Winco 3170 User Manual
CUSTOMER INSTRUCTIONS
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
e-mail: customerservice@wincomfg.com before attempting to use this product; otherwise injury may occur.
Winco assumes no responsibility for damage or injury caused by the
3170 Designer Three Panel Screen
If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-3377,
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER place screen on a cart, table, stand or other objects; Screen could fall and INJURY MAY OCCUR.
3. NEVER place screen near open flame or over a radiator or heat register.
4. NEVER place screen in front of a door or exit sign; or during emergency screen could hinder evacuation.
5. SUFFOCATION DANGER to children if vinyl is not attached to screen; Screen could block nose and mouth
and prevent breathing. VINYL SCREEN IS NOT A TOY.
6. DO NOT allow children to play with screen; Screen could fall and INJURY MAY OCCUR.
7. Screen should ALWAYS be positioned on level surface.
8. NEVER stand or ride on screen legs; INJURY MAY OCCUR.
9. DO NOT use screen in or with ANY type of vehicle or trailer.
10. DO NOT attach objects to screen frame; Screen can tip over and INJURY MAY OCCUR.
11. Remove from service; Any screen with broken or missing parts, torn vinyl, or other visible damage.
12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
13. SAVE THESE INSTRUCTIONS for future reference and training.
improper assembly, installation or use of these products.
Tools needed:
• Scissors or box cutter
• 5/32 Allen Wrench (provided)
1. After checking your product for any shipping damage, remove all packing material and hardware that was secured for
shipping. Cut tape and/or plastic with scissors, being careful not to damage screen.
LEG INSTALLATION SEE PHOTOS, NEXT PAGE
2. Insert both Leg Frame Assemblies (#3) into the bottom of the Wing/Mid Frame Assembly (#1A).
Line up the holes in (#3) w/ the holes in (#1A).
3. Using the Allen Wrench provided screw in 1-Button Socket Screw (3D), per leg, through (#1A) and into (#3)
PANEL REPLACEMENT SEE PHOTOS, NEXT PAGE
4. To replace Vinyl Panels (#4), hold the screen by the top Screen Rod (#2A).
5. Next, using the Allen Wrench provided, push in on the small hole just below the Snap Button (#2B).
Re-install (#2A) by repeating the above procedure, then release (#2B) when (#2A) is in place
CARE & MAINTENANCE OF YOUR SCREEN
6. Periodically check all fasteners for tightness.
7. To clean Vinyl Panels use only mild liquid soap and water.
Wrinkles in Vinyl – Storage and/or shipping causes wrinkles in the vinyl of your Winco Screen; This is normal. Please allow
1-2 weeks at room temperature (approx. 70+ degrees) to allow for vinyl to return to original appearance.
006250 Rev N Date 06-26-13 JWC
Page 1 of 4
Page 2 of 4
Items Included with Screen: Qty.
(1A) Wing/Mid Frame Assembly Kit 1
(1B) Domed Plastic Insert 10
(2B) Snap Buttons 4
(3D) ¾” Button Socket Screw 2
(2A) Screen Rod 6
(2B) Snap Buttons 12
(3) Leg Frame Assembly 2
(3B) 2” Caster 4
(3C) Caster Insert 4
¾” Button Socket Screw 2
(3D)
(4) 3170 Vinyl Panel 3
Visit our website www.wincomfg.com/product-documents/parts-lists for a complete parts list catalog of your chair or
call Customer Service @ 1-800-237-3377 to request it by mail.
006250 Rev N Date 06-26-13 JWC
Loading...