Winco 3659 User Manual

363-364-365

Aluminum Panel Privacy Screens

Page 1 of 4

CUSTOMER INSTRUCTIONS

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-33 77

before attempting to use this product; otherwise injury may occur.

Winco assumes no responsibility for damage or injury caused by improper assembly,

installation, use, or maintenance of these products.

1. READ AND FOLLOW ALL DIRECTIONS.

2. NEVER place screen on a cart, table, stand or other objects; Screen could fall and INJURY MAY OCCUR.

3. NEVER place screen near open flame or over a radiator or heat register.

4. NEVER place screen in front of a door or exit sign; or during emergency screen could hinder evacuati on.

5. SUFFOCATION DANGER to children if vinyl is not attached to screen. VINYL SCREEN IS NOT A TOY.

6. DO NOT allow children to play with screen; Screen could fall and INJURY MAY OCCUR.

7. Screen should ALWAYS be positioned on level surface.

8. NEVER stand or ride on screen legs; INJURY MAY OCCUR.

9. DO NOT attach object to screen frame; Screen can tip over and INJURY MAY OCCUR.

10. Remove from service, any screen with broken or missing parts, torn vinyl, or other visible damage.

11. SAVE THESE INSTRUCTIONS for future reference and training.

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

After checking your product for any shipping damage, remove all packing material and h ard ware that was secured for
shipping. Cut tape and/or plastic with scissors, being careful not to damage screen.

ASSEMBLY INSTRUCTIONS FOLDING SCREENS

1. Install Wing Legs on Wing Frames (FIG.1) using 3/16" x 2" bolts and tighte n nuts. Using 3/16" x 1" bolts install Mid Legs
on Mid Frame and tighten nuts.

The 4-panel screen has 2 Wing Frames and 2 Mid Frames. The 5-panel screen has 3 Wing Frames and 2 Mid Frames. (FIG.2)

363 364 365

2. Check screen for levelness, if necessary the legs can be gently bent so that all legs touch the floor.

3. To clean or replace Vinyl Panels, grasp panel rod at end a way from Spring Retainer Clip and slide rod towards clip.

This will release rod from frame.

006290 Rev G Date 07-23-12 JWC

Wing Leg

Mid Leg

NOTE:

FIG.1

FIG.2

Page 2 of 4

PANEL REPLACEMENT

4. To replace Vinyl Panels, grasp Screen Rod; Screen Rod is spring-loaded and can b e moved toward end with spring.
Push & pull the Screen Rod to determine which way will compress the spring and a llow removal of the Screen Rod
and Vinyl Panel. (SEE PHOTO OF ROD ENDS, BELOW)

5. Re-install the Screen Rod by reversing the above procedure.

CARE & MAINTENANCE OF YOUR SCREEN

6. Periodically check all fasteners for tightness.

7. To clean Vinyl Panels use only mild liquid soap and water.

Wrinkles in Vinyl – Storage and shipping causes wrinkles of the vinyl of your Winco Screen; This is normal. Pleas e allo w 1-2

weeks at room temperature (approx. 70+ degrees) to allow for vinyl to return to original appearance.

364 shown

Parts List: Qty.

(1) Complete Frame
For 363 1
For 364 1
For 365 1
(2) Mid Leg for Model 363 2
For Models 364 & 365 4

(3) Wing Leg for Model 363 4
For Models 364 4
For Models 365 6

(4) ¾” White Plastic End Cap
For Models 363 6
For Models 364 8
For Models 365 10

(5) Vinyl Panel 1
(6) Rod and Rod Spring Retainer Set

For Model 363 6
For Model 364 8
For Model 365 10

Visit our website www.wincomfg.com/product-documents/parts-lists for a complete part s list catalog of your chair or

call Customer Service @ 1-800-237-3377 to request it by mail.

006290 Rev G Date 07-23-12 JWC