Licensee
Winchester Super X2 Semi-automatic Shotgun Owner’s Manual
2
Important instructions for
Winchester Super X2
Semi-automatic Shotgun
U.S. Repeating Arms Company, Inc.
344 Winchester Ave.
New Haven, CT, U. S. A. 06511-1970
Winchester trademarks licensed from Olin Corporation.
Use the space below to record information about your
new Super X2 shotgun.
Model _________________________________________
Serial Number __________________________________
Purchased From _________________________________
Date of Purchase ________________________________
We sincerely hope that you are pleased with your new
Winchester Super X2 shotgun. We at U.S. Repeating
Arms Company thank you for the privilege of providing this
shotgun to you. We are especially proud of the many years
of enjoyment it is certain to provide for you and your
family. The Super X2 is another shotgun in an over 130
year-old tradition of producing quality firearms for the
World’s sportsmen. Quality of manufacture, design,
craftsmanship and function are of utmost concern to us.
We believe you’ll find that your new Super X2 meets the
Winchester tradition of quality in every way. If you have
any questions or comments regarding your new firearm,
please feel free write to us at our administrative offices:
Customer Service Department
U. S. Repeating Arms Company, Inc.
275 Winchester Avenue
Morgan, Utah 84050-9333
Phone: 1-800-945-5237
PRINTED IN U.S.A. MF9811/98062
3
Contents Page
Gun safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
General description/operation . . . . . . . . . . . . . . . . . . . . .5
Terminology and descriptions . . . . . . . . . . . . . . . . . . . . . .7
Serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Magazine capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Initial cleaning/oiling . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Operation of the safety . . . . . . . . . . . . . . . . . . . . . . . . . .11
Initial assembly/take down . . . . . . . . . . . . . . . . . . . . . . .13
Loading procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Unloading procedures . . . . . . . . . . . . . . . . . . . . . . . . . .17
Firing procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
In the case of a misfire . . . . . . . . . . . . . . . . . . . . . . . . . .20
Magazine plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Trigger group disassembly/reassembly . . . . . . . . . . . . . . .22
Bolt disassembly/reassembly . . . . . . . . . . . . . . . . . . . . . .26
Invector®Plus threaded choke system . . . . . . . . . . . . . .30
Use of extra barrels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Cleaning and maintenance suggestions . . . . . . . . . . . . .33
Ordering parts / Service or repair . . . . . . . . . . . . . . . . . .37
Questions / Winchester-guns.com . . . . . . . . . . . . . . . . .38
The Super X2 is truly a remarkable new shotgun — a world class
shotgun with world class origins. Its manufacture represents an
unprecedented collaborative effort between the traditional
Winchester firearms manufacturing plant in New Haven,
Connecticut and our associated plants in various European
locations. Thus the distinctive barrel marking. In addition,
Super X2 testing and research and development spans the globe
from our Utah facility to Connecticut to Belgium. It is a new
breed of Winchester from a new “global” Winchester brand.
Every aspect of its design points toward two primary objectives:
(1) unmatched reliability, and (2) superb handling. While it is
true that the overall design draws on nearly a century of
Winchester firearms shotgun experience, it is clear that this in
an all new Winchester with performance features the most
demanding hunters and shooters want.
A few things to take notice of are:
• The remarkably simple , self-adjusting, self-cleaning gas piston
system.
• The alloy receiver that balances weight between the hands with
just enough barrel weight for smoothness.
• The acclaimed Invector
®
Plus choke system that incorporates
long choke tapers and a back-bored barrel for better patterns.
• The large, exceptionally functional safety button.
As you learn about your new Super X2 and begin shooting it,
we’re sure you’ll agree its design sets new standards for reliability
and handling performance.
4
GUN SAFETY WARNINGS
IT IS ESSENTIAL THAT THESE OPERATING
INSTRUCTIONS BE THOROUGHLY STUDIED
BEFORE USING THIS FIREARM TO ASSURE
PROPER AND SAFE GUN HANDLING. FAILURE
TO FOLLOW THESE INSTRUCTIONS OR
FAILURE TO OBEY ANY SAFETY WARNING
MAY RESULT IN INJURY TO YOURSELF OR
OTHERS, OR CAUSE DAMAGE TO YOUR GUN.
As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can
be the difference between life and death. There is no
excuse for careless or abusive handling of any firearm.
At all times handle your Super X2 and any other firearm
with intense respect for its power and potential danger.
PLEASE READ AND UNDERSTAND ALL OF THE
CAUTIONS, PROPER HANDLING PROCEDURES
AND INSTRUCTIONS OUTLINED IN THIS
BOOKLET BEFORE USING YOUR NEW
FIREARM.
1. Do not carry a loaded gun with a live round in the
chamber while walking, running, climbing a tree, crossing
a fence or anywhere you might slip or fall, drop the gun
or otherwise bump or jar the gun. A gun that is dropped,
bumped, or jarred with a chambered round might acciden-
tally discharge even with the safety on, causing serious
injury to you or someone else. When a round is chambered
keep the safety on until you are ready to shoot.
2. Do not rely on the safety to prevent accidental
discharge. Many safeties merely block the trigger and
prevent firing by pulling the trigger. The safety may not
prevent an accidental discharge due to dropping, jarring,
or bumping a gun.
3. Use only ammunition for which the gun is chambered
as indicated on the barrel, to prevent excessive pressure
and possible serious personal injury.
4. Incorrectly reloaded ammunition can cause serious
personal injury and damage to the firearm due to excessive
pressure. Reload only after proper instruction and in strict
compliance with instruction and data contained in current
reloading manuals.
5. Never point a gun at anything you do not intend to
shoot. Always keep it pointed in a safe direction in case
of accidental discharge.
6. Always check to ensure that the barrel is free of
obstructions before loading and using the gun. If you
experience light recoil or off sound, check the barrel for
an obstruction.
7. Before firing, clean any grease or oil out of barrel with
cleaning rod and patch. Grease or heavy accumulation of
5
oil can cause excessive pressure and result in serious
personal injury.
8. Keep barrel, chamber and action free of rust. Rust in
the barrel and chamber can cause excessive pressures
resulting in serious injury. A rusted, pitted or eroded
barrel should be replaced.
9. Use hearing protection to prevent ear damage from
repeated exposure to gunfire.
10. Always use proper shooting glasses to prevent eye
injury from flying particles.
11. Never carry a loaded gun in a motor vehicle or carry
one into a dwelling. Always carefully unload the gun
before entering a motor vehicle, a dwelling or an area
such as a camp. Always point a gun in a safe direction
while loading or unloading to prevent serious injury in
case of an accidental discharge. Never load in the house
or in your vehicle.
12. Never shoot at a hard, flat surface or at the surface
of water to avoid a ricochet and possible serious personal
injury to yourself or a bystander.
13. Store gun in a clean dry place out of reach of children
and separated from stored ammunition.
14. Never alter any parts of your gun. Any alterations or
adjustments that may become necessary to the operating
mechanism should be performed by a qualified gunsmith.
15. Hunting from elevated surfaces such as tree stands is
dangerous. Doing so may increase the risk of handling any
firearm. Always make certain that the stand being used is
safe, sturdy and stable. Always make certain your firearm
is unloaded when it is being taken up and down from the
stand. Always make certain that your firearm is not
dropped from the stand or dropped while it is being taken
up or down from the stand.
16. Discharging firearms in poorly ventilated areas, cleaning
firearms, or handling ammunition may result in exposure
to lead and other substances known to cause birth defects,
reproductive harm and other serious physical injury. Have
adequate ventilation at all times. Wash hands thoroughly
after exposure.
GENERAL DESCRIPTION/OPERATION
Your new Super X2 is one of several different versions and
configurations offered. The basic operating procedures are
the same for all of them. Where there are differences they
are pointed out in this manual for your convenience.
The Super X2 is a semiautomatic design that allows the
shooter to shoot followup shots by merely pulling the trigger,
firing the first shot, and then letting the gas piston system
automatically move a shell from the magazine to the
chamber where it is fired with a pull of the trigger.
6
This can be repeated until the magazine is empty. A single
round can also be inserted into the chamber manually or
moved from a loaded magazine by cycling the action with
the bolt handle.
It is capable of shooing five shots (with the magazine plug
removed, using 2 3/4” loads) in rapid succession with each
pull of the trigger.
The short stroke of the gas piston along with the snug, gas
sealing fit of the piston rings and tight fit of the piston
rod, limits the amount of combustion gases blown past the
gas cylinder and into the receiver, keeping the inside of
the receiver clean.
This is an exceptionally advanced design that offers reliable
function of the gas system and easy disassembly for maintenance and cleaning. However, in order to keep your
new shotgun in top condition and operating at its peak
performance you must read, understand and follow all of
the instructions in this manual.
Prior to using live ammunition, familiarize yourself
thoroughly with these operating instructions. Get
accustomed to the feel of your new gun. Know the forces
required to operate the action. Learn how to pull the
trigger, and above all, know the location and operation of
the safety. Procedures for disassembly and operation of
various components are outlined in the sections below.
Please read and study them thoroughly. In addition,
always remember:
FIGURE 1
Invector Plus
Choke System
®
Magazine Cap
Forearm
Magazine Tube
(inside forearm)
Carrier Release Button
Trigger
Guard
Recoil Pad
Ejection Port
Vent Rib
Safety
Trigger
Buttstock
Receiver
7
USE THE CORRECT AMMUNITION AS REFERENCED BY THE INSCRIPTION ON THE BARREL.
BEFORE LOADING YOUR GUN BE SURE ALL
GREASE AND OIL HAVE BEEN REMOVED
FROM THE BARREL AND CHAMBER, AND
THERE ARE NO OBSTRUCTIONS.
IMPORTANT: ALWAYS KEEP THE MUZZLE
POINTED IN A SAFE DIRECTION.
TERMINOLOGY AND DESCRIPTIONS
Descriptions in this manual generally refer to the gun in
the horizontal position. That is, in the normal firing
position. For example, the muzzle is forward or front; the
butt stock is rearward or rear; the trigger is downward or
underneath; the sight is upward or on top. For general
parts terminology, refer to Figure 1.
The Winchester Super X2 is also shown disassembled to
the extent necessary in order to follow instructions
contained in this book (refer to Figure 14 later in this
manual). Figure 2 covers the general features and benefits
of the Super X2 design.
Throughout this manual the “action” refers to the mecha-
nism of this shotgun which loads and secures the shell in
the chamber.
SERIAL NUMBER
The serial number is located on the left side of the
receiver, just above the trigger guard. Record the serial
number at the front of this manual for future reference.
AMMUNITION
There are several different versions of the Super X2.
They are inscribed as follows on the receiver:
•Magnum 3 1/2”. This model is designed to shoot all
factory field loads including 2 3/4” length field loads,
3” Magnum loads and 3 1/2” Magnum loads. It has a
3 1/2” chamber. (It is not designed to shoot the lightest
factory target 7/8 oz. and 1 oz. loads.)
• Magnum 3”. This model is designed to shoot all factory
loads from 2 3/4” target loads to 3” Magnums. This model
has a 3” chamber. It is specifically configured to be able
to handle down to 7/8 oz. factory ultra-light target loads.
(It is NOT designed to shoot 3 1/2” shells.)
Winchester ammunition is always an excellent choice for
your new Winchester firearm, delivering the unmatched
performance and dependability you want.
(Continued on page 10)
8
Not only does the advanced alloy receiver offer the
strength of steel, it also affords the Super X2 exceptional
between-the-hands balance, with just the ideal barrel
weighting for a smooth swing.
The entire bolt assembly removes easily for
a thorough cleaning. This is a gun designed
for hard work under real hunting conditions.
You get a complete selection of functional stock
materials to choose from: composite black,
dipped camouflage composite and walnut models.
Deluxe recoil pad for
maximum comfort.
SUPER X2 FEATURES
The trigger assembly easily
removes with a durable two-pin
system. No tools are necessary
and it takes just seconds to do
maintenance and cleaning.
The large safety button offers excellent
convenience with both gloved and
ungloved fingers. Plus, it is reversible
for left-handed shooters.
9
FIGURE 2
The barrel is back-bored for
improved pattern performance.
Current Super X2 hunting models are fitted with the proven Invector
Plus choke system. These longer tubes have special tapers for
optimum patterning — plus they are specially designed for back-bored
barrels. It allows you to change choke constrictions to meet the
demands of the game being hunted or target shot. Extra-full choke
tubes are available for hunting turkey or other game requiring
extremely tight patterns with lead shot loads.
Super X2 field guns feature our
fully floating ventilated rib.
Invector®Plus
threaded choke
system.
The advanced, self-cleaning gas system uses just the
amount of gas needed to cycle the action. Even the 3 1/2”
Magnum model can function reliably down to 2 3/4” field
loads. The 3” Magnum version handles all loads from
3” Magnum down to the lightest 7/8 oz. target loads.
10
MAKE SURE YOU USE ONLY THE EXACT
AMMUNITION/CALIBER AS LISTED ON THE
LEFT SIDE OF THE BARREL.
U.S. REPEATING ARMS COMPANY, INC., CAN
ASSUME NO RESPONSIBILITY FOR INCIDENTS
WHICH OCCUR THROUGH THE USE OF
CARTRIDGES OF NONSTANDARD DIMENSION
OR THOSE THAT WHEN SHOT, DEVELOP
PRESSURES IN EXCESS OF INDUSTRY
STANDARDS ESTABLISHED BY THE
SPORTING ARMS AND AMMUNITION
MANUFACTURERS’ INSTITUTE (SAAMI).
DISCHARGING FIREARMS IN POORLY
VENTILATED AREAS, CLEANING FIREARMS,
OR HANDLING AMMUNITION MAY RESULT IN
EXPOSURE TO LEAD AND OTHER SUBSTANCES
KNOWN TO CAUSE BIRTH DEFECTS,
REPRODUCTIVE HARM AND OTHER SERIOUS
PHYSICAL INJURY. HAVE ADEQUATE
VENTILATION AT ALL TIMES. WASH HANDS
THOROUGHLY AFTER EXPOSURE.
Incorrectly reloaded ammunition can cause serious
personal injury and damage to the firearm due to excessive
pressure. Reload only after proper instruction and in strict
compliance with instructions and data contained in
current reloading manuals.
MAGAZINE CAPACITY
It is extremely important that you know the magazine
capacity of your Super X2. It is listed on the hang tag
supplied with your Super X2. Under appropriate circumstances — at a range or other suitable shooting location
— load your magazine to full capacity and make note of
the number of shells. Remember, “total capacity” includes
an additional round which can be loaded manually in the
chamber in addition to a full magazine. Total capacity is
generally (magazine, plus chamber) as follows:
3 1/2” Magnum Versions
3” and 3 1/2” Magnum loads: Three in magazine, one
in chamber.
2 3/4” loads: Four in magazine, one in chamber.
3” Magnum Versions
3” Magnum Loads: Three in magazine, one in chamber.
2 3/4” loads: Four in magazine, one in chamber.
With magazine adapter (plug) installed
Two shells in the magazine, one in chamber.
IMPORTANT: The Super X2 will handle mixed loads of
different shell lengths, which will affect total capacity.
11
INITIAL CLEANING / OILING
Some metal parts of your new Super X2 have been coated
at the factory with a rust preventative compound. Before
using your Super X2, clean the anti-rust compound from
the inside of the barrel, receiver, breech bolt mechanism
and the action/chamber areas. A high quality, lightweight
gun oil should be used to remove this compound and to
give your new gun its first lubrication. Clean the barrel
using a cleaning rod and patch as explained under
“Cleaning and Maintenance Suggestions” found later in
this manual.
If your new Super X2 is to be stored for an extended period of time, it is permissible to leave the rust preventative
compound in place and keep your Super X2 in its box for
maximum protection during long-term storage.
Before beginning assembly of your Super X2 you should
first wipe the mechanism clean and apply a few drops of
quality oil on the surfaces shown (see Figure 3).
Avoid applying too much oil. Only a light film is
necessary. Excessive oil should be wiped off, especially in
cold weather.
OPERATION OF THE SAFETY
Your new Super X2 shotgun is designed with a cross bolt
type safety. It is located just rearward of the trigger on the
trigger guard: convenient for gloved or ungloved fingers.
It is essential that you become very familiar with the feel,
look and operation of the safety on this shotgun before
attempting to load and shoot.
With the safety in the “on safe” position the trigger and
hammer are blocked and the shotgun cannot be fired.
In the “off safe” position — if your gun is loaded with a
round in the chamber — the chambered round can be
fired by simply pulling the trigger.
The safety on the Super X2 is reversible for right or lefthanded operation. It comes from the factory in the right
hand position. Verify the installation of your guns’ safety.
Instructions in this manual are for the safety installed in
the right-handed position.
• “ON SAFE”. The safety button is pushed fully to the
right. The red band on the left side is not showing (see
Figure 4A).
Be sure you lightly oil your
Super X2 at these points.
FIGURE 3
12
• “OFF SAFE”. The safety button is pushed fully to
the left. A large red band is exposed on the button as it
protrudes on the left side. The red band is an added aid to
safe gun handling. However, with time and exposure to
the elements it can wear off.
Never rely totally on your gun’s safety button. It is merely
an aid to safe gun handling. Like any mechanical device
the safety can possibly fail: it can be jarred or inadvertently
manipulated into an unsafe condition. Always keep your
shotgun pointed in a safe direction.
At all times in the field keep the safety in the “ON SAFE”
position and the barrel pointed in a safe direction. It is a
good idea never to load your shotgun until you are in the
field and shooting is imminent or until you are at your
station and it is your turn to shoot when you are shooting
at a range. For extra safety, and as a courtesy to others,
fully unload and place the action in the open position
at all times other than when shooting is immediately
imminent.
THE SAFETY IS REVERSIBLE AND CAN BE
REVERSED FROM RIGHT-TO LEFT-HANDED
BY A COMPETENT GUNSMITH. WHEN
INSTALLED, THE LEFT-HANDED SAFETY WILL
HAVE THE SAFETY BUTTON’S RED WARNING
BAND ON THE RIGHT SIDE OF THE TRIGGER
GUARD.
Note: Do no depend on the red color alone to indicate
your gun’s safety status, as time, exposure to the elements,
and the abrasive action of cleaning agents can erase it.
FIGURE 4A
“On Safe” position
FIGURE 4B
“Off Safe” position.
Red band showing.
13
INITIAL ASSEMBLY / TAKE DOWN
Remove the barrel assembly and receiver/stock section
from the carton. Wipe them clean and lightly oil component parts as explained under “Initial Cleaning/Oiling.”
The Super X2 shotgun usually comes (from the factory)
with the barrel removed and the forearm still attached to
the magazine tube.
It is important to carefully follow the assembly instructions below — especially steps 1, 2 and 3 — to assure the
proper assembly of your shotgun.
ALWAYS PLACE THE SAFETY IN THE “ON
SAFE” POSITION BEFORE BEGINNING
ASSEMBLY PROCEDURES AND CHECK YOUR
GUN CAREFULLY TO BE CERTAIN THAT
THE CHAMBER, FEED MECHANISM AND
MAGAZINE CONTAIN NO SHELLS.
1. Lock the bolt rearward by pulling the operating handle
fully to the rear. If it will not pull rearward it usually indicates that the bolt slide link has fallen out of the end of
the socket on the return spring plunger while your gun
was being shipped. This is not a problem. You will simply
need to refer to the section titled “Bolt Disassembly/
Reassembly” later in this manual for special instructions
on how to perform this very easy alignment procedure.
2. Carefully remove the forearm from the magazine tube
by unscrewing the magazine cap and sliding the forearm
forward of the magazine tube.
DO NOT SQUEEZE HARD ON THE OPEN REAR
END OF THE FOREARM. TOO MUCH PRESSURE COULD CAUSE THE WOOD TO SPIT.
3. Leave the components of the gas system (the sleeve,
sleeve spring and gas piston) in place on the magazine
tube. They do not need to be removed, except for cleaning. In the event that components of the gas system have
been removed, it is easy to reinstall them as explained
below.
FIGURE 5
Align the piston rod with
the slot on the left side
14
4. If the gas piston and sleeve have been removed, first
slide the sleeve spring over the magazine tube. Then slide
the sleeve onto the magazine tube, piston rod end first.
Check the piston rod to make sure it is aligned with the
slot on the left side of the receiver (see Figure 5), as
viewed from normal shooting position.
5. Take the gas piston in hand and slide it into the rear of
the gas bracket on the barrel, smaller end first
(see Figure 6).
6. Hold the gun in the vertical position. Slide the gas
bracket and gas piston over the magazine tube
(see Figure 7). the barrel extension should slip solidly
down into the receiver. Make sure the piston rod on the
gas sleeve moves freely in its slot in the left side of the
receiver. On a new gun, with very tight tolerance, it may
be necessary to lift up slightly on the gas sleeve to allow
the barrel extension the room to drop into the receiver.
After you do this always check piston rod alignment as
explained previously.
7. Replace the forearm by sliding it onto the magazine
tube and over the gas bracket so it seats securely. Install
FIGURE 6 FIGURE 7
Position the piston in the gas bracket
on the bottom of the barrel.
Insert the gas piston and
gas bracket over the maga-
zine tube. Start the barrel
extension into the receiver
You may have to
lift up slightly on
the gas sleeve.
15
the magazine cap. Make sure the magazine cap is fully
tightened down. Open and close the action several times
and retighten the magazine cap. This will ensure a
proper seal.
TAKING DOWN THE BARREL —
BEFORE STARTING DISASSEMBLY
PROCEDURES, VISUALLY INSPECT THE
CHAMBER, FEED MECHANISM AND MAGAZINE
TO BE ABSOLUTELY CERTAIN THE SHOTGUN
IS COMPLETELY UNLOADED. POINT THE
BARREL IN A SAFE DIRECTION. PLACE THE
SAFETY IN THE “ON SAFE” POSITION’
The red warning band on the safety must not be visible.
Take-down for storage is essentially the reverse of assembly
procedures. The action should be left open if disassembly
of the rest of the gun will not be performed. If you intend
to fully disassemble your gun, you may start with the
action closed.
1. Unscrew the magazine cap and remove it.
2. Remove the forearm by sliding it forward off the
magazine tube.
3. If you are disassembling for cleaning remove the barrel,
piston, piston sleeve and sleeve spring by sliding them
forward off the magazine tube. See “Cleaning and
Maintenance Suggestions” later in this manual for cleaning
procedures.
NOTE: If you are disassembling for storage, lock the
action rearward. Leave the piston, piston sleeve and
spring on the magazine tube as explained previously.
Reinstall if they were removed. Install the forearm over
the magazine tube and screw on the magazine cap. You
will then have two compact units: (1) the barrel, and
(2) the action with forearm and stock.
CAUTION: AFTER THE BARREL HAS BEEN
REMOVED FROM YOUR GUN, AND YOU
INTEND TO STORE YOUR GUN, LEAVE THE
BOLT IN THE OPEN POSITION. DO NOT
PRESS THE CARRIER RELEASE BUTTON.
If the bolt is release forward with the barrel removed, the
bolt handle will hit the front of the ejection port and
cause damage to both the receiver and the bolt handle.
LOADING PROCEDURES
Before loading your gun, be sure all grease and oil has
been removed from the barrel and chamber and there are
no obstructions. Use the correct ammunition referenced
by the inscription on the barrel. There are two ways to
load the chamber of your Super X2.
16
Before loading the magazine make sure of the following:
1) Your shotgun is pointed in a safe direction.
2) The safety is in the “on safe” position.
3) You are in an appropriate location for shooting.
4) Shooting will be imminent.
DIRECTLY TO THE CHAMBER, SINGLE SHOT MODE —
1. Place the safety in the “ON SAFE” position.
2. Open the action by pulling back fully on the bolt handle. The bolt will lock in the rearward position. As a matter of practice, always verify that the magazine and chamber contain no shells when the action is opened.
3. A shell can now be placed directly into the ejection
port (brass of shell to the rear and crimp to the front). It
is fine to push the shell forward into the chamber, or just
leave it loose in the port (see Figure 8).
4. Press the carrier release button. This will automatically
move a loose round placed in the ejection port, directly
into the chamber. Keep your fingers clear of the ejection
port whenever closing the action with the carrier release
button.
IMPORTANT: The gun is now ready to fire by moving
the safety to the “off safe” position and pulling the trigger.
After firing with an empty magazine, the bolt will lock
rearward, ready for inserting the next shell in the open
ejection port.
LOADING THE MAGAZINE —
1. Place the safety in the “ON SAFE” position and close
the action by pressing the carrier release button.
2. Depress the carrier with the forward end of the nose of
the shell.
3. With your thumb on the base of the brass push the
shell into the magazine until the shell is held in the magazine by the cartridge stop (see Figure 9). Remove your
thumb and allow the carrier to return downward to its
original position.
4. Repeat the procedure until the magazine is fully loaded.
5. If firing is imminent, a shell can now be moved from
the magazine to the chamber by pulling back fully on the
FIGURE 8
When loading the chamber
directly, drop a loaded round
in the open ejection port.
17
bolt handle and releasing it forward. A round will be fed
automatically from the magazine to the chamber as the
bolt closes. Another round can then be inserted into the
magazine to load to full capacity.
IMPORTANT: THE GUN IS NOW READY TO
FIRE BY MOVING THE SAFETY TO THE “OFF
SAFE” POSITION.
DO NOT CARRY A GUN WITH A SHELL IN
THE CHAMBER TO AVOID ACCIDENTAL
DISCHARGE. IN ALL CASES, WHEN LOADING
AND WHEN FIRING IS NO LONGER IMMINENT,
MAKE SURE THE SAFETY IS IN THE “ON
SAFE” POSITION.
UNLOADING PROCEDURES
CAUTION: WHENEVER UNLOADING, ALWAYS
BE CERTAIN THAT THE MUZZLE IS POINTED
IN A SAFE DIRECTION AND THAT THE SAFETY
IS IN THE “ON SAFE” POSITION.
ALWAYS INSPECT THE CHAMBER, ACTION,
CARRIER AND MAGAZINE VERY CAREFULLY
AFTER UNLOADING TO BE SURE ALL LIVE
ROUNDS ARE CLEARED FROM THE GUN.
There are two ways to unload your Super X2.
CYCLING THE ACTION —
POINT THE MUZZLE IN A SAFE DIRECTION.
PLACE THE SAFETY THE “ON SAFE” POSITION.
MAKE SURE THE ACTION IS CLOSED AND
KEEP THE MUZZLE POINTING IN A SAFE
DIRECTION.
(The red warning band on the safety will
not be visible).
1. Grasp the bolt handle and cycle the action until all
rounds are transferred from the magazine to the chamber
and then ejected. It is possible, with practice, to catch
each shell with your free hand as it is ejected. You should
always take care to avoid damaging shells. Do not let
them fall on hard ground.
FIGURE 9
Push the shell all the way into the
magazine. Make sure you push the
rim past the cartridge stop.
18
2. When the last shell in the magazine has been cycled
through the chamber and out the ejection port, the
action will lock rearward. The action should lock rearward when the acton is cycled with an empty magazine.
3. Using your index finger, feel the entry of the magazine
to make sure there are no longer any shells that have not
been fed from the magazine and ejected. Visually inspect
the chamber, feed mechanism and magazine to assure
there are no shells remaining.
UNLOADING DIRECTLY FROM THE MAGAZINE —
POINT THE MUZZLE IN A SAFE DIRECTION.
PLACE THE SAFETY IN THE “ON SAFE”
POSITION, MAKE SURE THE ACTION IS
CLOSED AND KEEP THE MUZZLE POINTING
IN A SAFE DIRECTION.
1. Turn the gun over so the trigger guard is facing up, then
push the carrier down with our finger as far as it will go.
2. Push inward on the right side of the cartridge stop,
releasing the shell from the magazine. Be careful not to
pinch your finger. The cartridge stop is located on the
inside right side of the loading port (visually to your left
side when looking down into the loading port). When a
shell is in the magazine, the stop catches on the brass of
the shell. As the cartridge stop is pressed in, the shell will
be forced out of the magazine under spring pressure (see
Figure 10). Capture it as it comes out. Press the stop again
to release the next shell. Do this until the magazine is
empty.
3. With the safety still in the “on safe” position, pull rearward on the bolt handle to eject the cartridge from the
chamber. The bolt will lock rearward when the action is
cycled with an empty magazine.
4. Using your index finger, feel the entry of the magazine
to make sure there are no longer any shells that have not
been feed from the magazine and ejected. Visually inspect
the chamber, feed mechanism and magazine to assure
there are no shells remaining.
IMPORTANT — AFTER UNLOADING ALWAYS
VISUALLY CHECK AND KNOW FOR SURE
THAT YOUR SHOTGUN IS NOT LOADED.
FIGURE 10
Remove shells from the magazine
by pressing in on the cartridge stop
with your finger.
19
FIRING PROCEDURES
The semiautomatic or self-loading characteristic of the
Super X2 is the obvious primary benefit to the shooter.
For training or target situations your gun can be shot
“single shot” by loading one shell at a time through the
open ejection port. More commonly you will take advantage of the semiautomatic feature by loading the entire
magazine first and then firing repeated shots, if necessary.
Both are described earlier under “Loading Procedures.”
1. When ready to shoot, and with a loaded shell in the
chamber, the safety “on safe”, and your finger off the trigger, push the safety to the “off safe” position (with the red
warning band fully visible). Your shotgun is now ready to
fire with a pull of the trigger
CAUTION: YOUR SHOTGUN IS NOW READY
TO FIRE. REMEMBER, THE RECOIL FROM A
SHOTGUN, ESPECIALLY MAGNUM LOADS,
WILL BE SOMEWHAT HEAVIER THAN MOST
OTHER GUNS, SO FIRMLY SHOULDER YOUR
SUPER X2, TAKE AIM, AND — WHEN ON
TARGET — SQUEEZE THE TRIGGER.
2. As the shell in the chamber is fired, gases from the firing shell are bled off from the barrel at the gas bracket.
This forces the gas piston rearward which moves the bolt
assembly rearward, ejecting the fired shell.
3. As the bolt returns forward under spring force a shell
from the magazine is automatically transferred from the
magazine to the chamber and the bolt locks forward.
Your gun will now fire again with the pull of the trigger.
Immediately put the safety in the “on safe” position (with
the red warning ring hidden) until you are ready to fire
again.
4. You may fire until the magazine is empty. The bolt will
lock rearward after the last shot has been feed from the
magazine, fired and ejected. When the bolt locks rearward
this usually indicates that both magazine and chamber are
empty, and that your shotgun magazine needs to be
reloaded. It is important to treat your gun as though it is
loaded, even if the action has locked rearward.
At this point either refill the magazine with loaded
cartridges (if shooting is going to continue) or fully
unload your shotgun (if shooting is completed). Either
way, place the safety in the “on safe” position.
WHEN FIRING IS COMPLETED OR WHEN
SHOOTING IS NO LONGER IMMINENT,
IMMEDIATELY RETURN THE SAFETY TO THE
“ON SAFE” POSITION.
IMPORTANT: UNDER NO CIRCUMSTANCES
SHOULD YOU MOVE ON OR CONTINUE TO
HUNT WITH YOUR SAFETY IN THE FIRE
POSITION.
20
IN THE CASE OF A MISFIRE
Only rarely will modern factory ammunition experience
a misfire. If this ever happens to you when shooting your
Super X2, please follow these instructions carefully.
CAUTION: IN CASE OF MISFIRE, KEEP THE
BARREL POINTED IN A SAFE DIRECTION,
CAREFULLY OPEN THE ACTION WHILE
AVOIDING DIRECT EXPOSURE TO THE
BREECH BY YOURSELF AND OTHERS.
REMOVE THE SHELL FROM THE CHAMBER.
FULLY UNLOAD YOUR SHOTGUN, REMOVING
ALL SHELLS FROM THE MAGAZINE.
Carefully inspect the ejected shell. If the primer is indented,
the shell should be disposed of in a manner that
would prevent accidental injury to you, others, or the
environment. If there is no indentation, your gun has
malfunctioned and should be serviced by a qualified
gunsmith, or by a U.S. Repeating Arms Co. Authorized
Repair Center (ARC).
MAGAZINE PLUG
The Super X2 is delivered with the magazine three shot
adapter (plug) installed in the magazine, limiting magazine
capacity to two shells in compliance with federal migratory
bird regulations. If you do not wish to be limited to three
shots — when it is not required by law — you can remove
the three shot adapter (plug).
WHEN REMOVING THE PLUG BE CERTAIN
THERE ARE NO SHELLS IN THE MAGAZINE
OR CHAMBER AND KEEP THE BARREL AND
MAGAZINE POINTED IN A SAFE DIRECTION
AT ALL TIMES.
Remember, the plug is under spring pressure so care must
be taken for safe removal. Always point the end of the
magazine away from your face and in a safe direction.
Never look directly down into the cap end of the open
magazine.
ALWAYS WEAR EYE PROTECTION WHEN
REMOVING AND REINSTALLING THE
MAGAZINE’S 3-SHOT PLUG.
IMPORTANT: Use only the three-shot adapter supplied
with your Super X2 or a replacement part made specifically for your Super X2 shotgun by U.S. Repeating Arms.
This is a special three-shot adapter design that maximizes
the performance of your gun with any load. The use of
any other adapter may affect performance of the magazine
system.
Removal and installation can be performed with the barrel
in place or with the barrel removed from the action.
21
REMOVAL —
1. First, make certain the gun is totally unloaded and the
safety is “on safe.”
CHECK THE MAGAZINE, FEED MECHANISM
AND CHAMBER TO BE SURE THEY DO NOT
CONTAIN ANY SHELLS.
2. Unscrew the magazine cap and remove it. Remember,
always point the end of the magazine away from your face
and in a safe direction.
3. Remove the forearm by sliding it forward, over the gas
bracket. It is also acceptable to remove the barrel as
explained previously under “Initial Assembly/Takedown.”
4. The magazine three-shot adapter lays underneath the
magazine spring retainer locked in the forward end of the
magazine tube. To remove the magazine spring retainer,
depress the magazine spring retainer tab, located in the
window on the magazine tube while keeping your hand
on the magazine spring retainer. (See Figure 11). Slowly
remove the magazine spring retainer as it is under pressure
of the magazine spring. (See Figure 12).
5. As the spring pushes the retainer out of the tube the 3shot adapter will come with it. Remove the retainer, the
magazine 3-shot adapter and the spring from the magazine
tube.
6. Remove the three-shot adapter from between the
retainer and the spring (See Figure 13).
FIGURE 11
Depress the
magazine spring
retainer tab.
Keep your free
hand over the
retainer.
FIGURE 12
Slowly remove the magazine spring
retainer. Keep it under control with your
hand, as it is under spring pressure.
22
REINSTALLATION —
1. Depress the magazine spring back into the magazine
tube and replace the magazine spring retainer over the top
of the spring.
2. Align the magazine retainer tab with the rectangular
slot in the magazine tube. Push the magazine spring
retainer down into the magazine. Make sure the magazine
spring retainer tab is locked in place in its retaining slot
in the magazine.
3. Reinstall the barrel (if it was removed), the forearm
and then the magazine cap as explained under “Initial
Assembly/Takedown.”
4. Note: In the future, should you wish to limit your gun
to three shots again, unscrew the magazine cap, remove
the forearm and remove the magazine spring retainer as
explained previously. Hold the spring down inside the
magazine tube. Then insert the tapered end of the adapter
inside the spring and lightly press the front end of threeshot adapter to force the magazine spring into the magazine until the base of the three-shot adapter is level with
the end of the magazine tube. Replace the magazine
spring retainer, forearm and magazine cap. Make sure the
magazine follower remains in place inside the rear of the
magazine tube.
TRIGGER GROUP DISASSEMBLY/REASSEMBLY
One of the advantages of a Super X2 is the ability to easily
disassemble the action for cleaning. Under very harsh
weather conditions and in dirty environments just knowing that parts are clean and lightly oiled can add an extra
measure of confidence to your hunt.
Make sure you have a clean place to work and a good
place to put the components as they are disassembled.
Wear eye protection at all time. Never disassemble
beyond what is explained and shown in this manual. Full
disassembly of all basic components is shown at right
(See Figure 14).
Disassembling the action can be done in the field, but
remember, there are small parts involved, some of which
FIGURE 13
Remove the 3-shot adapter from
the end of the magazine spring.
23
FIGURE 14
Barrel
Extension
Bolt
Bolt Slide
Bolt Slide Link
Gas Bracket
Three Shot Adapter
Magazine Tube
Gas Piston
Trigger Group
Trigger Group Pins
Forearm
Magazine Spring
Bolt Handle
Gas Sleeve
Sleeve Spring
Magazine Cap
Magazine
Spring
Retainer
Follower (inside)
24
are under spring tension.
BEFORE ANY ASSEMBLY OR DISASSEMBLY
PROCEDURES FIRST, MAKE CERTAIN THE
GUN IS TOTALLY UNLOADED AND THE
"SAFETY" IS THE "ON SAFE" POSITION. BE
CERTAIN THERE ARE NOT SHELLS IN THE
MAGAZINE, CHAMBER OR FEED MECHANISM.
PLACE THE SAFETY IN THE "ON SAFE"
POSITION.
ALWAYS WEAR EYE PROTECTION WHEN
PERFORMING ANY MAINTENANCE OR
DISASSEMBLY.
HOW TO REMOVE THE TRIGGER GROUP —
Removing the trigger guard group is another necessary
procedure in performing thorough maintenance of your
shotgun. It is easy to do, and removing it allows you to
perform cleaning and maintenance whenever and wherever required. With both the trigger guard group and bolt
assembly removed, it is easy to wipe out any debris or
moisture that sometimes accumulates in the receiver.
1. Make sure the gun is unloaded. Place the safety in the
“ON SAFE” position and leave it there during disassembly
and cleaning. This assures that the hammer does not
inadvertently fall forward during cleaning. Full disassembly
involves removal of the bolt assembly and the trigger group.
Any disassembly beyond this should only be performed by
a competent gunsmith.
2. Under most circumstances, first remove the barrel and
gas system components as explained under “Initial
Assembly/Takedown.” It is acceptable for the trigger
group to be removed without removing the barrel —
although it makes sense to remove the barrel if you are
cleaning your gun.
3. After removing the barrel and forearm, it is good practice to immediately screw the magazine cap back onto the
magazine.
4. VERY IMPORTANT: The bolt must be slowly moved
from the open to the forward, closed position. You must
FIGURE 15
Carefully lower the bolt forward to
the closed position. You can damage
the receiver by slamming the bolt
closed with no barrel installed.
25
hold the bolt handle with one hand while depressing the
carrier release button with the other (See Figure 15). Use
extreme caution. If you allow the bolt assembly to slam
closed with the barrel removed you can damage the
receiver and affect the function of your gun.
5. Place your gun with the trigger guard facing up, on a
suitable surface that will protect the receiver finish and
stock.
6. With the gun inverted, (trigger guard up) use a drive
punch or similar object to push inward on the trigger
group pins, using caution not to scratch the receiver (see
Figure 16). In the field the end of the bolt slide link can
be used to start the two pins out (of course you will have
to remove the bolt assembly — described below — before
doing this). Trigger group pins may be removed from
either side of the receiver. Push the trigger group pins
clear through to the other side of the receiver. Once the
pins are started out they can be pulled the rest of the way
out using your fingers (See Figure 17).
7. Grasp the trigger group and pull it up and out of the
receiver (See Figure 18).
8. Perform any cleaning of the parts and receiver cavity
as necessary.
DO NOT DISASSEMBLE THE TRIGGER GROUP
BEYOND THIS POINT. ANY MAINTENANCE
BEYOND THIS POINT SHOULD BE DONE BY
A COMPETENT GUNSMITH, OUR SERVICE
CENTER OR A U.S. REPEATING ARMS
AUTHORIZED REPAIR CENTER.
FIGURE 16 FIGURE 17
Pull the pins completely free from
the receiver with your fingers.
Push out the trigger guard
pins. Be careful not to mar
or scratch the receiver.
HOW TO REASSEMBLE THE TRIGGER GROUP —
1. Make Sure the bolt is in the forward position. Use
extreme caution. If you allow the bolt assembly to slam
closed with the barrel removed you can damage the
receiver and affect the function of your gun. If the bolt is
not already forward, carefully and slowly lower it to the
closed position as explained previously.
2. Insert the trigger group back into the receiver. The
holes in the trigger group should line up with holes on
each side of the receiver. (If the hammer on the trigger
assembly has been inadvertently uncocked during cleaning , it helps assembly if it is recocked. Do this by simply
by pulling it back fully until it locks rearward.)
3. Reinsert the trigger guard pins, pushing them in with
your hand or gently tapping them into place with a plastic
or wooden mallet, again using caution not to scratch the
receiver.
4. Complete assembly by installing the gas system, barrel
and forearm as explained under “Initial
Assembly/Takedown.”
BOLT DISASSEMBLY/REASSEMBLY
The bolt can be removed for normal maintenance or if
the action becomes excessively dirty or wet. The Super X2
is designed to allow full disassembly of the bolt assembly
in the field, without any tools. Although it is possible
to remove the bolt with the trigger group in place, the
correct procedure when removing the bolt is to always
remove the trigger group first. Removing the bolt without
removing the trigger group could allow the bolt to spring
out the front of the receiver, damaging or losing parts or
causing injury to you or others.
HOW TO REMOVE THE BOLT ASSEMBLY —
1. First, always remove the barrel assembly as explained
earlier in this manual under “Initial
Assembly/Takedown.”
2. VERY IMPORTANT: As explained previously, with
the barrel removed you MUST carefully and slowly lower
the bolt forward from the open position to the forward,
26
FIGURE 18
Remove the trigger group
from the receiver.
27
closed position. To do this hold the bolt handle with one
hand while depressing the carrier release button with the
other to prevent slamming the bolt forward and damaging
the receiver.
3. Remove the trigger group as explained under “Trigger
Group Disassembly/Reassembly.”
4. Remove the bolt handle by pulling the handle outward,
to the right, away from the bolt. It is held in place with a
ball-detent system that may take a little effort to pull free.
5. Slide the bolt and bolt slide forward and out of the
front of the receiver (See Figure 19).
6. The bolt and bolt slide can be separated for cleaning
(See Figure 20). Perform any cleaning of the bolt and
receiver cavity as necessary.
DO NOT DISASSEMBLE THE BOLT ASSEMBLY
BEYOND THIS POINT.
HOW TO REINSTALL THE BOLT ASSEMBLY —
Under usual conditions, the trigger group should also
have been removed at this point. Reinstallation of the
bolt assembly is somewhat easier with the trigger group
removed.
1. Reassemble the bolt and bolt slide as shown
(See Figure 21).
2. Place the bolt assembly back in the receiver, bolt slide
link end first (See Figure 22). Line the rails on the bolt
slide with slots in the bottom of the receiver.
3. Guide the bolt slide link into its socket in the recoil
FIGURE 19
FIGURE 20
Separate the bolt and bolt slide for easy cleaning.
Remove the bolt assembly forward,
out the front of the receiver.
Bolt
Bolt Slide
28
spring follower (See Figure 23). The socket can be seen at
the rear of the receiver cavity. It is the cupped-shaped
part that forms a recess for the bolt side link to rest in.
Become familiar with how the slide fits into the socket. It
helps to keep the receiver pointing slightly upward to
assure that the bolt slide link does not come out of the
recoil spring follower until the barrel is reinstalled. VERY
IMPORTANT: If when your gun is fully assembled it will
not function properly and the action will not open, the
bolt slide link is likely not properly in place in the recoil
spring follower socket. (It is possible, with practice to fit
the bolt slide link into the recoil spring follower even
with the trigger group installed, by holding the gun
vertically and aligning the link into the socket while
looking through the bolt handle slot on the right side of
the receiver. This is handy if you are simply reattaching
the barrel assembly after storage and the bolt has inadvertently moved forward and the bolt slide link has come out
of the socket.)
4. Replace the bolt handle by pushing it in (cupped side
toward the front) until it engages in the ball-detent. (See
Figure 24).
5. Again, observe that the bolt slide link and recoil spring
follower are properly engaged. (You can also confirm this
by pulling back a bit on the bolt handle. You will feel the
recoil spring compress as you pull back. Do this very slowly,
and make sure you control the bolt as the bolt slide link
may not be properly seated into the recoil spring follower
socket. Repeat step 3 above, making sure that they are
FIGURE 22
When installing the bolt assembly, make sure you install
it link end first. Line up the rails with the receiver.
FIGURE 21
Reassemble the bolt and bolt slide.
29
installed correctly. Remember the bolt cannot lock rearward with the trigger group removed.
6. Reinstall the trigger group as explained previously (if it
was removed).
7. With the trigger group installed, pull the bolt fully back
until it locks in the rearward position.
TO PREVENT SLAMMING THE BOLT FORWARD
AND DAMAGING THE RECEIVER, DO NOT
PRESS THE CARRIER RELEASE BUTTON
UNTIL INSTALLATION IS COMPLETE.
8. Replace the gas system, barrel and forearm as explained
previously.
9. Again, work the bolt fully to the rear until it locks
open. If it will not complete its rearward movement and
will not lock rearward, you likely have not properly
installed the bolt slide link into its socket in the recoil
spring follower. Refer to step 3 above.
10. With all parts installed (including the barrel) your
Super X2 is fully assembled. It is now allowable to lock
the bolt rearward then let is slam forward (closed) by
pressing the carrier release button. Be sure to always
keep your fingers clear of the ejection port when closing
the action.
FIGURE 23
FIGURE 24
Carefully guide the
bolt slide link into its
socket in the recoil
spring follower.
This must be done
correctly or your gun
will not function.
Replace the bolt handle by
pushing it in until it snaps into
place in the spring-detent.
You can feel it snap into position.
Bolt Slide Link
Socket in the recoil
spring follower
30
INVECTOR®PLUS CHOKE TUBE SYSTEM
The Super X2 is fitted with one of the most popular and
universally accepted choke tube systems on the market:
Invector-Plus. Your Super X2 Shotgun is specially
designed for this system only. This means:
• It has a back-bored barrel.
• It is threaded to accept Invector-Plus choke tubes only.
The Invector-Plus system allows you to configure your
Super X2 for the pattern and/or choke constriction your
hunt demands. The system gives you the most highly
engineered choke tapers — designed to produce the best
possible patterns for target and field situations. Plus, it is
extremely easy to switch choke constrictions to match
your shooting conditions. Invector-Plus tubes are fully
steel and lead shot compatible. Most Invector-Plus choke
tubes fit flush with the muzzle when installed. A special
choke tube wrench is provided to remove and tighten
these tubes.
Invector-Plus choke tubes are NOT interchangeable with
any other choke tubes on the market including chokes
listed as "Standard Invector" or Winchester’s current line
of "WinChoke" choke tubes.
USE ONLY CHOKE TUBES MARKED INVECTOR
PLUS IN YOUR SUPER X2. USE ONLY THE
APPROPRIATE GAUGE OF INVECTOR PLUS
CHOKE TUBES AS MARKED ON YOUR
SUPER X2 SHOTGUN.
Failure to follow these warnings may damage your gun
and cause injury to yourself and others. A special "Plus"
choke tube wrench is provided to remove and tighten
Invector-Plus choke tubes.
DO NOT FIRE THIS SHOTGUN WITHOUT
HAVING AN INVECTOR CHOKE TUBE
INSTALLED. PERMANENT DAMAGE MAY
RESULT TO THE THREADS.
CAUTION: WHENEVER HANDLING ANY SHOTGUN FOR THE PURPOSE OF REMOVING OR
INSTALLING A CHOKING DEVICE, MAKE
ABSOLUTELY CERTAIN THE GUN IS FULLY
UNLOADED, AND THE BOLT OR BREECH IS
OPEN! NEVER ATTEMPT TO REMOVE OR
INSTALL A SHOTGUN CHOKING DEVICE ON
A LOADED FIREARM!
TUBE REMOVAL —
1.
UNLOAD YOUR SUPER X2 SHOTGUN
FULLY. INSPECT THE CHAMBER, FEED
MECHANISM AND MAGAZINE TO MAKE SURE
THEY DO NOT CONTAIN ANY SHELLS.
31
2. Open the action, locking it rearward, and place the
“safety” in the “on safe” position.
3. Use the Invector Plus wrench to loosen the tube, turning it counterclockwise. Finger twist the tube the rest of
the way out of the barrel.
TUBE INSTALLATION —
1.
UNLOAD YOUR SUPER X2 SHOTGUN
FULLY. INSPECT THE CHAMBER, FEED
MECHANISM AND MAGAZINE TO MAKE SURE
THEY DO NOT CONTAIN ANY SHELLS.
2. Open the action, locking it rearward, and place the
“safety” in the “on safe” position.
3. Before installing a tube, check the internal choke tube
threads in the muzzle, as well as the threads on the
Invector-Plus choke tube to be sure they are clean.
Lightly oil the threads with a high quality light weight oil.
4. Using your fingers, screw the appropriate tube into the
muzzle end of the barrel, tapered end first, notched end
outward. When it becomes finger tight, use the InvectorPlus choke tube wrench to firmly seat the tube.
THE INVECTOR PLUS CHOKE TUBE SHOULD
BE PERIODICALLY CHECKED TO ASSURE
THAT IT IS TIGHT AND FIRMLY SEATED.
BEFORE CHECKING, FOLLOWING THE SAFETY
GUIDELINES OUTLINED ABOVE.
SELECTING THE CORRECT INVECTOR-PLUS TUBE —
The Invector-Plus choke system is fully compatible with
factory lead or steel shot loads. The conversion chart
includes both lead and steel shot information. Lead and
steel shot perform differently in tubes with the same
choke constriction. For this reason, both lead and steel
designations have proven necessary. In fact, even larger
steel shot diameters result in different patterns than smaller steel shot sizes. Each designation is inscribed on each
choke tube.
To help you choose the correct choke tube for each target
shooting and hunting situation, all Invector-Plus choke
tubes are inscribed on the side with abbreviations for the
patterns they produce with both lead and steel shot.
Each tube also features identification notches located on
the top rim of each tube (see Figure 25 and 26). These
notches are a code to allow you to determine the choke
designation while the tube is installed. Rim notches refer
specifically to lead shot. You will need to use the chart
below to cross-reference from lead to steel, and determine
the appropriate tubes for your ammunition and
hunting/shooting situation.
CHOKE TUBE RIM CODES AND PATTERNING
Rim Pattern With Pattern With
Notches Lead Shot Steel Shot
Knurled** X-Full Turkey **
I Full *
II Imp. Modified Full
1
III Modified Full
1
IIII Imp. Cylinder Modified
IIIII Skeet Imp. Cylinder
No Notches Cylinder Cylinder
•
Not for use with steel shot. Using an over-tight choke constriction
with steel shot will result in an ineffective “blown” pattern.
** Extra Full Special with knurled rim. Do not use with steel shot.
1
When more than one choke designation is listed for a given steel
shot pattern, use the more open choke listed for high velocity, larger
shot size steel loads.
32
FIGURE 26
Extra Full Turkey Special
No rim notch code. Knurled extension protrudes beyond muzzle.
Large notches are for choke tube wrench.
FIGURE 25
Small notches are the choke code.
Large notches are for the choke tube wrench.
Tube Notch Codes (Lead shot designations)
1 Notch: Full
2 Notches:
Improved Modified
3 Notches: Modified
4 Notches:
Improved Cylinder
5 Notches: Skeet
No Notches: Cylinder
USE OF EXTRA BARRELS
A good way to extend the utility and usefulness of your
new Super X2 is with an extra barrel. All Winchester
Super X2 semi-auto shotgun barrels are completely interchangeable within gauge and chamber length. No special
fitting is required.
Some important restrictions must be observed:
1) Never use a barrel with a 3 1/2” chamber in a Super X2
designed for barrels with a 3” chamber.
2) Never use a barrel with a 3” chamber in a Super X2
designed for barrels with a 3 1/2” chamber.
3) Never use any other barrel from any other manufacturer
on your Super X2. Some other brands may seem similar,
but the barrels are not interchangeable.
5) Never use any barrel from a Winchester shotgun made
in the past, including barrels for the original Super X
Model 1 shotgun.
FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN INJURY TO YOURSELF OR
OTHERS.
CLEANING AND MAINTENANCE SUGGESTIONS
Your Super X2 will function better and more reliably over
a longer period of time if it is properly maintained and
kept clean.
BEFORE PERFORMING ANY CLEANING
PROCEDURES, ALWAYS MAKE CERTAIN
THERE ARE NO SHELLS IN THE CHAMBER,
MAGAZINE OR ACTION/FEED AREAS.
You should clean your Super X2 after every day
of shooting and more often if it becomes excessively dirty.
A minimum cleaning includes wiping down the action
and oiling key parts. Most regular maintenance will also
include cleaning the barrel. If you encounter a function
problem (tight action when working the
forearm) be sure to give your gun a thorough cleaning to
see if it solves the problem before seeking the services of
our service facility or a competent gunsmith. To clean
your firearm, adhere to the following general guidelines.
CLEANING PROCEDURES —
BE CERTAIN YOUR GUN’S CHAMBER AND
MAGAZINE ARE UNLOADED. ALWAYS WEAR
PROTECTIVE SAFETY GLASSES DURING
ALL CLEANING PROCEDURES. KEEP
AMMUNITION AWAY FROM THE CLEANING
33
AREA. DO NOT TEST THE FUNCTION OF
YOUR FIREARM WITH LIVE AMMUNITION.
ALWAYS PLACE THE SAFETY IN “ON SAFE”
POSITION BEFORE BEGINNING ANY CLEANING PROCEDURE.
1. Use a cleaning rod with a tip and patch suitable for the
size of your Super X2’s bore. Make sure the patch is large
enough for a snug fit in the bore. Insert the rod and patch
into the barrel at the receiver end and run it back and
forth several times.
2. Inspect the chamber and bore for lead and powder
fouling. A normal amount of powder residue can be
expected and is not serious. It can usually be removed by
repeating step one, using a patch saturated with solvent.
If or when fouling should become heavy, it can be
removed with a brass bore brush. Dip or spray the brush
with solvent and scrub the chamber and bore until the
fouling is removed. To prevent brass bristles from breaking
off, the brush should be pushed completely through the
bore before being withdrawn.
3. After fouling has been removed the bore should be
wiped dry. Then pass a slightly oiled patch through the
bore, for preservation. A fine, light gun oil is recommended.
4. Wipe all exposed metal surfaces of the receiver, forearm
and barrel with a clean rag. Finger marks should be
removed because they provide a place where moisture can
accumulate. Any dried oil in the receiver area should also
be removed.
5. Lightly oil your gun at the points described under
“Oiling the Action” explained earlier in this manual.
Ordinary good judgment will, of course, indicate that the
metal of the gun should receive a light film of oil any time
the gun has been exposed to weather or handling. This
is very important and must be done with every gun —
even stainless steel models. Remember, the polished, finely
fitted surfaces of the receiver and action mechanisms must
always have a thin film of oil. Make sure that the surfaces
of the breech bolt are especially clean and lightly oiled
with a high quality gun oil.
6.
INSPECT THE BARREL AND CHAMBER.
MAKE CERTAIN THAT NO PATCHES HAVE
BEEN INADVERTENTLY LEFT IN THEM.
REMOVE ANY THAT REMAIN.
7. Wipe all wood surfaces with a soft cloth.
8. When transporting only, store your Super X2 in a quality
protective case to prevent scratches and dents. Store in a
dry place to prevent corrosion. Store away from children.
MAKE SURE YOUR SHOTGUN IS UNLOADED
AND ALWAYS STORE AMMUNITION
SEPARATELY.
34
DO NOT TAKE YOUR GUN’S ACTION APART
BEYOND WHAT IS EXPLAINED IN THIS MANUAL.
This is a specialized, finely fitted mechanism; any attempt
to disassemble the trigger group or bolt mechanism may
mar it for life. It is unnecessary, and may do damage to
the inner mechanism, to disassemble these components
for routine cleaning and oiling. Of course, misfortunes
(such as dropping your gun in water) require appropriate
attention, and in such circumstances we recommend you
immediately take your gun to a competent gunsmith.
CLEANING THE ACTION AND TRIGGER GROUP —
1. When the action becomes excessively dirty, remove the
trigger group and bolt assembly from the receiver as
explained under “Bolt Disassembly/Reassembly.” Clean
with a good quality light oil, a gun solvent or spray
“scrub” as necessary, using an old toothbrush to loosen
any caked-on grime. Wipe the receiver cavity clean.
Lightly oil the cavity and wipe it dry. No further disassembly is required for cleaning.
2. Reassemble as explained previously and wipe all exposed
metal surfaces with an oiled cloth, making sure to wipe
clean all finger marks where moisture will accumulate.
3. The barrel and action should be inspected to assure
that all cleaning patches have been removed and not
inadvertently left in the barrel or action.
CLEANING THE GAS SYSTEM —
1. Remove the gas piston and piston sleeve from the
magazine tube. Do no attempt to disassemble gas piston
components, it is not necessary for good maintenance and
risks loosing parts and damaging your gun. Spray the
magazine tube with a good quality powder solvent and
wipe clean.
2. Spray the piston and bracket with a good quality powder solvent. Brush them thoroughly to remove any
deposits (an old toothbrush is ideal). Spray the inside and
wipe off any buildup.
NEVER USE A STEEL BRUSH
ON ANY OF THE GAS SYSTEM COMPONENTS.
3. Complete the cleaning of the gas system by applying
a very light film of gun oil to all parts for protection and
lubrication
CLEANING THE MAGAZINE SYSTEM —
It is a good idea — especially if your gun becomes excessively dirty or very wet — to occasionally clean the
magazine system. Remove the magazine spring retainer,
three shot plug, magazine spring and magazine follower by
following the instructions under “Magazine Plug” detailed
earlier in this manual.
Clean the inside of the tube using a rod and patch just as
you would clean a barrel. Carefully wipe off the spring and
3-shot adapter. Very lightly oil each component. Reinstall
all parts as explained earlier.
35
CLEANING THE INVECTOR-PLUS CHOKE SYSTEM —
1. Do not use a brass brush to clean your barrel unless a
choke tube is installed in the barrel. Bristles could break
off and lodge in the threads, making installation and
removal difficult.
2. Regularly remove your gun’s tube in order to clean and
oil the threads inside the barrel, as well as on the choke
tube itself. This will protect the threads from being
damaged and also prevent a dirt build-up that would cause
the choke tube to become difficult to remove from the
barrel. Clean the threads with solvent and a small, soft
brush like a toothbrush. Wipe completely clean and leave
a thin film of clean oil on the threads: both on the tube
and in the barrel. The threads of the choke tube and the
internal threads of the barrel should be cleaned after each
use and before the installation of a tube.
3. Be careful when removing/installing a tube. Use the
specially designed wrench. Damage can result to both
choke tube and barrel when attempting to remove sticky
choke tubes.
4. Never fire your shotgun or run cleaning tools through
the barrel of any choke-tubed gun without having the
choke tube installed.
OTHER CLEANING SUGGESTIONS —
• Never pour large quantities of oil into the receiver or
other parts. It can drain down to the wood and soften it
— and cause permanent damage and loosening of the
stock.
• After extended periods of heavy use, your shotgun
should be taken to a qualified gunsmith to have the action
disassembled for professional cleaning and lubrication.
• Camouflage and synthetic-stocked models require the
same care and cleaning as non-camouflage. Use the same
oils and solvents as described previous in this manual.
NEVER ATTEMPT TO TAKE YOUR SUPER X2
APART FURTHER THAN EXPLAINED IN
THIS MANUAL.
This is a specialized, finely fitted mechanism. You may
permanently mar it by attempting to disassemble the
inner mechanism assemblies. If further disassembly for
service or cleaning is required, take your gun to a U. S.
Repeating Arms Company recommended Authorized
Repair Center or a competent gunsmith as explained
under “Service or Repair.”
36
ORDERING PARTS
To order parts, please write our parts department and
furnish the following: your name, address, and telephone
number. Also specify the caliber, model, serial number
and grade of your Winchester gun. When we receive your
request, we will send an order form and a parts breakdown
with prices.
Write to:
Parts Department
U.S. Repeating Arms Company, Inc.
344 Winchester Avenue
New Haven, Connecticut 06511-1970
CAUTION: PARTS ARE MADE FOR
WINCHESTER BRAND GUNS MANUFACTURED
BY OR FOR U.S. REPEATING ARMS
COMPANY, INC., AND SHOULD NOT BE USED
IN OTHER GUNS EVEN THOUGH MODELS
MAY BE SIMILAR. IMPROPERLY FITTED
PARTS MAY BE DANGEROUS.
SERVICE OR REPAIR
If your Winchester firearm should ever need repair or
service, please utilize one of the world-wide network of
U.S. Repeating Arms Company A
uthorized Repair
C
enters (ARC) for Winchester firearms. A list of ARCs is
packaged with your new gun. If you have any questions
about how to obtain service, or to obtain a new list of
ARCs, call us at:
1-203-789-5000
37
QUESTIONS
If you have other questions about Winchester rifles and
shotguns, call or write our Customer Service Department:
Customer Service
U.S. Repeating Arms Company, Inc.
275 Winchester Avenue
Morgan, Utah 84050-9333
Phone: 1-800-945-5237
WINCHESTER-GUNS.COM
U.S. Repeating Arms Company offers an information
resource for you on the world wide web.
• List of authorized repair centers.
• Customer service information.
• Answers to many technical and historical questions.
• Links to helpful sites.
Go to: www.winchester-guns.com
38
39
U.S. Repeating Arms Company, Inc.
344 Winchester Avenue
New Haven, Connecticut, U.S.A. 06511-1970
Administrative Offices:
275 Winchester Avenue, Morgan, Utah 84050-9333
Licensee
Winchester trademarks licensed from Olin Corporation.
Loading...