Page 1 of 8
14. SAVE THESE INSTRUCTIONS for future reference and training.
557X-558X
XL Cozy Comfort & XL Cozy Comfort Swing-Arm, Premier Recliner
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
before attempting to use this product; otherwise injury may occur.
557X-558X Weight Capacity = 350 lbs. (159 kg)
In all cases the labeling on the chair at the time of delivery is the correct rating for your chair and that weight rating should not be exceeded.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
Winco assumes no responsibility for damage or injury caused by the improper assembly, installation
Failure to correctly install clevis pins connecting Back Frame fork holes and Seat Frame
the chair and void warranty.
Comfort Care & Cozy Comfor t , P r e m ier Recliner
567X-5680
CUSTOMER INSTRUCTIONS
If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-3377
or use of these products; or during assembly or maintenance of these products.
1. READ AND FOLLOW ALL DIRECTIONS.
2. DO NOT put hands, feet or clothing into any openings when changing positions on recliner. Attendant MUST
confirm that users hands and feet are safe while changing recliner positions or INJURY MAY RESULT.
3. Stay clear of the recline mechanisms.
4. Periodically, recheck tightness of all nuts, bolts and screws.
5. NEVER use the side-tables or chair arms or backrest or legrest as a seat; SERIOUS INJURY MAY OCCUR.
6. Chair MUST be in full upright position with casters locked when a patient enters or exits chair.
7. 5570 ONLY - NEVER allow a patient to exit a reclined chair with position-lock engaged or SERIOUS INJURY MAY
OCCUR.
8. Lock casters at all times, except when transporting chair.
9. Chair must ALWAYS be positioned on a level surf ace .
10. DO NOT use recliner for Transporting in or with ANY type of vehicle or trailer. Winco recliners have not been
tested or approved for use by an occupant in any type of vehicle or trailer.
11. Immediately remove from service; Any recliner with broken recline mechanisms, torn upholstery, or other
mechanical or visible damage.
12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
13. NEVER EXCEED the recommended weight capacity of 350 lbs. (159 kg.)
ALWAYS REFER TO THE WEIGHT CAPACITY LABEL ON YOUR CHAIR.
567X Weight Capacity = 450lbs. (204 kg)
NO TOOLS REQUIRED FOR ASSEMBLY!
Install the Back:
1. After checking your product for any shipping damage, chair needs to be positioned upright on level surface.
Remove all packing material and hardware that was secured for shipping. Remove tape and plastic. If using
scissors or knife, please be careful not to damage upholstery.
2. Make sure footrest is in closed position & LOCK ALL CASTERS before installing chair back.
3. Remove the (2) Bow Tie Cotter Pins and the (2) Clevis Pins from the lower Back Frame Forks. DO NOT
LOSE THESE PARTS, YOU WILL NEED THEM AGAIN!
4. Using a second person to help; Position the Back Frame Forks over the Seat Frame and align holes.
HINT: If you do not have a helper; Rest the bottom of the Upholstered Back on the rear portion of the Upholstered Seat and
push the Back Assembly slightly forward to he lp stea dy the chair bac k.
Rail holes, will cause back to operate poorly and may cause injury to the user or damage
006325 Rev. I Date 06-27-13 JWC
Page 2 of 8
WARNING: Attendant must release Position Lock before patient can exit chair – If patient attempts
Periodically recheck tightness of all screws and bolts, and never use the chair arms, backrest, legrest or
tray as a seat.
FIG.1
FIG.2
Back Support
Strut
Angled
Bracket
Seat
Frame
Back Frame
Forks
5. Use (1) one of the Clevis Pins and insert it FROM the inside of Back Frame Fork, THROUGH hole in Seat
Frame and, THROUGH outside of Back Frame Fork.
REPEAT FOR OPPOSITE SIDE OF CHAIR. (FIG.2)
6. Insert (2) Bow Tie Cotter Pins, into the small holes on ends of the (2) Clevis Pins you just installed. (FIG.1)
7. Remove the Bow Tie Cotter Pin and the Clevis Pin from the Back Support Strut (attached to back frame).
8. Align the holes of the Back Support Strut with the holes in the Angle Brackets and insert the Clevis Pin into
these aligned holes and secure with the Bow Tie Cotter Pin.
Operation of the Chair:
1. NON-RESTRAINT (5570 only): To make the chair per manently non-restraint, u nbolt the Position Lock Bar
from the back of the chair.
2. The 5570, 5580, & 5670 recliners have three (3) positions; U PRIGHT, SEMI-R ECLINE, an d RECLINE, which
can be achieved by user or attendant. 5570 Only: The pos ition lock bar can only be engaged or diseng aged
by attendant. Not all notches on Position Lock Bar are used for this model chair.
3. POSITION LOCK (55 70 only): Attendant may hold the c hair in a reclined position by enga ging the Position
Lock. To safely accomplish this, recline the chair to the 2
nd
or 3rd rec line position and lower the pos ition lock
with your hand until the notches on the Position Lock bars engage with the Position Lock Pins.
To release Position Lock, raise the Position Lock off of the Pins and return chair to upright position.
to exit chair with Position Lock engaged, SERIOUS INJURY MAY RESULT.
WARNING: Failure to release the Position Lock before changing p o sitions will result in damage to
the chair and void the warranty.
4. This chair is equipped with (4) Twin-wheel locking casters.
Twin-wheel locking casters (3" BLACK casters only) will lock wheel but will NOT prevent wheel from
swiveling. To lock, push down on the wheel tab.
NOTE:
All 3" BLACK casters are wheel locking ONLY. They DO NOT have a TOTAL and DIRECTIONAL lock feature.
To ensure proper operation of the reclining mechanism, lubricate all pivot points with a silicone type lubricant (or lubricant
approved by your facility) at least twice yearly. Periodically recheck tightness of all screws and bolts.
Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Winco chair. This is normal. Please allow 1-2
weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original appearance
006325 Rev. I Date 06-27-13 JWC
Swing-arm Operation: (For Model: 5680 only)
IV Pole
Contoured Headrest
CH00
Torso Support
TS00
Side Cushion
SC00
FIG.4
FIG.5
FIG.3
A
1. To open, push the red latch handle to unlock the
swing-arm.
2. To close, push swing-arm toward latch until latch
engages.
Operating Instructi ons for Table OPTIONS availabl e for your recliner:
To position side-tables
1. To raise table, grasp center of table and gently raise into place.
Table will automatically lock into place when released.
2. To lower table, grasp table at the center, raise and pivot down in
one movement.
“Lap Position”
1. To place pivot-table in “lap” position, pivot the table away
from chair and pull over lap. (FIG.5)
2. Tighten star-knob to secure the pivot-table in the lap position
“Exit” Position
1. With the table in the “lap” position, loosen star-knob & push
table away to exit chair.
Remove Pivot-Table
1. Loosen pivot-table star knob.
2. Pull up on pivot-table until the table stem comes out of the
black bracket.
006325 Rev. I Date 06-27-13 JWC
(FIG. 3A)
(FIG. 3)
IV
*Side-Table (LT, RT, DT)
*Pivot Table (NP, PN)
Other available Options:
(FIG.4)
Page 3 of 8
HEAT & MASSAGE OPTIONS
HEAT
MASSAGE
-OR-
HEAT ONLY
NOTE:
Control is located on the inside of right arm of chair.
Heating:
3 Lights
2 Lights
1 Lights
No Light
Allow 5-8 minutes for back and seat to warm to desired TEMP. setting.
Heat will automatically shut off after approximately 60 minutes.
(Timer resets when switch is pressed)
Massage (optional):
1X
2X
3X
4X
5X
6X
Massage will automatically shut off after approximately 15 minutes. (Timer resets when switch is pressed)
CORD STORAGE
(Models with Heat-HT or Heat & Massage-HM)
1. Before transporting chair, or when heat & massage is
not in use, power cord should be coiled and stored in
the "Hook & Loop" fastener provided as shown, to
prevent tripping on cord, damage to cord, damage to recliner, etc.
006325 Rev. I Date 06-27-13 JWC
Push
= High Heat
= Medium Heat
= Low Heat
= HEAT OFF
= Lower Back / Low Intensity
= Lower Back / High Intensity
= Upper & Lower Back / Low Intensity
= Upper & Lower Back / High Intensity
= Alternating Upper & Lower Back / High Intensity
= MASSAGE OFF
Use a DAMP CLOTH ONLY to clean switch, wiring or power pack (located under seat frame).
•
If there is no heat or massage or flashing light on switch - check power cord connections to wall outlet AND
•
connection of power cord to power pack unit under chair.
If switch displays a flashing light; Check all accessible wire connectors under chair for possible loose
•
connections, then contact Winco customer service: 1-800-237-3377.
Operating Instructi ons f or HM or HT Opti on:
(Models with Heat-HT or Heat & Massage-HM)
-
button – See indicator light on switch
HEAT
Push
MASSAGE
button
Page 4 of 8
Keep cord CLEAR of any moving parts
Page 5 of 8
FOR PRODUCTS WITH POWERED OPTIONS (Heat, Massage, etc...)
Read all instructions before using this product.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock when using an electrical appliance, basic precautions should always
be followed, including the followi n g :
DANGER - Always unplug this product from the electrical outlet before cleaning, maintenance or when putting on or taking
off parts.
WARNING:
1. Unplug this product from the electrical outlet if this product is not to be used for extended periods of time.
2. Supervision should be provided when this product is used by, on, or near children, invalids, or disabled persons.
3. Use this product only for its intended use as described in this manual. Do not use attachments not recommended
by the manufacturer.
4. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the product to an authorized Winco service center.
5. DO NOT carry or pull this product by power supply cord or use the cord as a handle.
6. Keep the cord away from heated surfaces.
7. Do not use outdoors.
8. To disconnect, turn all controls to the "off" position, then remove plug from outlet. Do not "yank" cord.
9. Clean switch with a damp cloth only – Warranty will be VOID if liquid is introduced into sw itch mech ani sm.
10. Use only a certified extension cord that is rated at 15 amperes; extension cords rated for less amperage may
over heat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over.
11. DO NOT run recliner or other equipment over cord.
12. Recliner comes with a grounded three blade plug, if the plug does not fit into the outlet; contact a certified
electrician to install the proper outlet. DO NOT MODIFY THE PLUG IN ANY WAY.
DANGER:
i) Never insert pins, or attach other metallic fasteners into/onto the upholstery of this chair.
ii) Do not use this product if the covering shows signs of deterioration, such as checking, blistering, or cracking.
iii) KEEP DRY - Do not operate in a wet condition or environment.
WARNING:
i) Long term, continuous exposure to heat may cause burns. It is recommended that skin in contact with heated area be
checked for redness and blistering during long term usage. Do not use on an infant, invalid or unconscious person. Do not
use on insensitive skin or on a person with poor blood circulation. If you are uncertain if you should use this product, ple a se
consult your physician about the use of heat and massage.
ii) Do Not Crush/Pinch heating elements or wiring.
WARNING: Connect this product to a properly grounded outlet only.
GROUNDING INSTRUCTIONS:
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-gro und ing con duc tor
and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug
provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug. Make sure that the product is connected to an
outlet having the same configuration as the plug. No adapter should be used with this product.
For an added level of safety; Winco recommends the use of a 120 volt GFCI (ground fault circuit interrupter) outlet.
006325 Rev. I Date 06-27-13 JWC
Page 6 of 8
Products with the following markings are intended for commercial use only.
Visit our website www.wincomfg.com/product-documents/parts-lists for a complete parts list catalog of your chair or
call Customer Service @ 1-800-237-3377 to request it by mail.
006325 Rev. I Date 06-27-13 JWC
Page 7 of 8
Other Quality Winco Medical Furnishings You May Be Interested In:
Visit us online at www.wincomfg.com
006325 Rev. I Date 06-27-13 JWC
Page 8 of 8
Design, appearance, parts, & construction are subject to change without notice
006325 Rev. I Date 06-27-13 JWC
Loading...