Winco 5111 User Manual

5101-5111

Golden Years Chair

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-33 77

before attempting to use this product; otherwise injury may occur.

Winco assumes no responsibility for damage or injury caused by improper assembly,

installation, use, or maintenance of these products.

CUSTOMER INSTRUCTIONS

1. READ AND FOLLOW ALL DIRECTIONS.

2. NEVER use tray as a restraint.

3. ALWAYS fold footplate up before user enters or exits the chair; otherwise INJURY MAY RESULT.

4. DO NOT stand on plastic footplate; INJURY MAY RESULT.

5. Keep users hands and feet clear of any moving parts. Attendant MUST confirm that users hands and feet are clear
of moving parts when adjusting positions on tray or footrest or INJURY MAY RESULT.

6. Never use the chair arms or tray as a seat; INJURY MAY OCCUR.

7. Lock casters at all times, except when transporting chair.

8. Chair must ALWAYS be positioned on a level surface.

9. DO NOT use chair for Transporting in or with ANY type of vehicle or trailer. Winco chairs have not been tested or
approved for use by an occupant in any type of vehicle or trailer.

10. Immediately remove from service; Any chair with broken parts, torn upholstery, or other mechanical or visible
damage.

11. Periodically, recheck tightness of all nuts, bolts and screws.

12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.

13. NEVER EXCEED the recommended weight capacity of 275 lbs. (124.7 kg).

14. SAVE THESE INSTRUCTIONS for future reference and training.

Page 1 of 4

5101-5111 Weight Capacity = 275 lbs. (124.7 kg.)

Tools needed:

 Slot-head screwdriver OR, 5/16” wrench (multiple size wrench included)
 Scissors or box cutter to aid in removal of packing material
 Always start hardware together by hand first - Use of powered tools not recommended

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

Install the Back:

1. After checking your product for any shipping damage, chair needs to be positioned upright on level surface.
Remove all packing material and hardware that was secured for shipping. Cut tape and plastic with
scissors, being careful not to damage upholstery.

2. Use a standard slot-head screwdriver or 5/16” wrench; Remove the (2) screws that have been pre-installed
in the Seat Frame Rails. DO NOT discard screws.

3. To ease assembly, spray the Seat Frame Rail ends with WD-40 (or similar lubricant approved by your
facility).

006085 Rev L Date 11-08-11 JWC

Page 2 of 4

4. Slip the Back Frame over the Seat Frame Rail ends until the holes in Back Frame line up with the holes in
the Seat Frame Rails.

5. Insert the (2) screws you removed in step 2, into the aligned holes of the Back Frame and Seat Frame.

6. Tighten these screws firmly. Failure to install these screws MAY RESULT IN SERIOUS INJURY.

Operation of the Tray: 5101 ONLY

7. Tray Arms are inserted into the Tray Receiving Tubes (under Armrests on chair). The Tray automatically
locks into the first position, depress the Snap Button (on Right Tray Arm) for 2 more positions.

NOTE: Left and right; As if you are seated in chair.

8. The Right Tray Arm is movable to compensate for minor variations in the width of the chair.

9. Storing the Tray; Insert the LEFT tray arm tube INTO the RIGHT tray receiving tube and the Latch Button
will lock it into place. Allow the right side of the table to hang down vertically on the right side of chair (Left &
Right; as if you are seated in chair).

10. To make the tray permanently “non-restraint”, remove the Snap Button of the Right Tray Arm.

Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Win co chair. This is normal.
Please allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original
appearance.

Periodically recheck tightness of all screw and bolts, and never use the chair arms or tray as a seat or the

tray as a restraint.

Visit our website www.wincomfg.com/product-documents/parts-lists for a complete part s list catalog of your chair or

call Customer Service @ 1-800-237-3377 to request it by mail

006085 Rev L Date 11-08-11 JWC