THAT PROVES TO BE DEFECTIVE IN MATERIAL OR
WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.

IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY,
INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY,
PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER
ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES,
WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR
OTHERWISE.

This warranty is given only to the rst purchaser from a retail dealer.
No warranty is given to subsequent transferees.

Warranty does not cover product failures caused by: failure to
maintain, neglect, abuse, damage due to excess water, re, normal
wear, improper set up and use. Periodic maintenance is not covered.

REGISTER ONLINE AT:

http://support.wincous.com

Proof of purchase is required to extend warranty more than 1 year
from date of shipment from the factory.

THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE
AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER.
WINCO NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS
TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN
CONNECTION WITH SAID EQUIPMENT.

Examples of items not covered under warranty, but not limited to just
these items:

1. Acts of God, re, water damage, burglary, accident, theft.

2. Freight damage.

3. Improper installation or alteration of equipment.

4. Use of generic or after market parts.

5. Repairs made by anyone other than a WINCO designated
service provider.

6. Lubrication.

7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.

8. Cleaning of equipment.

9. Misuse or abuse.

WARRANTY REGISTRATION

This warranty is not in force until such time as a properly completed
and digitally signed Installation/Warranty Registration has been
received by WINCO within 30 days from the date of installation.

WARRANTY SERVICE

To initiate warranty service contact: [e-mail]
or call: 973-295-3899

DO NOT send unit to WINCO without rst contacting our customer
service department.

Please keep this manual in a safe place for future use!

8

SCAN THE QR CODE WITH YOUR MOBILE DEVICE

or go to

http://support.wincous.com

TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.