Winco 529S User Manual
Page 1 of 4
5291-529S
XL Convalescent Recliner
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-33 77
before attempting to use this product; otherwise injury may occur.
CUSTOMER INSTRUCTIONS
Winco assumes no responsibility for damage or injury caused by the improper assembly, installation
or use of these products; or during assembly or maintenance of these products.
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER use tray as a restraint.
3. DO NOT put hands, feet or clothing into any openings when changing recliner positions. Attendant MUST confirm
that users hands & feet are clear of moving parts when changing recliner positions or INJURY MAY RESULT.
4. Stay clear of the recline mechanisms.
5. Periodically, recheck tightness of all nuts, bolts and screws.
6. NEVER use the trays or chair arms or backrest or legrest as a seat; SERIOUS INJURY MAY OCCUR.
7. Chair MUST be in full upright position with casters locked when a patient enters or exits chair.
8. NEVER allow a patient to exit a reclined chair with position-lock engaged or SERIOUS INJURY MAY RESULT
9. Lock casters at all times, except when transporting chair.
10. Chair must ALWAYS be positioned on a level surface.
11. DO NOT use recliner for Transporting in or with ANY type of vehicle or trailer. Winco recliners have not been
tested or approved for use by an occupant in any type of vehicle or trailer.
12. Immediately remove from service; Any recliner with broken recline mechanisms, torn upholstery, or other
mechanical or visible damage.
13. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
14. NEVER EXCEED the recommended weight capacity of 450 lbs. (204.1 kg).
15. SAVE THESE INSTRUCTIONS for future reference and training.
DO NOT
THIS COULD CAUSE INJURY TO USER OR DAMAGE TO THE RECLINE MECHANISM AND WILL VOID WARRANTY.
LIFT OR CHANGE CHAIR POSITION BY USING THE LEGREST.
ALWAYS CHANGE POSITION FROM BACK OF CHAIR.
5291-529S XL Weight Capacity = 450 lbs. (204.1kg)
Tools needed for assembly:
Scissors to aid in removal of packing material
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
Install the Back:
1. After checking your product for any shipping damage, chair needs to be positioned upright on level surface.
Remove all packing material and hardware that was secured for shipping. Cut tape and plastic with scissors,
being careful not to damage upholstery.
2. Make sure footrest is in closed position & LOCK ALL CASTERS before installing chair back.
3. Remove the (2) Bow Tie Cotter Pins and the (2) Clevis Pins from the lower Back Frame Forks. DO NOT
LOSE THESE PARTS, YOU WILL NEED THEM AGAIN.
006100 Rev R Date 11-08-11 JWC
Page 2 of 4
4. Using a second person to help; Position the Back Frame Forks over the Seat Frame and align holes.
HINT: If you do not have a helper; Rest the bottom of the Upholstered Back on the rear portion of the Upholstered
Seat and push the Back Assembly slightly forward to help steady the chair back.
Failure to correctly install clevis pins connecting Back Frame fork holes and Seat Frame Rail ho les, will cause back
to operate poorly and may cause injury to the user or damage the chair and void warranty.
5. Use (1) one of the Clevis Pins and insert it FROM the inside of Back Frame Fork, THROUGH hole in Seat
Frame and, THROUGH outside of Back Frame Fork. REPEAT FOR OPPOSITE SIDE OF CHAIR. (FIG.2)
6. Insert (2) Bow Tie Cotter Pins, into the small holes on ends of the (2) Clevis Pins you just installed. (FIG.1)
7. Remove the Bow Tie Cotter Pins and the Clevis Pins from the Back Support Struts (attached to
backframe).
8. Align the holes of the Back Support Strut with the holes in the seat frame Angled Bracket and insert the
Clevis Pins into these aligned holes and secure with the Bow Tie Cotter Pin. (FIG.2)
Back Frame
Forks
Seat
Frame
FIG.1
REAR of Chair
FIG.2
Back Support
Strut
Angled
Bracket
006100 Rev R Date 11-08-11 JWC
Loading...