Licensee
Winchester Model 9410 Lever Action Shotgun Owner’s Manual
Important instructions for
Winchester Model 9410 Lever Action .410 Shotgun
Customer Service Department (United States)
U. S. Repeating Arms Company, Inc.
275 Winchester Avenue
Morgan, Utah 84050-9333
Phone: 1-800-945-5237
Winchester trademarks licensed from Olin Corporation.
If you have any questions or comments regarding your new firearm, please feel free
to write or call us.
Model 9410 shotgun.
Model __________________________________________________________
Gauge __________________________________________________________
Serial Number ____________________________________________________
Purchased From __________________________________________________
Date of Purchase __________________________________________________
Use the space below to record information about your new
2
Licensee
Contents Page
Gun safety warnings . . . . . . . . . . . . . . . . . . . . . . . . .5
General description . . . . . . . . . . . . . . . . . . . . . . . . .7
Terminology and descriptions . . . . . . . . . . . . . . . . .7
Serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
General features . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Initial cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Oiling the action . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Operation of the hammer and hammer stop . . . . .13
Lowering the hammer . . . . . . . . . . . . . . . . . . . . . . .15
Trigger stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Assembly/Disassembly . . . . . . . . . . . . . . . . . . . . . .17
Installing a scope . . . . . . . . . . . . . . . . . . . . . . . . . . .17
General operation . . . . . . . . . . . . . . . . . . . . . . . . . .18
Loading procedures . . . . . . . . . . . . . . . . . . . . . . . .19
Unloading procedures . . . . . . . . . . . . . . . . . . . . . . .21
In the case of a misfire . . . . . . . . . . . . . . . . . . . . . .23
Firing procedures . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Sight adjustments . . . . . . . . . . . . . . . . . . . . . . . . . .25
Hammer extension . . . . . . . . . . . . . . . . . . . . . . . . .28
Magazine plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Cleaning and maintenance . . . . . . . . . . . . . . . . . . .32
Ordering parts / service / repair / questions . . . . . .34
Winchester.com and helpful links . . . . . . . . . . . . .35
3
THANK YOU
We sincerely hope that you are pleased with your new Winchester 9410 shotgun.
We at U.S. Repeating Arms Company thank you for the privilege of providing this
shotgun to you. We are especially proud of the many years of enjoyment it is
certain to provide for you and your family. The 9410 is another shotgun in an over
130 year-old tradition of producing quality firearms for the World’s sportsmen.
Quality of manufacture, design, craftsmanship and function are of utmost concern
to us. We believe you’ll find that your new 9410 meets the Winchester tradition of
quality in every way. If you have any questions or comments regarding your new
firearm, please feel free write to us at our administrative offices:
Customer Service Department
U. S. Repeating Arms Company, Inc.
275 Winchester Avenue
Morgan, Utah 84050-9333
Phone: 1-800-945-5237
4
GUN SAFETY WARNINGS
IT IS ESSENTIAL THAT THESE OPERATING
INSTRUCTIONS BE THOROUGHLY STUDIED
BEFORE USING THIS FIREARM TO ASSURE
PROPER AND SAFE GUN HANDLING. FAILURE
TO FOLLOW THESE INSTRUCTIONS OR FAILURE
TO OBEY ANY SAFETY WARNING MAY RESULT
IN INJURY TO YOURSELF OR OTHERS, OR
CAUSE DAMAGE TO YOUR GUN.
As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can
be the difference between life and death. There is no
excuse for careless or abusive handling of any firearm.
At all times handle your shotgun and any other firearm
with intense respect for its power and potential danger.
PLEASE READ AND UNDERSTAND ALL OF THE
CAUTIONS, PROPER HANDLING PROCEDURES
AND INSTRUCTIONS OUTLINED IN THIS BOOKLET
BEFORE USING YOUR NEW FIREARM.
1. Do not carry a loaded gun while walking, running,
climbing a tree, crossing a fence or anywhere you might
slip or fall, drop the gun or otherwise bump or jar the gun.
A gun that is dropped, bumped, or jarred with a chambered
round might accidentally discharge even with the safety on,
causing serious injury to you or someone else. When a
round is chambered keep the safety on until you are ready
to shoot.
2. Do not rely on the safety to prevent accidental discharge.
Many safeties merely block the trigger and prevent firing
by pulling the trigger. The safety may not prevent an
accidental discharge due to dropping, jarring, or bumping
a gun.
3. Use only ammunition for which the gun is chambered
as indicated on the barrel, to prevent excessive pressure
and possible serious personal injury.
4. Incorrectly reloaded ammunition can cause serious
personal injury and damage to the firearm due to excessive
pressure. Reload only after proper instruction and in strict
compliance with instruction and data contained in
current reloading manuals.
5. Never point a gun at anything you do not intend to shoot.
Always keep it pointed in a safe direction in case of
accidental discharge.
6. Always check to ensure that the barrel is free of
obstructions before loading and using the gun. If you
experience light recoil or off sound, check the barrel
for obstruction.
7. Before firing, clean any grease or oil out of barrel with
cleaning rod and patch. Grease or heavy accumulation of
oil can cause excessive pressure and result in serious
personal injury.
5
8. Keep barrel, chamber and action free of rust. Rust in
the barrel and chamber can cause excessive pressures
resulting in serious injury. A rusted, pitted or eroded
barrel should be replaced.
9. Use hearing protection to prevent ear damage from
repeated exposure to gunfire.
10. Always use proper shooting glasses to prevent eye
injury from flying particles.
11. Never carry a loaded gun in a motor vehicle or carry
one into a dwelling. Always carefully unload the gun
before entering a motor vehicle, a dwelling or an area
such as a camp. Always point a gun in a safe direction
while loading or unloading to prevent serious injury in
case of an accidental discharge. Never load in the house
or in your vehicle.
12. Never shoot at a hard, flat surface or at the surface of
water to avoid a ricochet and possible serious personal
injury to yourself or a bystander.
13. Store guns in a clean dry place out of reach of children
and separated from stored ammunition.
14. Never alter any parts of your gun. Any alterations or
adjustments that may become necessary to the operating
mechanism should be performed by a qualified gunsmith.
15. Hunting from elevated surfaces such as tree stands is
dangerous. Doing so may increase the risk of handling any
firearm. Always make certain that the stand being used is
safe, sturdy and stable. Always make certain your firearm
is unloaded when it is being taken up and down from the
stand. Always make certain that your firearm is not
dropped from the stand or dropped while it is being taken
up or down from the stand.
16. Discharging firearms in poorly ventilated areas, cleaning
firearms, or handling ammunition may result in exposure to
lead and other substances known to cause birth defects,
reproductive harm and other serious physical injury. Have
adequate ventilation at all times. Wash hands thoroughly
after exposure.
6
GENERAL DESCRIPTION
Congratulations on your purchase of a Winchester
Model 9410 shotgun — certainly one of the most unique
and fun-to-shoot guns ever. The original Winchester
Model 94 design is famous for fast handling and natural
pointability. No wonder it lends itself so well to a
chambering in .410 bore with a smoothbore, unrifled
barrel. Whether you are after squirrels, rabbits, upland
birds, rodents or even bigger varmints or game (using
slugs) the Model 9410 will prove to be as effective as it is
enjoyable. The Model 9410 can also be an inventive way
to boost the fun of clay target shooting.
This manual covers all current versions of the Model 9410
(the first Winchester Model 94 chambered for .410 shotgun shells). You get all the great features that have made
the Model 94 design famous for over a century. Plus other
advantages like:
• Advanced rebounding hammer, hammer block and
cross bolt hammer stop.
• Positive angle ejection (ejection out the side, to the
right, for better ejection when using a scope).
• A special extractor/ejector design offers positive,
controlled ejection with shotshells.
As you examine your new Model 9410 you will observe
that it possesses the genius of the original Model 94 design
— the most famous of all lever action rifles. No gun better
represents the Winchester legacy than the Model 94 rifle.
Just like the original Model 94 rifles of the past, you’ll
appreciate the beautiful craftsmanship and superb function
of the your Model 9410.
With a few minor exceptions, the action is identical to
the way the original rifles were made in 1894. Yet you’ll
find that today’s manufacturing equipment and technology
make it possible to produce this variation with more
precision, closer metal-to-wood fits and tighter overall
tolerances than possible in earlier times. We’re sure that
the greatest Winchester gunmakers of the past would be
very proud of today’s Model 9410 shotgun.
Your new Model 9410 features our highly functional manual
hammer stop built into the receiver, as well as our
rebounding hammer system. This shotgun also contains an
automatic hammer stop which blocks the hammer from
striking the firing pin until the trigger is pulled. These
advanced features move this traditional design to a new
level of convenience and safety. All features are explained
in detail later in this manual.
TERMINOLOGY AND DESCRIPTIONS
Descriptions in this manual generally refer to the gun in
the horizontal position. That is, in the normal firing
position. For example, the muzzle is forward or front; the
7
Rebounding hammer
Manual hammer stop
Ejection Port
Rear Sight
Barrel bands
FIGURE 1A
Front Sight
Trigger
Guard
Trigger
Finger lever
Buttstock
Butt Plate
buttstock is rearward or rear; the trigger is downward or
underneath; the sight is upward or on top. For general
parts terminology, refer to Figure 1-A.
The Winchester Model 9410 is also shown in some detail,
focussing on the hammer and lever mechanisms
(Figure 1-B through 1-C). You must be familiar with these
part names in order to follow instructions contained in
this book. Figure 1-D covers the general features and
benefits of the Model 9410 design. (Model 9410
Traditional shown above, other models will differ slightly.)
Throughout this manual the “action” refers to the
mechanism of this shotgun which loads and secures the
shell in the chamber.
Loading Port
Forearm
Magazine Tube
IMPORTANT: REFER TO FIGURE 1-A FOR
GENERAL PART DESCRIPTIONS REGARDING
YOUR NEW SHOTGUN. YOU MUST BECOME
FAMILIAR WITH ALL PART NAMES LISTED
BEFORE PROCEEDING WITH THE REST OF
THE INSTRUCTIONS IN THIS MANUAL.
SERIAL NUMBER
The serial number is located on the bottom of the receiver,
at the front, close to where it contacts the rear of the
forearm. Record the serial number in this booklet for
future reference.
8
Muzzle
Manual
hammer
stop
FIGURE 1B FIGURE 1C
Manual hammer stop
Rebounding
hammer
Pushed to
left: off safe
Pushed to
right:
“on safe”
Rebounding
hammer
AMMUNITION
Your Winchester Model 9410 is designed to shoot modern
factory shotgun shells only. It is chambered in .410 bore
1
with a 2
⁄2" chamber length.
The gauge of your new Model 9410 is inscribed on the
barrel near the receiver. Use only ammunition for which
your Model 9410 is chambered — as indicated on the
barrel — to prevent excessive pressure and possible serious
injury. Please observe these important specifications and
Trigger stop
Finger Lever
Trigger
Trigger Guard
restrictions regarding your new Model 9410 shotgun.
• Factory .410 bore shotgun shells only.
1
• Chambered for 2
⁄2" shells only.
• Never attempt to load 3" shells.
• Barrel has a smooth bore with no rifling.
• Shoots full choke patterns with bird shot.
• Designed to shoot all factory
1
⁄2" field and target loads.
2
1
⁄2" Foster-type (rifled) slugs.
2
1
⁄2" buckshot loads.
2
(Continued on page 12)
9
MODEL 9410 FEATURES
Model 9410 Traditional shown, other
models differ slightly.
The stock is profiled for
fast handling and classic
good looks.
Today’s Model 9410 benefits from improvements in the entire line of firearms based on the Model 94 design. You’ll
see it in its overall fit and finish, the level of precision and the quality of the materials. The 9410 offers all the handling advantages of the original Model 94 design in a shotgun that is ideal for clay target practice, general training
and a variety of hunting situations.
All models are drilled and tapped for scope mounts. With a scope
and the proper rifled slug your Model 9410 can be effective for
larger varmints — with better results at extended ranges.
The manual hammer stop with
rebounding hammer gives you an
extra margin of safety.
Metal-to-metal fits show a high level
of precision which you can feel in the
smooth function of the action.
10
The ultra-strong breech block design has
stood the test of time and is a main reason
for the new Model 9410’s slug shooting
accuracy.
FIGURE 1D
The handling characteristics of the Model 9410 make it ideal for hunting small
game in heavy brush or for use on varmints where there may be very little time to
get off a shot at fast moving pests.
Every Model 9410 comes with open sights. Most
will feature a traditional drift-windage and elevation
adjustable rear sight and ramp style front sight.
Some feature fiber optic front sights.
The Model 9410 features a specially designed ejector/extractor
system that does not eject the shell until the lever is worked fully
forward. This gives more reliable ejection with the numerous factory
.410 bore shells on the market. The angle ejection receiver
configuration found on the 9410 lets you utilize a scope as well —
sending empties to the right, under the scope.
The Model 9410 has a level of responsiveness, fast handling, follow-up
shot quickness and total reliability that makes it one of today’s
most enjoyable small gauge shotguns.
11
The Model 9410 is chambered in
.410 bore. This is a versatile
“gauge” that offers the versatility
of numerous loadings: birdshot
field loads, Foster-type slugs and
clay target loads.
The cold-forged chrome
molybdenum steel barrel
is of the same material
employed on our
famous Model 94
and Model 70 rifles.
• Magazine capacity: The Model 9410 Traditional will
hold Nine (9) shells maximum with most brands/styles of
factory loads (may be one less with some brands/styles).
Total capacity can be ten (10) if the chamber is loaded
first, before loading the magazine.
The Model 9410 Packer will hold Five (5) shells maximum with most brands/styles of factory loads. Total
capacity can be six (6) if the chamber is loaded first,
before loading the magazine.
Winchester ammunition is always an excellent choice for
your new Winchester Model 9410 shotgun, delivering the
unmatched performance and dependability you want.
MAKE SURE YOU USE ONLY THE EXACT
AMMUNITION/GAUGE AS LISTED ON THE
LEFT SIDE OF THE BARREL. IMPORTANT:
USE ONLY AMMUNITION SUITABLE FOR
USE IN A .410 BORE SHOTGUN WITH A
TUBULAR MAGAZINE.
Use only star crimped or roll crimped shells. Because the
Model 9410 uses a tubular magazine, never use shells with
protruding, pointed or conical point slugs. Never use a
shell which has a slug protruding beyond the crimp.
Failure to follow these instructions may result in injury to
yourself or others, or cause damage to your gun.
NEVER LOAD OR SHOOT ANY CENTERFIRE
RIFLE AMMUNITION IN YOUR MODEL 9410
SHOTGUN. SERIOUS INJURY TO YOURSELF
AND OTHERS MAY RESULT. U.S. REPEATING
ARMS COMPANY, INC., CAN ASSUME NO
RESPONSIBILITY FOR INCIDENTS WHICH
OCCUR THROUGH THE USE OF SHOTGUN
SHELLS OF NONSTANDARD DIMENSION OR
THOSE THAT WHEN SHOT, DEVELOP
PRESSURES IN EXCESS OF INDUSTRY
STANDARDS ESTABLISHED BY THE SPORTING
ARMS AND AMMUNITION MANUFACTURERS’
INSTITUTE (SAAMI).
DISCHARGING FIREARMS IN POORLY
VENTILATED AREAS, CLEANING FIREARMS,
OR HANDLING AMMUNITION MAY RESULT IN
EXPOSURE TO LEAD AND OTHER SUBSTANCES
KNOWN TO CAUSE BIRTH DEFECTS,
REPRODUCTIVE HARM AND OTHER SERIOUS
PHYSICAL INJURY. HAVE ADEQUATE
VENTILATION AT ALL TIMES. WASH HANDS
THOROUGHLY AFTER EXPOSURE.
Incorrectly reloaded ammunition can cause serious
personal injury and damage to the firearm due to excessive
pressure. Reload only after proper instruction and in strict
compliance with instructions and data contained in
current reloading manuals.
12
Lightly oil the action
at these points
FIGURE 2
INITIAL CLEANING
Some metal parts of your new Model 9410 have been
coated at the factory with a rust preventative compound.
Before using your Model 9410, clean the anti-rust compound from the inside of the barrel, receiver, shell feed
mechanism and the action/chamber areas. A high quality,
light gun oil should be used to remove this compound and
to give your new gun its first lubrication. Clean the barrel
using a cleaning rod and patch as explained under
“Cleaning and Maintenance Suggestions” found later in
this manual. First lubrication suggestions are outlined below.
If your new Model 9410 is for collector’s purposes only, it
is permissible to leave the rust preventative compound in
place and keep your Model 9410 in its box for maximum
protection during long term storage.
OILING THE ACTION
Before the first firing of your Model 9410 you should first
wipe the mechanism completely clean, clean the bore and
apply a few drops of quality oil on the following surfaces
(Figure 2):
• Along the breech bolt surface.
• On each side of the vertical locking lug on the top
and bottom.
• Along the breech bolt rail surfaces.
Avoid applying too much oil. Only a light film is necessary.
Cleaning and Maintenance Suggestions should be followed
before each oiling.
OPERATION OF THE HAMMER
The Model 9410’s Rebounding Hammer is a safety feature
designed to protect the firing pin from being struck by the
hammer when the trigger is not being pulled. After firing
your shotgun the hammer immediately moves to the
rebound position. From this position, under normal
conditions, the hammer is prevented from moving forward
and striking the firing pin. The rebound position and the
manual hammer stop are intended to work together to
provide protection against unintentional or accidental firing.
13
Rebound position
of hammer
Cocked position of
hammer.
HAMMER POSITIONS —
FIGURE 3
FIGURE 4
The rebounding hammer on your Model 9410 has two
positions as follows:
1. Rebound or “safety” position. This position
(Figure 3) takes the place of the dropped and half-cocked
positions found on earlier, original Model 94 rifle models.
The rebounding feature of the hammer essentially eliminates the dropped position. The hammer only travels to
the dropped position momentarily after the trigger has
been pulled with the hammer cocked. The hammer then
automatically moves to the rebound position.
THE REBOUND POSITION IS CONSIDERED
THE "SAFETY" POSITION. IT IS THE RECOMMENDED POSITION OF THE HAMMER AT ALL
TIMES AND SHOULD BE IN THAT POSITION
EXCEPT (1) WHEN FIRING IS IMMINENT (2) OR
IMMEDIATELY AFTER THE ACTION HAS
BEEN CYCLED.
2. Cocked position. This is the position that the hammer
is moved to when firing is imminent (Figure 4). It is also
the position the hammer moves to when the action is
cycled using the finger lever.
WHEN THE HAMMER IS IN THE COCKED
POSITION THE HAMMER STOP SHOULD BE IN
THE "ON" POSITION UNLESS FIRING IS IMMINENT.
MANUAL HAMMER STOP —
The manual hammer stop is a modern feature built into the
action of your Model 9410 to provide an additional level of
safety when it is in the "on" position.
“On” Position. When the hammer stop is pushed all the
way to the right it is in the on position (Figure 5-A). In this
position it blocks the hammer from striking the firing pin.
14
FIGURE 5A FIGURE 5B
Hammer stop in “on”
(safe) position
THIS IS THE RECOMMENDED POSITION OF
THE HAMMER FOR ALL TIMES EXCEPT WHEN
FIRING IS IMMINENT.
“Off” Position. When the hammer stop is pushed all the
way to the left it is in the “off” position (Figure 5-B).
This is the position of the hammer stop when firing is
imminent.
To place the hammer stop in the “on” position:
1. First, POINT YOUR SHOTGUN IN A SAFE
DIRECTION, THEN PLACE THE MANUAL
HAMMER STOP IN THE “ON” POSITION
by pushing it from left to right with your thumb or finger
(the thumb works well for right handed shooters) until
the red “warning” ring disappears (Figure 5-A).
2. When the red ring is visible on the left side of the manual
hammer stop, it is in the “off” position (Figure 5-B). It is
placed in the “off” position by pushing the stop with your
Hammer stop
in off (fire)
position
finger fully to the left until the red ring is showing. The
manual hammer stop can be actuated with the hammer in
the rebound or cocked position.
LOWERING THE HAMMER
At any time the hammer can be cocked either manually
or by cycling the finger lever fully. Unless shooting is
imminent it is important to move the hammer immediately
to the rebound position from the cocked position.
To do this:
1. Make sure the barrel is pointed in a safe direction and
that the hammer stop is in the “on” position.
2. Get a stable grip on your shotgun with your hand in
shooting position. With slight upward pressure from your
fingers push the finger lever upward against the stock (this
releases the trigger stop as explained later). Place your
15
Firmly hold the
hammer back
FIGURE 6A FIGURE 6B
Remove your finger
from the trigger and
lower the hammer to
the rebound position
Be extremely careful!
thumb on the hammer and firmly hold the hammer back
slightly with your thumb (Figure 6-A).
3. While holding the hammer back apply just enough
pressure on the trigger and finger lever to release the hammer
from the full-cock position. Immediately remove your finger
from the trigger and slowly and carefully allow the hammer
to lower into the rebound position (Figure 6-B).
TRIGGER STOP
It is important that the breech be fully closed before your
shotgun is fired. To help assure that this is always the case,
your Model 9410 has a trigger stop mechanism. To fire
your shotgun it is necessary for the finger lever to depress
the trigger stop (Figure 7). The trigger stop is not a safety.
It is simply an interlock to assure that the breech is fully
closed before a shell can be discharged. Never rely on the
trigger stop to prevent accidental discharge.
When wearing gloves, a portion of the glove may get
between the lever and the lower tang preventing the lever
from depressing the trigger stop — making it necessary to
squeeze upward on the finger lever.
REMEMBER, NEVER RELY TOTALLY ON YOUR
FIREARM’S MECHANICAL “SAFETY” DEVICES.
As is true with other firearms, when the safety mechanism
on this shotgun is engaged, it is designed to prevent accidental
discharge. However, this mechanism will not necessarily
prevent the accidental discharge of this firearm as a result
of jarring or abuse such as occurs when a firearm is dropped.
ALWAYS ASSUME THAT YOUR GUN CAN BE
FIRED AT ANY TIME, EVEN WITH ALL SAFETY
MECHANISMS ENGAGED.
16
FIGURE 7
Trigger Stop
Finger Lever
Whenever you are not actually firing your shotgun always
be certain that your gun is pointed in a safe direction.
Continually be aware of the position of the manual hammer
stop on your shotgun. Check it both manually and visually
to avoid any chance of accidental discharge. Always keep
the manual hammer stop in the “on” position unless you
are actually firing the shotgun. It is a good idea to keep
the action open (with the finger lever down) at all times
other than when you are in the field and shooting is
imminent.
IMPORTANT: IT IS ALWAYS RECOMMENDED
THAT THE ACTION BE KEPT OPEN AT ALL
TIMES WHEN YOUR SHOTGUN IS LAYING ON
ANY BENCH OR TABLE AT A SHOOTING
RANGE OR OTHER FACILITY. ALWAYS KEEP
THE MUZZLE OF YOUR SHOTGUN POINTED IN A
SAFE DIRECTION. FAILURE TO FOLLOW THE
ABOVE INSTRUCTIONS COULD RESULT IN
INJURY OR DEATH TO YOURSELF OR OTHERS.
ASSEMBLY / DISASSEMBLY
Your Model 9410 comes fully assembled in the box. No
assembly to the gun itself is required. No disassembly is
required for normal maintenance.
If your Model 9410 requires disassembly for any reason
(such as requiring extra cleaning after being dropped in
water) it should be performed by a competent gunsmith,
by one of our Authorized Repair Centers, or by our
service facility.
INSTALLING A SCOPE
Rifled slugs (Foster-type) in .410 bore can offer excellent
accuracy when used in your new shotgun. Consequently,
in some situations you may want the advantage of a scope
or dot type sight. Scope mounts are available separately.
General instructions for installing scope mounts are
outlined below. Most systems will be similar to the ones
explained here. Be sure to also follow the instructions
provided with your mounts.
1. Remove the plug screws and de-grease the holes in the
top of the receiver.
17
2. Each mount comes in two pieces. Remove the mount
caps (top parts) and fasten the mounts (bottom parts) to
the top of the receiver. (You may want to apply a removable
locking compound to each screw to assure they stay
secure under the effect of recoil). The mount with two
holes parallel to the receiver is mounted on the front of
the receiver. The mount with holes side by side (perpendicular to the receiver) mounts at the back.
3. Once the mounts are in place, lay the scope inside the
stirrups, replace the caps and lightly tighten the cap screws.
4. Before fully tightening the cap screws adjust the scope
forward or backward to achieve the proper eye relief (eye
relief is the distance your eye must be from the rear lens of
the scope to bring the entire field of view into focus).
Proper eye relief is extremely important even with .410
shells. To prevent injury resulting from the rim of a scope
hitting your forehead, follow all instructions concerning
eye relief provided with your scope.
5. When the proper eye relief is found, tighten the cap
screws in a rotating, crossing pattern. Do not over tighten
so as to strip the screws or damage the scope tube.
6. Now carefully follow the instructions on sighting in
provided with your scope.
Important: If you are using a scope, you may consider
using a hammer extension. Refer to the instructions on
mounting a hammer extension later in this manual.
GENERAL OPERATION
ALWAYS KEEP THE MUZZLE POINTED IN A
SAFE DIRECTION.
Prior to using live ammunition, it is essential that you
familiarize yourself thoroughly with these operating
instructions. Get accustomed to the feel of your new gun.
• Know the forces required to operate the action
• Know what forces are required to pull the trigger
• ABOVE ALL, KNOW HOW TO PLACE THE
HAMMER INTO THE SAFETY (REBOUND)
POSITION AND THE MANUAL HAMMER
STOP INTO THE “ON” POSITION.
Throughout this manual the “action” refers to the mechanism
of a firearm which loads and secures the shell in the
chamber. If the action resists closing, do not force it.
Small pieces of grit or other obstructions can make it
difficult to close the action. Make sure all surfaces are
clean if any unusual resistance is felt. However, remember
that this is a finely fitted action purposely made with tight
fitting tolerances. This assures your gun of good part-topart fit for many years to come and is the sign of a finely
crafted firearm.
18
LOADING PROCEDURES
USE THE CORRECT AMMUNITION AS INDICATED
BY THE INSCRIPTION ON THE BARREL. AS
EXPLAINED PREVIOUSLY, BEFORE LOADING
YOUR SHOTGUN MAKE SURE ALL GREASE
AND OIL HAS BEEN REMOVED FROM THE
BARREL AND CHAMBER, AND THERE ARE
NO OBSTRUCTIONS IN THE BARREL OR
ACTION AREAS.
LOADING THE CHAMBER —
The chamber may be loaded two ways:
(1) Load the chamber by placing a shell directly into the
chamber through the opened action (Figure 8), or
(2) load the chamber by transferring a shell that was
previously loaded into the magazine (Figure 9) to the
chamber by operating the finger lever.
When loading the chamber directly, the magazine should
be empty. You must be careful to insert the end of the
shell partially into the chamber before operating the finger
lever to close the action. If a shell does not chamber
completely when you close the action you should eject it
and inspect it. The problem may be caused by the crimp
and you can simply try again to chamber it. Be sure to
check the shell to make sure it is a 2
1
⁄2" shell and not a 3"
FIGURE 8
Loading directly into the
chamber
shell. If it is a 3" shell do not use it or try to chamber it in
your Model 9410. Store it away separately from your gun.
IN EITHER CASE, ALWAYS FIRST PLACE THE
MANUAL HAMMER STOP IN THE “ON” POSITION,
AND THEN PLACE THE HAMMER INTO THE
SAFETY (REBOUND), POSITION UPON CLOSING
THE ACTION.
LOADING THE MAGAZINE —
The magazine is loaded through the port on the right side
of the receiver.
1. With the action closed and the manual hammer stop in
the “on” position and the hammer in the safety (rebound)
19
FIGURE 9
Working the
finger lever
Loading a
shell from
the magazine
Insert the shell
through the loading port
FIGURE 10
position, press the spring cover inward with the crimp
end of the first shell until the entire shell has entered the
loading port (Figure 10).
2. Then, insert the next shell in the same manner, pushing
down on the cover fully with the shell, then pushing the
preceding shell into the magazine.
3. Repeat this procedure with each shell, pushing the last
shell past the end of the spring cover, allowing the cover to
snap closed (Figure 11). Do not exceed the
recommended capacity of the magazine. With practice, the
shell can be inserted until only the rim is exposed and the
spring cover is depressed to aid in loading the next shell.
If a shell is loaded manually into the chamber before you
begin loading shells into the magazine, you will increase
total shell capacity by one; in the case of the Model 9410
Traditional model, nine in the magazine and one in the
chamber. If you open the action to load directly into the
chamber with the magazine already loaded it may be difficult
or impossible to close the action. You may need to
remove the shell from the chamber manually to allow the
shell on the carrier to move into position for chambering.
BEFORE LOADING, ALWAYS MAKE SURE TO
PLACE THE MANUAL HAMMER STOP IN THE
“ON” POSITION, AND THE HAMMER INTO
THE SAFETY (REBOUND), POSITION.
CAUTION: ALWAYS MAKE SURE THE SHELLS
ARE OF THE PROPER GAUGE AND LENGTH
FOR YOUR MODEL 9410 SHOTGUN. CHECK
20
Cover closed
FIGURE 11
Push the last shell fully in,
allowing the cover to close
THE AMMUNITION DESIGNATION ON THE
BARREL. FAILURE TO FOLLOW THIS
INSTRUCTION CAN RESULT IN SEVERE DAMAGE
TO YOUR GUN AND POSSIBLE SERIOUS
INJURY TO YOURSELF OR OTHERS.
UNLOADING PROCEDURES
Fully unloading your shotgun for storage or in other
appropriate situations is essential to safe gun handling.
BEFORE UNLOADING, CHECK TO ASSURE
THAT THE MANUAL HAMMER STOP IS IN
THE “ON” POSITION (SAFE) BY PUSHING IT
FROM LEFT TO RIGHT. KEEP YOUR FINGER
AWAY FROM THE TRIGGER WHEN CYCLING
THE ACTION.
1. With the gun pointed in a safe direction and your finger
off the trigger, swing the finger lever downward fully. This
will extract any shell from the chamber and eject it.
Capture (or pick up) the shell and return the finger lever
fully upward.
2. Proceed to operate the finger lever in the same manner
transferring all the remaining cartridges from the magazine
to the chamber and then eject them out.
THROUGHOUT THE UNLOADING PROCESS
MAKE SURE THAT THE MANUAL HAMMER
STOP STAYS IN THE "ON" POSITION AND
THAT YOU KEEP YOUR FINGER AWAY FROM
THE TRIGGER AT ALL TIMES.
When shells no longer eject when you cycle the action,
further assure that no shells remain by opening the action
and visually checking the chamber and feed/magazine
mechanism to be sure no shells remain (Figure 12).
IMPORTANT: ALWAYS VISUALLY NOTE,
BY LOOKING THROUGH THE TOP OF THE
OPEN RECEIVER, THAT THE MAGAZINE
FOLLOWER IS SHOWING—AND NOT A SHELL
BASE. ALWAYS DOUBLE CHECK THAT NO
SHELLS REMAIN.
21
Carefully inspect the
chamber and feed/magazine
mechanisms for any shells
FIGURE 12
Check the
magazine follower
After the last live round is moved out of the magazine
and ejected, immediately lower the hammer to the safe
(rebound) position as explained previously.
REMOVING A 3" SHELL FROM THE MAGAZINE —
The Model 9410 is designed for
21⁄2"
shells only. If you
inadvertently load a 3" shell into the magazine it takes a
special procedure to clear it. You will probably first notice
that you have inadvertently loaded a 3" shell in the magazine
when you lower the finger lever to move a new shell to the
chamber and the shell does not move up on the carrier. A
close inspection will reveal that the crimp end of the shell
cannot clear the magazine tube. To remove the shell from
the action follow these steps:
1. Close the action, returning the shell back into the magazine
tube. You may have to work the lever a bit to move the
crimp end of the shell past the cartridge stop if it hangs up
slightly. Pushing down on the crimp end of the shell with
your finger while closing the action with your other hand
may also release it and allow the shell to return back into
the magazine tube. Be careful not to pinch your finger.
2. With the action closed use a finger of your free hand to
push fully in on the spring cover of the loading port and
hold it there (Figure 13).
3. While holding the cover in, open the action by pulling
down and continuing forward on the finger lever until the
action is open. CONTINUE TO HOLD THE SPRING
COVER IN with your finger.
4. Remove your other hand from the finger lever and use
your finger or the end of a small screwdriver to push (gently
pry) the rim of the shell to the right until it rides up on the
spring cover slightly (Figure 14).
5. Use your finger or a small screwdriver to gently encourage
the shell rearward, out of the loading port until you can
grasp it with your fingers and pull it free.
This is not a procedure you want to do often — so please be
very careful not to mix
The Model 9410 is designed solely for
21⁄2"
and 3" shells in your pockets.
21⁄2"
shells.
22
FIGURE 13 FIGURE 14
Use your finger to push the
cover in and hold it there.
IN THE CASE OF A MISFIRE
Only rarely will modern factory ammunition experience a
misfire. If this ever happens to you when shooting your
Model 9410 please follow these instructions carefully.
CAUTION: IN CASE OF MISFIRE, KEEP THE
BARREL POINTED IN A SAFE DIRECTION,
PLACE THE MANUAL HAMMER STOP IN THE
“ON” POSITION AND CAREFULLY OPEN
ACTION WHILE AVOIDING DIRECT EXPOSURE
TO THE BREECH BY YOURSELF AND OTHERS.
Carefully inspect the ejected shell. If the primer is indented,
the shell should be disposed of in a manner that would
prevent accidental injury to you or others. If there is no
indentation, your gun may have malfunctioned and
should be serviced by a qualified gunsmith. If the gun is
Pry the rim of the shell up
onto the spring cover.
under warranty, it must be serviced by a U.S. Repeating
Arms Company, Authorized Repair Center (ARC).
IMPORTANT: If your Model 9410 has not fired when
the trigger is pulled, also be sure to check your gun’s
manual hammer stop to make sure it was not left
inadvertently in the “on safe” position.
FIRING PROCEDURES
IMPORTANT: WHEN YOU ARE PREPARING TO
SHOOT, IT IS ALWAYS ESSENTIAL THAT YOU
BE TOTALLY SURE OF YOUR TARGET. ALWAYS
BE AWARE OF ALL OBJECTS BEHIND YOUR
TARGET. KNOW THE EXACT LOCATION OF
PERSONS WITH YOU AND ANY OTHERS IN
YOUR VICINITY. PICK YOUR TARGET WISELY
AND CAREFULLY.
23
Cocking the hammer to fire
FIGURE 15
Top view
Pushing the hammer
stop off with
your finger
FIGURE 16
With a loaded shell in the chamber, the manual hammer
stop in the “on” position, the hammer in the safety
(rebound) position and your finger off the trigger:
1. Firmly position your thumb on the hammer and draw
the hammer back to the full-cock position
(Figure 15).
2. Place the manual hammer stop in the “off” position
(Figure 16) by pushing it from right to left.
YOUR SHOTGUN IS NOW READY TO FIRE.
3. Firmly shoulder your gun, take aim and when on target
pull the trigger smoothly, without jerking. After firing, let
the trigger return to the fully forward position.
SPECIAL NOTE ON TRIGGER PULL: When pulling
the trigger an initial
“
take-up” section can be felt. This
longer, initial pull is an added safety feature of your Model
9410. It serves to drop an internal hammer block that is
positioned between the hammer and receiver. The hammer
block prevents the hammer from striking the firing pin
until you pull the trigger to fire the shotgun.
TO CHAMBER ANOTHER ROUND FOR THE NEXT SHOT —
1. Swing the finger lever fully down extracting and ejecting
the fired shell case from the chamber.
2. Close the action by returning the finger lever upward.
The closing of the action will transfer a new shell from
the magazine to the chamber, leaving the hammer in a
cocked “ready to fire” position.
3. WHEN THROUGH FIRING ALWAYS
IMMEDIATELY PLACE THE MANUAL
HAMMER STOP IN THE “ON” POSITION
(FIGURE 17), AND THE HAMMER IN THE
SAFETY (REBOUND) POSITION (REFER
BACK TO FIGURE 6).
24
Push the hammer stop
from left to right to the
“on” (safe) position
Top view
To fire additional shells from the magazine, simply work
the finger lever downward fully and return it to the original
upward position and repeat the firing sequence again.
WHEN FIRING IS COMPLETED OR WHEN
SHOOTING IS NO LONGER IMMINENT,
IMMEDIATELY RETURN THE MANUAL
HAMMER STOP TO THE “ON” (SAFE)
POSITION AND RETURN THE HAMMER
TO THE REBOUND POSITION.
IMPORTANT: UNDER NO CIRCUMSTANCES
SHOULD YOU MOVE ON OR CONTINUE TO
HUNT WITH YOUR HAMMER OR SAFETY IN
THE FIRE POSITION.
FIGURE 17
SIGHT ADJUSTMENTS
All Model 9410 shotguns are fitted with open sights. The
style and adjustment system may vary between models
and grades.
The proper procedure is to shoot a group or pattern with
the sights set as they come from the factory (intermediate
position on both elevation and windage), and then make
incremental adjustments to move the sight blade and
blade holder to position the group on your target. The
procedures below are for the type of open sights found on
many current Model 9410 shotguns.
BEFORE MAKING ANY SIGHT ADJUSTMENTS,
MAKE SURE YOUR SHOTGUN IS FULLY
UNLOADED AND THE MUZZLE IS POINTED IN
A SAFE DIRECTION. PLACE THE HAMMER IN
THE REBOUND POSITION AND THE MANUAL
HAMMER STOP INTO THE “ON” POSITION.
UP OR DOWN ELEVATION ADJUSTMENTS —
Adjusting elevation on your Model 9410 requires you to
lift up the rear notch blade holder on your shotgun’s rear
sight with your fingers and move the notched elevator
either forward or backward (see Figure 18). To raise point
of impact, use your fingers to lift up on the blade and slide
the elevator rearward. Adjusting the sight to make your
25
Move the elevator
forward to shoot lower, rearward
to shoot higher.
Lift up on the blade holder
FIGURE 18
Sight elevator
gun shoot lower is just the opposite — move the elevator
forward. Remember:
• Move the blade and holder UP to shoot HIGHER.
• Move the blade and holder DOWN to shoot LOWER.
RIGHT OR LEFT WINDAGE ADJUSTMENTS —
On most Model 9410 sights, the entire rear sight blade
holder is dove-tailed in the rear sight base. To adjust for
windage, gently move the rear sight blade to the right or
left by tapping at the dove-tail using a wood or fiber
dowel or hammer that will not mar the sight (Figure 19).
If you tap to the right your gun will shoot more to the
right. Moving the blade holder to the left is just as easily
done. Note how much you adjust the sight as you sight-in
your Model 9410. Remember:
FIGURE 19
Tap carefully. Do not
mar the barrel or sight.
• Move the rear sight to the RIGHT to shoot farther to
the RIGHT on the target.
• Move the rear sight to the LEFT to shoot farther to the
LEFT on the target.
Care should be taken not to mar the finish, damage
the attaching screws or bend sight components when
adjustments are made.
All sight adjustments are a matter of trial and error.
Remember, it is usually necessary to reset your sights
when you change type or even brand of ammunition.
26
SIGHT MAINTENANCE —
Occasionally check your sights to make sure they have
not been jarred or vibrated out of adjustment. This is
especially important after extensive shooting or after
hunting under rugged conditions. If so equipped, check
the two screws holding the rear sight blade in place on
the blade mount and carefully tighten if necessary. Check
the screw holding the front sight base to the barrel. This
screw can be accessed by gently removing the fiber optic
pipe from the base. Tighten the screw and carefully
re-install fiber optic pipe. Front and rear sight bases
should always be tight on the barrel and dove-tails
should be snug.
SIGHT PICTURE —
The correct sight picture for the sights on your 9410
when shooting Foster-type slugs is with the front bead
resting in the bottom of the sight blade (also called the
apex of the shallow). The bead itself should rest directly
under the point of impact (Figure 20). For example, if
you were shooting a conventional target, the round, black
bull’s-eye would appear to rest on top of the front bead.
When patterning with birdshot, the sights should be
aligned with the center of the pattern. Some shooters
may wish to position the pattern a few inches higher than
the point of aim, depending on preference and shooting
situation. The bird shot patterns you will experience
with the Model 9410, at 25 yards, would generally be
considered “full choke.”
Correct sight picture.
Target
bull’s-eye
27
FIGURE 20
Bead
Notch
HAMMER EXTENSION
Some Model 9410 rifles are supplied with a hammer
extension. A hammer extension is useful when a scope is
mounted. It extends to the side, making it convenient to
cock and lower the hammer even with a low-mounted scope.
The hammer extension can be used in either the right
hand or left hand position. To install, coat the hammer
extension threads with Loctite
®
thread locking compound.
Position the round hollow edge to the left or right as
preferred and fully tighten the hammer extension in the
tapped hole in the hammer (Figure 21). (Right-handed
shooters usually prefer mounting the extension to the
right side.)
WARNING: HAMMER EXTENSIONS CAN
LOOSEN WITH USE. OCCASIONALLY CHECK
TO MAKE SURE YOUR HAMMER EXTENSION
IS STILL ON TIGHTLY. PROPER MOUNTING
OF THE HAMMER EXTENSION IS IMPORTANT
TO PREVENT ACCIDENTAL DISCHARGE.
It is important to familiarize yourself thoroughly with the
operation and use of the hammer extension and your
firearm prior to using live ammunition.
MAGAZINE PLUG
The 9410 is delivered with a three-shot adapter plug
FIGURE 21
Insert the
threaded end into
the threaded hole
and tighten
included in the box. This plug limits magazine capacity to
two shells in compliance with federal migratory bird
(doves are migratory birds) regulations and regulations in
some states. If you do not wish to be limited to three shots
total — when it is not required by law — you can remove
the adapter plug.
WHEN REMOVING THE PLUG, BE CERTAIN
THERE ARE NO SHELLS IN THE MAGAZINE
OR CHAMBER AND KEEP THE BARREL AND
MAGAZINE POINTED IN A SAFE DIRECTION
AT ALL TIMES.
Remember, the plug and magazine cap are under spring
pressure, so care must be taken for safe removal. Always
28
FIGURE 22
FIGURE 23
Remove magazine
end cap
point the end of the magazine away from your face and in
a safe direction. Never look directly down into the cap
end of the open magazine.
ALWAYS WEAR EYE PROTECTION WHEN
REMOVING AND INSTALLING THE MAGAZINE’S
THREE-SHOT PLUG.
If you misplace or break the adapter included with your
Model 9410, contact our parts department (Page 34).
ADAPTER INSTALLATION MODEL 9410 TRADITIONAL—
1. Loosen and remove the magazine end cap retaining
screw located on the underside of the forward end of the
magazine tube (Figure 22).
2. Carefully remove the magazine end cap from the magazine.
Remember, it is under spring load.
3. The spring will rise out of the magazine tube.
3 shot adapter inside magazine
4. Place the three shot adapter inside the magazine spring
coils with the flared end of the adapter resting on the top
coil. (Figure 23).
5. Replace the magazine end cap, pushing the spring and
adapter back down into the magazine tube.
6. Replace the magazine cap retaining screw.
ADAPTER REMOVAL, MODEL 9410 TRADITIONAL—
1. Loosen and remove the magazine end cap retaining
screw located on the underside of the forward end of the
magazine tube (Figure 22).
2. Carefully remove the magazine end cap from the magazine.
Remember, it is under spring load.
3. As the spring rises out of the magazine tube, it will lift
the three-shot adapter with it.
29
FIGURE 24
FIGURE 25
Turn sling swivel stud
counterclockwise to
loosen.
4. Remove the three-shot adapter from the spring
(Figure 23).
5. Replace the magazine end cap, pushing the spring back
down into the magazine tube.
6. Replace the magazine cap retaining screw.
ADAPTER INSTALLATION MODEL 9410 PACKER —
1. Remove the two screws on the front of forearm cap
using a standard screwdriver.
2. Pass a small screwdriver through the hole in the sling
post found on the end of the magazine tube. Turn the post
counter clockwise to loosen the post. (Figure 24.)
3. Slide forearm cap forward on magazine tube. Carefully
Tilt magazine tube away
from barrel while keeping
pressure on end cap.
remove the magazine end cap from the magazine by
tilting the magazine tube away from the barrel enough
to clear the sling post mounting stud on the barrel.
Remember, magazine is under spring load.
(Figure 25.)
4. The spring will rise out of the magazine tube. Place
the three shot adapter inside the magazine spring coils
with the flared end of the adapter resting on the top coil.
(Figure 23.)
5. Replace magazine end cap, pushing the spring and
adapter back down into the magazine tube. BE SURE
To install the end cap with the flat spot around the sling
post mounting stud hole facing away from the barrel.
(Figure 26.)
30
Flat spot of end cap
faces away from barrel.
Larger hole in magazine
tube faces away from barrel.
FIGURE 26
7. Before tilting the magazine back in place on the sling
post mounting stud, note the two different sized holes in
the end of the magazine tube. The larger hole must face
away from the barrel. (Figure 26.)
8. Replace magazine tube onto sling post mounting stud.
9. Replace sling post through magazine tube and end cap.
Carefully install sling post making sure the largest part of
sling post is properly installed and passes through the hole
in the magazine tube. Failure to do so will cause damage
to the magazine tube.
10. Return forearm cap to original location and secure
forearm cap with screws.
ADAPTER REMOVAL, MODEL 9410 PACKER —
1. Remove the two screws on the front of forearm cap
using a standard screwdriver.
2. Pass a small screwdriver through the hole in the sling
post found on the end of the magazine tube. Turn the post
counter clockwise to loosen the post. (Figure 24.)
3. Slide forearm cap forward on magazine tube. Carefully
remove the magazine end cap from the magazine by
tilting the magazine tube away from the barrel enough
to clear the sling post mounting stud on the barrel.
Remember, magazine cap is under spring load.
(Figure 25.)
4. As the spring rises out of the magazine tube, it will lift
the three-shot adapter with it. Remove the three-shot
adapter from the spring (Figure 23).
5. Replace magazine end cap, pushing the spring back
down into the magazine tube. Be sure to install the end
cap with the flat spot around the sling post mounting stud
hole facing away from the barrel. (Figure 26.)
7. Before tilting the magazine back in place on the sling
post mounting stud, note the two different sized holes in
the end of the magazine tube. The larger hole must
face away from the barrel. (Figure 26.)
8. Replace magazine tube onto sling post mounting stud.
31
9. Replace sling post through magazine tube and end cap.
Carefully install sling post making sure the largest part of
the sling post is properly installed and passes through hole
in magazine tube. Failure to do so will cause damage to
magazine tube.
10. Return forearm cap to original location and secure
forearm cap with screws.
CLEANING AND MAINTENANCE SUGGESTIONS
The Model 9410 will function better and more reliably
over a longer period of time if it is properly maintained
and kept clean.
BEFORE PERFORMING ANY CLEANING
PROCEDURES, ALWAYS MAKE CERTAIN
THERE ARE NO SHELLS IN THE CHAMBER,
MAGAZINE OR ACTION/FEED AREAS.
You should clean your Model 9410 after every day of
shooting and more often if it becomes excessively dirty.
A minimum cleaning includes wiping down the action
and oiling key parts. Regular maintenance will also
include cleaning the barrel. If you encounter a function
problem (tight action when working the finger lever), be
sure to give your gun a thorough cleaning to see if it
solves the problem before seeking the services of one of
our Authorized Repair Centers, our service facility or a
competent gunsmith.
To clean your firearm, follow the general outline that follows:
CLEANING PROCEDURES —
BE CERTAIN YOUR GUN’S CHAMBER AND
MAGAZINE ARE UNLOADED. ALWAYS WEAR
PROTECTIVE SAFETY GLASSES DURING ALL
CLEANING PROCEDURES. KEEP AMMUNITION
AWAY FROM THE CLEANING AREA. DO NOT
TEST THE FUNCTION OF YOUR FIREARM
WITH LIVE AMMUNITION. ALWAYS PLACE
THE MANUAL HAMMER STOP IN THE “ON”
(SAFE) POSITION BEFORE BEGINNING ANY
CLEANING PROCEDURE.
1. Use a cleaning rod with a tip and patch suitable for the
bore diameter of your gun. Make sure the patch is large
enough for a snug fit in the bore.
Insert the rod and patch into the barrel at the muzzle
end and run it back and forth several times. Use a crown
protector if possible. Be careful not to strike the crown
of the muzzle with the handle end of the rod. Damage to
this area can affect the accuracy of your gun.
2. Inspect the chamber and bore for brass, copper and
powder fouling. A normal amount of powder residue can
be expected and is not serious. It can usually be removed
by repeating step one, using a patch saturated with solvent.
32
If or when fouling should become heavy, it can be
removed with a brass bore brush. Dip or spray the brush
with solvent and scrub the chamber and bore until the
fouling is removed. To prevent brass bristles from breaking off, the brush should be pushed completely through
the bore before being withdrawn. If cast lead slugs are
used a lead solvent may be used as well to fully clean the
bore. Follow the instructions on all solvents and cleaners.
3. After fouling has been removed the bore should be
wiped dry. Then pass a slightly oiled patch through the
bore, for preservation. A fine, light gun oil is recommended.
4. Wipe all exposed metal surfaces of the receiver, forearm
and barrel with a clean rag. Finger marks should be
removed because they provide a place where moisture can
accumulate. Any dried oil in the receiver area should also
be removed.
5. Then lightly oil your gun at the points described under
“Oiling the Action” (page 13). The metal of the gun
should receive a light film of oil any time the shotgun
has been exposed to weather or handling. Remember,
the polished, finely fitted surfaces of the receiver and
action mechanisms must always have a thin film of oil.
Make sure that the surfaces of the breech block, lever
components and feed mechanism parts are especially
clean and lightly oiled with a high quality gun oil. Do
not use pure silicone or lanolin.
6. INSPECT THE BARREL AND CHAMBER. TO
MAKE CERTAIN THAT NO PATCHES HAVE
BEEN INADVERTENTLY LEFT IN THEM.
Remove any that remain.
7. Wipe all wood surfaces.
8. When transporting only, store your gun in a quality
protective case to prevent scratches and dents. Store in a
dry place to prevent corrosion. Store away from children.
MAKE SURE YOUR GUN IS UNLOADED AND
ALWAYS STORE AMMUNITION
SEPARATELY.
OTHER CLEANING SUGGESTIONS —
• Never pour large quantities of oil into the receiver or
other parts. It can drain down to the wood and soften
it — and cause permanent damage and loosening of
the stock.
• After extended periods of heavy use, your gun should
be taken to one of our Authorized Repair Centers or a
qualified gunsmith to have the action disassembled for
professional cleaning and lubrication.
NEVER ATTEMPT TO TAKE YOUR MODEL
9410 APART FURTHER THAN EXPLAINED IN
THIS MANUAL.
33
This is a specialized, finely fitted mechanism. You may
permanently mar it by attempting to disassemble the
inner mechanism assemblies. If further disassembly for
service or cleaning is required, take your gun to a U. S.
Repeating Arms Company Authorized Repair Center or a
competent gunsmith as explained under “Service or Repair.”
PARTS, SERVICE, REPAIR AND QUESTIONS
If your Winchester rifle or shotgun should ever need
service or repair; it is often best to utilize one of our
Authorized Service Centers. In some cases it is appropriate
to use the Winchester Service Center in Arnold,
Missouri. A list of Authorized Service Centers was
included with your new firearm. If you need a new listing
call us. We can help you determine the best place to
service your firearm.
In order to avoid delays it is important to never send your
gun directly to our facility without direct authorization
from one of our service specialists. This avoids possible
delays in obtaining service. Call us for details on how to
receive service first, before sending your gun.
Parts listings, Service Center lists, service procedures and
general product information are also found on the web at:
www.Winchester-guns.com
GENERAL PRODUCT
AND HISTORICAL QUESTIONS
1-800-945-5237
Winchester Rifles and Shotguns Customer Service
275 Winchester Ave.
Morgan, Utah 94050-9333
PARTS, SERVICE, REPAIR STATUS
AND TECHNICAL QUESTIONS
1-800-322-4626
Winchester Rifles and Shotguns Parts & Service
3005 Arnold Tenbrook Road
Arnold, MO 83010-9406
CAUTION: PARTS ARE MADE FOR
CURRENT WINCHESTER BRAND GUNS
AND SHOULD NOT BE USED IN OTHER
GUNS EVEN THOUGH MODELS MAY BE
SIMILAR. IMPROPERLY FITTED PARTS
MAY BE DANGEROUS.
34
WINCHESTER-GUNS.COM
U.S. Repeating Arms Company offers an information
resource for you on the world wide web.
• List of authorized repair centers.
• Customer service information.
• Answers to many technical and historical questions.
• Links to helpful sites.
• On-line catalog
www.winchester-guns.com
NOTES
35
U.S. Repeating Arms Company, Inc.
Licensee
275 Winchester Avenue
Morgan, Utah, U. S. A. 84050-9333
www.winchester-guns.com
Winchester trademarks licensed from Olin Corporation.
AO0205/02018
Loading...