Winchester B2332484, B2332487, B2332488, B2332489, B2332486 User Manual

INSTALLATION MANUAL

SINGLE STAGE ECM
RESIDENTIAL GAS FURNACES

MODELS: TM9E Series
(95% AFUE Multi-position)

LIST OF SECTIONS

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

ELECTRICAL POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CONDENSATE PIPING AND FURNACE

VENTING CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

LIST OF FIGURES

Duct Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Furnace and Coil Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Combustible Floor Base Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Horizontal Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Typical Attic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Typical Suspended Furnace / Crawl Space Installation . . . . . . . . . . . 7

Downflow Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Side Return Cutout Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Left Side Supply Gas Pipe Arrangement . . . . . . . . . . . . . . . . . . . . . . 9

Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Thermostat Chart - 1H/1C - Single Stage Furnace

(STD-ECM) - Single Stage Air Conditioner . . . . . . . . . . . . . . . . . . . 12

Thermostat Chart - 1H/2C - Single Stage Furnace

(STD-ECM) - Single Stage Air Conditioner . . . . . . . . . . . . . . . . . . . 12

Typical. Condensate drain, vertical installation . . . . . . . . . . . . . . . . 13

Upflow Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

COMBUSTION AIR and VENT SYSTEM . . . . . . . . . . . . . . . . . . . .19

START-UP AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . .27

SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

NORMAL OPERATION AND DIAGNOSTICS . . . . . . . . . . . . . . . . .33

REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

START UP SHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Downflow Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Horizontal Left Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Horizontal Right Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Elbow Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Home Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Termination Configuration - 1 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . .23

Termination Configuration - 2 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . .23

Termination Configuration - 2 Pipe Basement . . . . . . . . . . . . . . . . .23

Double Horizontal Combustion Air Intake and Vent Termination . . .24

Double Vertical Combustion Air Intake and Vent Termination . . . . . 24

Downward Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Direct Vent Air Intake Connection and Vent Connection . . . . . . . . .24

Combustion Airflow Path Through The Furnace Casing . . . . . . . . .25

Ambient Combustion Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Attic and Crawl Space Combustion Air Termination . . . . . . . . . . . . .27

Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Reading Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Furnace Control Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

LIST OF TABLES

Unit Clearances to Combustibles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Cabinet and Duct Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Recommended Filter Sizes (High Velocity 600 FPM) . . . . . . . . . . . . 8

Nominal Manifold Pressure - High Fire . . . . . . . . . . . . . . . . . . . . . . 10

Ratings & Physical / Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maximum Equivalent Pipe Length . . . . . . . . . . . . . . . . . . . . . . . . . . 20

High Altitude Pressure Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Elbow Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Equivalent Length of Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

These high efficiency, compact units employ induced combustion, reli­able hot surface ignition and high heat transfer aluminized tubular heat
exchangers. The units are factory shipped for installation in upflow or
horizontal applications and may be converted for downflow applica­tions.

Johnson Controls Unitary Products 1083163-UIM-J-0918

Combustion Air Intake and Vent Connection

Size at Furnace (All Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Estimated Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Unconfined Space Minimum Area . . . . . . . . . . . . . . . . . . . . . . . . . .25

Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Gas Rate (CU FT/HR) at Full Input . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Inlet Gas Pressure Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Nominal Manifold Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Blower Performance CFM - Any Position (without filter) . . . . . . . . . . 32

These furnaces are designed for residential installation in a basement,
closet, alcove, attic, recreation room or garage and are also ideal for
commercial applications. All units are factory assembled, wired and
tested to assure safe dependable and economical installation and oper­ation.

These units are Category IV listed and may not be common vented with
another gas appliance as allowed by the National Fuel Gas Code.

1083163-UIM-J-0918

SECTION I: SAFETY

This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.

Understand and pay particular attention to the signal words DANGER,

WARNING, or CAUTION.

DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation, which, if not

avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property dam­age.

!

WARNING

Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.

Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Failure to carefully read and

follow all instructions in this manual can result in furnace mal­function, death, personal injury and/or property damage. Only a

qualified contractor, installer or service agency should install this
product.

SPECIFIC SAFETY RULES AND PRECAUTIONS

1. Only Natural gas or Propane (LP) gas are approved for use with
this furnace.

2. Install this furnace only in a location and position as specified in
these instructions.

3. A gas-fired furnace for installation in a residential garage must be
installed as specified in these instructions.

4. Provide adequate combustion and ventilation air to the furnace
space as specified in these instructions.

5. Combustion products must be discharged outdoors. Connect this
furnace to an approved vent system only, as specified in SECTION
VII, "COMBUSTION AIR and VENT SYSTEM" of these instruc­tions.

6. Test for gas leaks as specified in these instructions.

9. It is permitted to use the furnace for heating of buildings or struc­tures under construction where the application and use must com­ply with all manufacturer’s installation instructions including:

• Proper vent installation;

• Furnace operating under thermostatic control;

• Return air duct sealed to the furnace;

• Air filters in place;

• Set furnace input rate and temperature rise per rating plate mark-

ing;

• Means for providing outdoor air required for combustion;

• Return air temperature maintained between 55ºF (13ºC) and

80ºF (27ºC);

• The air filter must be replaced upon substantial completion of

the construction process;

• Clean furnace, duct work and components upon substantial com-

pletion of the construction process, and verify furnace-operating
conditions including ignition, input rate, temperature rise and
venting, according to the manufacturer’s instructions.

10. When installed in a non-HUD-Approved Modular Home or building
constructed on-site, combustion air shall not be supplied from occu­pied spaces.

11. The size of the unit should be based on an acceptable heat loss
calculation for the structure. ACCA, Manual J or other approved
methods may be used.

12. When moving or handling this furnace prior to installation, always
leave the doors on the furnace to provide support and to prevent
damage or warping of the cabinet. When lifting the furnace by the
cabinet, support the ends of the furnace rather than lifting by the
cabinet flanges at the return air openings (bottom or sides) or sup­ply air opening.

13. When lifting the furnace, it is acceptable to use the primary heat
exchanger tubes as a lifting point provided that the tubes are lifted
at the front of the heat exchangers where attached to the vestibule
panel. Do not use the top return bend of the heat exchangers as lift­ing points as the tubes may shift out of position or their location
brackets/baffles.

IMPORTANT

During installation, doors should remain on the furnace when
moving or lifting.

SAFETY REQUIREMENTS

!

WARNING

FIRE OR EXPLOSION HAZARD
Failure to follow the safety warnings exactly could result in serious

injury, death or property damage.
Never test for gas leaks with an open flame. Use a commercially

available soap solution made specifically for detection of leaks to
check all connections. A fire or explosion may result causing property
damage, personal injury or loss of life.

7. Always install the furnace to operate within the furnace’s intended
temperature rise range. Only connect the furnace to a duct system
which has an external static pressure within the allowable range, as
specified on the furnace rating plate.

8. When a furnace is installed so that supply ducts carry air circulated
by the furnace to areas outside the space containing the furnace,
the return air shall also be handled by duct(s) sealed to the furnace
casing and terminating outside the space containing the furnace.

This product must be installed in strict compliance with the installation
instructions and any applicable local, state, and national codes
including, but not limited to building, electrical, and mechanical codes.

• Refer to the unit rating plate for the furnace model number, and
then see the dimensions page of this instruction for return air ple­num dimensions in Figure 13. The plenum must be installed
according to the instructions.

• Provide clearances from combustible materials as listed under
Clearances to Combustibles.

• Provide clearances for servicing ensuring that service access is
allowed for both the burners and blower.

• These models ARE NOT CSA listed or approved for installation
into a HUD Approved Modular Home or a Manufactured
(Mobile) Home.

• This furnace is not approved for installation in trailers or recre­ational vehicles.

!

CAUTION

2 Johnson Controls Unitary Products

1083163-UIM-J-0918

• Furnaces for installation on combustible flooring shall not be
installed directly on carpeting, tile or other combustible material
other than wood flooring.

• Check the rating plate and power supply to be sure that the electri­cal characteristics match. All models use nominal 115 VAC, 1
Phase, 60-Hz power supply. DO NOT CONNECT THIS APPLI­ANCE TO A 50-Hz POWER SUPPLY OR A VOLTAGE ABOVE
130 VOLTS.

• Furnace shall be installed so the electrical components are pro­tected from water.

• Installing and servicing heating equipment can be hazardous due
to the electrical components and the gas fired components. Only
trained and qualified personnel should install, repair, or service
gas heating equipment. Untrained service personnel can perform
basic maintenance functions such as cleaning and replacing the
air filters. When working on heating equipment, observe precau­tions in the manuals and on the labels attached to the unit and
other safety precautions that may apply.

COMBUSTION AIR QUALITY
(LIST OF CONTAMINANTS)

!

WARNING

The furnace area must not be used as a broom closet or for any other
storage purposes, as a fire hazard may be created. Never store items
such as the following on, near or in contact with the furnace.

1. Spray or aerosol cans, rags, brooms, dust mops, vacuum
cleaners or other cleaning tools.

2. Soap powders, bleaches, waxes or other cleaning com­pounds; plastic items or containers; gasoline, kerosene, ciga­rette lighter fluid, dry cleaning fluids or other volatile fluid.

3. Paint thinners and other painting compounds.

4. Paper bags, boxes or other paper products

Never operate the furnace with the blower door removed. To do
so could result in serious personal injury and/or equipment
damage.

The furnace requires OUTDOOR AIR for combustion when the furnace
is located in any of the following environments.

• Buildings with indoor pools

• Chemical exposure

• Commercial buildings

• Furnaces installed in hobby or craft rooms

• Furnaces installed in laundry rooms

• Furnaces installed near chemical storage areas

• Restricted Environments

The furnace requires OUTDOOR AIR for combustion when the furnace
is located in an area where the furnace is being exposed to the follow­ing substances and / or chemicals.

• Antistatic fabric softeners for clothes dryers

• Carbon tetrachloride

• Cements and glues

• Chlorine based swimming pool chemicals

• Chlorinated waxes and cleaners

• Cleaning solvents (such as perchloroethylene)

• De-icing salts or chemicals

• Halogen type refrigerants

• Hydrochloric acid

• Masonry acid washing materials

• Permanent wave solutions

• Printing inks, paint removers, varnishes, etc.

• Water softening chemicals

When outdoor air is used for combustion, the combustion air intake duct
system termination must be located external to the building and in an
area where there will be no exposure to the substances listed above.

CODES AND STANDARDS

Follow all national, local codes and standards in addition to this installa­tion manual. The installation must comply with regulations of the serv­ing gas supplier, local building, heating, plumbing, and other codes. In
absence of local codes, the installation must comply with the national
codes listed below and all authorities having jurisdiction.

In the United States and Canada, follow all codes and standards for the
following, using the latest edition available:

STEP 1 - Safety

• US: National Fuel Gas Code (NFGC) NFPA 54/ANSI Z223.1 and
the Installation Standards, Warm Air Heating and Air Conditioning
Systems ANSI/NFPA 90B

• CANADA: CAN/CGA-B149.1 National Standard of Canada. Natu­ral Gas and Propane Installation Codes (NSCNGPIC)

STEP 2 - General Installation

• US: Current edition of the NFGC and NFPA 90B. For copies, con­tact the

National Fire Protection Association Inc.
Batterymarch Park
Quincy, MA 02269

or for only the NFGC, contact the

American Gas Association,
400 N. Capital, N.W.
Washington DC 20001

or www.NFPA.org

• CANADA: NSCNGPIC. For a copy contact:

Standard Sales, CSA International
178 Rexdale Boulevard
Etobicoke, (Toronto) Ontario Canada M9W 1RS

STEP 3 - Combustion and Ventilation Air

• US: Section 5.3 of the NFGC, air for Combustion and Ventilation

• CANADA: Part 7 of NSCNGPIC, Venting Systems and Air Supply
for Appliances

STEP 4 - Duct Systems

• US and CANADA: Air Conditioning Contractors Association
(ACCA) Manual D, Sheet Metal and Air Conditioning Contractors
Association National Association (SMACNA), or American Society
of Heating, Refrigeration, and Air Conditioning Engineers
(ASHRAE) 1997 Fundamentals Handbook Chapter 32.

STEP 5 - Acoustical Lining and Fibrous Glass Duct

• US and CANADA: Current edition of SMACNA and NFPA 90B as
tested by UL Standard 181 for Class I Rigid Air Ducts

STEP 6 - Gas Piping and Gas Pipe Pressure Testing

• US: NFGC; chapters 2, 3, 4, & 9 and National Plumbing Codes

• CANADA: NSCNGPIC Part 5

STEP 7 - Electrical Connections

• US: National Electrical Code (NEC) ANSI/NFPA 70

• CANADA: Canadian Electrical Code CSA C22.1

These instructions cover minimum requirements and conform to exist­ing national standards and safety codes. In some instances these
instructions exceed certain local codes and ordinances, especially
those who have not kept up with changing residential and non-HUD
modular home construction practices. These instructions are required
as a minimum for a safe installation.

Johnson Controls Unitary Products 3

1083163-UIM-J-0918

FOR FURNACES INSTALLED IN THE COMMON­WEALTH OF MASSACHUSETTS ONLY

For all side wall horizontally vented gas fueled equipment installed in
every dwelling, building or structure used in whole or in part for resi­dential purposes, including those owned or operated by the Com­monwealth and where the side wall exhaust vent termination is less
than seven (7) feet above finished grade in the area of the venting,
including but not limited to decks and porches, the following require­ments shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At
the time of installation of the side wall horizontal vented gas
fueled equipment, the installing plumber or gasfitter shall
observe that a hard wired carbon monoxide detector with an
alarm and battery back-up is installed on the floor level where the
gas equipment is to be installed. In addition, the installing
plumber or gasfitter shall observe that a battery operated or hard
wired carbon monoxide detector with an alarm is installed on
each additional level of the dwelling, building or structure served
by the side wall horizontal vented gas fueled equipment. It shall
be the responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of hard
wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent floor
level.

b. In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply with
the above requirements; provided, however, that during
said thirty (30) day period, a battery operated carbon mon­oxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon
monoxide detector as required in accordance with the above pro­visions shall comply with NFPA 720 and be ANSI/UL 2034 listed
and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be perma­nently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heat­ing appliance or equipment. The sign shall read, in print size no
less than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall
horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes car­bon monoxide detectors and signage installed in accordance
with the provisions of 248 CMR 5.08(2)(a)1 through 4.

INSPECTION

As soon as a unit is received, it should be inspected for possible dam­age during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s freight bill. A separate request for
inspection by the carrier’s agent should be made in writing. Also, before
installation, the unit should be checked for screws or bolts which may
have loosened in transit. There are no shipping or spacer brackets
which need to be removed from the interior of this unit.

FURNACE LOCATION AND CLEARANCES

The furnace shall be located using the following guidelines:

1. Where a minimum amount of air intake/vent piping and elbows will
be required.

2. As centralized with the air distribution as possible.

3. Where adequate combustion air will be available (particularly when
the appliance is not using outdoor combustion air).

4. Where it will not interfere with proper air circulation in the confined
space.

5. Where the outdoor vent terminal will not be blocked or restricted.
Refer to “VENT CLEARANCES” located in SECTION VII of these
instructions. These minimum clearances must be maintained in the
installation.

6. Where the unit will be installed in a level position with no more than
1/4” (6.4 mm) slope side-to-side and front-to-back to provide proper
condensate drainage.

Installation in freezing temperatures:

1. Furnace shall be installed in an area where ventilation facilities pro­vide for safe limits of ambient temperature under normal operating
conditions. Ambient temperatures must not fall below 32°F (0°C)
unless the condensate system is protected from freezing.

!

WARNING

Improper installation in an ambient below 32ºF (0.0° C) could create a
hazard, resulting in damage, injury or death.

2. Do not allow return air temperature to be below 55ºF (13°C) for
extended periods. To do so may cause condensation to occur in the
main heat exchanger, leading to premature heat exchanger failure.

3. If this furnace is installed in an unconditioned space and an
extended power failure occurs, there will be potential damage to the
internal components. Following a power failure situation, do not
operate the unit until inspection and repairs are performed.

!

WARNING

Liquid anti-freeze will cause damage to internal plastic parts of this
furnace. DO NOT attempt to winterize the furnace using liquid

anti-freeze.

Clearances for access/service:

Ample clearances should be provided to permit easy access to the unit.
The following minimum clearances are recommended:

1. Twenty-four (24) inches (61 cm) between the front of the furnace
and an adjacent wall or another appliance, when access is required
for servicing and cleaning.

2. Eighteen (18) inches (46 cm) at the side where access is required
for passage to the front when servicing or for inspection or replace­ment of flue/vent connections.

In all cases, accessibility clearances shall take precedence over clear­ances for combustible materials where accessibility clearances are
greater.

Installation in a residential garage:

A gas-fired furnace for installation in a residential garage must be
installed so the burner(s) and the ignition source are located not less
than 18” (46 cm) above the floor, and the furnace must be located or
protected to avoid physical damage by vehicles.

Table 1:

Unit Clearances to Combustibles

Application Upflow Downflow Horizontal

Top 1" 0" 0"

Vent 0" 0" 0"

Rear 0" 0" 0"

Side 0" 0" 1"

Front* 0" 0" 0"

Floor Combustible

Closet Yes Yes Yes

Line Contact No No Yes

1. For combustible floors only when used with special sub-base.
* 24" clearance in front and 18" on side recommended for service access.
All furnaces approved for alcove and attic installation.

Combustible

1

Combustible

4 Johnson Controls Unitary Products

SECTION II: DUCTWORK

DUCTWORK GENERAL INFORMATION

The duct system’s design and installation must:

1. Handle an air volume appropriate for the served space and within
the operating parameters of the furnace specifications.

2. Be installed in accordance of National Fire Protection Association
as outlined in NFPA standard 90B (latest editions) or applicable
national, provincial, state, and local fire and safety codes.

3. Create a closed duct system. For residential and non-HUD Modular
Home installations, when a furnace is installed so that the supply
ducts carry air circulated by the furnace to areas outside the space
containing the furnace, the return air shall also be handled by a
duct(s) sealed to the furnace casing and terminating outside the
space containing the furnace.

4. Complete a path for heated or cooled air to circulate through the air
conditioning and heating equipment and to and from the condi­tioned space.

!

CAUTION

The indoor coil must be installed in the supply air duct, downstream of
the furnace. Cooled air may not be passed over the heat exchanger.

When the furnace is used with an indoor coil, the coil must be installed
parallel with, or in the supply air side of the furnace to avoid condensa­tion in the primary heat exchanger. When a parallel flow arrangement is
used, dampers or other means used to control airflow must be ade­quate to prevent chilled air from entering the furnace. If manually oper­ated, the damper must be equipped with means to prevent the furnace
or the air conditioner from operating unless the damper is in full heat or
cool position.

When replacing an existing furnace, if the existing plenum is not the
same size as the new furnace then the existing plenum must be
removed and a new plenum installed that is the proper size for the new
furnace. If the plenum is shorter than 12” (30.5 cm) the turbulent air flow
may cause the limit controls not to operate as designed, or the limit con­trols may not operate at all.

The duct system is a very important part of the installation. If the duct

system is improperly sized the furnace will not operate properly.

The ducts attached to the furnace plenum, should be of sufficient size
so that the furnace operates at the specified external static pressure
and within the air temperature rise specified on the nameplate.

IMPORTANT

The minimum plenum height is 12” (30.5 cm). The furnace will not
operate properly on a shorter plenum height. The minimum recom­mended rectangular duct height is 4” (10.1 cm) attached to the ple­num.

If a matching cased indoor coil is used, it may be placed directly on the
furnace outlet and sealed to prevent leakage. If an uncased indoor coil
with a thermoplastic drain pan is to be installed in the upflow/horizontal
configuration, then extra 2” minimum spacing may be needed to ensure
against drain pan distortion.

On all installations without a coil, a removable access panel is recom­mended in the outlet duct such that smoke or reflected light would be
observable inside the casing to indicate the presence of leaks in the
heat exchanger. This access cover shall be attached in such a manner
as to prevent leaks.

1083163-UIM-J-0918

!

WARNING

The duct system must be properly sized to obtain the correct airflow
for the furnace size that is being installed.

Refer to the furnace rating plate for the correct rise range and static
pressures or to Table 6 for the correct rise range.

If the ducts are undersized, the result will be high duct static pres­sures and/or high temperature rises which can result in a heat
exchanger OVERHEATING CONDITION. This condition can result in
premature heat exchanger failure, which can result in personal injury,
property damage, or death.

DUCT FLANGES

Four flanges are provided to attach ductwork to the furnace. These
flanges are rotated down for shipment. In order to use the flanges,
remove the screw holding an individual flange, rotate the flange so it is
in the upward position and reinstall the screw then repeat this for all 4
flanges.

If the flanges are not used, they must remain in the rotated down posi­tion as shipped.

For duct attachment,
if needed.

FIGURE 1: Duct Attachment

Factory
installed

DUCTWORK INSTALLATION AND SUPPLY PLENUM
CONNECTION - UPFLOW/HORIZONTAL

Attach the supply plenum to the furnace outlet. The use of
an approved flexible duct connector is recommended on all
installations. This connection should be sealed to prevent
air leakage. The sheet metal should be crosshatched to
eliminate any popping of the sheet metal when the indoor
fan is energized.

FLOOR BASE AND DUCTWORK INSTALLATION ­DOWNFLOW

Installations on combustible material or directly on any
floors must use a combustible floor base shown in Figure 8.
Follow the instructions supplied with the combustible floor
base accessory. This combustible floor base can be
replaced with a matching indoor coil, properly sealed to pre­vent leaks. Follow the instructions supplied with the indoor
coil cabinet for installing the cabinet to the duct connector.
Plug intake and vent pipe holes in bottom panel and move
grommet to desired vent side exit.

Downflow Air - Indoor Coil Cabinet

The furnace should be installed with coil cabinet part number specifi­cally intended for downflow application. If a matching indoor coil is
used, it may be placed directly on the furnace outlet and sealed to pre­vent leakage. For details of the coil cabinet dimensions and installation
requirements, refer to the installation instructions supplied with the coil
cabinet.

Attach the indoor coil cabinet to the duct connector, and then position
the furnace on top of the coil cabinet. The connection to the furnace,
indoor coil cabinet, duct connector, and supply air duct must be sealed
to prevent air leakage.

Johnson Controls Unitary Products 5

1083163-UIM-J-0918

COIL INSTALLATION

IMPORTANT

On all installations without a coil, a removable access panel is recom­mended in the outlet duct such that smoke or reflected light would be
observable inside the casing to indicate the presence of leaks in the
heat exchanger. This access cover shall be attached in such a man­ner as to prevent leaks.

'2:1)/2:

$33/,&$7,21

127(
9HULI\WKDWDOOGUDLQV
DUHWUDSSHGRUSOXJJHG

)851$&(

&2,/

&2,/

)851$&(

'5$,13/8*
)25+25,=217$/
6(&21'$5<'5$,1

83)/2:

$33/,&$7,21

The indoor coil must be mounted on the supply side of the furnace as
shown in Figure 2. Refer to the Installation Instructions provided with
each indoor coil.

)851$&(

/()7)/2:
$33/,&$7,21

&2,/

&2,/

5,*+7)/2:
$33/,&$7,21

'5$,13/8*
)259(57,&$/
6(&21'$5<'5$,1

)851$&(

35,0$5<'5$,1
75$3&211(&7,21

6(&21'$5<'5$,1
75$3&211(&7,21

FIGURE 2: Furnace and Coil Attachment

DOWNFLOW DUCT CONNECTORS

All downflow installations must use a suitable duct connector approved
by the furnace manufacturer for use with this furnace. The duct connec­tors are designed to be connected to the rectangular duct under the
floor and sealed. Refer to the instructions supplied with the duct con­nector for proper installation. Refer to the separate accessory parts list
at the end of these instructions for the approved accessory duct con­nectors.

FURNACE

WARM AIR PLENUM
WITH 1” FLANGES

FIBERGLASS
INSULATION

FIBERGLASS TAPE
UNDER FLANGE

COMBUSTIBLE FLOOR
BASE ACCESSORY

35,0$5<'5$,1
75$3&211(&7,21

$

RESIDENTIAL AND MODULAR HOME UPFLOW
RETURN PLENUM CONNECTION

Return air may enter the furnace through the side(s) or bottom depend­ing on the type of application. Return air may not be connected into the
rear panel of the unit.

SIDE RETURN APPLICATION

Side return applications pull return air through an opening cut in the
side of the furnace casing. This furnace is supplied with a bottom block­off panel that should be left in place if a side return is to be used. If the
furnace is to be installed on a flat, solid surface, this bottom panel will
provide an adequate seal to prevent air leakage through the unused
bottom opening. However, if the furnace is to be installed on a surface
that is uneven, or if it is to be installed on blocks or otherwise raised off
the floor, it will be necessary to seal the edges of the bottom panel

to the casing using tape or other appropriate gasket material to
prevent air leakage.

BOTTOM RETURN AND ATTIC INSTALLATIONS

Bottom return applications normally pull return air through a base plat­form or return air plenum. Be sure the return platform structure or return
air plenum is suitable to support the weight of the furnace.

The internal bottom panel must be removed for this application.

Attic installations must meet all minimum clearances to combustibles
and have floor support with required service accessibility.

FIGURE 3: Combustible Floor Base Accessory

6 Johnson Controls Unitary Products

1083163-UIM-J-0918

HORIZONTAL APPLICATION

FIGURE 4: Horizontal Application

IMPORTANT

This furnace may be installed in a horizontal position on either side as
shown above. It must not be installed on its back.

ATTIC INSTALLATION

Line contact only permissible
between lines formed by the
intersection of furnace top
and two sides and building
joists, studs or framing

Filter rack
must be a minimum
distance
of 18” (45.7 cm)
from the
furnace

Gas Piping

30” MIN.
Work Area

12”

12”

Supply
Air

Vent (Maintain
required
clearances to
combustibles)

Sheet metal in
front of furnace
combustion air
Openings is
Recommended

bend of the heat exchangers as lifting points as the tubes may shift out
of position or their location brackets/baffles.

SUSPENDED FURNACE / CRAWL SPACE
INSTALLATION

The furnace can be hung from floor joists or installed on suitable blocks
or pads. Blocks or pad installations shall provide adequate height to
ensure that the unit will not be subject to water damage.

Units may also be suspended from rafters or floor joists using rods, pipe
angle supports or straps. In all cases, the furnace should be supported
with rods, straps, or angle supports at three locations to properly sup­port the furnace. Place one support at the supply end of the furnace,
one support located approximately in the center of the furnace near the
blower shelf, and the third support should be at the return end of the fur­nace. Maintain a 6” (15.2 cm) minimum clearance between the front of
the furnace and the support rods or straps.

All six suspension points must be level to ensure proper and quiet fur­nace operation. When suspending the furnace, use a secure platform
constructed of plywood or other building materials secured to the floor
or ceiling joists. Refer to Figure 6 for details and additional information.

Support
Rod

Return
Air

FIGURE 5: Typical Attic Installation

This appliance is certified for line contact when the furnace is installed
in the horizontal left or right position. The line contact is only permissible
between lines that are formed by the intersection of the top and two
sides of the furnace and the building joists, studs or framing. This line
may be in contact with combustible material. Refer to Figure 5.

When a furnace is installed in an attic or other insulated space, keep
all insulating materials at least 12” (30.5 cm) away from furnace and
burner combustion air openings.

Sediment

Trap

!

WARNING

IMPORTANT

During installation, doors should remain on the furnace when
moving or lifting.

When moving or handling this furnace prior to installation, always leave
the doors on the furnace to provide support and to prevent damage or
warping of the cabinet. When lifting the furnace, support the ends of the
furnace rather than lifting by the cabinet flanges at the return air open­ings (bottom or sides) or supply air opening.

It is acceptable to use the primary heat exchanger tubes as a lifting
point provided that the tubes are lifted at the front of the heat exchang­ers where attached to the vestibule panel. Do not use the top return

Support
Angle (x3)

FIGURE 6: Typical Suspended Furnace / Crawl Space Installation

Maintain 6” minimum
clearance between support
rods and front of furnace

DOWNFLOW APPLICATION

To apply the furnace in a downflow position, it will be necessary to
rotate the vent blower 90° left or right so that the vent pipe passes
through the side of the furnace casing. See Figure 7.

Rotate vent
blower 90°
either way

LEFT SIDE VENT

FIGURE 7: Downflow Venting

RIGHT SIDE VENT

Johnson Controls Unitary Products 7

1083163-UIM-J-0918

&RPEXVWLRQ$LU,QOHW

&RQGHQVDWH'UDLQ
'RZQIORZ

´

%

´

´

/()76,'(

´9HQW
&RQQHFWLRQ
2XWOHW

´

´

´

&RPEXVWLRQ
$LU,QOHW

´

6833/<(1'

´

*DV3LSH
(QWU\

(OHFWULFDO
(QWU\

&RQGHQVDWH
'UDLQ

7KHUPRVWDW
:LULQJ

´9HQW
&RQQHFWLRQ
2XWOHW

&

)5217

$



*DV3LSH
(QWU\

(OHFWULFDO
(QWU\

&RQGHQVDWH
'UDLQ

7KHUPRVWDW
:LULQJ

5,*+76,'(

&RPEXVWLRQ$LU,QOHW

&RQGHQVDWH'UDLQ
'RZQIORZ

´9HQW
&RQQHFWLRQ
2XWOHW

´

2SWLRQDO5HWXUQ$LU
&XWRXW(LWKHUVLGH

´

´

5(7851(1'

FIGURE 8: Dimensions

Table 2: Cabinet and Duct Dimensions

BTUH (kW)

Input

Nominal

CFM (m3/min)

Cabinet

Size

A (in) A (cm) B (in) B (cm) C (in) C (cm) Lbs (kg)

Cabinet Dimensions (Illustrated in Figure 13)

40 (11.7) 1000 (28.3) A 14 1/2 36.8 13 3/8 34.0 11 3/4 29.8 113
60 (17.6) 1200 (34.0) B 17 1/2 44.4 16 3/8 41.6 13 1/4 33.7 122
80 (23.4) 1200 (34.0) B 17 1/2 44.4 16 3/8 41.6 14 3/4 37.5 126

80 (23.4) 1600 (45.3) C 21 53.3 19 7/8 50.5 16 1/2 41.9 136
100 (29.3) 1600 (45.3) C 21 53.3 19 7/8 50.5 18 1/4 46.4 142
100 (29.3) 2000 (56.6) C 21 53.3 19 7/8 50.5 18 1/4 46.4 145
120 (35.1) 2000 (56.6) D 24 1/2 62.2 23 3/8 59.4 21 3/4 55.2 156

´

´

%

$

Approximate

Operating Weights

SECTION III: FILTERS

FILTER INSTALLATION

!

CAUTION

All filters and mounting provision must be field supplied. All installa­tions must have a filter installed.

All applications require the use of a field installed filter. All filters and
mounting provision must be field supplied.

Filters must be installed external to the furnace cabinet. DO NOT

attempt to install filters inside the furnace.

NOTICE

Single side return above 1800 CFM is approved as long as the filter
velocity does not exceed filter manufacturer’s recommendation and a
transition is used to allow use on a 20x25 filter.

Table 3: Recommended Filter Sizes (High Velocity 600 FPM)

CFM (m³/min) Cabinet Size Side (in) Bottom (in)

1000 (28.3) A 16 x 25 14 x 25
1200 (34.0) B 16 x 25 16 x 25
1600 (45.3) C 16 x 25 20 x 25
2000 (56.6) C (2) 16 x 25 20 x 25
2000 (56.6) D (2) 16 x 25 22 x 25

1. Air velocity through throwaway type filters may not exceed 300 feet per min­ute (91.4 m/min). All velocities over this require the use of high velocity fil­ters.

2. Do not exceed 1800 CFM using a single side return and a 16x25 filter. For
CFM greater than 1800, you may use two side returns or one side and the
bottom or one side return with a transition to allow use of a 20x25 filter.

SIDE RETURN

Locate the “L” shaped corner locators. These indicate the size of the cut­out to be made in the furnace side panel. Refer to Figure 9.

Front of
Furnace

Side of
Furnace

Corner
Markings

FIGURE 9: Side Return Cutout Markings

Install the side filter rack following the instructions provided with that
accessory. If a filter(s) is provided at another location in the return air
system, the ductwork may be directly attached to the furnace side
panel.

IMPORTANT

Some accessories such as electronic air cleaners and pleated media
may require a larger side opening. Follow the instructions supplied
with that accessory for side opening requirements. Do not cut the
opening larger than the dimensions for the “Optional Return Air Cut­out” shown in Figure 8.

8 Johnson Controls Unitary Products

HORIZONTAL FILTERS

Any branch duct (rectangular or round duct) attached to the plenum
must attach to the vertical plenum before the filter. The use of straps
and/or supports is required to support the weight of the external filter
box.

DOWNFLOW FILTERS

Downflow furnaces typically are installed with the filters located above
the furnace, extending into the return air plenum or duct. Any branch
duct (rectangular or round duct) attached to the plenum must attach to
the vertical plenum above the filter height.

Filter(s) may be located in the duct system external to the furnace using
an external duct filter box attached to the furnace plenum or at the end
of the duct in a return filter grille(s). The use of straps and/or supports is
required to support the weight of the external filter box.

SECTION IV: GAS PIPING

GAS SAFETY

!

DANGER

An overpressure protection device, such as a pressure regulator,
must be installed in the gas piping system upstream of the furnace
and must act to limit the downstream pressure to the gas valve so it
does not exceed 0.5 psig (14" w.c., 3.48 kPa). Pressures exceeding

0.5 PSI (14” w.c., 3.48 kPa) at the gas valve will cause damage to the
gas valve, resulting in a fire or explosion or cause damage to the fur­nace or some of its components that will result in property damage
and loss of life.

1083163-UIM-J-0918

IMPORTANT

Plan the gas supply routing before determining the correct gas pipe
entry. Use 90° conventional elbow(s) and short pipe nipples to enter
through the cabinet access holes.

GAS PIPING INSTALLATION

Properly sized wrought iron, approved flexible or steel pipe must be
used when making gas connections to the unit. If local codes allow the
use of a flexible gas appliance connection, always use a new listed con­nector. Do not use a connector that has previously serviced another gas
appliance.

Some utility companies or local codes require pipe sizes larger than the
minimum sizes listed in these instructions and in the codes. The furnace
rating plate and the instructions in this section specify the type of gas
approved for this furnace - only use those approved gases. The instal­lation of a drip leg and ground union is required. Refer to Figure 11.

For left side supply gas pipe arrangement, two 1/2” elbows and two 1/2”
x 1-1/2” pipe nipples must be used. The arrangement shown in Figure
11 aligns entrance hole in furnace casing with supply gas pipe. Furnace
casing does not support installations completed using street-elbows.

´[´

*$6
9$/9 (

3,3(1,33/(



(/%2:

´[´
3,3(1,33/(

Outlet
Pressure
Port

Inlet

Wrench
Boss

Inlet
Pressure
Port

FIGURE 10: Gas Valve

To Gas
Supply

Ground
Union

Drip
Leg

Configuration

FIGURE 12: Gas Piping

OFF

ON

On/Off Switch
(Shown in ON position)

To Gas
Supply

External
Manual
Shut-off
Valve

Drip
Leg

Upflow

72*$6

Vent Port

Outlet

Main Regulator
Adjustment

NOTE: Ground Union maybe installed inside or outside unit.

External
Manual

Ground
Union

Gas
Valve

Gas
Pipe

Ground
Union

Gas
Pipe

To Gas
Supply

Drip
Leg

Shut-off
Valve

Downflow

6833/<

FIGURE 11: Left Side Supply Gas Pipe Arrangement

To Gas
Supply

Ground
Union

Gas
Valve

Drip
Leg

Configuration

Ground
Union

Gas
Pipe

Horizontal

Configuration

Drip
Leg

(/%2:



To Gas
Supply

Drip Leg

External Manual
Shut-off Valve

Gas
Valve

To Gas

Ground
Union

Supply

$

Johnson Controls Unitary Products 9

1083163-UIM-J-0918

GAS ORIFICE CONVERSION FOR PROPANE (LP)

IMPORTANT

An accessible manual shutoff valve must be installed upstream of the
furnace gas controls and within 6 feet (1.8 m) of the furnace.

The furnace must be isolated from the gas supply piping system by
closing its individual external manual shutoff valve during any pressure
testing of the gas supply piping system at pressures equal to or less
than 0.5 psig (3.5 kPa).

!

CAUTION

The gas valve body is a very thin casting that cannot take any exter­nal pressure. Never apply a pipe wrench to the body of the gas valve
when installing piping. A wrench must be placed on the octagon hub
located on the gas inlet side of the valve. Placing a wrench to the
body of the gas valve will damage the valve causing improper opera­tion and/or the valve to leak.

Gas piping may be connected from either side of the furnace using any
of the gas pipe entry knockouts on both sides of the furnace. Refer to
Figures 8 and 11.

Table 4: Nominal Manifold Pressure - High Fire

Gas Heating

Value

(BTU/cu ft.)

800 3.5 3.5 3.5 29.8 0.87 0.87 0.87

850 3.5 3.5 3.5 31.7 0.87 0.87 0.87

900 3.5 3.5 3.5 33.5 0.87 0.87 0.87

950 3.5 3.5 3.3 35.4 0.87 0.87 0.81

1000 3.5 3.2 2.9 37.3 0.87 0.80 0.73

1050 3.5 2.9 2.7 39.1 0.87 0.73 0.67

1100 3.2 2.7 2.4 41.0 0.80 0.66 0.61

2500 (LP) 9.8 8.2 7.5 93.2 (LP) 2.44 2.03 1.86

0-7999 8000-8999 9000-9999 0-2437 2438-2742 2743-3048

in. w.c. in. w.c. in. w.c. kPa kPa kPa

Manifold Pressures

Altitude (feet) Altitude (m)

This furnace is constructed at the factory for natural gas-fired operation,
but may be converted to operate on propane (LP) gas by using a fac­tory-supplied LP conversion kit. Follow the instructions supplied with
the LP kit.

HIGH ALTITUDE GAS ORIFICE CONVERSION

This furnace is constructed at the factory for natural gas-fired operation
at 0 – 7,999 feet (0 – 2,438 m) above sea level.

The manifold pressure must be changed in order to maintain proper
and safe operation when the furnace is installed in a location where the
altitude is greater than 7,999 feet (2,438 m) above sea level. Refer to
Table 4 for proper manifold pressure settings.

HIGH ALTITUDE PRESSURE SWITCH CONVERSION

For installation where the altitude is less than 5,000 feet (1,524m), it is
not required that the pressure switch be changed unless you are in an
area subject to low pressure inversions.

Manifold Pressures

Gas Heating

Value

(MJ/cu m)

!

DANGER

PROPANE AND HIGH ALTITUDE CONVERSION KITS

It is very important to choose the correct kit and/or gas orifices for the altitude and the type of gas for which the furnace is being installed.
Only use natural gas in furnaces designed for natural gas. Only use propane (LP) gas for furnaces that have been properly converted to use pro-

pane (LP) gas. Do not use this furnace with butane gas.
Incorrect gas orifices or a furnace that has been improperly converted will create an extremely dangerous condition resulting in premature heat

exchanger failure, excessive sooting, high levels of carbon monoxide, personal injury, property damage, a fire hazard and/or death.
High altitude and propane (LP) conversions are required in order for the appliance to satisfactory meet the application.
An authorized distributor or dealer must make all gas conversions.
In Canada, a certified conversion station or other qualified agency, using factory specified and/or approved parts, must perform the conversion.

The installer must take every precaution to insure that the furnace has been converted to the proper gas orifice size when the furnace is installed.
Do not attempt to drill out any orifices to obtain the proper orifice size. Drilling out a gas orifice will cause misalignment of the burner flames, caus­ing premature heat exchanger burnout, high levels of carbon monoxide, excessive sooting, a fire hazard, personal injury, property damage and/or
death.

SECTION V: ELECTRICAL POWER

!

ELECTRICAL POWER CONNECTIONS

Field wiring to the unit must be grounded. Electric wires that are field
installed shall conform to the temperature limitation for 63°F (35°C) rise
wire when installed in accordance with instructions. Refer to Table 5 in
these instructions for specific furnace electrical data.

Use copper conductors only.

CAUTION

10 Johnson Controls Unitary Products

1083163-UIM-J-0918

Table 5: Ratings & Physical / Electrical Data

Input Output

MBH kW MBH kW CFM

40 11.7 38 11.1 1000 28.3 95.5 30-60 17-33 190 88 1/2 6.8 11x8 15 10.6 1/2"

60 17.6 57 16.7 1200 34.0 95.5 30-60 17-33 190 88 1/2 6.8 11x8 15 10.6 1/2"

80 23.4 76 22.3 1200 34.0 95.5 40-70 22-39 190 88 1/2 6.8 11x8 15 10.6 1/2"

80 23.4 76 22.3 1600 45.3 95.5 35-65 19-36 190 88 1/2 6.8 11x10 15 10.6 1/2"

100 29.3 95 27.8 1600 45.3 95.5 40-70 22-39 190 88 1/2 6.8 11x10 15 10.6 1/2"

100 29.3 95 27.8 2000 56.6 95.5 35-65 19-36 190 88 3/4 8.4 11x11 15 12.2 1/2"

120 35.1 114 33.4 2000 56.6 95.5 45-75 25-42 190 88 3/4 8.4 11x11 15 12.2 1/2"

Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.
Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes.
The furnace shall be installed so that the electrical components are protected from water.

Nominal

Airflow

m3/min

AFUE

Air Temp.

Rise

% °F °C °F °C HP Amps

Max. Outlet

Air Temp

Blower

Blower

Size

Fuse or

Circuit

Breaker

Total Unit

Amps

Gas Pipe

Connection,

SUPPLY VOLTAGE CONNECTIONS

IMPORTANT

The power connection leads and wiring box may be relocated to the
opposite side of the furnace. Remove the screws and cut wire tie

Junction
Box

Connect ground
lead to screw

Electrical Entry

BLK

L1-Hot

WHT

Neutral

FIGURE 13: Electrical Wiring

1. Provide a power supply separate from all other circuits. Install over-

current protection and disconnect switch per local/national electrical
codes. The switch should be close to the unit for convenience in
servicing. With the disconnect or fused switch in the OFF position,
check all wiring against the unit wiring label. Refer to the wiring dia­gram in this instruction.

2. Remove the wiring box cover screws. Route all power wiring

through a conduit connector or other proper bushing that is field
installed into the unit opening and the junction box. In the junction
box there is a black wire, a white wire and a green ground screw.
Connect the power supply as shown on the unit’s wiring label
located on the inside of the blower compartment door, or the wiring
schematic in this section. Connect the black wire to L1 (hot) from
the power supply. Connect the white wire to neutral. Connect the
ground wire (installer-supplied) to the green (equipment ground)
screw. An alternate wiring method is to use a field-provided 2” (5.1
cm) x 4” (10.2 cm) box and cover on the outside of the furnace.
Route the furnace leads into the box using a protective bushing
where the wires pass through the furnace panel. After making the
wiring connections, replace the wiring box cover and screws. Refer
to Figure 12.

3. The furnace's control system requires correct polarity of the power

supply and a proper ground connection. Refer to Figure 12.

holding excess wiring. Reposition on the opposite side of the furnace
and fasten using holes provided.

LOW VOLTAGE CONTROL WIRING CONNECTIONS

Install the field-supplied thermostat by following the instructions that
come with the thermostat. With the thermostat set in the OFF position
and the main electrical source disconnected, connect the thermostat
wiring from the wiring connections on the thermostat to the terminal
board on the ignition module, as shown in Figures 13 & 14. Electronic
thermostats require the common wire to be connected. Apply strain
relief to thermostat wires passing through cabinet. If air conditioning
equipment is installed, use thermostat wiring to connect the Y and C
terminals on the furnace control board to the proper wires on the out­door unit.

IMPORTANT

Set the heat anticipator in the room thermostat to 0.4 amps. Setting it
lower will cause short cycles. Setting it higher will cause the room
temperature to exceed the set points.

IMPORTANT

Some electronic thermostats do not have adjustable heat anticipa­tors. They should be set to six cycles per hour. Follow the thermostat
manufacturer's instructions.

The 24-volt, 40 VA transformer is sized for the furnace components
only, and should not be connected to power auxiliary devices such as
humidifiers, air cleaners, etc. The transformer may provide power for an
air conditioning unit contactor.

NPT

Johnson Controls Unitary Products 11

1083163-UIM-J-0918

+&7KHUPRVWDW6LQJOH6WDJH)XUQDFH67'(&06LQJOH6WDJH$LU&RQGLWLRQHU

7+(50267$7

&

±9ROW&RPPRQ

5

±9ROW+RW

*

)DQ

<

)LUVW6WDJH

&RPSUHVVRU

:

)LUVW6WDJH+HDW

<

6HFRQG6WDJH

&RPSUHVVRU

:

6HFRQG6WDJH+HDW

RU2

5HYHUVLQJ9DOYH

6,1*/(67$*(

)XUQDFH

67'(&0

&

±9ROW&RPPRQ

5

±9ROW+RW

*

)DQ

<<

)XOO6WDJH&RPSUHVVRU

:

)XOO6WDJH+HDW

<

)LUVW6WDJH&RPSUHVVRU

([WHUQDO+XPLGLVWDW

2SWLRQDO2SHQRQ

+XPLGLW\5LVH

9$&+XPLGL¿HU

2SWLRQDO

FIGURE 14: Thermostat Chart - 1H/1C - Single Stage Furnace (STD-ECM) - Single Stage Air Conditioner

6,1*/(67$*(

$,5

&21',7,21(5

&

±9ROW&RPPRQ

5

±9ROW+RW

<

)LUVW6WDJH

&RPSUHVVRU

$

+&7KHUPRVWDW6LQJOH6WDJH)XUQDFH67'(&07ZR6WDJH$LU&RQGLWLRQHU

7+(50267$7

&

±9ROW&RPPRQ

5

±9ROW+RW

*

)DQ

<

)LUVW6WDJH

&RPSUHVVRU

:

)LUVW6WDJH+HDW

<

6HFRQG6WDJH

&RPSUHVVRU

:

6HFRQG6WDJH+HDW

RU2

5HYHUVLQJ9DOYH

([WHUQDO+XPLGLVWDW

2SWLRQDO2SHQRQ

+XPLGLW\5LVH

9$&+XPLGL¿HU

2SWLRQDO

FIGURE 15: Thermostat Chart - 1H/2C - Single Stage Furnace (STD-ECM) - Single Stage Air Conditioner

6,1*/(67$*(

)XUQDFH

67'(&0

&

±9ROW&RPPRQ

5

±9ROW+RW

*

)DQ

<

)LUVW6WDJH&RPSUHVVRU

:

)XOO6WDJH+HDW

<<

)XOO6WDJH&RPSUHVVRU

7:267$*(

$,5

&21',7,21(5

&

±9ROW&RPPRQ

5

±9ROW+RW

<

)LUVW6WDJH

&RPSUHVVRU

<

6HFRQG6WDJH

&RPSUHVVRU

$

12 Johnson Controls Unitary Products

ACCESSORY CONNECTIONS

The furnace control will allow power-switching control of various acces­sories.

ELECTRONIC AIR CLEANER CONNECTION

Two 1/4” (6.4 mm) spade terminals (EAC and NEUTRAL) for electronic
air cleaner connections are located on the control board. The terminals
provide 115 VAC (1.0 amp maximum) during circulating blower opera­tion.

HUMIDIFIER CONNECTION

Two 1/4” (6.4 mm) spade terminals (HUM and NEUTRAL) for humidifier
connections are located on the control board. The terminals provide 115
VAC (1.0 amp maximum) during heating system operation.

A mounting hole is provided on the control panel next to the furnace
control board for mounting a humidifier transformer if required.

TWINNING

These furnaces are not to be twinned. If more than one furnace is
needed in an application, each furnace must have its own complete
duct system and its own wall thermostat.

SECTION VI: CONDENSATE PIPING AND FURNACE VENTING CONFIGURATION

CONDENSATE DRAIN LOCATION

As shipped from the factory:

• For all 040, 060 & 080K input furnaces the main drain is plumbed
through the casing right-side opening when viewed from the front
of the furnace.

• For all 100 & 120 input furnaces the main drain is plumbed through
the casing left-side opening when viewed from the front of the fur­nace.

1083163-UIM-J-0918

IMPORTANT

Condensate must be disposed of properly. Follow local plumbing
or wastewater codes. The drain line must maintain a 1/4” per foot (20
mm/m) downward slope to the drain.

IMPORTANT

If an external vent tee is being installed, then it must have its own
condensate trap before it is disposed into an open or vented drain.

This is not to be considered as a second trap as referenced else­where in this document.

23(167$1'3,3(
$QWLVLSKRQDLUYHQW

´0D[

7((

NOTICE

The Figures 16 - 19 show the condensate drain arrangement for the
various possible furnace and vent blower positions.

The condensate hoses must slope downwards at all points.

!

CAUTION

The furnace condensate pan is self priming and contains an internal
trap to prevent flue gas leaking. Do not install an external condensate
trap.

When drain hose routing changes are required (shown in Figures 16-

19), be sure to cap all unused openings.

If rerouting hoses - excess length should be cut off so that no sagging
loops will collect and hold condensate - which will cause the furnace to
not operate.

No hose clamps are needed for connecting to the condensate pan.

IMPORTANT

The furnace, indoor coil, and humidifier drains may be combined and
drained together. The evaporator coil drain may have an external,
field-supplied trap prior to the furnace drain connection to prevent
conditioned air leakage. All drain connections (furnace, indoor coil, or
humidifier) must be terminated into an open or vented drain as close
to the respective equipment as possible. Regular maintenance is
required on condensate drainage system.

7223(125
9(17(''5$,1

$

FIGURE 16: Typical. Condensate drain, vertical installation

The condensate will flow to the drain better if an open stand pipe is
installed in the drain line. See Figure 15.

If indoor coil or humidifier drains are combined with the furnace drain,
then the open stand pipe could be raised higher, above the 5” minimum.

Do not drain other devices (humidifier, indoor coil, etc.) into the top
opening of the vent stand pipe. Instead, install a second tee in the
vented drain tube below the furnace drain tee and route additional
drainage through the new tee.

NOTICE

A loop has been added to the pressure switch vacuum hose. How­ever, ensure that all pressure switch hoses are routed such that they
prevent any condensate from entering the pressure switch.

Johnson Controls Unitary Products 13