Winbond Electronics W91633, W91632, W91631, W91630 Datasheet
W91630 SERIES
10-MEMORY TONE/PULSE DIALER WITH
REDIAL FUNCTION
GENERAL DESCRIPTION
The W91630 series are Si-gate CMOS ICs that provide the signals needed for either pulse or tone
dialing. The W91630 series features a ten-channel, 32-digit automatic dialing memory.
FEATURES
• DTMF/Pulse switchable dialer
• 32-digit redial memory
• Ten by 32 digit two-touch indirect repertory memory
• Mixed dialing, cascade dialing allowed
• Pulse-to-tone (P→T) keypad for long distance call operation
• Easy operation with redial, flash, pause and P→T keypads
• Pause, pulse-to-tone (P→T) can be stored as a digit in memory
• Tone output duration: as long as key is depressed or 90 mS minimum
• Minimum intertone pause: 90 mS
• Flash time: 100/300 mS
• Uses 4 × 5 keyboard
• On-chip power-on reset
• Uses 3.579545 MHz crystal or ceramic resonator
• Packaged in 18-pin DIP
• The different dialers in the W91630 series are shown in the following table:
TYPE NO. DIALING RATE PAUSE M/B FLASH
W91630
10 ppS 4 sec
1:2
W91631 2:3
W91632 10 ppS 4 sec 1:2 100 mS
W91633 2:3
300 mS
Publication Release Date: June 1996
- 1 - Revision A3
PIN CONFIGURATION
XT
MUTE
MUTE
W91630 SERIES
1 18 R4C1
C2
C3
C4
P MUTE
V
XT
XT
T/P MUTE
SS
2
3
4
5
6
7
8
9 10
R3
17
16
R2
R1
15
14
13
12 DTMF
11
DD
V
MODE
DP/C5
HKS
PIN DESCRIPTION
SYMBOL PIN NO. I/O FUNCTION
Column-
Row Inputs
1−4
&
15−18
I
Keyboard inputs are designed for use with either a standard 4 × 5
keyboard or an inexpensive single contact (Form A) keyboard.
Electronic input from a µC can also be used.
Valid key entry is defined by a connection between a single row and
a single column.
XT,
7, 8 I, O A built-in inverter provides oscillation with an inexpensive
3.579545 MHz crystal or ceramic resonator.
T/P
9 O
The T/P
is a conventional CMOS inverter output. It is low
during pulse and tone mode dialing sequence and flash break;
otherwise, it remains high.
MODE 13 I Pulling the mode pin to VSS place the dialer in tone mode.
Pull to VDD or leave floating: Pulse mode (10 ppS, M/B = 2:3 or 1:2)
- 2 -
W91630 SERIES
HKS
HKS
HKS
HKS
DP/C5
Pin Description, continued
SYMBOL PIN NO. I/O FUNCTION
10 I Hook switch input. Conventional CMOS input with an internal
protection diode and a pull-high resistor to VDD.
= VDD: On-hook state. Chip in sleep mode, no operation.
= VSS: Off-hook state. Chip enabled for normal operation.
During dialing, this input ignores
than 150 mS (i.e., dialing is not terminated).
11 O Open drain dialing pulse output (Figure 1).
Flash key causes DP/C5 to be active in both tone mode and pulse
mode.
DTMF 12 O During pulse dialing, maintains low state at all times.
In tone mode, outputs a dual or single tone.
Detailed timing diagram for tone mode is shown in Figure 2(a, b).
OUTPUT FREQUENCY
Specified Actual Error %
R1
R2
R3
R4
C1
C2
C3
697
770
852
941
1209
1336
1477
= VDD for durations of less
699
766
848
948
1216
1332
1472
+0.28
-0.52
-0.47
+0.74
+0.57
-0.30
-0.34
VDD, VSS 14, 6 I Power input pins.
P MUTE 5 O The P MUTE is a conventional CMOS inverter output. It is high
during pulse dialing sequence and flash break. Otherwise, it
remains low.
Publication Release Date: June 1996
- 3 - Revision A3
BLOCK DIAGRAM
C1C2C3
C4
DP/C5
W91630 SERIES
XT
XT
ROW
(R1 to R4)
COLUMN
(C1 to C4)
DTMF
KEYBOARD
INTERFACE
D/A
CONVERTER
FUNCTIONAL DESCRIPTION
HKS
MODE
READ/WRITE
COUNTER
RAM
LOCATION
LATCH
ROW & COLUMN
PROGRAMMABLE
COUNTER
SYSTEM CLOCK
GENERATOR
CONTROL
LOGIC
PULSE
CONTROL
LOGIC
DATA LATCH
& DECODER
T/P MUTE
P MUTE
DP/C5
Keyboard Operation
1 2 3 S
P→T
4 5 6 F P R2
7 8 9 A R3
* 0 # R R4
• S: Store function key
• F: Flash key
• P→T: In pulse mode, this key works as Pulse→Tone key
• R: The redial function can be excuted only as first key-in after off-hook.
• A: Indirect repertory dialing key
• P: Pause key
- 4 -
R1
W91630 SERIES
Normal Dialing
OFF HOOK , D1 , D2 , ..., Dn
1. D1, D2, ..., Dn will be dialed out.
2. Dialing length is unlimited, but redial is inhibited if length oversteps 32 digits in normal dialing.
3. Dialing mode is determined at the on/off hook transition.
Redialing
1. OFF HOOK , D1 , D2 , ..., Dn , Busy,
Come
, R
The R key executes the redialing function.
2. Redial content = D1, D2, ..., Dn
OFF HOOK , R , D1' , D2' ,
a. D1, D2, ..., Dn, D1', D2', P→T, D3', D4' will be dialed out.
b. Redial register is changed to D1, D2, ..., Dn, D1', D2'.
3. Ln content = D1, D2, P→T, D3, D4
OFF HOOK , A , Ln
then ON HOOK , OFF HOOK , R
4. OFF HOOK , A , Lm , A , Ln , A , Lp
Busy, then ON HOOK , OFF HOOK , R
a. The digits stored in Lm, Ln, and Lp will be dialed out after the R key is pressed.
b. If length oversteps 32 digits, redial is inhibited.
c. Redial register stores not only normal dialing digits but also repertory or mixed dialed numbers.
d. Redialing is valid for first key-in only.
, will dial out D1, D2, P→T, D3, D4
P→T
, D3' , D4'
will dial out D1, D2, P→T, D3, D4.
ON HOOK , OFF HOOK
Number Store
1. OFF HOOK , S , D1 , D2 , ..., Dn , A , Ln , ON HOOK
a. D1, D2, ..., Dn will be stored in memory location Ln but will not be dialed out.
b. Ln = 0 to 9; Dn = 0 to 9, *, #, Pause, P→T.
Publication Release Date: June 1996
- 5 - Revision A3
Loading...