2
INSTALLATION INSTRUCTIONS
4 WHEEL DOLLY KIT
3
6
4
7
1
5
8
COMPONENT LIST
REF. # PART # DESCRIPTION QTY.
1 300066-4 Left Handle Support 1
2 300066-3 Right Handle Support 1
3 15775-007 Front (Engine) Axle Bracket 1
4 15775-006 Rear (Gen-end) Axle Bracket 1
5 64326-020 Axle 2
6 SEE NOTE BELOW 43657-003 Pneumatic Wheel & Tire 4
7 61857-004 Handle 1
8 16343-000 Axle Protector 4
16199-107 Parts Bag 1
NOTE: Foam Filled Wheel & Tire is part # 43657-004
Hard Rubber Wheel & Tire is part # 43657-005
112048-00 16199-011I
STEP 1
Open hardware bag and separate components.
•
FASTENERS & MISC. COMPONENTS
(not shown in actual size)
13
9
10
11
12
22
HARDWARE & FASTENER LIST
14
21
15
18
16
17
19
20
REF # PART # DESCRIPTION QTY
9 56842-005 1/4” X 2“ Carriage Bolt 2
10 56842-004 1/4” X 1 3/4 “ Carriage Bolt 4
11 479-000 1/4“ Split Lock Washer 6
12 47517-000 1/4” Nylock Nut 6
13 1178-000 Flat Washer 8
14 64327-000 Hub Cap 4
15 96286-006 Nylon Flat Washer 2
16 64688-007 Spacer 4
17 93402-002 Hole Plug 2
18 465-000 5/16” X 7/8” Bolt 8
19 458-000 5/16” Nylock Nut 8
20 480-000 5/16” Split Lock Washer 8
21 62912-000 Foam Strip 1
22 526-000 Flat Washer 8
212048-00 16199-011I
STEP 2
Cut the foam strip (ref. 21) in half using a scissors. Apply to the underside of the
•
handle supports (ref. 1 & 2). Insert hole plugs (ref. 17) into the ends of the handle.
•
Bolt left and right handle supports (ref. 1 & 2) to the cradle using hardware (ref.
10, 11, 12). Place the nylon fl at washer (ref. 15) between the handle supports
and handle then attach handle (ref. 7) using hardware (ref. 9, 11, 12). Tighten the
nylock hex nuts (ref. 12). Do not over-tighten so that the handle will move freely.
HPS12000HE
CRADLE SHOWN
HERE
STEP 3
•
Remove the generator from the pallet and block generator up 8 to 10 inches to
gain access to the bottom of the cradle assembly. A lifting jack or hoist may also
be used if available.
WL12000HE
SHOWN HERE
312048-00 16199-011I
STEP 4
Bolt Front Axle Bracket (ref.3) on the engine end of the cradle and Rear Axle
•
Bracket (ref.4) to the generator end of the cradle using hardware (ref. 18, 22, 19,
20). Make sure the axle brackets are on the inside of the cradle cross-members.
The fl at washers (ref. 22) go onto the bolts (ref. 18) fi rst.
STEP 5
•
Remove and discard axle protectors (ref. 8). Tap one hubcap (ref.14) onto axle
(ref. 5) using a rubber mallet. Slide washer (ref. 13), wheel (ref. 6), washer (ref.
13) and spacer (ref. 16) onto axle (ref. 5). Then slide assembly through rear axle
bracket. (ref. 4) Place other spacer, washer, wheel, washer and hubcap on axle.
•
Slide washer (ref. 13), wheel (ref. 6), washer (ref. 13) and spacer (ref. 16) onto
axle (ref. 5). Slide the assembly through the front axle bracket (ref. 3) and lower
the unit to the ground. Place other spacer, washer, wheel and washer on axle.
Tap the last hubcap on the axle. NOTE: Do not tap too hard as you may dent the
hubcaps.
Winco Inc.
Service Dept.
507-357-6831
WL12000HE
CRADLE SHOWN
HERE
412048-00 16199-011I
Loading...